(Bare with me, this IS wm6 related)
Okay, so i got this qtek 9090 from a trade online, and the owner pointed out that he had used it for some time now and it worked without problems.
However that seems not to be my experience. At first I was a little worried that it did not came with a charger.. Only a USB cable. No worries i thought, I will just charge it through USB. Now I have had some experiences where phones wouldn't charge from some of my computers, apparently because of some boards that put out lower amps than others. However I knew atleast one computer should have no problem charge ordinary cell phones.
So i plugged it in, and to my worries the battery kept going down... Untill the phone was dried from power and everything got lost again.. and again.. and again.. It seemed a little odd that it apparently deleted everything each time, since the backup battery indicated 100%.
So at last it went into flightmode and I shut it down with the powerbutton and let it be connected.. The first many hours nothing happened.. But suddenly, when i did an occasional check, it said 3% battery. I went to sleep and the next morning it was fully charged. I used it all day in school and it held its power real fine.
Now I got the feeling that this probably was caused by the low amp output from the computer, making it unable of charging to the extend where the phone would still be able of running whilst charging. So i figured i would order a 220v (the powercurrent here in Denmark) -> 5v USB that outputs 700mA, to make a quicker charge.
Well, to day I was gonna receive that adapter, and since I'd read that the wm6 apparently draines the battery some bit, I waited untill today to upgrade to wm6.
I upgraded and everything truely runs quick and stable. But when i recieved the adapter and plugged it in, i was horrified. The power kept going down, as I had experienced when it was plugged into USB.
Now my girlfriend really wanted to play bejeweled on this thing, so she did and then shortly afterwards we took a few hours nap. I had her plug it in the new adapter to charge it. When i woke up i saw the screen blinking.
I could se it was rebooting over and over again, as it had done the first time it completely lost power..
Now besides that extremely annoying charging problem, I now had another concern....
The boot screen shows NONE next to the R and the G.
Next to the D is the wm version displayed.
Any help would be greatly appreciated.
red LED?
Hm.. By doing a hard reset it shows numbers next to R and G again.
It continuely reboots, display boot screen, shuts down, LED is red, reboots, displays boot screen, shuts down, LED is red again and again.
If i hard reset it some times it will at one point stay off, but the LED still lights red.
And now I question wether 700mA is even enough for charging the BA?
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
jakubd said:
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
Click to expand...
Click to collapse
AFAIK the lower the mA output, the slower the charge period.
I have had wifi, bluetooth, beam off. I've set shutdown to 2 minutes. I've set it to low brightness and etc.
As i mentioned it had no problems going a whole day of usage in school.
Didn't know about the bug in wm6 that makes only the screen shut off, but at the momemt i can't even boot the device, apparently because it has no batterypower. And having it connected to the charger makes no real difference (other than it will display the bootscreen and perhaps even the Windows Mobile welcome screen thing, for a few seconds.. then go dead again.)
I've had it in the charger for about an hour or two, still not enough power to boot it up.
It feels like it's just not charging sometimes.. And other times it will charge just fine.
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
jakubd said:
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
Click to expand...
Click to collapse
Hmm, i see. I just don't understand why it's not charging then :/
trylleklovn said:
Didn't know about the bug in wm6 that makes only the screen shut off
Click to expand...
Click to collapse
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
trylleklovn said:
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Click to expand...
Click to collapse
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
jakubd said:
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
Click to expand...
Click to collapse
Okay.
It's odd still. When i connect the charger the right LED starts to light red.
If it means that its not charging, there must be something wrong, since it only happens when connecting the charger..
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
jakubd said:
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
Click to expand...
Click to collapse
I KNOW that, but it is not going amber. It stays red all the time.
Found this thread that discusses a similar problem; http://forum.xda-developers.com/archive/index.php/t-233782.html
Apparently it shows RED light all the time if the battery is dead.. However i hardly doubt that the battery, which could power the phone just fine for and entire day, should be dead.
However, one suggestion in the thread was to take out the battery for some time and then try again. So I will do that for now.
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
trylleklovn said:
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
Click to expand...
Click to collapse
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
motisu said:
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
Click to expand...
Click to collapse
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
trylleklovn said:
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
Click to expand...
Click to collapse
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
motisu said:
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
Click to expand...
Click to collapse
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
trylleklovn said:
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
Click to expand...
Click to collapse
I have found that if you only use the USB cable to charge, it takes much longer (if at all) to charge if it is on. Thats why I bought cradles that have external power suppies as well as the USB sync cable. With this configuration, it gets to full charge in about 90 minutes.
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
trylleklovn said:
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
Click to expand...
