Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
So my phone became frozen after one of my friends was messing around with it. Now whenever i take out the battery and then try to start the phone again, my trinity will become frozen at the windows startup screen. Interestingly, the " In Call" icon that indicates the phones volume will appear in the windows startup screen as well.
what can i do? Can i try to reset the phone back to factory settings? Would this be even possible since i upgraded to windows mobile 6
any help would be greatly appreciated
ttt
what happens during a full reset if you install windows mobile 6? will the phone revert back to wm5?
saku39 said:
ttt
what happens during a full reset if you install windows mobile 6? will the phone revert back to wm5?
Click to expand...
Click to collapse
it reverts back to the last rom installed...
if it was wm6 after hard reset it will be wm6...
if it was wm5 after hard reset it will be wm5...
This happened to me.
Before a hard reset... try removing the Storage Card and do a Soft reset. My card was corrupted and the Mail Attachments folder (on the Card) locked Trinity at the Start/Home screen.
Worth a shot. Good luck.
I had the same problem after connecting my bluetooth headset. A hard reset fixed it.
do you use HTCHome ?
if yes uninstall it
I upgraded my uni with ranju rom 2months ago and worked perfect.Yesterday after a call the uni froze when i restarted, the uni black out. have tried both hard and soft reset. Nothing happens in soft reset, but hard gives U " Press 0 to restore to factory default and X to exit". but if i press 0, the uni goes off again.,
Battery? Can you enter a bootloader and re-flash the ROM?
I can't get pass "Press 0 to restore to factory default -Press X to exit" screen
i also have same problem with you. and i have connect my device to PC usb cable, then PC detect my universal but cant recognize it as pocket pc.
please anyone help us.....
hello
hi all, and thanks in advance for reading this thread.
my cousin gave me his qtek 9000 saying that it was dead. being a dumbass, me decided to try and give it back life. as mentioned before, me a dumbass. After seaching the web for hours, i would normally be now saying, i give up. but no.
so , please. help.
the only thing i can tell u is that when i plug it in the pc, a red light starts bleeping. Won't turn on, soft and hard reset do not seem to make any effect, nor the power+light button.
again, please, help.
Had exactly the same...my qtek 9000 was just lying in the closet for a long time and would not boot anymore...
When I used it last time al was fine. I figured a dead battery so bought a new one...
It would give me the red LED while charging, would not be recognised on the computer etc.
Did a hard reset and then got it into the bootloader...
Had to run my laptop on XP as under Win7 it would fail to flash or do anything, but under XP it flashed properly.
After flash installed my back-up and all seems to be running fine now!
May be it helps anybody...
it happened after i soft-reseted my device today, the HTC icon didn't show up.
i can't really turn it on normally although i did hard reset. Please, all advices would be so appreciated
What did you did before the soft reset?
some new software installed?
What happens exactly when you try to turn on the Niki?
Can you put the Niki in bootloader mode?
I installed Spb Mobile Shell. It needs to soft reset after changing the original Spb Mobile Shell skin. I took the skin from PC to my device via Softick Card Export.
And now my Niki screen only shows "smart mobility" without being able to show HTC logo. I guess it can't be used to boot
Help T_T
carlosmozas said:
What did you did before the soft reset?
some new software installed?
What happens exactly when you try to turn on the Niki?
Can you put the Niki in bootloader mode?
Click to expand...
Click to collapse
OMG..thnx so much..gracias
i found a member post how to do it here
also thnx to tom_codon for starting the thread and colaito for sharing us how to put it in bootloader mode
but special thnx is dedicated to u Mr. carlosmozas, for giving me clue how to solve it
problem solved..thanks so much
Please help, i installed stock WPH 6.5 on my HD2 and it worked fine suddenly i tried to unlock it and the slider freezed i turned it off.... Now i cant turn it on, hard reset , soft reset , cant enter bootloader obiviosly nothing.When im trying to turn it on it just softly vibrates,very,very softly u cant even feel that.Please help i tried to put it in fridge i tried everything i found but it cant boot. PLEASE HELP IF YOU CAN !!!
Plug in the charger? Change battery?
hengsheng120 said:
Plug in the charger? Change battery?
Click to expand...
Click to collapse
I tried everything buy nothing
It sounds like your device had sudden hardware failed. You will probably have to either replace the mainboard or JTAG the device. My money would be on replacing the mainboard as it did boot after you flashed Windows Mobile 6.5 so it being software bricked were you can use JTAG to fix is unlikely.