"power will be turned off and you may lose data if you have not saved them do you want to continue"
This messages appears always on phone as my phone is fully charged and there is no problem with power butten but the battery get lows very fast and not normal also if u touch the devcie from the battery side you feel its wormer than normal also there was a virus on the system and I reformatted it but got the same problem please I need a solotion for this problem ASAP please
PS I use the original ROM
why_fadoo said:
"power will be turned off and you may lose data if you have not saved them do you want to continue"
This messages appears always on phone as my phone is fully charged and there is no problem with power butten but the battery get lows very fast and not normal also if u touch the devcie from the battery side you feel its wormer than normal also there was a virus on the system and I reformatted it but got the same problem please I need a solotion for this problem ASAP please
PS I use the original ROM
Click to expand...
Click to collapse
your battery might be dead. did you get the phone wet recently? or do you use it in the bathroom or kitchen where there may be steam in the air?
check the connectors on the battery and the device to make sure they are connecting well and dirt free...
can you try someone elses battery? or buy a new one on ebay or deal extreme or something?
good luck
There is no problem in the battery, because sometimes the device is working and excellent battery hold two days I would expect that viros
If you change the Rom you can solve the problem
I'm sorry if change the Rom can solve the problem????
Note can be useful sometimes power button does not work no response
why_fadoo said:
Note can be useful sometimes power button does not work no response
Click to expand...
Click to collapse
Think you've just stated your problem. This looks like you have a faulty power button where is is jammed pressing down casuing your message to appear as it is constantly trying to turn itself off.
I have the exact same problem. When I turn on my phone I get the 'turn off' message, my battery drains in five hours (I've got three batteries so the problem's not there), and if my phone switches off it turns back on right away (= button jammed). It was water damage due to some annoying stranger at a barbecue.
I've searched this site, tried suggestions, tried other places (one tip is to get a small sliver of card and slide it under the power button cap to try and jolt the power button back), and I think I'm now left with either asking HTC to fix it at a cost, or buy another one on eBay etc.
Good luck with yours, let me know if you get anywhere. I wouldn't mind, it's the power-drain that's killing me
Yes,((smeddy)) I face the same problem where I am if you turn off the device is running itself, but Did you change rum can solve the problem or not
Changing ROM makes no difference, shure it's hardware, and I can't unjam it
I know the cause of problem is caused by virus named ((((REMOTEINF.EXE)))))
states if faced with digging virus name on the PC may be moved to the device if you found a way to delete it from the mobile I hope Aalamni I ask anyone who knows the way to help us teach them that no, thank you
I know the cause of problem is caused by virus named ((((REMOTEINF.EXE)))))
states if faced with digging virus name on the PC may be moved to the device if you found a way to delete it from the mobile I hope Aalamni I ask anyone who knows the way to help us teach them that no, thank you
Related
This JasJar I have Always have problem waking up after period of inactivity. If I had it powered off for too long, I cannot bring it back to life with any hardware button, except the reset. Usually I can still see the green light flashing indicating the phone in on and working. But I had also tried to call it, but it won't ring. As a PDA the problem wouldn't bother me too much, but as a Smartphone it mean I might have missed a few important calls
the only solution i have now is i go to settings, power, advanced and i disable the "turn off device if not use for" option
it works all the time with me but it eats the battery, specially if i am connecting my BT headset
Please if anyone has a solution let me know
thanks
i forgot to say that it happens even if i take the SIM card out of the device, so i do not think it is a SIM card issue
i do not have and SD cards
Any Help?
it happens randomly with no specific reason, but I tend to believe it's due to a third party s/w. If you made a hard reset and kept using the device with only the standard applications, the device will be very stable except the bluetooth issues.
The issue of the PPC power button, whatever a soft one or a hard one, has been consistently existed since I bought my first PPC with PPC2000. I am so disappointed that it is exactly the same case after some 6 years...
It is usually due to some imcompatibility between the system and some today-enhancing add-ons, which seem necessary for us but sometimes however causing problems like a deep snooze...
thanks for ur answers, actually i do not think it is related to 3rd party applications on today screen plugins, since i already had reflashed my device and i am running now with no applications installed, i am not sure what Phono can do for me i will try to contact them today and see if i can get a replacement or what?
yet any other ideas will be really appreciated
Same problem in my device can any one help me Please
Hey, I had this problem too...
The only way I stopped my PDA from freezing like this was to disable the auto power off feature in Settings/System/Power and keep the backlight turned on (but lower without it plugged in) Settings/System/Backlight.
