can I upgrage rom via bluetooth? - Touch GSM General

Dear all, my elf now can't activesync via USB.
I'd use the white screen method to flash downward to original rom, problems still there.
I'm sure the USB port had problems now.
The problems is... although I can connect activesync via bluetooth.
but I can flash rom via bluetooth.
the original come with origianl IPL 1.15 and HSPL 1.15
which I can't use the wihte screen method.
I had try install the EnableRapi.Cab & Cert_SPC.Cab,
after elf tune to white screen, my pc popup connection error message.
then fail in flash rom.
Could anyone can help me to solve it?
I checked with the tech. support. it cost me US$50 for repair...
this nearly the 2nd hand price of elf.
Please help.

If your PC can't detect your phone over USB, then you can't use the white screen method. Flashing over bluetooth is impossible, so that's out of the question.
The only way I can think of to fix the problem is by flashing from a Micro SD card. To flash from Micro SD, format the card as FAT16, copy the .nbh file you want to flash to the root of the card, and rename the .nbh file to "ELF0IMG.nbh", without the quotes. Turn off your phone, and enter the tri-color boot screen by turning the phone back on again while holding the camera button. The .nbh file should start flashing right away.
You'll need to flash either HSPL or USPL before flashing any ROMs - I'd recommend HSPL, as it's easier to use. If you forget to flash HSPL or USPL first, then YOU WILL BRICK YOUR PHONE. Good luck.

try with disable usb port fast speed first. If don't work you can create a goldcard and flash rom with goldcard sd (see goldcard thread in this forum).

thanks.
for method 1.
use "ELF0IMG.nbh" and hold down the camera key and reset.
I used before at 1.17 HSPL USPL or upper.
it doesn't work on the original 1.15 HSPL USPL.
for method 2.
goldcard sd
in the instruction MTTY,
it stated "connect the Elf via USB to ActiveSync"
So, I still can flash my elf at 1.15 HSPL and USPL.
I'm very stupid to flash back the original rom.
Seem I need to pay US$50 for this dumb thing.
btw... thanks a lot

