hi
i think i brick my htc hermes 200
i was trying to fix "No GSM" but during the way it shut down
i follow thread on wiki - problem 5
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
when it came to unlock my device was in bootloader I run the unlocker but my device turn off and now only shows the 3 color screen but with no light and no letters like info herm200 IPL-1.01 or serial or usb when i connect usb cable.
my device was
herm200
IPL-1.01
herm200
SPL-1.40.olipro
now i cant connect i try almost every thing but doesnt work
any sugestion ?!
did any one had this problem?????????
can any one provide an sdcard flash rum ready for me just to copy in memory card?
Have you tried a hard reset? If you are able to get device into bootloader as you say, you can flash another rom as well. Connect phone to pc via usb cable (bottom of bootloader should change from 'serial' to 'usb') and then flash rom. Obviously you need either HSPL or USPL on device first
first of all I'm very grateful for reply.
my problem is not like usual i been reading on wiki ore in forum.
my device get in bootloader but doesnt shoh light on the screen and doesnt show letters no info or serial/usb just shows the 3 color with no light on it
hard reset doent work
Obviously you need either HSPL or USPL on device first
Click to expand...
Click to collapse
can you provide for me I dont know where to find and what are they
ubejd said:
can you provide for me I dont know where to find and what are they
Click to expand...
Click to collapse
HSPL info can be found in the upgrading section in the wiki or in this sticky
Related
I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
it wasnt dead...
thanks to this forum!!
m_carleone82 said:
I had a wizard and trying to fix it.
When switch on, blue cingular screen appears and show ipl spl gsm os numbers.. and halts on.... it stays like this...
i enter RGB screen it says ONLY `ipl 2.25 spl 2.25` ...
when i connect it to usb.. USB text appears but when I try to install `love ROM` RUU says, it is not connected check computer check usb cable.. so it is invisiable for computer but in device manager it s shown as winCE syc device when I connect..
do u think it is bricked.. Or theres some to do....
thanks
Click to expand...
Click to collapse
Hi,all,i have this problem........ipl 2.17 spl 2.17....please help.......
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
starkwong said:
m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM.
Click to expand...
Click to collapse
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
ichiban said:
Hi Starkwong.....i have the same problem .....can i reflash to original rom even my MDA is not recognized by my PC?.....thanks for your reply
Click to expand...
Click to collapse
Yes ! if it gets into Bootloaders mode(tricolor screen) with ipl/spl display and when hooked up with pc via usb,a small usb appears at the bottom of the Bootloaders,it means it has connectivity with the pc,You can flash the official rom in the Bootloaders.
ahhh, hardreset. the pumpkin in my eye.
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
hugomalheiro said:
"m_carleone82:
press Camera+reset to enter RUU mode, then flash with Cingluar original ROM."
I´m right now on the RGB screen , and how can now put the original ROm????
please help me
thx
Click to expand...
Click to collapse
While in Bootloaders (RGB) screen,hook up the phone with pc via usb cable,watch small usb appear at the bottom of the Bootloaders,run the RUU in the Rom you downloaded,follow the instructions,it'll start to flash.let it finish and the phone will reboot.
Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725
I have a ogange SPV M3100, when i torn it on i se 4 stripes, red, green, blue and white stripes. on red i se text :
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
What i need to do?
Can some one help me?
Sory for my english!
That is the bootloader screen. Just soft reset the device with the stylus and it should boot up normally, if the device is OK. If you are not sure how to softreset, check the WIKI here:
http://wiki.xda-developers.com/
If it doesn't go past there, there is still hope. Read the info in the WIKI on how to unbrick your phone. Based on the SPL version that is on the phone, someone has already been playing around with loading roms, as that is not a factory standard SPL. Much better, but not factory version.
Reply back with your findings after the soft reset.
Nothing hapans, its stil the same, screan with 4 colors.
I tryed hard reset an soft, but nothing.
How to instal a new rom?
OK, a couple of questions.
1. do you have the usb cable to connect your device to a pc.
2, do you have access to a pc with activesync installed that has usb ports.
3. do you have a micro sd card and a device that can write to that card.
Your answers to these questions will determine the path we need to take for upgrading.
Will try to respond as soon as I see your posting.
Steve Sharp said:
OK, a couple of questions.
1. do you have the usb cable to connect your device to a pc.
