Related
Hi
My XDAII doesn't start as it just hangs at first boot screen and nothing happens there after. Sometimes charging takes place and sometimes, it doesn't charge while plugged with a wall charger.
Any suggestions for this problem?
ya, I can put this ini bootloader mode and I have tried a no. of diff. ROMS (WM SE 2003 and WM5 as well).
Help
yes this is exactly whats happening to me I have a lovely functional XDA 11 which works like a charm THEN I bought a second on EBAY (Stop laughing !!) which sometimes boots sometimes doesnt - sometimes it even starts and goes all the way and functions for up to a few mins then freezes and has to reboot and is then dead as a mullet!! I take the battery out and wait a while and she starts sometimes again sometimes take a few attempts - Help any theories?
I have exactly the same problem with the blank white screen after the o2 splash.
But in addition, I get screen flicker and fuzziness on the occassion that I DO get it to work (after leaving the battery out all night).
same problem i am with u
Hello brothers. I have same problem my o2 xda IIs please give me a solution
First time i have hangup problem then i tried upgrade 2k5 upgrade successful.Then i have same problem is it softwere problem or hardware please tell me
It seems like this bacame a problem for a lot of people - something similar started hapening to me, too ... At first it was scarce, but now it is impossible to use it as a phone - it hangs to many times... I suppose it's a hardware problem ...
need some help
Hey guys my O2 XDA 2i is not starting. It shows the welcome screen and the screen alignment . and you keep aligning the screen for ages to see nothing happning. anybody has a solution.
I also have a Imate pocket PC, but it works better than O2 XDA 2i. no problem from last 3 years
Thanks for all your post, I have the same problem and now it has been sorted!
my xda also don't starts windows and it all started when i run doc partition tool on wm6.so i managed to install wm2003 and it works fine try downgrading to wm2003 and you will see the difference that your device will never give you that problem again
Have u had a think?
Du think there might be a virus?
All i can recommend is to upgrade the rom
Hi, I have a problem with my Cingular 8125. See my touch sreen is not working and I just flashed my phone. Now I am at the part where it tells me to "Tap the screen to set your Windows Mobile based device." Since my touch sreen is not working, I can not touch it, well I did but it does not work. Is there any other way I can by pass this? Any help is really apprecited, thanks in advance.
why not install wm6 standard rom without (touch screen)
If can provide the link, I would really apprecite it and also I tried flashing the ROM with WM6 but I have Vista. I followed all the steps in how to update ROM with Vista but it doesn't work. Everytime I try to flash the phone, it says "ROMUpdateUtility MFC Application has stopped working" and I can not seem to find any solutions .
PLEASE NOTE!!! SMARTPHONE(Non touchscreen) AND POCKET PC ROMS ARE TWO DIFFERENT THINGS! YOU CANNOT FLASH A SMARTPHONE ROM TO A POCKET PC!
I tried flashing the Cingular 8125 with a WM6 ROM, and that doesn't work. I couldn't find any ROM that has the touch sreen disabled . Is there a WM6 for Cingular 8125 that has the touch sreen disabled? If anyone could help me, I would really apprecite it.
- Thank You...
aiq said:
Hi, I have a problem with my Cingular 8125. See my touch sreen is not working and I just flashed my phone. Now I am at the part where it tells me to "Tap the screen to set your Windows Mobile based device." Since my touch sreen is not working, I can not touch it, well I did but it does not work. Is there any other way I can by pass this? Any help is really apprecited, thanks in advance.
Click to expand...
Click to collapse
If your touch screen doesn't work I don't know how much use the phone will be for you but to get past the spot your in at this stage of your install you can always use a freeware called my mobiler at mymobiler dot com or pocket controller pro from any of the usual places.
Than you for the software information, it really helped but I'm still stuck, I am at the "align screen" part, I keep tapping the target but never works.. .
I just posted this on another forum and then I read this posting. Based on what I read here, the MDA is totally hosed if you cannot use the touch screen?
Well my MDA Touch Screen has finally quit working. My MDA is almost 2 years old. Now I have a problem using the MDA since I am so use to using the Touch Screen. Has anyone tried to use the MDA without the touch screen?
If so, how did you setup your MDA? I cannot even get to the various button menu to reset all my buttons. I have been using SPB PocketPlus, SPB Diary, etc., and now I am at a loss to even get to the Menu Screen. Any suggestions will be appreciated. Thank you in advance.
