hi everyone..
i think i bricked my phone yesterday.. after update of the radio (6.35.08.29) the phone now wont start...
the only thing i get is the htc hero boot logo (a phone with a green arrow on left side and a gray arrow on right, with the text HTC underneeth) and after some time it (about half an hour the phone turns off)
i am planning to take the phone to repair, and saying it happend during one of the htc updates..
but if someone out there could help me unbrick i would really appreciate it.
BTW, phone cant get into fastboot, HBoot and recovery mode.. i tried almost everything
heeelp me..
thx everyone i bow before the community
IstBarP said:
hi everyone..
i think i bricked my phone yesterday.. after update of the radio (6.35.08.29) the phone now wont start...
the only thing i get is the htc hero boot logo (a phone with a green arrow on left side and a gray arrow on right, with the text HTC underneeth) and after some time it (about half an hour the phone turns off)
i am planning to take the phone to repair, and saying it happend during one of the htc updates..
but if someone out there could help me unbrick i would really appreciate it.
BTW, phone cant get into fastboot, HBoot and recovery mode.. i tried almost everything
heeelp me..
thx everyone i bow before the community
Click to expand...
Click to collapse
I had almost exactly the same problem, nothing works for me. Phone keeps rebooting after HTC logo. recovery is no go.
HTC service center needs to replace the motherboard in the end.
good luck
Are you certain that you cannot even get into fastboot? Take battery out, unplug the usb cable and put the battery back in to stop it from getting stuck in a reboot cycle and then hold back and power on.
If you cannot even get into Fastboot then thats about as bricked as you can get i'm afraid.
I performed a SPL flash, the phone rebooted ,it took long time rebooting so i got panicked i pulled out the battery ( wasn't a smart move ).
tried to start the phone.. now i was stuck at the first splash screen.
-pulled out the battery and back again start the phone... stuck at the first splash screen or boot looping endlessly,
-did all possible key combinations to get in fastboot, recovery mode... nothing.
-cried for help, got directed to a post similar to mo my case... worked for me hope it dose for everyone else.
here is what i did (followed):
-On the PC, i ran the command 'fastboot boot recoveryimage.img'.
-At this point the command says 'waiting for device' (or something like that).
-I removed the battery.
-went sleep
-woke up in the morning, went back to my old duct taped SE phone
-came home in the evening
-I Connected USB.
-I inserted the battery.
-I booted the phone while holding the HOME key.
-The phone still froze at the first splash screen, but then suddenly, the waiting fastboot command detected the phone and booted the recovery image!
flashed again but this time checked all steps twice before i check them a third time, and flashed the SPL and radio and the rom.
IstBarP said:
hi everyone..
i think i bricked my phone yesterday.. after update of the radio (6.35.08.29) the phone now wont start...
the only thing i get is the htc hero boot logo (a phone with a green arrow on left side and a gray arrow on right, with the text HTC underneeth) and after some time it (about half an hour the phone turns off)
i am planning to take the phone to repair, and saying it happend during one of the htc updates..
but if someone out there could help me unbrick i would really appreciate it.
BTW, phone cant get into fastboot, HBoot and recovery mode.. i tried almost everything
heeelp me..
thx everyone i bow before the community
Click to expand...
Click to collapse
sounds like you may have not installed radio/spl in the proper order.. shouldnt be a problem if you can get into fastboot... please tell us exactly what you did, and in what order..
hey,.. sorry for the long time since last time..
i sended in my phone
i couln't get into either fastboot or nothing else.. the CMD said waiting for device when tried to fastboot while in logo..
the only thing i could get into (that booted otherwise) was the action + power
i first updated followed a toturial where i updated my phone.. first spl, then radio, and then recovery img..
but since i read about people having probs with a radio where the phone boots but after a 4 secs restart i installed a new radio and thats where the probs started happening.. and then i could not get past the boot logo..
thx for the many answers and sorry i first come back now to see ..
if they cant fix my phone i will try follow ur guide Ch3w
BTW
as soon as i get my phone back i am up for another go i think..
i got a sapphire 32a.. can anyone give a link to a good tutorial?
thx
From my limited knowledge, u are always supposed to update radio first then spl then recovery.
http://forum.xda-developers.com/showthread.php?t=605239
yeah
achillies400 said:
From my limited knowledge, u are always supposed to update radio first then spl then recovery.
Click to expand...
Click to collapse
I followed that exact one.. but when the 6.35.10.18 failed (kept reboot every 3-5 sec) i decided to install the 6.35.08.29 instead and thats where it failed.. :/
THIS! NOW! COME ON!
This is my problem also! Please help me to un-brick.
As I saw on youtube, it's a 'semi-brick'.
It's not a brick if you can go into fastboot.
Riffbox unbrick
Sent from my HTC Desire using XDA App
Sorry to hear mate, hope it gets fixed. Don't really have any helpful suggestions for the un-bricking part, but next time upgrading radio etc., I'd suggest using Eyegor's radio switcher. Although if you sent it to the dealer, you'll probably have to re-root if they fixed it (but I know, that you know how to do that, you helped me in my early days )
I'll keep my fingers crossed!
Try this. i tried and it worked for me. press the power button and home together and push the battery in at that time. it would take you to recovery .
Ok, the guy I sent it to, couldn't make something, so the phone will return to me, possibly tomorrow.
rensenin said:
Try this. i tried and it worked for me. press the power button and home together and push the battery in at that time. it would take you to recovery .
Click to expand...
