i was spl1.04 orginal and i upgraded hard spl7,
however i've check by mtty that i'm not sure supper CID yet, so i follow here instruction to become supper CID but fail.
I've download the file and put sspl in herm200 and run autoupdate, it prompt load fail.
But result i've got my spl become spl1.40olipro ???
i am just confuse that what spl i am. Do i still hard spl? if i want upgrade to hard spl 7 , do i need to back to spl mfg ->spl 1.04 ->hard spl 7?
can i spl1.40olipro->hard spl 7?
SSPL was probably your misstep.
At this point just re-flash the latest Hard-SPL and you should be fine. You'll have SPL 2.10.Olipro also be "SuperCID" without actually changing your CID.
THEN, quit hacking around and do some reading before you make your next move.
thanks that i am back to hard spl 7 now.
i have completed hard spl, my ipl/spl is 2.2.0001 and 2.21 olip
please help
Download 'Mun RUU' from the HardSPL thread and replace this RomUpdateUtility with the RUU in the Rom you are trying to flash,it'll work.
I've got the same problem, where can i find 'Mun RUU'?
Solved...
Im tryin' to use HARD-SPL-V7
Its asking me my actual spl version
How do i do to know my spl version?
anybody let me know please
use SSPL (unsafe) to flash hard SPL. It is actually Soft SPL. It is removed once you have Hard SPL installed.
Cheers...
I am trying to do the HardSPL upgrade on an orange spv m3100 as per http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26 I have the lates version of WMDC running on windows vist and can sync etc no problem
When i go through the process it shows current image as 1.23.61.4 When i carry on in brings upenter bl.exe on the phone. The phone then goes into the bootloader screen and the WMDC shows disconnected
The programme hows verifying the information on your hermes Then I get error 260 update error cant connect
The current bootloader says.
HERM100
1PL-SSPL by Des
HERM100
SPL-1.09.ds
Any ideas and help would be grately appreciated
thanks in advance....steve
Plz help
my phone shows following details
SPL-1.09.ds
when i upgrade to HardSPL 2.60, it does upgarde but when after restarting it again shows the same version of SPL
i am now unable to soft reset my phone
and one more problem i am facing is that my phone shows HERM200while before this problem it was HERM100
this problem arose after i tried to downgrade to MFG bootloader
before that i had SPL 2.30
plz help
fcwdadmin, as you have sspl.exe already running (known as soft SPL - 1.09 des) format 2Gb or less sd card FAT32, put the .nbh file of Hard SPL V7 on and rename to hermimg.nbh . Reset to bootloader - hold power, ok button above flywheel and reset with stylus. Follow the prompts. This should put Hard SPL V7 on your phone. ONLY DO THIS IF YOU HAVE Soft SPL INSTALLED...
Go to bootloader to check, it should read IPL - 1.04 and SPL - 2.10 oli.
You should now be able to put any rom on from the Hermes section. I recommend using the sd card method for that too.
Cheers...
the bootloader says:
HERM100
IPL-1.01
HERM100
SPL-1.04
Is that the same thing again ??
Many thanks in advance
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
ultramag69 said:
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
Click to expand...
Click to collapse
I've been trying to find help with this everywhere, but none of the steps seem to work for me. Should I consider the phone brick now cuz I can't get Hard SPL v7 on? I was able to go up to 1.40 using CID unlocker, but have been stuck since then.
Can you get the Hermes back into today screen?
ultramag69 said:
Can you get the Hermes back into today screen?
Click to expand...
Click to collapse
No brick. I was able to get to SPL 1.40 and have been able to flash other ROMs. I've just read too many posts that says v7 is the way to go for stability sake.
Download Hard SPL V7 from the Hard SPL thread, go to page 116, post 1160 of the same thread for instructions on how to install using the sd card. YOU NEED TO FOLLOW THESE STEPS EXACTLY... One thing wrong & it won't work.
Afterwards, you can use these steps, dropping the steps using SSPL.exe (Soft SPL) to install roms. I find it much easier & safer than using the pc.
Cheers...
Hi all,
I want change my ROM from ESP to an ITA rom (HTC Touch2), then I'm first installing olinex Hard SPL.
I'm trying with olinex spl 1.40; 1.93; but the pda freeze at 0% of upgrade progress bar, without progress.
I've done same operation in other device, like Diamond, without any problem...
fabdan said:
Hi all,
I want change my ROM from ESP to an ITA rom (HTC Touch2), then I'm first installing olinex Hard SPL.
I'm trying with olinex spl 1.40; 1.93; but the pda freeze at 0% of upgrade progress bar, without progress.
I've done same operation in other device, like Diamond, without any problem...
Click to expand...
Click to collapse
Be careful. HSPL 1.40 & 1.93 are specific for Diamond. Can't use for Touch2.
You have to wait until the issue of an HSPL for Touch2 otherwise you can use a goldcard buying Qmat.
Hard SPL can`t in each one of the PDA phone.