Related

Flashing rom uspl and no image file

Hi All,
I have tried searching for the answer to this question and cannot find it, though I am sure I wont be the first to have had this problem.
I am trying to flash a new rom on my touch HD, have tried two different ones - duttys and black pearl. I have managed to get the upsl to work in the bootloader but i cannot get a rom to boot from the SD card. I have followed the instructions on the pages with the roms (same in each) and all i see is a screen flash up after running uspl saying "no image file" then it goes back to the bootloader screen.
In order to get out of bootloader I have to remove my battery which i assume is normal and then it goes back to the normal spl.
I am pulling my hair out on this one - and I dont have much to pull on!
I didnt think it would be so hard with all of the instructions about!
What want you do?
What stage has you done?
I wanted to load duttys rom using upsl but unfortunately I couldnt get it to work so I used the program that comes with the rom to load it in without using bootloader.
I had to load on Olinex to make it work
I had a similar thing the other day when I was having a blonde moment. Renamed the image file BLACIMG.nbh, instead of just BLACIMG......so the actual file name when I looked in to it was actually sitting as BLACIMG.nbh.nbh
Once I'd deleted the .nbh extension out of the file name I renamed it worked.
deafpotato said:
Hi All,
I have tried searching for the answer to this question and cannot find it, though I am sure I wont be the first to have had this problem.
I am trying to flash a new rom on my touch HD, have tried two different ones - duttys and black pearl. I have managed to get the upsl to work in the bootloader but i cannot get a rom to boot from the SD card. I have followed the instructions on the pages with the roms (same in each) and all i see is a screen flash up after running uspl saying "no image file" then it goes back to the bootloader screen.
In order to get out of bootloader I have to remove my battery which i assume is normal and then it goes back to the normal spl.
I am pulling my hair out on this one - and I dont have much to pull on!
I didnt think it would be so hard with all of the instructions about!
Click to expand...
Click to collapse
Did you remove storage card before entering Bootloader screen? Put storage card in after Bootloader is up and before opening USPL.
USPL HowTo
Sorry to ask again.
I had the same problems.
As I couldn't do with USPL (just did not find reasonable step-by-step instructions), I used OliNex HardSPL which worked fine.
But now with new ROM updates, I face significant problems with display color and radio not working.
So, I actually definitely need and would like to ask somebody to take the time to post ...
step-by-step instructions on how to use USPL
PLEASE !
USPL HowTo
Obviously, I just missed out one point and needed to change another.
But for those in the same situation:
Probably only works on Windows XP, didn't work on my Vista PC.
(1) Download the latest USPL (currently 2.5)
(2) extract anywhere on your computer
(3) Go to ActiveSync properties and disable "Allow USB Connections" option
(4) Turn off your device (long press "Power" key or remove/replace battery)
(5) then enter SPL bootloader mode (tri-color)
- Blackstone: when device turned off by pressing and holding "VolDown" key plus "Soft Reset" simultaneously
- did NOT work for me: by pressing and holding "Power" and "VolDown" keys simultaneously.
(6) Connect USB cable and make sure "USB" label appeared in the white portion of the screen on your device.
(7) start / run "cmd" (DOS console) on your desktop PC
(8) Execute blac_uspl.exe in DOS window
current status and any error messages USPL encounters will be displayed in the console window.
(9) If everything goes well, your device will restart and SPL version label should read "1.15.USPL" indicating that USPL was loaded successfully.
You ever read through the USPL thread?
stepw said:
10. How to use it?
Download the latest USPL attached to the second post of this thread and extract anywhere on your computer.
Go to ActiveSync properties and disable "Allow USB Connections" option. Turn off your device (long press "Power" key or remove/replace battery), then enter SPL bootloader mode (tri-color) by pressing and holding "Power" and "VolDown" keys simultaneously.
Connect USB cable and make sure "USB" label appeared in the white portion of the screen on your device.
Execute blac_uspl.exe; current status and any error messages USPL encounters will be displayed in the console window.
If everything goes well, your device will restart and SPL version label should read "1.14.USPL" indicating that USPL was loaded successfully.
If SPL version does not include "USPL" or if the screen is black, soft reset and try again. If "USB" label disappeared and did not reappear, reinsert USB cable.
You can then start RUU update to flash RUU_signed.nbh. Once RUU update is completed, device will restart using regular flashed SPL.
If you want to flash from SD card instead, make sure your SD card is not inserted when you enter the bootloader originally.
SPL will try to install it and would fail if blacimg.nbh is not signed by HTC. Insert the card after "USB" label comes up in SPL but before running USPL.
You can run "blac_uspl.exe ?" to get command line parameter help. Only 1 parameter is accepted and that is the name of an SPL file you want to load. You can load an MFG SPL or HSPL. USPL automatically takes care of allowing unsigned/cooked ROM flashing with any SPL you use.
Click to expand...
Click to collapse
Should be just clear, isn't it? Have used it a few times, without any problems ...
No, it probably wasn't clear enough.
At least it didn't work for me.
see the changes I applied above (plus minor additions)
remove the memroy card!
the first time i tried the upgrade, it failed... because my memory card was inside the phone. worse, the mem card contains the rom upgrade file.
pls remove the memory card first.. then run the ruu update.
after which, it will state that rom is 1.15.
then can insert memory card (only if u see the USB word on your phone)
then can re-run program.. and update firmware..
I have experienced this problem where no image file was found when flashing from UPSL. I think this is some kind of random **** that happens. I have flashed countless ROM with this method and sometimes this **** just happens without any reason.
hi, how come my tri-color bootloader only shown "Serial" in the white portion of the screen? Is there something wrong with my HTC HD phone? I try to reflash the ROM thru this way since ActiveSync cannot detect my HD. My HD phone only shown battery charging whenever I plugged in the mini-USB cable into the computer.
Anyone can enlighten my issues? Thank you in advance!
I met the same issue, and I solved it by re-formatting the card using FAT32.
MOD EDIT
I'm closing this thread as dummies guide, USPL & HSPL threads already exist.
If your having still having difficulties post your query into relevant thread. I'd suggest you start with dummies flashing guide thread.
Thread closed