Click to collapse
It didn't work :\
Hi i had the same prblem with mine ,, push power when you see the Htc logo push the Back button and hold it there until you get in to Fastboot ,, worked for me
Whiskas2009 said:
Hi i had the same prblem with mine ,, push power when you see the Htc logo push the Back button and hold it there until you get in to Fastboot ,, worked for me
Click to expand...
Click to collapse
Didn't work for me.
I'm also stuck after flashing Radio update....
Now i got this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
And now nothing else shows up. Not fastboot, not recovery, nothing. Just this damn icon.
Ideas?
Phk said:
I'm also stuck after flashing Radio update....
Now i got this:
And now nothing else shows up. Not fastboot, not recovery, nothing. Just this damn icon.
Ideas?
Click to expand...
Click to collapse
try installing a normal RUU .. that should do it .. depends on your computer some times finding the phone though..
this thread died more than a half year ago when i created it :/.. in the end I send my phone to the repair shop
Related
Hey guys this maybe the wrong section but i have a solution for you guys if you are stuck on G1 logo in another words if your phone is bricked!
simply take your current sd card out of the phone on which you did the jailbreak, put it in the computer and delete the current update.zip file and put the working firmware on it. i tried the rc33 and of course rename it to update.zip put it in the sd card, now put the sd card back in the phone and go boot screen by holding the home and power button alt+l for menu then alt+w to wipe then alt+s to update and let it run after finished press home and back arrow to reboot and you are all set! went through the same thing tonight and was stuck but i tried it and is working perfectly fine! and sorry for those who might have resolved this issue in another thread. just was too excited to give u guys the good news! tell me if this works for you!
Good Luck!
thats not a bricked phone bricked is when no recovery or no bootloader
waqas9240 said:
Hey guys this maybe the wrong section but i have a solution for you guys if you are stuck on G1 logo in another words if your phone is bricked!
simply take your current sd card out of the phone on which you did the jailbreak, put it in the computer and delete the current update.zip file and put the working firmware on it. i tried the rc33 and of course rename it to update.zip put it in the sd card, now put the sd card back in the phone and go boot screen by holding the home and power button alt+l for menu then alt+w to wipe then alt+s to update and let it run after finished press home and back arrow to reboot and you are all set! went through the same thing tonight and was stuck but i tried it and is working perfectly fine! and sorry for those who might have resolved this issue in another thread. just was too excited to give u guys the good news! tell me if this works for you!
Good Luck!
Click to expand...
Click to collapse
waqas9240 said:
Hey guys this maybe the wrong section but i have a solution for you guys if you are stuck on G1 logo in another words if your phone is bricked!
simply take your current sd card out of the phone on which you did the jailbreak, put it in the computer and delete the current update.zip file and put the working firmware on it. i tried the rc33 and of course rename it to update.zip put it in the sd card, now put the sd card back in the phone and go boot screen by holding the home and power button alt+l for menu then alt+w to wipe then alt+s to update and let it run after finished press home and back arrow to reboot and you are all set! went through the same thing tonight and was stuck but i tried it and is working perfectly fine! and sorry for those who might have resolved this issue in another thread. just was too excited to give u guys the good news! tell me if this works for you!
Good Luck!
Click to expand...
Click to collapse
Really....Really
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
waqas9240 said:
Hey guys this maybe the wrong section but i have a solution for you guys if you are stuck on G1 logo in another words if your phone is bricked!
simply take your current sd card out of the phone on which you did the jailbreak, put it in the computer and delete the current update.zip file and put the working firmware on it. i tried the rc33 and of course rename it to update.zip put it in the sd card, now put the sd card back in the phone and go boot screen by holding the home and power button alt+l for menu then alt+w to wipe then alt+s to update and let it run after finished press home and back arrow to reboot and you are all set! went through the same thing tonight and was stuck but i tried it and is working perfectly fine! and sorry for those who might have resolved this issue in another thread. just was too excited to give u guys the good news! tell me if this works for you!
Good Luck!
Click to expand...
Click to collapse
sorry to burst your burst your bubble but that is not the brick that everyone is talking about. brick means no recovery or bootloader as previously stated.
now onto the questions
1. why were you going for rc33?
2. why is your recovery image that old?
3. -insert sarcastic question in here-
omg lol
this "solution" is posted everywhere hahaha
this is a soft brick. A brick is when you can ONLY see the G1 loading screen, nothing else. If you can get into bootloader (Cam+Power) or recovery (Home+Power) then your not bricked. We are still looking for a solution to that however.
A lot of people have been calling that a brick even though technically its not. Thats probably why you thought it was a brick. Thanks for trying to help though. im sure someone will find this thread useful
sorry guys and thank you!
Thank you guys for letting me know this is not bricked! nd maybe it would help someone like me who is still new to this!
now onto the questions
1. why were you going for rc33? (couldnt find a working link for other firmware)
2. why is your recovery image that old? ( now i have 1.5 but still looking for a better mod)
3. -insert sarcastic question in here- ( not sarcastic but whats the best firmware for this as of right now?) and if u can give me the link for it!
again thank you guys for ur response!
Well you can use Cyanogens 1.4 Recovery Image. Thats probably the best right now. and RC33 is OLD (since like before May, donut is at 1.6 now)
You can search for Cyanogens 4.1.999 ROM, Akirah's 3.0 ROM, or Enomthers ROM
those are the main cupcake builds updated to 1.6
i prefer to suggest amon ra dream recovery since it has more options and auto partition in it
just a modded cm-recovery1.4 recovery
here's the link to it
http://forum.xda-developers.com/showthread.php?t=566669
and here is a link to cyanogen's 4.1.999 make sure you follow the instructions
http://forum.xda-developers.com/showthread.php?t=567610
Truly Bricked
I don't know where to post this anymore... There are so many "Brick - Unbrick" threads now its almost ridiculous. I am wondering why anyone hasn't figured out how to push the ROM to the actual hardware with just a usb cable and the proper programing. I am assuming of course that the manufacturer or the ROM chip does something similar to this when the device is first manufactured. Wouldn't there be some one who has figured this out? Isn't that basically how it works? Isn't that basically the same principal? Somehow forcing the hardware to run when there is no ROM flashed to the hardware?