Click to collapse
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
motisu said:
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
Click to expand...
Click to collapse
Yeah, i tried that. As soon as i press the power button it goes to red again.
Update..
A litte update (i might as well document everything I find out here, if anyone should run into a similar problem).
Now, I've had the device connected to the charge for some time now.
What happens is that the device boots up, automaticly dimms down to no light (since i once had hold down the power button, to dimm down light).
Then it boots up, and i can see everything running.
I can navigate to the battery status menu, which shows
Battery: 0% (charging)
Backup battery: 25%
After a few minutes the device shuts down, and the LED goes red again. But after about a half a minute it will try to boot up again, and it goes through everything again.
What I've noticed is that the backup battery slowly increases, and while im writing it has gone all the way to 75%. The good thing about this completely automatic procedure is that it apparently slowly charges, at least, the backup battery.
My theory is that the backup battery has first priority in the system, so that the regular battery wont charge untill the backup battery is up. And since the backup battery can't apparently be used for actualy powering the system, the system will continuesly reboot because of lack of power, theoreticly untill the backup battery reaches 100% and it starts to charge the regular battery.
The whole problem seems to be cause by some charging malfunction, so that both batteries has been completely discharged. I hope that by letting it continue to reboot, charge, reboot, charge, etc. it will revive the battery.
I will return with more info tomorrow.
Any suggestions are still greatly appreciated.
SITUATION
My Cingular 8500 does not power on. I have tried connecting it to wall charger as well as USB cable. The red or the orange light also does not come on. I tried all resets also but nothing worked.
BACKGROUND
a. My phone suddenly went off when I was opening the sliding keyboard. It had a decent (60%) charge at that time. After this it refuses to come on.
b. Only addition to the phone in the last 3 months has been a 2GB MicroSd Card. I inserted this card 4 days back and it was working fine.
c. The device is around 6 months old (but its unlocked, running WM6 and does not have any warranty)
d. I have been using the original wall charger to charge this phone regularly.
HELP REQUIRED
1. Is there a way to check if the problem is with the battery or with the phone? I do not have a spare battery.
2. Should any light come on if I connect the phone to charger without the battery inserted in it?
Thanks!
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
i have the same situation going on ... except with mine the screen faded out...it came back on once...and faded out again and will not turn back on.. when i put it on the charger it was a red light.. and will not turn on or soft reset, or enter bootloader or hard reset. .. in addition i tried the method above and nothing has worked.... any other suggestions...my phone was working fine when this happened out of nowhere... i dont have insurance either i bought the phone from someone off of craigslist..help is greatly appreciated
I am having the exact same problem, I had about 30% charge, then it just shut off, and now will not come back on under its own power or via USB nor charger. I tried connecting the charger then inserting the battery, but I do not get any indicator lights at all.
I was running WM6, and the most recent thing installed was the pointUI home screen replacement app.
has anyone experienced this before?
theconcon said:
SITUATION
My Cingular 8500 does not power on. I have tried connecting it to wall charger as well as USB cable. The red or the orange light also does not come on. I tried all resets also but nothing worked.
BACKGROUND
a. My phone suddenly went off when I was opening the sliding keyboard. It had a decent (60%) charge at that time. After this it refuses to come on.
b. Only addition to the phone in the last 3 months has been a 2GB MicroSd Card. I inserted this card 4 days back and it was working fine.
c. The device is around 6 months old (but its unlocked, running WM6 and does not have any warranty)
d. I have been using the original wall charger to charge this phone regularly.
HELP REQUIRED
1. Is there a way to check if the problem is with the battery or with the phone? I do not have a spare battery.
2. Should any light come on if I connect the phone to charger without the battery inserted in it?
Thanks!
Click to expand...
Click to collapse
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
Eamonn said:
I am having the exact same problem, I had about 30% charge, then it just shut off, and now will not come back on under its own power or via USB nor charger. I tried connecting the charger then inserting the battery, but I do not get any indicator lights at all.
I was running WM6, and the most recent thing installed was the pointUI home screen replacement app.
has anyone experienced this before?
Click to expand...
Click to collapse
It wont power on threw charger without a "good" battery plugged in.
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone. If not just go to ATT wireless store and see if they have one you can try and buy.
demo23019 said:
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone.
It wont power on threw charger without a "good" battery plugged in.
Click to expand...
Click to collapse
I really hope thats the problem because it's an easy solution, otherwise I fear it might be toast. thanks for your advise
No light when connected to charger
Thanks all for your responses!
markafreeman said:
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Click to expand...