Unable to downgrade my SPL from 3.13 to 2.20

Hi there,
Hope you can help me...
Since i bought my Cruise, I flashed it to the newest ROM version of HTC and it automatically installed SPL 3.13 with.
The problem is that if I want to install the WM 6.5 rom, I have to "Downgrade" My SPL version from 3.13.0000 to 2.20.
I followed the steps explained by "Olipro", but when the upgrade starts, RUU kills activesync (seems to be normal) and when the phone normally reboots in bootloader mode (like when you flash a new rom), nothing happens. The phone didn't shutdown and tries to establish a new USB connection !
I tried to turn manually the phone in bootloader mode on to force the SPL update, but the % bar stays at 0 and RUU returns a communication error (262).
I tried also to install the wm 6.5 rom without install SPL 2.2, but it crashes (stays @ 0% too)
I don't know how to install this stinky version of HARD SPL.
Heeeellllpppp !!
NOTE : I tried with or without µSd, does the same thing.
Thx
hmm try disabling firewall and antivirus one of them may be blocking the connection. Thats my only thought about it.
Thank you for the answer but it don't work...
Nobody can help me ?
Try to extract the files from the newest htc rom to a new folder, and then copy the "RUU_Signed.nbh" from the SPL V2 folder to the extracted files (to the new folder) and run the "ROMUpdateUtility.exe" from the extracted files (from the new folder).
nope ...
Please, consider my asks...
I know there is necessarily a solution but I have not yet found.
I don't know where/why it is crashing.
What does the HTC need to downgrade the hardspl ?
Is there a protection that can't be bypassed with the 3.13 ?
The only thing that I can do atm, is flashing the official HTC rom (useless ^^).
The actual version of my rom is :
_HTC Touch Cruise_RUU_Polaris_HTC_FRA_3.13.406.0_radio_sign_25.85.30.07_1.59.42.15_Ship
Thanking you in advance...
Pixel69 said:
Please, consider my asks...
I know there is necessarily a solution but I have not yet found.
I don't know where/why it is crashing.
What does the HTC need to downgrade the hardspl ?
Is there a protection that can't be bypassed with the 3.13 ?
The only thing that I can do atm, is flashing the official HTC rom (useless ^^).
The actual version of my rom is :
_HTC Touch Cruise_RUU_Polaris_HTC_FRA_3.13.406.0_radio_sign_25.85.30.07_1.59.42.15_Ship
Thanking you in advance...
Click to expand...
Click to collapse
HSPL 3.13? In this ROM is ver. 3.13 drivers, not HSPL... If you have original ROM and you dont install Olipros HPSL, you have original HTC SPL...
When I enter bootloader mode, the HSPL version is : 3.13.0000
Of course it's the original htc HSPL.
The problem is that I can't downgrade it to the olipro's version : 2.20.
Did you try it on other PC?
2 PCs, 2 USB cables..
The official rom upgrade works fine, I dont think that the problem comes from the computer.
definite guide:
1. establish a connection with activesync via usb (orbit2 to pc)
2. start the romupdateutility provided in hardspl folder.
3. before it starts flashing, you need to also follow on-screen instructions on orbit2!!! execute jump-spl and stuff: click yes on orbit2!!
4. when the orbit2 states: Replug USB. you need to plug the usb-cable once off and then put it back to connect to your pc.
5. it starts flashing and restarts after its done.
Hi Manaaa,
I don't know what is jumpslp ??
I found it on the web (xda..), copied it in my "my documents" folder, ran it but it asks me a jump address (default is 0x00000000) and an spl (*nb) file..
What is jump spl ? What is the address to jump to? and where can I find the *nb file ?
In the olipro's hspl folder is only a *nbh file.
Thank you
I wouldn't recommend using a jump spl for our phones if there isn't one in the Hardspl Pack then one is not needed to be run.
Personally im still really confused by this so if i get it straight.
You are synced with activesync.
Run the file for Hardspl Run RomUpdateUtility.exe
Then go though. It switches off activesync.
Then what?? Exactly Does it ask you to replug the cable? Do you get the rom flash screen (with %) at all??
Also i dont think that spl flashes can be run from the booloader as it has to be a modded bootloader (jumpspl if you will), loaded by the program to be able to flash the new hardspl.
Also i know very little on this, this is as much as i understand it to be.
chris10230 said:
You are synced with activesync. OK
Run the file for Hardspl Run RomUpdateUtility.exe OK
Then go though. It switches off activesync. OK
Then what?? Exactly Does it ask you to replug the cable? NO
Do you get the rom flash screen (with %) at all?? NO
Click to expand...
Click to collapse
Normally, after killing activesync, the phone turns into bootloader mode. Mine stays in winCE and tries to establish new usb connection...
I also decided to force manually bootloader mode and killing activesync by myself.
I ran RUU again, it first checked the phone state (such as battery >50%, connectivity...)
CHECK : OK
Next step, by clicking "NEXT" on the RUU interface, the phone turns in "% mode" and the update starts but stays at 0%.
After a while, RUU returns an update error (such as 262).
Noway to flash hardSPL :'-( , v3.13 seems to be "write protected".
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
Click to expand...
Click to collapse
That is what error 262 is but really dont see why this happens either. And since you can boot into windows its not much help.
So it just wont go to flash it when you click it through, hmm
Your last resort would be to PM cmonex as she will have helped make this with oilpro. Ask and see if she can shed some light on this one. Maybe something has gone wrong somewhere (quite likely) that we don't know how to fix.
Stupid question but have you tried downloading, unzipping it again? May have been a bad dl... or unzip
Have tested it with about 10# DLs...
I PM'd Olipro, waiting for a response now
Flash back to HardSPL and don't Re-Plug
Hi Pixel,
Herewith are guide for you
1) Flash back to HardSPL and don't re-plug until end of session (5 minutes)
2) Flash back to original SPL 3.13 on this post . This original SPL for HTC Touch Cruise only
3) After you do this you cannot flash with other Cooked ROM or Shipped ROM
with different ID, unless you flash back to HardSPL
Good Luck my friend
I have exactely in the same configuration as Pixel69 with the same result.
I've tried to an other PC without any change.
Has somebody any idea?
Just had an idea what OS are you running to do it?
If its not 7 may not be fully compatible... Shot in the dark really

