Database Users

My Qtek doens't pass the red, green, blue screen

Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore

Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.

g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.

If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.

g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.

Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.

Thanks for details...

stuck at boot loader -cant connect to pc

Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen

anyone?
ideas?

Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!

every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck

Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.

I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in

Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.

Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight

thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!

Dead Wizard, please help

Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.

hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps

But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?

when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.

i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08

sorry , i can't think of anything that might help you.

same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards

Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.

I brick my htc wizard help please i do not know what to do!!!!!

I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......

brick...
chipis said:
I BRICK MY HTC WIZARD... CAN SOME ONE HELP ME PLEASE???? I OWN A HTC WIZARD FROM CINGULAR 8125 POCKET PC. RECENLY I TRYED TO FLASH MY POCKET PC BUT SOMETHONG HAPPEND.... IT JUST STAYS ON THE CINGULAR LOGO..
IPL 2.21.0001
SPL 2.21.O1ip
GSM 02.25.11
OS 2.18.0.0
AND IT JUST STAYS THERE.....
PLEASE HELP......
Click to expand...
Click to collapse
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck

Thank for answer me and understand what i ment
Ok what software you recoment?. I do not know if i have a unlocked phone but i do know that i used it with t-moble even that my pocket pc is for cingular, i went to those stores that unlocked phones and that it

Help.
I have a Wizard G4 and I tried to install a WM6.5 ROM (TechTeamup Mega Wizard rom) from the default WM5. I did not put in the hard-spl (as I now read) before I tried to flash. Now when it boots, I go strait to the flash screen (tri-color) screen. I tried ot run the hard-spl-G4 and it says it cannot find a device. I have tried to re-flash back to WM5 ROMs that I have found, however it says it cannont complete "ERROR 296: UPGRADE ONLY, which makes me belive I need a G4 Wizard ROM that is a full (not upgrade). What steps should I take now to revert back to a WM5 so I can re-try the "unlock" hard-spl proceedure to make the phone WM6 compatible?
Anyone have any suggestions?
IPL 2.28.0001
SPL 2.28.0001

Download the original ship ROM for your phone.
Turn the phone off.
Press and hold the Camera key, now insert the USB cable, Keep holding the camera key until you get the boot loader screen.
Now run the ROM update to flash back to WM5.

ricozy said:
I try to answer... (sorry for my bad english)
1. Make sure your battery up to 50%, 100% is recommended...
2. turn off u'r PPC
3. press camera,talk, and power button at the same time for a second until your display show 3 colour....
4. plug your cable data from PPC to desktopPC, and make sure your display show "USB", and try to re-flash with other ROMS.....
Good Luck
Click to expand...
Click to collapse
I brick my wizard too... What happened was I flashed my own cook of m6r5 it say successful but on reboot, it shows htc logo then stays ay tricolor screen:
IPL 2.26
SPL 2.26
Bootloader wont work..tried many times but I cannot connect to PC...
Tried ricozy post above, can access 3 color... but still cannot connect to PC...
Please help...anyone..

IF u can enter bootloader...connect to pc...u shud c "USB" written in the left bottom corner ...then flash a rom as usual

Can't CID unlock my Artemis

Hi everyone...
I've tried to cid unlock my artemis but I wasn't able to do it...
any clues?
When I trie to install a rom (oficial Portuguese 3.14) it gives me Invalid vendor ID...
What could I been doing wrong?
Thanks in advance!

i had trouble cid unlocking my artemis, i dont know what i did but i done it, this is what i did tho.lol
download Uspl - mine came with these cab files so i installed them on the phone.
''Cert_SPCS''
''EnableRapi''
link to pc and get active sync connection.
run ''start_uspl'' (on pc which opens a dos screen)
phone screen will go off into white or black screen.
(should see a penguin)
after that ''ROMUpdateUtility'' will automaticy start.
*cant remember if you need soft reset or not - think you do so active sync is enabled again, try with and without soft reset!
click through untill it starts to update, your phone will go into bootloader mode showing a usb connection. it will automaticly go into a gray screen with a loading bar.
SPL;1.11.0000 should now be displayed at boot
if this does not work try hard reset on phone and reinstall active sync on pc.

use uspl cmon to flash any rom..
spl 1.11.cmon