Click to collapse
Dear Markafreeman, I tried the entire routine above but no help.
demo23019 said:
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
It wont power on threw charger without a "good" battery plugged in.
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone. If not just go to ATT wireless store and see if they have one you can try and buy.
Click to expand...
Click to collapse
Dear demo23019, I am not sure if I understand the above correctly. Should the Power LED light up "red" when battery is not inserted?
Once I connect the phone to charger (wall or USB), without the battery inserted in it, no red light comes on.
Does this mean that there is some problem with the phone hardware?
theconcon said:
Dear demo23019, I am not sure if I understand the above correctly. Should the Power LED light up "red" when battery is not inserted?
Once I connect the phone to charger (wall or USB), without the battery inserted in it, no red light comes on.
Does this mean that there is some problem with the phone hardware?
Click to expand...
Click to collapse
Yea the power LED should light up red with out a battery plugged in. Check the usb plug on the bottom of your phone, make sure the middle piece inside is still there and didnt break off.
demo23019 said:
Yea the power LED should light up red with out a battery plugged in. Check the usb plug on the bottom of your phone, make sure the middle piece inside is still there and didnt break off.
Click to expand...
Click to collapse
Oops. My phone's power LED does not light up when I connect it to the charger without the battery inserted in it.
I have checked the following :
a. usb plug is fine (I checked it by plugging it into the Y cable for the USB charger. The LED on the Y cable lights up when I connect the USB plug into it
b. The middle piece inside the socket at the bottom of the phone is still there and shows no signs of damage.
c. The wall charger is also working fine.
Does this conclude that the phone has a hardware fault and this is not linked to the battery being dead?
Similar Problems
I just had the same problem. I had it happen to my Att Tilt and then to my cingular 8525. You should check out this thread and maybe post your info there too, it would be nice to see everybody post in the same thread so we can figure out what's going on.
http://forum.xda-developers.com/showthread.php?p=1783005&posted=1#post1783005
yh
yh i got the same problem, i touched the power button so it wld go into standby, and it then refused to turn back on, even when i soft resetted it. Plugged it into the wall charger without the battery and there is no red power light coming on.
I've got a MDA Vario II and though im gettin a replacement, it kinda sucks as it seems im gna lose all my data
can we try to determine in more detail what people installed before they experienced this?
I just pulled it apart, and cleaned the inside to no avail, nothing seems to be awry, atleast not to my untrained eye, however it did get me thinking.
I listen to music on my tytn all the time, and over time the usb connector has become quite loose, frequently losing connections over activesync and music comes and goes from both lef and right. if the USB connector is shot, then when I plug it in it won't register that there is power, nor will it have the power to light up the red light indicating there is no battery. also, if the usb link is shot, then the phone wasn't charging so my battery is likely dead.
now to test this out I need to have a verified 100% charged battery.
I currently have the same problem. It will not charge via wall/usb. It flashes red once and that's it. Without the battery and plugged in, I get a solid red light. I tried plugging it into the wall charger without a battery and then putting my battery back in. The red light just turns off. That's it. I can get an active sync connection with a dim white screen, but I do not have enough juice to try flashing a new rom. If anyone has issues like these, are you also able to get an activesync connection?
TIA
EDIT: Is it possible to bypass the low battery protection when flashing a rom? My battery is somewhere around 40% so it would be safe.
Update:
Okay, I purchased a new oem battery and a battery charging dock. This way I can charge the battery without the phone before I attempt to flash a new rom.
I still would appreciate it if anyone who has seen these symptoms (white screen BUT with lots of vibrating / no charging / no bootloader) could give me a few pointers. I've exhausted the Wiki and so far it seems my only option to save the phone is to flash a new rom. Thanks in advance to anyone willing to give me some advice.
My 2 months old Touch HD doesn't charge the battery anymore.
If i plug the power cord, the notification led turns red for 5-7 sec., then it turns off, and the battery meter shows no charging.
I can sync it with PC but runs again on battery, even the check box (under the power meter) is unchecked.
The only way to charge the battery, is to let the battery drains out (the phone turns itself off) and remove the battery from phone for few minutes.
I have the original ROM 1.57.831.1 (47324) WWE from 04/08/09 and i tried one hard reset ("clear storage" from settings).
Does anyone know how to fix this ?
I'm verry disappointed. Now it does'nt charge even i remove the battery.
I think i'll try the warranty service.
No other suggestions ?
Are you sure it is the problem of the HTC HD? I got hte same problem. But because I charged my second battery which was newly bought from the official website HTC UK. My original battery works well. So I returned my second battery.
Try another battery.
ci6i said:
I'm verry disappointed. Now it does'nt charge even i remove the battery.