Well i dunno if it will help any, its just my own rambling thoughts, and i figured maybe some one is a lot more capable than me might benefit from the idea....
what happens to all bricked (hard bricked) phones
although a truly bricked phone can be used for spares and repairs but how much would it cost to buy one brick?
I need to buy one bricked g1 urgently guys. any help at all?
Hello, i was trying to charge my nexus 4 couse it wouldn't turn on but after an hour it still didn't turn on.
So after trying a liitle wile to turn it on i held all three buttons (power, volume up & down) and now it says "Download Mode".
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Never heard of this mode. Try connecting ur phone to pc and see if it gets detected. That would be nice to know.
gt-kingz said:
Never heard of this mode. Try connecting ur phone to pc and see if it gets detected. That would be nice to know.
Click to expand...
Click to collapse
srry just restarted (it don't appear on the computer, can check with lsusb on ubuntu but not now)
How to do it!
How to get into Download Mode
Boot into bootloader and hold all three buttons
It's LG's version of Samsung's Odin mode. However, there isn't a leak of the utility yet.
There is a long tutorial on how to use it in the Nexus 4 service manual floating around.
Basically it's worthless for us until that utility leaks.
El Daddy said:
It's LG's version of Samsung's Odin mode. However, there isn't a leak of the utility yet.
There is a long tutorial on how to use it in the Nexus 4 service manual floating around.
Basically it's worthless for us until that utility leaks.
Click to expand...
Click to collapse
I'm not entirely sure, but I think that "Download mode" interfaces with LGNPST. From my understanding, it's not publicly available, but...
Anyway, this is an interesting thread.
efrant said:
I'm not entirely sure, but I think that "Download mode" interfaces with LGNPST. From my understanding, it's not publicly available, but...
Anyway, this is an interesting thread.
Click to expand...
Click to collapse
Interesting indeed. So it looks like I'm wrong. Most of that stuff is way over my head though.
Sent from my Nexus 7 using xda premium
When I first rooted I flashed a bad recovery that deleted all my stuff and got into DL mode 3 times, I panicked. Somehow I managed to get back into boot loader and after that flashed stock boot.IMG and re-rooted...
Sent from my Nexus 4 using xda app-developers app
309041291a said:
When I first rooted I flashed a bad recovery that deleted all my stuff and got into DL mode 3 times, I panicked. Somehow I managed to get back into boot loader and after that flashed stock boot.IMG and re-rooted...
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
i'm in the same situation and appropriate anybody's help to get me back into the right track.
So what happened with this? Mine just did the same while doing the rooting of my phone. I've been using MSKIP's tutorial amongst other youtube videos showing his option in depth. No idea what happened but now I'm stuck in this "brick" or "soft brick" mode like you guys were saying earlier. What is the solution? I don't see any other pages in this thread and I'm a total noob with this stuff.
**Edit**
Fixed mine, was waiting for a while like it said but I finally powered it one, did a factory reset, and re-did everything else that comes with the 1 CLICK FOR ALL button on mskip's toolkit. Everything is perfect now and I hacked it, whoo hoo!
easy fix... working..
Jbele said:
Hello, i was trying to charge my nexus 4 couse it wouldn't turn on but after an hour it still didn't turn on.
So after trying a liitle wile to turn it on i held all three buttons (power, volume up & down) and now it says "Download Mode".
Click to expand...
Click to collapse
this same problem happened to me today.. don't worry there is a fix...
1.Get into bootloader ( Press all three buttons at same time)
2.flash google factory image from fastboot. get factory images from here... https://developers.google.com/android/nexus/images ..
3.If you dont know how to flash use mskip's toolkit for nexus 4 and flash it... (best for new users like me) get mskip's toolkit from here... http://forum.xda-developers.com/showthread.php?t=1995688
ALL THANKS TO MSKIP'S TOOLKIT
if you have queries or want detailed information comment below
NICE FEELING WHEN YOU SEE DOWNLOAD MODE... WORTH EXPERIENCING THE MINI HEART ATTACK..
DON'T WORRY ITS NEARLY IMPOSSIBLE TO BRICK NEXUS 4..
:good::good::good: ALL THE BEST:good::good::good:
HOPE THIS WORKS
shengovind said:
this same problem happened to me today.. don't worry there is a fix...
1.Get into bootloader ( Press all three buttons at same time)
2.flash google factory image from fastboot. get factory images from here... https://developers.google.com/android/nexus/images ..
3.If you dont know how to flash use mskip's toolkit for nexus 4 and flash it... (best for new users like me) get mskip's toolkit from here... http://forum.xda-developers.com/showthread.php?t=1995688
ALL THANKS TO MSKIP'S TOOLKIT
if you have queries or want detailed information comment below
NICE FEELING WHEN YOU SEE DOWNLOAD MODE... WORTH EXPERIENCING THE MINI HEART ATTACK..
DON'T WORRY ITS NEARLY IMPOSSIBLE TO BRICK NEXUS 4..
:good::good::good: ALL THE BEST:good::good::good:
HOPE THIS WORKS
Click to expand...