This helps with other bits too, makes the delay in the unit from ringing less and connection time faster.
Regards.
Dave.
jmdrizen said:
Hey, I had this problem too...
The only way I stopped my PDA from freezing like this was to disable the auto power off feature in Settings/System/Power and keep the backlight turned on (but lower without it plugged in) Settings/System/Backlight.
This helps with other bits too, makes the delay in the unit from ringing less and connection time faster.
Regards.
Dave.
Click to expand...
Click to collapse
Thanks dear .. I will tray it I hope it will fix this problem.
jmdrizen said:
Hey, I had this problem too...
The only way I stopped my PDA from freezing like this was to disable the auto power off feature in Settings/System/Power and keep the backlight turned on (but lower without it plugged in) Settings/System/Backlight.
This helps with other bits too, makes the delay in the unit from ringing less and connection time faster.
Regards.
Dave.
Click to expand...
Click to collapse
Did any experts here got a solution to this? I really don't know why it happened.. I am using MDA from T-Mobile..
still no solution !!
a small update here, i've noticed that this problem does not happen if i am connecting my universal to the power charger, it only happenes if it works on battery, maybe there is sensor or so needs to be replaced ..!!
i am wondering, is it a hardware problem?
do i have to replace my universal ?? or maybe there is something to do with the software or bootloader?
SomeOneCares said:
still no solution !!
a small update here, i've noticed that this problem does not happen if i am connecting my universal to the power charger, it only happenes if it works on battery, maybe there is sensor or so needs to be replaced ..!!
i am wondering, is it a hardware problem?
do i have to replace my universal ?? or maybe there is something to do with the software or bootloader?
Click to expand...
Click to collapse
Um.. Today i tried to "tick off" the battery off option under the "System" page.. it works fine for the entire day.. And battery eats up is just normal. Anyway.. I think it's related to some software conflict of resources but not hardware.. um.. at least, this is one of the solution!
UP
SomeOneCares said:
still no solution !!
a small update here, i've noticed that this problem does not happen if i am connecting my universal to the power charger, it only happenes if it works on battery, maybe there is sensor or so needs to be replaced ..!!
i am wondering, is it a hardware problem?
do i have to replace my universal ?? or maybe there is something to do with the software or bootloader?
Click to expand...
Click to collapse
any solution
Ok, it's tarted 2 days ago, suddenly my new exec screen going to blue (Like PC)??? just blue color (Sometimes white and black stripes) and hung, so I just restart it. But today, is terrible,its happend 6 times. Tonight the worst thing happend, blue screen come again but this time with soft reset, not help at all. Every time I soft reset the splash screen comes, and then that blue screen again. It happend about 5 times, the machine finally start but can't read my sd card and I try to do soft reset but screen goes and never come back. My exec didn't start at all. I tried to release the battery, leave for few minutes and put it back try to start it, nothing happend... now my exec has die.
Anyone please help me and advice please,
What I did just cook ext ROM (So it have autoconfig for my country's operator, and upgrade the radio to 1.14.10 from T-Mobile, like I did to my alpine but it have no problem until I sold it)
Whoa... help me bro...
Thanks in advanced
Finally it's start but never reach windows screen, the blue screen appears again.
And I remember, the strange thing, my IMEI that I read from device properties is: 355195002465655
But, the IMEI at back body,(Under the battery) : 355195000360361
Why?And what happen?
guess u have the same probs as some others
http://forum.xda-developers.com/showthread.php?t=291986
oops:
saw u r already i that post.......
OK, I've got the same problems as you did. I was so upset with the device that I hit it on my lap (with the battery clip side hitting my lap) and then put the battery back on. Then it turned on! So everytime I have this problem I just hit the battery clip side and it turns on like 70 percent of the time. I just realized the SD card is on that side...hmmm..must be something to do with SD. I'm pretty sure someday it would just stop working at all if I keep doing this.
I don't advise anyone doing this but so far it works for me. I still have problems waking it up though. I really think the mainboard is messed up so I'm trying to get a mainboard, even a broken miniusb mainboard just to test it out. I opened mine up to the last screw and no loose connections noted. So if anyone has a mainboard then can sell me PM me.
If you still have warranty on the device, I advise you to send it in for warranty repair. It seems to only get worst and not better. Goodluck, hopefully we can find a solution for this. If I do get a mainboard. I'll let you know if that fixed it.
