Hi everyone...
I've tried to cid unlock my artemis but I wasn't able to do it...
any clues?
When I trie to install a rom (oficial Portuguese 3.14) it gives me Invalid vendor ID...
What could I been doing wrong?
Thanks in advance!
i had trouble cid unlocking my artemis, i dont know what i did but i done it, this is what i did tho.lol
download Uspl - mine came with these cab files so i installed them on the phone.
''Cert_SPCS''
''EnableRapi''
link to pc and get active sync connection.
run ''start_uspl'' (on pc which opens a dos screen)
phone screen will go off into white or black screen.
(should see a penguin)
after that ''ROMUpdateUtility'' will automaticy start.
*cant remember if you need soft reset or not - think you do so active sync is enabled again, try with and without soft reset!
click through untill it starts to update, your phone will go into bootloader mode showing a usb connection. it will automaticly go into a gray screen with a loading bar.
SPL;1.11.0000 should now be displayed at boot
if this does not work try hard reset on phone and reinstall active sync on pc.
use uspl cmon to flash any rom..
spl 1.11.cmon
Related
so i installed SPB pocket plus and now my wizard freezes at the startup splash screen after a soft reset and doesnt load.
HELP!
it stuck at the screen where it tells u the IPL, SPL, GSM, and OS versions
tried hard reset and still doesnt work
just download the appropriate ruu for your phone and update it
you dont need to be connected to active sync ....just put your phone in bootloader mode and flash it
ftp://ftp.xda-developers.com/Wizard/Roms
download the specific rom for your phone and do as directed ..your phone will work again
bah...second hard reset did it.
*#@(*@# now i gotta reinstall ALL my programs again >:\
Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!
I tried to put flash a rom onto my phone,An when i did the hard the rest it wont load pass the screen that says
ipl2.25
spl 2.25
gms 02.25.11
then the logo cingular
I have tried to restset to factroy default but the same thing happens.
I also tried to connect by usb to pc an wont allow me to connect.
some please help me find out a way to fix it or should i just get a new phone?
twizzymckin said:
I tried to put flash a rom onto my phone,An when i did the hard the rest it wont load pass the screen that says
ipl2.25
spl 2.25
gms 02.25.11
then the logo cingular
I have tried to restset to factroy default but the same thing happens.
I also tried to connect by usb to pc an wont allow me to connect.
some please help me find out a way to fix it or should i just get a new phone?
Click to expand...
Click to collapse
Is your phone CID unlocked ? if it's not CID unlocked,try to unlock and read and follow the unlocking guide by Dr Puttingham in the stickies.If it's CID unlock,it's a bad flash and reflash the rom,get your phone in the bootloaders mode (multicolor screen) connect via usb cable and check if small usb appears at the bottom of the bootloaders screen and run the Ruu application.
cheers !
Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.
need help!!
my cingular8125 stucked in splash screen. however, it can still goes into bootloader mode.
when it is turned on, it only shows these informations:
ipl 2.26
spl 2.26
gsm 2.xx.x
os??? (no information)
some rom problem occurs i guess..
when i tried to flash it with other rom. i go to bootloader mode. connect usb but it doesn't connect in activesync. so i get an error when i start ruu.exe.
is it possible to flash rom on my wizard without using activesync?
or using sd card?
is there a dumped rom so i can flash rom using sd card?
any solutions??
need any dumped rom for my wizard..
SOLVED MY OWN PROBLEM:
for those having the same problem here's how i solved mine..
some things may not necessarily needed..
but these steps worked for me:
first thing first:
download a mtty.exe, if you got a zip extract it somewhere..
get a working wizard, or if your wizard can still backup your image you can..
since in my splash screen os onformation doesn't show up anymore.. sd rom backup on my wizard stucked in bootloader mode didn't work out for me.
so i get another working wizard running in cracing's wm6.5 you can get os images on any cooked rom you want..
1.) kill task manager first on your phone. if your'e using activesync 4.5 go to connections and untick the checkbox for "allow usb connections"
2.) go to bootloader mode (turn off the phone/remove battery then hold camera while powering on)
3.) connect usb you'll see little indication on your lower left part of your screen "usb"
4.) run mtty.exe
5.) choose //wceusbsh001
6.) then type "r2sd all" then enter
7.) you'll see a loading bar on your in your bootloader screen so you can see its progress..
8.)turn off the phone. enter bootlader mode. will ask you if you want to copy images on your sd.
9.) hold voice dial button(upper right-side corner of your phone ) and writing will begin
10.) when its done poweroff and on normally and your wizard is back to business..
cheers!!!