Click to collapse
it happened to me now, when the battery was dead. when i connect the phone to a wall charger i got the download mode massage ,
when i'm pressing all 3 buttons the phone makes a vibe (like a boot vibe) and the the red light is flashing on/off
no bootloader.
what to do?
havlaz said:
it happened to me now, when the battery was dead. when i connect the phone to a wall charger i got the download mode massage ,
when i'm pressing all 3 buttons the phone makes a vibe (like a boot vibe) and the the red light is flashing on/off
no bootloader.
what to do?
Click to expand...
Click to collapse
You should try to get into the fastboot mode first, when the phone is off, Hold Power + Volume Download button. If you can get in the fastboot menu, then use instruction above to reflash your device.
If you can't, you might be able to recover your phone using Download Mode: http://forum.xda-developers.com/showthread.php?t=2347060
havlaz said:
it happened to me now, when the battery was dead. when i connect the phone to a wall charger i got the download mode massage ,
when i'm pressing all 3 buttons the phone makes a vibe (like a boot vibe) and the the red light is flashing on/off
no bootloader.
what to do?
Click to expand...
Click to collapse
Red light due to battery low..
All you have to do is charge the phone for about six hours on the wall charger..
Then try booting your phone ..
If there's only bootloader and phone isn't booting flash factory from fastboot..
Plug it to wall charger over night.. Then try to get to download mode..
Try this to get out of red light only if there is absolutely no other way..: http://forum.xda-developers.com/showthread.php?t=2250454
If there is no boot loader whatsoever even after trying for a hell lot of time, only download mode, then do this..
http://forum.xda-developers.com/showthread.php?t=2347060
sent from my Prevert nexus
psak said:
i'm in the same situation and appropriate anybody's help to get me back into the right track.
Click to expand...
Click to collapse
When you are in download mode, press and hold Vol Down and Power, that should bring up fastboot mode, which you can use to flash another recovery...
[email protected] said:
When you are in download mode, press and hold Vol Down and Power, that should bring up fastboot mode, which you can use to flash another recovery...
Click to expand...
Click to collapse
Try Pressing power button alone for 10 sec or so...
Should do the trick
Having the same problem. I was on purity rom(4.4.3), with default purity kernel. I flashed the Ak poseidon kernel, with Ukm. It booted fine , was on phone for about 4 minutes, and then I ran antutu benchmark. Before that I didn’t change anything via synapse app. Then when I ran test on antutu phone went off. Non of the buttons were responding. I plugged the phone into wall charger and pressed all 3 buttons. Then the download mode appeared. Left it like that on the charger , went to sleep. When I woke up the phone was turned off. Today I was flashing factory img ( 4.4.3. occam). Following the instructions http://forum.xda-developers.com/nexus-4/general/how-to-how-to-flash-factory-image-t2010312 [/URL]. Everything went ok no problem in the cmd , only the thing was , when I had to fastboot the booth loader, then the phone stuck in power on loop . ( reboots, then it says google, and reboots again) I was able to stop this by holding volume down, then it goes into bootloader. Finished flashing factory img, like it says on the tut. And the same thing happens. The phone won’t boot, And it is not responding when it is unplugged. Please help :/
---------- Post added at 03:28 PM ---------- Previous post was at 03:26 PM ----------
shengovind said:
Red light due to battery low..
All you have to do is charge the phone for about six hours on the wall charger..
Then try booting your phone ..
If there's only bootloader and phone isn't booting flash factory from fastboot..
Plug it to wall charger over night.. Then try to get to download mode..
Try this to get out of red light only if there is absolutely no other way..: http://forum.xda-developers.com/showthread.php?t=2250454
If there is no boot loader whatsoever even after trying for a hell lot of time, only download mode, then do this..
http://forum.xda-developers.com/showthread.php?t=2347060
sent from my Prevert nexus
Click to expand...
Click to collapse
I will try to reconnect the battery now, maby that will help----
Fixed it !
ripped.animal said:
Having the same problem. I was on purity rom(4.4.3), with default purity kernel. I flashed the Ak poseidon kernel, with Ukm. It booted fine , was on phone for about 4 minutes, and then I ran antutu benchmark. Before that I didn’t change anything via synapse app. Then when I ran test on antutu phone went off. Non of the buttons were responding. I plugged the phone into wall charger and pressed all 3 buttons. Then the download mode appeared. Left it like that on the charger , went to sleep. When I woke up the phone was turned off. Today I was flashing factory img ( 4.4.3. occam). Following the instructions http://forum.xda-developers.com/nexus-4/general/how-to-how-to-flash-factory-image-t2010312 [/URL]. Everything went ok no problem in the cmd , only the thing was , when I had to fastboot the booth loader, then the phone stuck in power on loop . ( reboots, then it says google, and reboots again) I was able to stop this by holding volume down, then it goes into bootloader. Finished flashing factory img, like it says on the tut. And the same thing happens. The phone won’t boot, And it is not responding when it is unplugged. Please help :/
---------- Post added at 03:28 PM ---------- Previous post was at 03:26 PM ----------
I will try to reconnect the battery now, maby that will help----
Click to expand...
Click to collapse
After reconnecting the battery, I managed to boot the device. But i got gazzlion errors, non of the apps were responding. I got the msg to delete the partion or my device will not function properly. Since I have already flashed the factory img I booted to stock recovery. And deleted all user data , (factory reset). Then the device booted normally. I have lost my recovery img but what the hell I don’t care now Flashed the CMW touch, and super user. Now everything works fine
Fix - Volume Up + Power
I had the same problem this morning and found an easier fix on Google product forums.
Push Volume Up + Power button until it works. Worked for me
<not able to paste link as I'm still a n00b user and this is among my first ten posts here. Ok, this is my FIRST post here>
I got the same thing too...