Hmm, I've guess it, I think the pprob is mainboard. I'll send it for warranty, (But I bought it in other city not in my own city) So i'll have to send it then on friday this week i'll go to that store to check arround and maybe choose the best product. I'll give the update then.
Anyway someone can give a advice to choose the mainboard?
Thanks in advanced.
bump..we need help..Is it a mainboard or coaxial cable problem? Please advise..
OK, Problem found.. Thanks Corneluis...It is a problem with the voltage control on the mainboard! Anybody has a workaround for this?
SOLUTION FOUND!!! At least for my Jasjar. Thanks, cornelius about the info on faulty voltage control which causes the Bulverde CPU to hang and give funny lines and colors to the screen. The solution is to install Pocket Hack Master and disable the Device CPU scaling in settings and set the speed to 312mhz for standby and before you turn it off. Now you can always clock it to 520 when needed but before you turn it off or close the screen make sure the speed is only 312mhz.
This has worked for me for more than 24 hours without any sngle hang.
Hello All - My universal seems to crash when my battery power gets to around 65% and then wll only come on when plugged into a power source. Is this a dodgy battery or something else.
Also, what would be the the things that you would do to make it more stable?
Please help... I see a lot of thread go without no replies, so please help me if oyu can...
I am new to PDA's and have only had it for a week.
Many thanks.
Jimbo.
When you say crash can you please describe exactly whats happening?
Is it freezing, simply switching off or something totally different?
Ta
Psi
You go to do somethinig with the phone, like make a call, and the whole thing goes blank, so I press the power button and it seems like its booting up againn, but when the WM5 is about to start it goes off again.... This seems to happen a lot when the battery is around 65%.
If I then plug it into the power source its okay....
Battery is knackered mate. Replace it with a new one and you'll be fine.
Psi
I have just got the HD2 and been using it for a few weeks. Downloaded a few apps (eg HTC rom, BSB tweeks) and all is good. Saw Max Manila and looked like a great idea - checked my manila version 2.5.19211619.0 and downloaded 2.7 SE (checked it's right for my manila) loaded onto phone and it crashed after soft reset. Took battery out and phone doesn't go past first screen (with the red writing bottom left) - Hard reset is the same and now I'm worried!
Any ideas???
sad to say yy sounds like hard reset time.
power off, hold volume up and volume down, tap power keeping volume up and down pressed til the screen comes on and follow the prompts.
it will reset your phone to factory defaults.
never used max manila so I cant help with what the problem might be, but if there is a developers thread for it you might be better asking there.
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
if your phone is provider locked then that will not work.you need the rom that came on your phone. so if was from uk o2 then you need the o2 uk rom, otherwise it wont work.
No luck! Whilst I've got everything to sort the phone out it won't do anything but load the white first screen no matter which buttons I hold down.
Man this sucks!
Guess there's nothing for it except the bin unless anyone else has any other ideas??
can you get into boot loader?
press and hold vol down(not up this time, just down) tap and release power, keep vol down held. should boot to striped cultures colored screen.
if you can what does it say next to SPL?
Hi Samsamual
Thanks for helping but no, won't go into bootloader either - doesn't respond to any input (even when I conect the usb the charge led doesn't come on!) and just starts with the white screen with the HTC logo and then the red writting appears and it just hangs - left it for 5 mins just to be sure and no change
Looks like I've really messed it up although I have no idea what I did wrong - instal went just like the other things I installed.
Ahh shame. All i can suggest is the original rom sd card method. But it MUST be the propper rom that came on your phone, so if you got it from vodaphone, , , even if it is unlocked, you must use the voda rom.
Also, have a really good read through the pages in teh rom development section. If you can find someone with the exact same issue, you could be one step closer to fixing it.
Brotherskid said:
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
Click to expand...
Click to collapse
you must tab the power botton for a short time just tab it and leave it with keeping pressing on the volume up and down buttons don't leave them i think it must work with you tell me if it works
Brotherskid said:
...I'm going to try booting from the sd card b
Click to expand...
Click to collapse
When you tried the SD card method did you use a 2GB SD card and was it formatted to FAT32?
WB
Have you tried a boot (all combinations!) without the sd card installed?
Hoss and WB - thanks for the comments
Hoss, I've held the volume buttons for over a minute after powering on - no change
WB, I can't get the phone to go into boot loader screen but thanks for the info for the future. Next time I'll see if I can copy the original rom just in case.
