Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

No GSM message on HTC Advantage 7500

Dear friends :
today i see that my unit is crashed and it didn't work , just an still today screen with no response to anything.
I did a soft reset ,but after a soft reset , it just the first time , a crashed today screen .
Then I did a hard reset and on first boot screen with HTC logo appear " No GSM " and when my unit boot , no GSM services is available.
then I go to a ROM upgrade with original ROM and the same rom that installed on my device , but at 12% of process a " Communication Error " has been shown on the PC .
I try to recover the error , but one more time the update process stoped at 12% and now when I Turn my unit on , just a three color screen and nothing else .
please help me that what can I have to do for this problem .
thank you .

Anybody can Help me ?

Are you trying to update on a PC running Vista?
Have you tried AP3?

No I do an Upgrade with windows XP SP2
I didn't try AP3 , because I can't do a Hard SPL ! my unit didn't unlock with HARD SPL softwares .
Many thanks for your answers

Did you try the s/ware form here http://forum.xda-developers.com/showthread.php?t=316846 ?

dear Confucious
Yes I test this software , but it didn't unlock my phone , now my unit didn't have IMEI ! code on device information .

Htc p3400 hanged at start up page onyl

Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.

hard reset
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
do hard reset

i had done hard reset also

Try to bootup without the SD card (and may be SIM), I had this problem with my Vox, the SD Card was corrupted. After formatting the SD Card, everythig became normal.
Best of Luck

Same problem
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says Setup complete, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos (from Portugal)

matosmatos said:
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says congratulations, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos
Click to expand...
Click to collapse
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!

i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks

for ur info @matosmatos
hi
as per the numbers quoted by u urs is a old gene so falsh roms for old gene only this is just for ur info
goodluck
matosmatos said:
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
Click to expand...
Click to collapse

@smb_do
hi
assuming ur phone is just dead ie just blank screen do this
1.power off the phone remove batter and press the power button 3 secs
2.put batter back in to the phone
3.Press camera button and then power on at the same time u will get tricolor
used usb and Flash new ROM
or press camera button and do soft reset using stylus this will also give u the tricolor use USB and flash new ROM
goodluck
smb_do said:
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
Click to expand...
Click to collapse

thasnffffffffff

Im so so saaaad
I try avery thing hard reset , now roms every time it accept the now rom and whine it restsrts again tha same problem it stop at
ONPL 1.07.0000
SPL 1.07.oref
GSM 02.79.90
OS 1.9.1.1
please help me send me at
ahmedrefaat82/hotmaill.com

gene hanges at start up page onyl (after rom Upgade)
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs

satishgosavi said:
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
Click to expand...
Click to collapse
Not likely, try a hard reset and see if your issue is solved

Addicted2xda said:
Not likely, try a hard reset and see if your issue is solved
Click to expand...
Click to collapse
I had tried that also but not able to recover I had to burn the ROM again .
I am scared now to soft reset my gene. Never know when it will get hanged again. (pls note that it does not hang on every soft reset).
I liked the new ROM (6.1 pro Sumeet) so much. It is fast and have left enough room to add/execute other applications. I have read so many good comments about the ROM. I do not want to change it to any other version.
Please.. please try to get some solution.
Thanks in advance.
regards
Satish

It Worked
Thanxxxxxxxx

Skin Is Not Loaded :(

hi my friends.
I changed my jasjar's tomal 6.1 rom to Original WM5 for sell my phone
but after changing rom, i have a terrible problem.
when i closed the battery for change the simcard and turn it on. when the windows logo appears a blue screen showed and the gsm led begin to work (blinker).
after several soft resets the windows starts and ready to work but when i press the power button to standby the device (sometimes) for turn on the device (after standby) the screen didn't appear.!!
i'm very upset
after that i flashing the radio to newer version (1.18) and flash back to WM6.1 TOmal , WM6 , ... but i still have this problem.
in the tomal's wm6.1 rom (TML_v82_WM61_19960) before the problem shown an error appears under the windows logo > The Skin Is Not Loaded < and after that a black or blue screen appears and nothing...
please help me to fix it.
thanks friends

No Answer ?!
Really ?!
it's very important for me.
plz help

Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.

-Jonny- said:
Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.
Click to expand...
Click to collapse
What is the mtty ? doc-format ?
How can i do it ?
tnx for attention

DOC format

-Jonny- said:
DOC format
Click to expand...
Click to collapse
wow , thanks for guide me.
as your experiences , this work would be harmful for the device ?
thankx

It's not harmful - basically it totally wipes the device removing everything (including garbage). So you will, of course, need to flash a ROM afterwards.

[Q] dead device

Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!

rupesh baviskar said:
Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!
Click to expand...
Click to collapse
hi
if u can get ur tricolor screen then try this
connect the usb cable to pc and see if u get the USB words on the phone tricolor screen if so good try flashing any official ROM the same happened to my phone long back did the above got my phone back asuming u have done HSPL for ur phone if u have not done that then the only way is to take it to service
hope it helps good luck
thanks
hari

Wrong forum.. Touch P3450 is not a touch 3g , its the original touch (ELF version)
but i will try and help as i have owned both.
if your hardware buttons are not working it could be possible that your send and end keys are stuck down as this key combo brings up the hard reset you are talking about.
think you are going to have to open it as it sounds like a hardware fault, and if you cannot get into bootloader you cannot flash
if it was working alright before this is not the case, but either way you will have to fix your camera button and get into bootloader