Hello Guys!
My Problem (I've looked for about 2 hours in the forum, but can't find anything similar to my situation):
Got my new LG G2 (D802, 32GB, Android 4.4.2) today. I wanted CyanogenMod on it, so i unlocked it, etc...
But as i have installed in recovery mode, and after that i always got stuck at the CM 10.2-Boot screen i decided to install the stock android back onto it.
i went into download mode, choose the right .kdz-file and tried to flash it with LG Flash tool 2014.
But it got stuck there at 20%. My current situation: I can't get out of the screen where it says "Firmware upgrade and 0%, und below is "B75" and "rooted". When i press the power button for some seconds the screen gets black, then the LG logo appears and immediately the Firmware-upgrade-screen appears, again with "0%" and "B75" and "rooted".
I also can't get into recovery mode: When it push volume down and power butten, and it asks me to do a factory hard reset and i press the power button to confirm (when normally then the recovery mode menu appears) it changes automatically again to the Firmware-upgrade-screen.
Thanks in advance, hope you can help!
Were you doing all this with the phone still plugged in? If so disconnect and long press power for 15 seconds. Then again try to enter recovery. If you still can't get in, power off and retry download mode again with a fresh connection.
it's not working.. i've powered the phone off, then i get with volume down and power button to the screen where i have to confirm twice with the power button and them next comes the firmware upgrade page...
i have also no chance to get into the download mode with volume up and connect cable..
any other ideas?
florianbb said:
it's not working.. i've powered the phone off, then i get with volume down and power button to the screen where i have to confirm twice with the power button and them next comes the firmware upgrade page...
i have also no chance to get into the download mode with volume up and connect cable..
any other ideas?
Click to expand...
Click to collapse
Well what you're describing there IS download mode. At the top it says firmware update. The progress bar reads zero until it detects an update being performed. Like this...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
That's download mode. Maybe check in device manger (if windows) while the device is plugged in and on that screen. Does it show up as LGEAndroidnet USB serial port? If yes, that's the proper indentification as well. If not, how is it showing up?
Hello,
yes in device manager it shows up as "LGE AndroidNet USB Serial Port (COM6).
My G2 is exactly stuck like the one in the picture you've sent.
I thought i could try this solution on ubuntu:
http://forum.xda-developers.com/showthread.php?t=2582142
But it also can't fix it, because when i plug my G2 in, ubuntu says: "MTP-Device could not be read."
Thanks in advance!
how you repair LG G2? My phone was not rooted, but today make offical LG G2 Lollipop update, and now have this problem. Stuck in Firmware update..
florianbb said:
Hello,
yes in device manager it shows up as "LGE AndroidNet USB Serial Port (COM6).
My G2 is exactly stuck like the one in the picture you've sent.
I thought i could try this solution on ubuntu:
http://forum.xda-developers.com/showthread.php?t=2582142
But it also can't fix it, because when i plug my G2 in, ubuntu says: "MTP-Device could not be read."
Thanks in advance!
Click to expand...
Click to collapse
Problem solved warranty service. Update KitKat soft, but no't have offical info and lollipop update. I don't understant that LG Suite have yesterday update.
Same problem here,
my LG G2 D802, unrooted phone with official 4.4.4 got message to update it to lolipop, and I am now stuck on Firmware Update screen.
LG Mobile Support tool, was showing that I am making progres, but on the status bar i got stucked on 32%, then I started again, and then got error on 40%, then started again through LG mobile Support tool and got to 50%, and the same to 60%, then 70%, and this last time i am stucked on 92% and my LG Mobile Support tool forced close.....
And now its downloading again update, and maybe now it will go with all 100 %, dont know what to do.. this is so....
I thought it was driver related problem, but i changed machine, from pc to lap top, and the same thing is happening..... Every time it stops, first it writes on mobil screen with red letters ASSERT
and on status bar on LG MST it freezes, but as i sad, every time i get more % very strange
Same here - unrooted stock KK d802 - started doing the update, it failed, now stuck on the firmware screen with no way out...
i had the same problem, after several times i gave up and tried kitkat to revert back. Errors kept going but after several times it reached 100% and i am in kitkat now. I will try again today.
Yup, its probably somethnig wrong with the software that they rolled up to us.... after 10th time, it reached to 100%, but know i am stuck without network and signal,
and I get error messages "proces android.com has stoped" on every 3 seconds, I am losing my mind here realy
Do not update it, just wait for a few days, until they fix this
This is first time in my life, that I bought android phone, and that i didnt touched it, unlock it or root it, and with offical update i am having problems that i never had with custom roms
Gradjevinac said:
Yup, its probably somethnig wrong with the software that they rolled up to us.... after 10th time, it reached to 100%, but know i am stuck without network and signal,
and I get error messages "proces android.com has stoped" on every 3 seconds, I am losing my mind here realy
Do not update it, just wait for a few days, until they fix this
This is first time in my life, that I bought android phone, and that i didnt touched it, unlock it or root it, and with offical update i am having problems that i never had with custom roms
Click to expand...
Click to collapse
Mine was like yours . Ya I skipped the backup and thought it was a breath and it got stuck and tried to update it but every time the percentage increased so after so many times it did update... but it ended up wiping my phone .. no photos no nothing .... i guess looking for a good rooted rom is as good as any... this sucks
Can you guys suggest Lolipop roms which are rooted and as close as possible to stock rom ?