Resigned myself to having a new paper weight on my desk and looking for a new phone - Guess I won't be putting so many programs on my new one....
PA - Thanks for the advice - Yes tried with sd card in/out sim in/out bootloader, hard reset, soft reset and always the same.
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
rlydiard said:
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
Click to expand...
Click to collapse
What's most annoying is it wasn't as if I was doing anything crazy! Max manila is used by many people (from what I've seen in the threads) and I guess I downloaded the wrong one (although naturally I checked and it's the right one). Certainly will curb my using of 3rd party software! As for the warranty, you're right, I can try and see if it can be fixed (bizarrely, that hadn't occured to me - I thought that with no resets working HTC couldn't do anything). Thanks for the tip and I'll let you know how I get on.
Surely your warranty will cover this. Yes, let me (and us) know how all of this goes. You will get your phone back to what you deserve, for sure!
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
watnuweer said:
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
Click to expand...
Click to collapse
Experential nut I may be, but just wondering if you had the problem after you installed the MAx manila? I wonder now what versions of OS may be causing this problem.
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
fakker said:
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
Click to expand...
Click to collapse
This is getting more interesting, what do you suppose is the cure of taking out the battery, and then charging? I do not doubt your experience, I am just extremely curious if anyone can explain this phenomena.
Hi there,
i have search but can't find anything
A friend of mine just gave me HD2 and i was super excited about it.
The phone wasn't used for ages so i plugged it for 10 minutes and while plugged i tried to turn it on.
the phone started to vibrated continiously without displaying anything.
I removed the battery, unplug power, inserted battery again and it just vibrates like nuts
Once out of 5 (roughly) it flashes... the flash and then vibrates... again nonstop
once out of 10 (roughly again) it just doesn't do anything at all.
even when plugged to the power, no led or nothing.
did i get a dead beast ?
I tried, holding buttons, pressing reset button, etc but with no luck...
hope you guys could help me... many thanks in advance
Check the battery pins on the HD2 and make sure that non of them are bent slightly or anything like that. A slightly bent battery pin can cause the HD2 to do some crazy things. If non of the battery pins are bent then you might just have a bad NAND chip and the only fix for that is a new main board.
Nice bike in your avatar pic too by the way.
just checked them all out and they are well aligned and don't seem to have been touch
that sucks
Cheers for my ride i like it too ^^
cheers,
i just checked them all and they all look just fine
sound like i am fu**ed am i ?
Cheers for the ride I like it to, a least it works
wuub said:
cheers,
i just checked them all and they all look just fine
sound like i am fu**ed am i ?
Cheers for the ride I like it to, a least it works
Click to expand...
Click to collapse
Dang man that does suck, I hate to tell you, "Yeah it probably needs a new main board.", and then someone else come up with another idea. But I do think that is going to be your fix. i say this cause if it was bricked it would more than likely vibrate one brief burst and that would be it, nothing else. but the steady vibration sounds more like a bad component on the main board. Sorry friend that is my opinion. Maybe I am wrong though.
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
wuub said:
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
Click to expand...
Click to collapse
keep the volume down button pressed then swutch on your phone ...if you go into a tri colour screen ..then you might be in some luck ....then you have to go to the official htc site and download a rom update from there ..and flash it ....
i tried but nothing
now it's just dead...
i plug in it so maybe it will charge the battery normally but it doesn't seem to to anything. normally there is a led indicator no ?
wuub said:
i tried but nothing
now it's just dead...
i plug in it so maybe it will charge the battery normally but it doesn't seem to to anything. normally there is a led indicator no ?
Click to expand...
Click to collapse
orange led will glow ...when plugged in ....maybe your friend tried to flash android on it but didnt succeed thus causing phone to not charge ...or maybe it is a serios hardware defect ...you can buy replacement motherbrad from here http://www.ebay.com/itm/Mainboard-Motherboard-HTC-hd2-leo-T8585-/260819122167?pt=LH_DefaultDomain_0&hash=item3cba07f7f7#ht_500wt_969 take it to your local repair shop and tell then to replace it ....try this if there ar no more hopes there are cheaper boards avalible too on ebay search...be sure to buy this mbd ...only if your phone is non T-MOBILE
wuub said:
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
Click to expand...
Click to collapse
Yep it sounds like a bad NAND chip. My guess is it has bad blocks that is keeping it from booting and the steady vibration is being caused by the same. Again just my opinion. I say this because it said, "/!\ Software update failed. Please Try again.", this is common in cases when the NAND went bad.