I think i'll try the warranty service.
No other suggestions ?
Click to expand...
Click to collapse
yep, same here...
my girlfriend and me, we own a HD, pretty much the same issue...
My device frist stated "unkown main battery status" and has been only willing to charge the battery while switched off and connected to PC (charger doesn't work).
My grilfriend's one now refuses to start at all.
One thing for sure - its not battery related since my fully recharged battery doesn't make her device starting.
I sometimes pulled out the battery without swichting the device off, or left it running for days before reseting it...i guess that might have triggered the problem...
gotta send it in, hopefully they don't mind my custom rom!
ci6i said:
My 2 months old Touch HD doesn't charge the battery anymore.
If i plug the power cord, the notification led turns red for 5-7 sec., then it turns off, and the battery meter shows no charging.
I can sync it with PC but runs again on battery, even the check box (under the power meter) is unchecked.
The only way to charge the battery, is to let the battery drains out (the phone turns itself off) and remove the battery from phone for few minutes.
I have the original ROM 1.57.831.1 (47324) WWE from 04/08/09 and i tried one hard reset ("clear storage" from settings).
Does anyone know how to fix this ?
Click to expand...
Click to collapse
I had this problem to.... Change of USB cable did the trick! So.....it's possible that your USB mini cable is dead. Try another USB if you haven't tried it yet.
Thank you all.
alper1 said:
I had this problem to.... Change of USB cable did the trick! So.....it's possible that your USB mini cable is dead. Try another USB if you haven't tried it yet.
Click to expand...
Click to collapse
I don't think it's the cable because i let the phone charging on my desk and suddenly, after few minutes (sometimes 1 min, sometimes 60 min) it stops charging (without touching/moving the cable),
ccieuser said:
...Try another battery
Click to expand...
Click to collapse
I'll try to find another battery but my friends use Nokia
4irm said:
...One thing for sure - its not battery related since my fully recharged battery doesn't make her device starting.
I sometimes pulled out the battery without swichting the device off, or left it running for days before reseting it
Click to expand...
Click to collapse
Well, in your case, for sure its not battery related.
After i left the battery out of the phone for 6 hours, it start charging again for 45 min then, the notification led start blinking red and green. After 2 minutes, the led turns off and i started the phone with 40% battery life.
It's driving me crazy and i don't know what to think!
I start to believe it's a battery problem but i'll ask for service opinion too, since i payed a lot of money for this.
Solved
My handset was repaired in service.
The problem was hardware related, generated by malfunction of switching power alimentation mechanism to motherboard.
Hello
My battery sucked, like going from 100 to 20 in 10secs so i asked for a new one from huawei greece. They sent me a new battery and when i put it into the phone and tried to boot it phone didn't boot. I thought it was because the battery was empty and when i connected it to charge first the light was blinking red and then phone boot up to the battery screen. 15min later i realised the phone was boot up and the red light was blinking red and not like staying red which is the light when you charge it with no battery. the percetange was 0%. i left it there for a little bit but nothing happend. then i tried to turn it off while it was connecting to the charger but that just boot up again with the same red blinking light and 0% percentage. I'm on aurora sp on top of aurora v20. When i try the old battery everything is working ok like it charges and everythinh. Could someone help me out?
Strange
Try this connect your phone to usb power without battery inserted. Then turn on when phone boot insert your new battery into your phone let charge until green led or 100%. And install Battery Stats and post details about your batt.
dark_vader said:
Strange
Try this connect your phone to usb power without battery inserted. Then turn on when phone boot insert your new battery into your phone let charge until green led or 100%. And install Battery Stats and post details about your batt.
Click to expand...
Click to collapse
i've tried that nothing changed. i let it boot up without the battery then put it back in without pulling off the charger and it still seemed to be without battery just with the usb cable. i got back to official gingerbread, no rooting and stuff now but still doesn't charge. the weird thing is that the very first time that iconnected it to the charger, when the phone was off, the light started blinking red without phone getting into "battery screen" and after a while it was at battery charging screen. 15min later it was booted up and "no charging" status
Cybergiannis said:
i've tried that nothing changed. i let it boot up without the battery then put it back in without pulling off the charger and it still seemed to be without battery just with the usb cable. i got back to official gingerbread, no rooting and stuff now but still doesn't charge. the weird thing is that the very first time that iconnected it to the charger, when the phone was off, the light started blinking red without phone getting into "battery screen" and after a while it was at battery charging screen. 15min later it was booted up and "no charging" status
Click to expand...
Click to collapse
Okay. Ask Huaei to change your battery since it's damage for another one you have and can active warranty do that