Help me pls if anyone has a solution pls
My Problem (I've looked for hours in the forum, but can't find anything similar to my situation):
Got my LG G2 (D802, 16GB, Android 4.4.2) today. I wanted android l on it, ( MADE IN KOREA BOUGHT IN UAE AND NOW I AM USING IT IN INDIA)
it got stuck while updating from pc suite as thei was a shortage of storage although i had more than 1gb of storage free.
I can't get out of the screen where it says "Firmware upgrade and 0%, und below is "B10" and "unrooted". When i press the power button for some seconds the screen gets black, then the LG logo appears and immediately the Firmware-upgrade-screen appears, again with "0%" and "B10" and "unrooted".
I also can't get into recovery mode: When it push volume down and power butten, and it asks me to do a factory hard reset and i press the power button to confirm (when normally then the recovery mode menu appears) it changes automatically again to the Firmware-upgrade-screen.
what to do to get my g2 back to life
pls help
Don't know if this works for anyone else but...
I got mine stuck on the firmware screen because I was holding the volume up button while it was booting up. So I removed it from the computer and took out the battery. Then I put it back in, booted into recovery mode and rebooted to bootloader. It went to the lock screen and I didn't lose anything.
Help
I have a similar problem, my phone is stuck on 0% Firmware update and says in a little box: 910K B100. I have tried powering off but it doesn't work. Please help.
Hi guys, so I recently have this problem where I try to turn on my phone and he starts to boot and at the part where the boot animation comes it shows only a blue screen for like 10-15 secs and then turns off. That happend after I was trying to disassemble the phone(long story), anyway I didn't completely disassemble it just took out the screws and then gave up and put the screws back. The blue screen happens only when I get the battery out and back, if I try to boot the phone after the blue screen it just gets to bootloop. Guys, please, I need very fast help because the phone isn't mine(Yes I know im stupid). Anyway thanks for reading this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
xgamer231 said:
Hi guys, so I recently have this problem where I try to turn on my phone and he starts to boot and at the part where the boot animation comes it shows only a blue screen for like 10-15 secs and then turns off. That happend after I was trying to disassemble the phone(long story), anyway I didn't completely disassemble it just took out the screws and then gave up and put the screws back. The blue screen happens only when I get the battery out and back, if I try to boot the phone after the blue screen it just gets to bootloop. Guys, please, I need very fast help because the phone isn't mine(Yes I know im stupid). Anyway thanks for reading this.
Click to expand...
Click to collapse
Google un brick Samsung j5
infixremix said:
Google un brick Samsung j5
Click to expand...
Click to collapse
I have already flashed a stock firmware and still the blue screen.
xgamer231 said:
I have already flashed a stock firmware and still the blue screen.
Click to expand...
Click to collapse
Damn... Try using another ROM. If you can get to the part where the boot logo should be but appears blue screen you migh have a chance...
Get into download mode and flash TWRP trough Odin and one of the custom ROMs around. If it boots into TWRP succesfully and after that it succesfully boots into the ROM you just installed trough TWRP, than it was a software issue. If it doesn't boot and you get the same exact blue screen... It might be either a hardware error or an issue with the bootloader. I'm really saying that because it is one of the more sensitive and important parts of the firmware and the fact that your blue screen color is exactly the same as the download mode (bootloader) might link it to an issue with a bootloader.
@Henkate, I'm summoning you. Maybe you an help this fella as I think you know loads more things about the firmware
BTW: next time don't mess with hardware. Messing with software is easier and safer : )
Also... What were you trying to do by taking the poor guy appart? Replacing the screen maybe? Stuck SIM card?
Amarius1 said:
Damn... Try using another ROM. If you can get to the part where the boot logo should be but appears blue screen you migh have a chance...
Get into download mode and flash TWRP trough Odin and one of the custom ROMs around. If it boots into TWRP succesfully and after that it succesfully boots into the ROM you just installed trough TWRP, than it was a software issue. If it doesn't boot and you get the same exact blue screen... It might be either a hardware error or an issue with the bootloader. I'm really saying that because it is one of the more sensitive and important parts of the firmware and the fact that your blue screen color is exactly the same as the download mode (bootloader) might link it to an issue with a bootloader.
@Henkate, I'm summoning you. Maybe you an help this fella as I think you know loads more things about the firmware
BTW: next time don't mess with hardware. Messing with software is easier and safer : )
Also... What were you trying to do by taking the poor guy appart? Replacing the screen maybe? Stuck SIM card?
Click to expand...
Click to collapse
Well I'll try a custom rom when I get come, but now I will tell you the whole story how it went trough. So when I got this phone it was stuck in a bootloop(it boots up, freezes for 5-10 secs and restarts and so on), and I tried hard reset and putting stock firmware and still nothing. I got to a conclusion, because the phone was drowned in water few days ago, maybe the power button had a short circuit so I went disassembling it to try to dry more the motherboard, when I took of the screws I realized I can't get to the mobo because I needed to get first the display off and I didn't had the tools for that. Anyway I put the screws back and boom blue screen.
The blue color isn't exactly the same like in download mode, the camera I took the picture with is very bad. The blue color is a standard blue blue(like in rgb).
I don't believe it couls be a hardware failure, because I didn't touch anything drastic, one thing I did touch was the display cable under the little panel, I just plug it off.
Btw. Just to mention its the J500FN model.
I really apprechiate the help guys :S
xgamer231 said:
Well I'll try a custom rom when I get come, but now I will tell you the whole story how it went trough. So when I got this phone it was stuck in a bootloop(it boots up, freezes for 5-10 secs and restarts and so on), and I tried hard reset and putting stock firmware and still nothing. I got to a conclusion, because the phone was drowned in water few days ago, maybe the power button had a short circuit so I went disassembling it to try to dry more the motherboard, when I took of the screws I realized I can't get to the mobo because I needed to get first the display off and I didn't had the tools for that. Anyway I put the screws back and boom blue screen.