Please HELP ME!

i use cable flashed RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship.exe today(there are LEOIMG of the rom in TF CARD aswell)
then my HSPL hd2 screen shows a big "!" only can assess to the 3colour screen cant flash any roms. use card flash screem shows "NOT ALLOW 0028002"
PLEASE help me to fix it! thanks
what spl
so what spl does it show when at the tricolor boot screen? if it is 1.42.000 you should try flashing the hspl again. if you have hspl then try and flash from the boot screen using the custom ruu. if all else fails try flashing the stock rom from the region your phone came from.
This happened to me. This is how I fixed it.
leohd2 said:
i use cable flashed RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship.exe today(there are LEOIMG of the rom in TF CARD aswell)
then my HSPL hd2 screen shows a big "!" only can assess to the 3colour screen cant flash any roms. use card flash screem shows "NOT ALLOW 0028002"
PLEASE help me to fix it! thanks
Click to expand...
Click to collapse
This happened to me the other day. the error you see means you used the wrong shipped ROM to flash your device... I was stuck with an HD2 that would'nt boot and showed the big "!" as well. since I could still access the bootloader, all i did was the following:
1.find right shipped ROM,
2.extracted ruu_signed.nbh
3.reformat microsd card to fat32
4.copy .nbh file to storage card root
5.rename .nbh file to LEOIMG.nbh
6.hopefully you have more than 50% of your battery left so you can flash via microsd method (did not try flashing via cable again, but it could work as well)
7.I'm sure you know that to flash using microsd method means you need to hold VOL Down key while Pressing Power.
8.wait for update to complete (if its the right Shipped version it will flash till updated)
9.reboot and dance!
optional steps:
10.Hard Reset Shipped ROM
11.Run HSPL again
12.Flash till you "almost" brick it then repeat from step 1... =)
Happy Flashing!
leohd2 said:
i use cable flashed RUU_Leo_hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship.exe today(there are LEOIMG of the rom in TF CARD aswell)
then my HSPL hd2 screen shows a big "!" only can assess to the 3colour screen cant flash any roms. use card flash screem shows "NOT ALLOW 0028002"
PLEASE help me to fix it! thanks
Click to expand...
Click to collapse
Just install the HSPL via USB and then you can flash whichever Shipped ROM or Cooked ROM you want.....
Remember hard reset after flashing ROM

Struggling to downgrade WP7, Please help!!!