All I can say is that you can try to change the touch screen or call T-Mobile or HTC to see if they will replace it for you. I just ordered a new touch screen I found on eBay and am waiting until it comes so I can replace it and see what happens. If you are having software problems, I am not sure what problems you are having, you can try to re-flash the MDA with the newest MDA ROM or a ROM on this site...
Hope it helps
I had the exact same problem you had, and I finally came across a solution on a different site.
All you need to do to bypass this is connect your phone to your pc (usb activesync) and browse the contents on your wizard and delete \\\Windows\StartUp\Welcome.ink . Then soft reset your phone and you are past the screen calibration part and continuing the installation
A Little Late
I had the exact same problem you had, and I finally came across a solution on a different site.
All you need to do to bypass this is connect your phone to your pc (usb activesync) and browse the contents on your wizard and delete \\\Windows\StartUp\Welcome.ink . Then soft reset your phone and you are past the screen calibration part and continuing the installation
Can you tell me how to find this file? I've connected my 8125 to my PC, but did a search for the file and it's not found. If I can bypass the screen it would at least be able to be used. I appreciate your help. Also, using My Mobilier doesn't work if you can't tap the screen as I tried it.
My Touch2 was purchased on 16-Nov 2009. It experiencing intermittent self-power off problem when phone was left ideal for couple of second! I believed it was referred to many as Standby-of-dead (SOD) problem.
Secondly, the phone "freeze" intermittent when charging with power adapter.
For both cases, the phone cannot be turn on via the Power button. Must perform manual Reset to power on the phone each time.
I performed FACTORY Reset 5 times already; disabled the Touch2Flo; disabled ALL auto power off; disable auto switching of Band.. yet none of it resolve the problem. I feel like throwing the phone against the wall many times!!
Any expert views highly appreciated!
[ROM Version: 1.28.707.3 (66092); Radio Version: 3.49.25.05; Protocol version: 61.42t.25.31H]
##UPDATE: I logged a problem ticket with HTC Service center at Malaysia 2month ago. The service center called and they offered to change the motherboard. I had it changed unfortunately the problem still persist. And worst still the touch screen didn't not respone after a while. I sent to fix and waited for another 2weeks, and they changed the 2nd motherboard. (It's under warranty thus FREE of charge!) I'm been using the repaired phone for past 2monts WITHOUT any intermittent power off issue.. YIPPI!
P/s: My batt Serial No: 1GKA299KQQ4912. Part No: 35H0015-11M. The HTC repair report did not mentioned whether they change my batt nor I cannot confirmed whether it was the "-07M". Anyway, I'm glad that my nightmare is over for now
Do you mean a "hard reset" when you mention "factory reset"? If that did not help.......my suggestion would be to send it to HTC service......
Success...
Same Problem
Same problem here. first it happened 1 time a month but now it happenes 2 times a day.
i have newest htc rom
i think it has something to do with the sms. when i wrote much sms so that history has over 200 sms the boot sequence and every thing is very slow for about 15 minutes.
someone else got same problems?
Description I have recently bought a new htc touch2(special Version) phone with 8GB SanDisK microSD. . the problem i'm facing is that when my phone's unused for a few seconds and it goes into standby , it does not come out of that mode.... The only thing that can be done after that is a Hard Reset . . . . .also the volume rocker does not work in the default music player...i cud wrote 10 more bugs here . . . .kindly help me out with this issue
return the phone back and get ur money back ... if hard reset isnt workin , then it's a mechanical problem and it couldnt just be fixed with soft fix or somethin like that ...
get a real Touch2 , not some special editions which have bugs like urs !
The same is happening to me, but I realized that if you press power button and wait aprox 60 seconds the screen turns on. Obviously this is not useful.
i had the same problem. phone refusing to come out of sleep mode (screen would not unlock) found a fix on the htc official web site called:
(Update for HTC Touch2 – Owner Information )
and all is ok now. hope this helps
My experience...
Please take care of your battery! Especially the way you charge it really matters.
Better always charge with an official charger.
andyrew said:
i had the same problem. phone refusing to come out of sleep mode (screen would not unlock) found a fix on the htc official web site called:
(Update for HTC Touch2 – Owner Information )
and all is ok now. hope this helps
Click to expand...