The blue color isn't exactly the same like in download mode, the camera I took the picture with is very bad. The blue color is a standard blue blue(like in rgb).
I don't believe it couls be a hardware failure, because I didn't touch anything drastic, one thing I did touch was the display cable under the little panel, I just plug it off.
Btw. Just to mention its the J500FN model.
I really apprechiate the help guys :S
Click to expand...
Click to collapse
This looks like hardware failure. I would check the cable for the display you removed is properly connected.
If it is then it may be you've damaged the delicate connector.
ashyx said:
This looks like hardware failure. I would check the cable for the display you removed is properly connected.
If it is then it may be you've damaged the delicate connector.
Click to expand...
Click to collapse
The cable is in place, I don't really believe its the cable because bl and recovery are fine(no graphical disorders).
Just tried to flash TWRP, and I got a auth fail(google says i need to autorize something in dev settings idrk), strange thing I don't get the bootloop anymore when I try to turn on the phone after the blue screen shuts off.
Here's a video:
https://www.youtube.com/watch?v=tWkqTg77rbg
xgamer231 said:
The cable is in place, I don't really believe its the cable because bl and recovery are fine(no graphical disorders).
Just tried to flash TWRP, and I got a auth fail(google says i need to autorize something in dev settings idrk), strange thing I don't get the bootloop anymore when I try to turn on the phone after the blue screen shuts off.
Here's a video:
Click to expand...
Click to collapse
Bro, why don't you go to service somewhere in your city, im sure they wouldn't take much money for that fix since i believe it is minor hardware failure, they have appropriate tools and will get the job done quickly. Don't mess with your phone further more. I know this is not the answer you exoected but this is what i would do since i would rather give up on 20$ and be safe.
xgamer231 said:
The cable is in place, I don't really believe its the cable because bl and recovery are fine(no graphical disorders).
Just tried to flash TWRP, and I got a auth fail(google says i need to autorize something in dev settings idrk), strange thing I don't get the bootloop anymore when I try to turn on the phone after the blue screen shuts off.
Here's a video:
Click to expand...
Click to collapse
But can you enter Recovery? If yes, you can transfer a rom zip file from your computer to phone as adb is working in TWRP. If after flashing the ROM you still get the blue screen... Than it definetelly isn't a software issue, but a hardware one, persisting no matter what you do to the software.
Amarius1 said:
Damn... Try using another ROM. If you can get to the part where the boot logo should be but appears blue screen you migh have a chance...
Get into download mode and flash TWRP trough Odin and one of the custom ROMs around. If it boots into TWRP succesfully and after that it succesfully boots into the ROM you just installed trough TWRP, than it was a software issue. If it doesn't boot and you get the same exact blue screen... It might be either a hardware error or an issue with the bootloader. I'm really saying that because it is one of the more sensitive and important parts of the firmware and the fact that your blue screen color is exactly the same as the download mode (bootloader) might link it to an issue with a bootloader.
@Henkate, I'm summoning you. Maybe you an help this fella as I think you know loads more things about the firmware
BTW: next time don't mess with hardware. Messing with software is easier and safer : )
Also... What were you trying to do by taking the poor guy appart? Replacing the screen maybe? Stuck SIM card?
Click to expand...
Click to collapse
Amarius1 said:
But can you enter Recovery? If yes, you can transfer a rom zip file from your computer to phone as adb is working in TWRP. If after flashing the ROM you still get the blue screen... Than it definetelly isn't a software issue, but a hardware one, persisting no matter what you do to the software.
Click to expand...
Click to collapse
Yea, but I don't have TWRP installed because odin gives me some auth fail. I don't really know to give up or continue with this.
xgamer231 said:
Yea, but I don't have TWRP installed because odin gives me some auth fail. I don't really know to give up or continue with this.
Click to expand...
Click to collapse
It's possible you have damaged the emmc. The bootloader resides on a different part of memory to the rest of the firmware.
However, can you actually boot to stock recovery?
ashyx said:
It's possible you have damaged the emmc. The bootloader resides on a different part of memory to the rest of the firmware.
However, can you actually boot to stock recovery?
Click to expand...
Click to collapse
Yes, everything exept the bot sequence is fine.
Have you tried factory reset in recovery?
It looks for GPU failure, not a software.
Anyway, it happened after disassembly, before as I suppose everything was working so dissamblessing was the most probably cause of this.
As a mate mentioned, go to a service center, they should agree with my opinion. Unfortunately mainboard switch would fix it.
Wysłane z mojego Nexus 5X przy użyciu Tapatalka
xgamer231 said:
Yea, but I don't have TWRP installed because odin gives me some auth fail. I don't really know to give up or continue with this.
Click to expand...
Click to collapse
Right what I suggest you do is re install stock from Odin then download NICK VERSES twrp install that and then install a ROM either RR or cm 13 if that doesn't work take it to a store
infixremix said:
Right what I suggest you do is re install stock from Odin then download NICK VERSES twrp install that and then install a ROM either RR or cm 13 if that doesn't work take it to a store
Click to expand...
Click to collapse
He cant flash anything custom as he can't enable OEM unlock.
ashyx said:
He cant flash anything custom as he can't enable OEM unlock.
Click to expand...
Click to collapse
Ffs take it to a shop then
---------- Post added at 01:50 AM ---------- Previous post was at 01:39 AM ----------
xgamer231 said:
I have already flashed a stock firmware and still the blue screen.
Click to expand...