I'm trying reinstall WM6.5 on my HTC HD2 from MAGLDR V1.13.
I've downloaded the stock rom from HTC website and im trying run the installer but it fails it cant seem to pick up my phone as a USB connection.
I tried the bootloader way but it always get stuck at the installation part at 0%.
what am i? doing wrong, its driving me mad..
SPL version is SPL-2.08.0000
Make sure you’ve got more than 50% power on the device.
• Unplug USB cable
• Power Off device.
• Press and hold volume down button and press power button to start again.
• You will be presented with a tricolor splash screen.
• Connect USB cable to PC
• On the Tricolor splash screen you see “serial”; change to “usb”, if not unplug and plug the cable back in.
• As Administrator Run the WM6.5 ROM Update and follow instructions, your device should now be flashed with WM6.5.
GreatLorens said:
Make sure you’ve got more than 50% power on the device.
• Unplug USB cable
• Power Off device.
• Press and hold volume down button and press power button to start again.
• You will be presented with a tricolor splash screen.
• Connect USB cable to PC
• On the Tricolor splash screen you see “serial”; change to “usb”, if not unplug and plug the cable back in.
• As Administrator Run the WM6.5 ROM Update and follow instructions, your device should now be flashed with WM6.5.
Click to expand...
Click to collapse
thanks for the reply,
done the above a few times but no joy..
I see USB at the bootloader and when i run the ROM update, it doesnt show me what the current version of the phone is but just says it will update to the version 3.14.110.1! so when i start the install process nothing happens, i get the error [302]..
why is that?
any other way to flash this??
rafter_01 said:
thanks for the reply,
done the above a few times but no joy..
I see USB at the bootloader and when i run the ROM update, it doesnt show me what the current version of the phone is but just says it will update to the version 3.14.110.1! so when i start the install process nothing happens, i get the error [302]..
why is that?
any other way to flash this??
Click to expand...
Click to collapse
i had came across this issue last week.
when in tri-color mode, re-install hspl 2.08 and then magldr 1.12/1.13.
then try installing wm6.5.
This worked in my case.
Check if it does in urs too...
Al the best...
ankushmulay said:
i had came across this issue last week.
when in tri-color mode, re-install hspl 2.08 and then magldr 1.12/1.13.
then try installing wm6.5.
This worked in my case.
Check if it does in urs too...
Al the best...
Click to expand...
Click to collapse
what ive done so far,
re-installed the hspl 2.08 and then installed the radio 2.15.50.14 from the following site: http://www.addictivetips.com/mobile/how-to-install-hardspl-2-08-on-htc-hd2/
but now at the bootloader im getting the following error 'upgrade ROM code error Please try again"
What have i done wrong???
thanks
flash hspl ... radio ... then mag ... then try the downgrade to winmo
rubledub said:
flash hspl ... radio ... then mag ... then try the downgrade to winmo
Click to expand...
Click to collapse
after the radio, I cannot download magdlr, it stops at 29%.. Or sometimes doesn't do anything!!
I'd suggest task 29 to wipe the phone completly. Then make sure you have the correct stock rom for your phone. EG if you bought a EURO o2 HD2 then you need to have the o2 3.14 stock rom. Extract the .nbh file from the .exe.
Use SD Formatter to format your SD card, this will wipe all windows 7 partitions.
