Hi guys, I hope I can type this coherently.
I have a g3 wizard that I have flashed many times over the last year or so. Lately the power button has stopped working. I can get the phone to turn on by plugging it in, and then holding in the camera/voice buttons and THEN hitting the power button. It goes into the rainbow screen, and I just soft reset via the hole on the side. At that point it is on and running fine, but the power button does nothing.
The power button does nothing at all unless I plug the phone in, and then only if I go to bootloader. It seems to work just fine to do that-which is what is stumping me. I thought the button was just broken. The charge/battery lights do come on.
For now I have it set to never turn off, so I try to make sure it doesn't run too low. The battery life seems ok. Any tips? I want to be able to put the phone to sleep again...
thanks
I have problem with power button. when push pwr button dont,t off pda, but when hold pwr then lights off.
Power is never shut off in PDAs, thats the way PDAs have been designed.
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
afbcamaro said:
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
Click to expand...
Click to collapse
Do you have a problem with turning on? First, we need to know whether it is hardware issue or not...
What you can do in the mean time with the turning off problem is by installing a poweroff app like shutdownme, psshutxp, etc etc...
Absolutely no problem with turning on from standby... Right now i just lock the phone before placing it back in the holster.
To make it clearer if you HOLD the power button down the backlight will turn off only. It will still show the display image and keys will still function (it dims)
Well, I had the same issue with the latest WM5 ROM. I thought I was too stupid to press the button, then I thought the button was broke, then I thought, I'll have to live with it.
Now that I have flashed to WM6, no problems at all! Never even came to my mind that this problem once existed. So I guess that some ROMs just have this particular bug?
Stefan
I have tried all the roms as well as 2003 and have the same issue in all of them. And im not alone.
Power off Problem
I'm in same condition.
Had the same problem when using WM2003 second Ed.
Now I've installed WM6 but nothing changed:
I cannot power-off/suspend but can turn off backlight if press and hold power button.
When in standby the button works fine to turn on the device.
Also, sometimes volume turns up continously with "noisy" beep ...
Anybody solved this problems?
Thanks,
Ruben
(WM 6 - 5.60.00 build 18125.0.4.2
radio 1.12.00 )
Power button has two modes:
1. Click mode: Click it once for a short duration. This turns off backlight and can be resumed by pressing it again or by pressing OK button
2. Press and Hold mode: Press and hold for few seconds and release. This mode will dim the backlight and no other button will bring it back. This is some kind of deep sleep in battery mode. To resume the original setting, press and hold Power button again for few more seconds.
(p.s.: I am not sure if this behavior is true for all the BA models)
April 1,
I know these modes...
It seems that "mode 1" doesn't work at all...
I would activate "Button Lock" (settings-->button--> Lock(tab)--> "lock all buttons except power button") to turn-off backlight and "lock all buttons except power button" but I cannnot...
You solved this problem?
I have had this issue of not being able to power off. One way I always got out of it was by clearing the registry hive. Unfortunately this brings the PDA back to the basic ROM. At this point the power button worked without any issues. Upon reloading the software the problem may come back. I believe the issue is related to some programs. I can't recall which program it was that seemed to cause the issue. One other thing I think that also worked was just entering the registry and getting back out and doing a hard reset.
I had the same problem with my 6600. the message button also didn't work. Believe it or not, to fix it. I banged the lower half (4-way area) on my desk a few times. Not hard enough to break the screen. But prolly hard enough to free what was prolly a sticky key. And now everything is working.
i am too
the same ...
when i press the power quickly , nothing happen
when i press the power for 2 sec. the backlight turns off
i tried every thing .... including formatting my BA
any one solve it ???
I have this same problem, my power button does`t work. i tried installing different roms but without any chance to fix it. maybe its an mechanic issue. i will change pwr button, i hope this work.
Look at one of my previous posts. I fixed it, twice, and other users have used the same metod to fix it. I think the problem is "hung bit" hardware related because you can also send it in for service, and they will change a chip, but i never had to.