Click to collapse
http://www.any-data-recovery.com/an...e-blue-screen-of-death-on-samsung-galaxy.html it seems to be a software issue
Okay looks like we're out of solutions, I'll take the phone back to his owner and explain the situation.
Thank you all guys, I really apprechiate the help
Same problem
Got the same problem with my friends device 3 days ago
What should i do i haven't try anything yet but thinking to re assembly it
Hello, i know this threat is very old, but recently i sufer the same problem (Yes i dissambled the phone). My problem was worst because eventually my phone wasn't booting at all. So heres what i do:
1. I took the battery out.
2. I plug in the charger until the phone gets a bit hot.
3. Then (with the charger still plugged) i put the battery back.
4. After that i get the charging screen, so i press the power on button and the phone booting on normally.
Note: While i was doing that process the phone was without the back part (i mean the part where the speaker is) and i reassembled the phone while it was on.
I Hope this help someone!!!!
I've searched far and wide for an answer to my problem and I've returned with nothing. It's been almost 24 hours without my phone and I think I'm losing it. I've downloaded and tried LGUP (alongside Uppercut), LG FlashTool 2014, LG Bridge, LG DLLs, etc and nothing has worked to flash my phone to stock with the KDZ. The closest I've gotten it to work is with LGUP but stupid me, I managed to edit the buildprop before it went self destruct and changed the device identifier to a Google Pixel XL and LGUP refuses to cooperate. Any help is appreciated. Please. :good:
I've managed to get into fastboot. I'm sure I can do something from here but idk what to put. Any help is appreciated once again
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
kilakoust said:
I've searched far and wide for an answer to my problem and I've returned with nothing. It's been almost 24 hours without my phone and I think I'm losing it. I've downloaded and tried LGUP (alongside Uppercut), LG FlashTool 2014, LG Bridge, LG DLLs, etc and nothing has worked to flash my phone to stock with the KDZ. The closest I've gotten it to work is with LGUP but stupid me, I managed to edit the buildprop before it went self destruct and changed the device identifier to a Google Pixel XL and LGUP refuses to cooperate. Any help is appreciated. Please. :good:
I've managed to get into fastboot. I'm sure I can do something from here but idk what to put. Any help is appreciated once again
Click to expand...
Click to collapse
My guess is that you're rooted considering you've edited the build.prop? Why not enter recovery and flash a stock rom?
kilakoust said:
I've searched far and wide for an answer to my problem and I've returned with nothing. It's been almost 24 hours without my phone and I think I'm losing it. I've downloaded and tried LGUP (alongside Uppercut), LG FlashTool 2014, LG Bridge, LG DLLs, etc and nothing has worked to flash my phone to stock with the KDZ. The closest I've gotten it to work is with LGUP but stupid me, I managed to edit the buildprop before it went self destruct and changed the device identifier to a Google Pixel XL and LGUP refuses to cooperate. Any help is appreciated. Please. :good:
I've managed to get into fastboot. I'm sure I can do something from here but idk what to put. Any help is appreciated once again
Click to expand...
Click to collapse
Can you not get into TWRP?? I believe its the same way as everyone else..\
Hold the volume down button and the power button and as soon as you see the LG logo left go of the power button and press it again. This manual step is a pain in the arse, but it will get you there eventually. Since youre rooted, you also get the "This device is corrupted screen" yes? The LG logo popup you are looking for is right before that.
What I do for easy and fast access is this. I keep the back cover off and hold the volume down button for ease. I hold the power button, let go, and press it again and ususally that first try doesnt work. As soon as I see the corrupt screen I take the battery out very quickly and put it back in and repeat the process. After a few tries the LG logo will hang before the corrupt screen and that gives you the time you need to let go of the power button and then hold it again until the factory reset screen comes up. Just hit yes twice... It will go into TWRP.
Biff627 said:
Can you not get into TWRP?? I believe its the same way as everyone else..\
Hold the volume down button and the power button and as soon as you see the LG logo left go of the power button and press it again. This manual step is a pain in the arse, but it will get you there eventually. Since youre rooted, you also get the "This device is corrupted screen" yes? The LG logo popup you are looking for is right before that.
What I do for easy and fast access is this. I keep the back cover off and hold the volume down button for ease. I hold the power button, let go, and press it again and ususally that first try doesnt work. As soon as I see the corrupt screen I take the battery out very quickly and put it back in and repeat the process. After a few tries the LG logo will hang before the corrupt screen and that gives you the time you need to let go of the power button and then hold it again until the factory reset screen comes up. Just hit yes twice... It will go into TWRP.
Click to expand...
Click to collapse
Wow a yeah later and this helped me. my superv20 mod took a poop for no reason at all and i couldn't boot or get into recovery for what ever reason but this key combo if done twice worked to get me into recovery.
cbissa18 said:
Wow a yeah later and this helped me. my superv20 mod took a poop for no reason at all and i couldn't boot or get into recovery for what ever reason but this key combo if done twice worked to get me into recovery.
Click to expand...
Click to collapse
I'm glad that this helped you out. Getting into recovery with root was always a pain.
Biff627 said:
I'm glad that this helped you out. Getting into recovery with root was always a pain.
Click to expand...
Click to collapse
yeah not sure why, its like it doesnt stick smh. but it does you just have to toy with it....
cbissa18 said:
yeah not sure why, its like it doesnt stick smh. but it does you just have to toy with it....
Click to expand...
Click to collapse
Well with the corrupt screen, it seems that the time frame that would allow you into Recover/TWRP is shorted. So pulling the battery after trying usually gave me more than enough time to boot into it. Probably not the best for the phone though xD