Then copy .nbh file and place it on the sd card, then boot into boot loader (tri colour screen) and follow on screen instructions. A grey screen should appear at this point.
This will remove Hard spl and restore WM 6.5 and also restore the first of the two splash screens and the radio back to factory settings and will also restore your warrently as well.
GhostXSeries said:
I'd suggest task 29 to wipe the phone completly. Then make sure you have the correct stock rom for your phone. EG if you bought a EURO o2 HD2 then you need to have the o2 3.14 stock rom. Extract the .nbh file from the .exe.
Use SD Formatter to format your SD card, this will wipe all windows 7 partitions.
Then copy .nbh file and place it on the sd card, then boot into boot loader (tri colour screen) and follow on screen instructions. A grey screen should appear at this point.
This will remove Hard spl and restore WM 6.5 and also restore the first of the two splash screens and the radio back to factory settings and will also restore your warrently as well.
Click to expand...
Click to collapse
Thanks for this info, will try it. Have you got a link to task 29? Is it a software?
No but it is all over XDA. I think you'll find it someware on the WM 6.5 thread. If that doesn't work your nand will be stuffed but it has allways worked for me!
GhostXSeries said:
I'd suggest task 29 to wipe the phone completly. Then make sure you have the correct stock rom for your phone. EG if you bought a EURO o2 HD2 then you need to have the o2 3.14 stock rom. Extract the .nbh file from the .exe.
Use SD Formatter to format your SD card, this will wipe all windows 7 partitions.
Then copy .nbh file and place it on the sd card, then boot into boot loader (tri colour screen) and follow on screen instructions. A grey screen should appear at this point.
This will remove Hard spl and restore WM 6.5 and also restore the first of the two splash screens and the radio back to factory settings and will also restore your warrently as well.
Click to expand...
Click to collapse
Yes, even i suggest you the "flash via micro sd card" method becoz it works in worst cases. and follow all the steps sequencely. good luck
Task29 gives an error 290 and doesn't complete.
Im getting frustrated... What can i do next
task 29 now wipes my phone but everytime i flash a new rom is crashes at 9% or 10% and then i get the error 290.
i downloaded the stock rom for my phone... argggh what can be done?
thanks
Sounds like nand is dead. Looks as if you will have to return it to get it fixed!
i must agree with ghost ... sounds like you flashed the poor baby to death :'( sad sad day! and very rare i might add!
GhostXSeries said:
Sounds like nand is dead. Looks as if you will have to return it to get it fixed!
Click to expand...
Click to collapse
cannot believe i messed it up.......
know where i can send it for repair? will HTC cover it under warranty? will they be suspicious?
anyone? do i need to ring my phone contract people or go directly to HTC?
Thanks
Depends how old it is. It may need to go directly to HTC to get it fixed.
I read somewhere that error [290]: Invalid Command - the ROM Update Utility has encountered communication errors during the update process.
Try changing the usb cable/connect directly to usb port (not usb hub) if you still want to use usb for flashing.
I always use the sdcard method when there's a problem flashing via usb. Rename RUU_signed.nbh (extract from stock rom exe package) to LEOIMG.nbh and copy the file to sdcard (sdcard MUST be formatted as FAT32 - use HP format tool). Put sdcard into the phone and boot into bootloader mode ... see if it works ...