I was using my phone today, and now all of a sudden, the power button is completely non functional, and every 10 seconds, I get a "Do you want to power off" prompt on my phone as if the power button was being continuously pressed, but it is not. What could have gone wrong?
Any Luck?
I currently have the exact same issue. I lost my phone, and the person who found it returned it. Eversince then the power button doesn't work and I get the same warning.
After lots of hard resets and a new ROM flash, I was good to go.
Hi,
i have a htc touch hd with energy rom installed, i have read about the volume problem with this rom but i would like to make sure this is software related before i got any further, anyway heres my problem - as soon as i switch the phone on, everything loads then the volume up button presses itself constantly, causing the phone to constantly beep, if i then restart the phone, it vibrates 3 times and fails to come on, i have to remove the battery for a minute or so to get the phone back on then the same happens again.
so i installed the latest version of energy rom and it still happens except the volume control screen has been removed so now whenever im in a menu or drop box, it constantly changes the selected item to the option above (as if im physically pressing the volume up button).
is this software related or is the volume button physically broken.
the reason i ask before trying the patch is because the phone will need reflashin to be able to install the patch (because it will not work with the vol button stuck) and if i reflash with a stuck volume button it might crash and brick the phone. if its a hardware fault i am capable of fixing it myself.
Hi,
After a night in a tent my HTC HD2 started to malfunction. When turning on the device I noticed it said ''safe mode'' (Android NAND (sensation rom)). At first I didn't think much of it, because I thought the device had turned of due to a dead battery. However after leaving it for a while to recharge I noticed that after each reboot it would return to safe mode. Then I noticed that the device kept showing that it was in vibration mode --> the volume down button is stuck(not physically though). Also the device kept popping up ''recent activities''... I'm under the impression that this is due to a malfunctioning call button, not a 100% sure though.
After I reflashed it to wm 6.5 the problem still prevails. However I was able to get a more detailed view of the issue:
The windows button lacks every response, the call button does not respond on touch but seems to randomely activate the call function. The home button functions poorly. However the back button, power on button and volume up button function correctly.
The volume down button seems dependent on the other buttons. When pushing one of the buttons below the screen the volume down button is activated and is stuck untill the screen is turned on and off. However the volume up button does not yield such a result. The volume down button still is responsive to touch though, as long as it is not stuck.
Any ideas how to solve this problem, or how to work around it? As a precaution I put the HD2 in a box with a moisture absorber.
Hi. I wish I could give you a better understand that what I can offer but what I think happened is you probably rolled onto your phone while sleeping.
This is not to say your problem could have came from something else but let me explain a little about safe mode.
Safe mode anyone can enter by pressing volume down and holding it while it boots up. It allows the developer a safe mode they can enter similiar to
why your computer has it installed on it. Normally pulling the battery and letting the phone reboot clears this out though. With that being said i think what
has happened is the volume button has stopped working as it should. There are several sites you can go to here on the web to send your phone out
to have it looked at and fixed. All in all it shouldn't be that costly and if your mechanically inclined and (careful) it shouldn't be to hard to do it yourself. I
would make sure you take very good notes/pictures in dismantling your phone because if you put it back together wrong you can make the problem worse.
Ebay, listing found here has the volume button and the tools necessary to open your phone and repair the volume key for around $7 usd.
Please make sure your phone model is supported and you have the know how to do this without making things a bigger issue. I would also
suggest to wait for more info because I could be wrong as well.
Thanks for your time, effort and information.
However I don't think it is a problem caused due to physical damage to the volume button. In addition the phone was in a 'sidepocket' of the tent, making it virtually impossible to roll onto it. Because the call button is malfunctioning as well I can imagine it being motherboard related, addmittedly I am not much of an electrician .
The issue has been partly resolved. Only one problem still exists. When I push the windows button it results in a volume up response. I performed a hard reset but the problem still persists, any ideas what could cause this?
Cheers
The hd2 high level of integration can not fall. Even without the screen broke, other things will break, so the sets of sets of silicone can not throw. Screen indeed not easy to break unless it fell out just in time to have something to knock to the screen.