2, do you have access to a pc with activesync installed that has usb ports.
3.
,0
Your answers to these questions will determine the path we need to take for upgrading.
Will try to respond as soon as I see your posting.
Click to expand...
Click to collapse
At firs i flashed my m3100, pocket pc is working, but as a phone it dont works, phone is swichin off him self.
1. Yes, i have a cable
2. Yes, i have access to a pc with activesync installed that has usb ports. But it is not connecting to a activesync.
3. Yes, i have a micro sd card and a device that can write to that card.
I flashed my device with micro SD card!
I think the phone is broken.
steks84 said:
At firs i flashed my m3100, pocket pc is working, but as a phone it dont works, phone is swichin off him self.
Click to expand...
Click to collapse
so that it all clear, do you mean to say that you m3100 boots up fine, but you cant make calls?
or
your m3100 keeps resetting itself
or
basically, what exactly do you mean by pocket pc work but phone dont work.
anyways, just reflash using your microsd again, and you *should* be fine
XtreMe_G said:
so that it all clear, do you mean to say that you m3100 boots up fine, but you cant make calls?
or
your m3100 keeps resetting itself
or
basically, what exactly do you mean by pocket pc work but phone dont work.
anyways, just reflash using your microsd again, and you *should* be fine
Click to expand...
Click to collapse
At first, hi don not offer me to write in may sim pin code, then hangs on and shows white screan, then phone buton dont works and hang down buton too.
I have flashed my M3100 several times an several rom versions, but the same!
you can try reflashing your radio, or checking your device for bad blocks with mtty
edit:
just saw this link over at the upgrading subforum
http://forum.xda-developers.com/showthread.php?t=377389
just exactly what you need for checking bad blocks
Ok, i will try to check for bad blocks, and let you know about situation.
Can someone give me a link for radio files?
Dude, try the wiki : radio roms....
I need some help!
I have a dopod C800. I have tried upgrading but have run into some difficulty.
The PDA will not go past the tricolor boot loader screen. The only writing is as follows. In the Red section.
RUU
IPL 1.09.0001
SPL 1.09.0001
I cannot get the Active Sync to go green (connect) but I know my computer can see the device as i get a sound when i plug the USB cable in.
Can help me and advise what I can do? I think i might have tried to HArd SPL.
Need help to unbricked herald
i have the same exact problem. some people say the phone is bricked.
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
i found this link, that shows that hermes can be fixed. Is there any justice or expert guru to get our phone unbricked
I went try to repair it and they say i gotta change the motherboard aka the machine. i was like ^&* since it cost $400, might as well by a new phone.
Hey im new here! *in terms of posts and stuff*
But I got a big issue..
I was trying to upgrade my HTC Touch from windows 6.0 to windows 6.1. And the phone went funny and the USB cable stopped working and disconnected before it could upgrade? So now, The phone is stuck in “Bootloader Mode” and I don’t know what to do?
I am supposed to install a ROM (Official or otherwise) to make the phone better, but for some reason the ROM cannot detect the phone?....but its odd because the USB is being detected by sections of my laptop...for example, when I connect it, the Safety Remove Hardware says "PocketPC USB Sync"...but if I connected it to a USB Hub for example, it wouldnt detect it?
and my Touch also has the USB at the bottom *on the white screen*...yet, no ROM can find it?..
I have these random two numbers on the screen as well “IPL 1.16.002 and SPL 1.16.0000”..? oh and RUU on the top right hand corner on the red..
Can anyone help?
Thanks..
Oh, and I know tons of these posts have been done before..but, I cant find any that talks about *my* situation..in terms of the fact that ROMs cannot find the Touch...so hence I get the 264 Error all the time...
First of all, are you attempting to upgrade an Official ROM from HTC or one of the custom built ones on XDA here?
Secondly, if you ARE flashing a custom built rom and you don't know what IPL & SPL you're in trouble. There's a few stickies in the Upgrading forum about these, you must flash a USPL or HardSPL before your phone will let you put a custom ROM onto it.
I am having the same problem.
I just used the USPL to unlock my CID ( now my g_ckeyCardSecurityLevel = 0) but now my phone just show the logo's screen and turn off. I can't dump any rom on it since the communication with ActiveSync doesn't exist.
Any clue?
thanks