HD2 bricked!! Need urgent help from anyone!!!

Hello together,
I had since thursday last week a HD2 NAND flashed to Android IceCreamSandwich,
but after a reboot i dont know why i got a white screen on startup und nuttin happens. So i tried several Troubleshoots to flash again but nuttin happens!!!!
I have the normal HD2 not the TMobile one and got HSPL 2.08SPL on
my Troubleshoots:
Task 29 - Fail because corrupt Image!
HSPL2 - Try to flash to SPL or HSPL no delete/change!
HSPL3 - Try to flash to SPL or HSPL no delete/change!
HSPL4 - Try to flash to SPL or HSPL no delete/change!
Stock Rom - cant find any Official Rom for my Serial: HT031NW03079, and downloaded GERMAN one v.1.66, TURKISH one v1.66 & v.3.14, WWE one v1.66 & v.3.14, WWE ASIA onev1.66, but every try with USB Cable fail with 1% or Image Corrupt Errormessage or hang up on 0%. Tries over SD Card fail every time with
Errormessage 18003 radio v2-fail.
Please Help me!!!
back to winmo use sd card method..
If you can enter in bootloader (with color band) VOL.DOWN + POWER
plub usb to pc and flash a stok rom
I tried this with several Official Roms but no one function..
still hang on 0 % or get a Errormessage on 1% that Image is corrupt over USB
and over SD every try hang with "Errormessage 18003 and Radio_V2 - Fail
LEOIMG.nbh - FAIL
Update Terminate
UPDATE FAIL
You didn't brick it man. Just flash CLK or MAGLDR.
I tried DFT_LEO_MAGLDR113_DAF and it gone 100% but after it I got the Error [270] File is Corrupt over USB.
Try to install MAGLDR over HD2 Toolkit, but hang on 0 %
Try to install CLW over HD2 Toolkit, it gone 100% but after it I got the Error [270] File is Corrupt
Try to install MAGLDR over SD with renameing magdlr.nbh to leoimg.nbh
Update Success but still white screen.. try to open phone with holding power key to enter magdlr menu no sucess - still white screen
You didn't brick you phone. The only serious brick is when you turn on the phone and it vibrates about three of four times. If that's not the problem, i'm sure that you just did someting wrong.
What i suggest is to read the steps in the link very well:
http://forum.xda-developers.com/showthread.php?t=893948
Be aware of the following things;
1. Flash hspl 2, when u use vista: richt click on 'Run as administrator'!! and continue to the screen (make sure phone is connected with a good cable)
2. Flash radio, also run as administrator
3. Make sure you use task 29, Hold volume down and press power button. Wait till you see USB. Then you can flash task 29
4. Use MAGLDR, use volume down and press power button. Flash it (don't forget run as administrator or else you get an error!!
5. Flash CWM via usb flasher (Use the right partition size)
6. Clean SD card with panasonic sd-formatter.
7. Put rom on sdcard and install rom via CWM.
Goodluck!
Greetings,
Arjan
First things first- wrong forum. You have higher chances of getting help in the Q&A section.
Coming to your issue, check if you have a proper USB cable. Most of your error seems to be related to corrupt images, USB cable could be the culprit.
Next, use a different port and reinstall WMDC/ ADB drivers (install them first)
Finally, redownload task29, magldr or cLK images just in case. Use a SD Card that is less than 8GB in size, formatting it in windows with default cluster size.
As long as you are able to get your phone to boot to the tricolour screen, you have not bricked it.
Swyped from my HTC HD2 (ICS 4.0.4)
NLsalvador said:
You didn't brick you phone. The only serious brick is when you turn on the phone and it vibrates about three of four times. If that's not the problem, i'm sure that you just did someting wrong.
What i suggest is to read the steps in the link very well:
http://forum.xda-developers.com/showthread.php?t=893948
Be aware of the following things;
1. Flash hspl 2, when u use vista: richt click on 'Run as administrator'!! and continue to the screen (make sure phone is connected with a good cable)
2. Flash radio, also run as administrator
3. Make sure you use task 29, Hold volume down and press power button. Wait till you see USB. Then you can flash task 29
4. Use MAGLDR, use volume down and press power button. Flash it (don't forget run as administrator or else you get an error!!
5. Flash CWM via usb flasher (Use the right partition size)
6. Clean SD card with panasonic sd-formatter.
7. Put rom on sdcard and install rom via CWM.
Goodluck!
Greetings,
Arjan
Click to expand...
Click to collapse
1. I have a Win7 / 64 Bit Notebook and started everything also with "Run as Adminstrator" but if i try to change the HSPL to 2.08.000 the Program says "It´s done" But on the phone still SPL-2.08.HSPL appears CotullaHSPL!
2. Which Radio i need? I tried to install Radio_Leo_2.15.50.14 but still hang on 0%
3. Task29 hang on 0% or get 100% with Errormessage that Image is corrupt.
4. No way to install MAGDLR, eather it hang on 0% or on 1% with Errormessage Image is Corrupt, try to install MAGDLR over SD and Update success, but can not enter MAGDLR menu by holding Power Key. White Screen Appears nothing else.
5. no way without MAGDLR
6. no way without MAGDLR
m4gnum87 said:
1. I have a Win7 / 64 Bit Notebook and started everything also with "Run as Adminstrator" but if i try to change the HSPL to 2.08.000 the Program says "It´s done" But on the phone still SPL-2.08.HSPL appears CotullaHSPL!
2. Which Radio i need? I tried to install Radio_Leo_2.15.50.14 but still hang on 0%
3. Task29 hang on 0% or get 100% with Errormessage that Image is corrupt.
4. No way to install MAGDLR, eather it hang on 0% or on 1% with Errormessage Image is Corrupt, try to install MAGDLR over SD and Update success, but can not enter MAGDLR menu by holding Power Key. White Screen Appears nothing else.
5. no way without MAGDLR
6. no way without MAGDLR
Click to expand...
Click to collapse
trying it on other computer with a good cable.maybe it's your laptop has something wrong.
try the goldcard method (you cannot generate it for free anymore, but you can google for a good one searching the CID for your sd, try several sd until you will find an sd with a know CID and a goldcard image ready to download for your CID) [try with sandisk/kingstone 2gb, goldcard is not supported with SDHC like 16gb one], and flash from sd in bootloader the nbh image extracted from wwe RUU (you will find *.nbh image under temp folders when you run *RUU*.exe)
maybe with goldcard you can force radio flashing
also try mtty and some tasks (like 2a if i remember well) that try to repair your bad blocks
if you can't solve with these 2 method, sell it on ebay and buy a new one for the same price
The official roms can be extracted with winrar, extract it and copy RUU_signed.nbh to the root of your sd card. Insert the sd and boot it holding volume down and when entered bootloader press volume up. Now it should put it back to WinMo. Then Flash HSPL and Magldr.
m4gnum87 said:
Hello together,
I had since thursday last week a HD2 NAND flashed to Android IceCreamSandwich,
but after a reboot i dont know why i got a white screen on startup und nuttin happens. So i tried several Troubleshoots to flash again but nuttin happens!!!!
I have the normal HD2 not the TMobile one and got HSPL 2.08SPL on
my Troubleshoots:
Task 29 - Fail because corrupt Image!
HSPL2 - Try to flash to SPL or HSPL no delete/change!
HSPL3 - Try to flash to SPL or HSPL no delete/change!
HSPL4 - Try to flash to SPL or HSPL no delete/change!
Stock Rom - cant find any Official Rom for my Serial: HT031NW03079, and downloaded GERMAN one v.1.66, TURKISH one v1.66 & v.3.14, WWE one v1.66 & v.3.14, WWE ASIA onev1.66, but every try with USB Cable fail with 1% or Image Corrupt Errormessage or hang up on 0%. Tries over SD Card fail every time with
Errormessage 18003 radio v2-fail.
Please Help me!!!
Click to expand...
Click to collapse
Try this http://forum.xda-developers.com/showthread.php?t=668347
ph03n!x said:
First things first- wrong forum. You have higher chances of getting help in the Q&A section.
Coming to your issue, check if you have a proper USB cable. Most of your error seems to be related to corrupt images, USB cable could be the culprit.
Next, use a different port and reinstall WMDC/ ADB drivers (install them first)
Finally, redownload task29, magldr or cLK images just in case. Use a SD Card that is less than 8GB in size, formatting it in windows with default cluster size.
As long as you are able to get your phone to boot to the tricolour screen, you have not bricked it.
Swyped from my HTC HD2 (ICS 4.0.4)
Click to expand...
Click to collapse
i tried as you told with reinstalling the drivers for WMDC and redownloading all other things but still the same s... I think the problem is the 2.08.SPL i cant change it or delete it.. or maybe a cache of anything is bricked so he hang on 0% or 1 %... i dont know im so frusted
look at my post, try goldcard method, should force flash process
pirlano said:
look at my post, try goldcard method, should force flash process
Click to expand...
Click to collapse
how i can go over the gold card method if my hd2 is not running? i see in the tutorial that i must get to storage mode and get the SD Cards Serial number..???
jak11 said:
Try this http://forum.xda-developers.com/showthread.php?t=668347
Click to expand...
Click to collapse
The Rom is still no more avaiable to download and if start mtty i have no selection for USB :S
still not solved, i can guide you through skype it will be easier
Task29 ve HSPL 3 araçlarını tekrar indir. Belki sorun onlardadır.
Download Task29 and HSPL 3 again, the problem may belong them.
nphaibk said:
still not solved, i can guide you through skype it will be easier
Click to expand...
Click to collapse
for sure i will be avaible in 3 hours if you want?

Categories

Resources