Click to collapse
I updated my touch2 two days ago and worked
But five minutes ago it turned off again i ll call support support service tomorrow and post the answer..
Got the same problem. Russian dealer says that it is the accumulator's fault. What is the S/N of accum on problem device? If it ends with 35, that is the problem. Good accums goes with 07M end of S/N. Try this, many people solved it so. I'm waiting a new accum too
Try recalibrating the battery:
By completely discharging it and then charging it to the full with phone switched off. I do not know about Mega but it worked for my Gene.
Also, that unable to wake up from standby problem will be solved if you install the personal information update from HTC and in the lock screen mode, choose windows classic instead of the default mode.
I faced this issue once and solved it. After the update though you can use the default lock method (slide to unlock)... looks like HTC got the idea from S2U2
I'll bring my phone to dealer today. Hope they will change to another one or will do the moneyback
Service says that trouble is in the battery. "Bad" accum S/N ends with number 11, "good" - with 07. In 3 days I'll take my device back with new accum and we shall see)
I've heard something like that in relation with some SIM.
Alarm:battery
I am sure that the problem described should be related to shoddy batteries.Try change one (better non-official HTC),and it would solve the bug. I say this totally thru my own long pains-taking experience. Believe me!
I've also got this problem. And what's worse, I read on the internet that many more (older) HTC devices cope with this problem. I've just done a Hard Reset and i'll check whether it works now.
I hope I do get a working one if I send it back to the store :s
simPlexicallity said:
I've also got this problem. And what's worse, I read on the internet that many more (older) HTC deviceS cope with this problem. I've just done a Hard Reset and i'll check whether it works now.
I hope I do get a working one if I send it back to the store :s
Click to expand...
Click to collapse
Can you tell me where did you read this?
Dunno but a week ago I searched with google on 'HTC turn off', 'HTC screen off' & 'HTC turns off automatically' etc. You will find many hits... (only winmo phones though)
This is Major issue , i got Touch2 a few days back and the auto-shutdown has bugged me many times.
My vendor asked me to reset the phone, after reset so far i had no problems of auto shutdown,
But when i plug the USB into my system attached to phone it shut downs
I'm having same problem with same feelings
has anyone managed to resolve the issue.. I've tried latest rom, even customized ones but no luck..
DrJason said:
My Touch2 was purchased on 16-Nov 2009. It experiencing intermittent self-power off problem when phone was left ideal for couple of second! I believed it was referred to many as Standby-of-dead (SOD) problem.
Secondly, the phone "freeze" intermittent when charging with power adapter.
For both cases, the phone cannot be turn on via the Power button. Must perform manual Reset to power on the phone each time.
I performed FACTORY Reset 5 times already; disabled the Touch2Flo; disabled ALL auto power off; disable auto switching of Band.. yet none of it resolve the problem. I feel like throwing the phone against the wall many times!!
Any expert views highly appreciated!
[ROM Version: 1.28.707.3 (66092); Radio Version: 3.49.25.05; Protocol version: 61.42t.25.31H]
Click to expand...
Click to collapse
I am a Noob , and do not know much about the expert stuff most of you guys write about. Please help me solve a problem which I am having with my T-Mobile USA HD2 which I am using in Qatar.
It used to work well without any problem until yesterday when I was trying to load some of my old software (calligrapher, bridge, chess etc which I had purchased for iPaq a fewyears back). The bridge and chess worked fine, but after loading the old version of calligrapher, the screen froze. Soft reset 'red' button did not work, so I did a hard reset using volume control+power button and reloaded earlier software except calligrapher. The phone has started working again, but I started frequently getting an error message stating that "there is a problem with DocumentParser.exe" .The HD2 tries to connect to the Microsoft server, but then the screen freezes. I have to remove the battery and restart, but the suddenly when I am in the middle of something, the screen freezes again. There is a 593kB "DocumentParser.exe" file in the Windows folder of the phone. Will the problem go away if I replace this with another (maybe non-corrupt) file? I did a google search, but could not find the file on the net.
Can anybody please help with finding the file, or maybe suggest another solution?
Your advise will be greatly welcome.
Thanks and Regards
Today I installed ROM version of Artemis 23 Artemis before I had everything, I turned the phone had a bug at first, then worked normally until I installed a few applications [Core player, Nimbuzz, skip, etc.], they and was using before.
But here the problem started big ??????????
After a reboot would not work.
Opens and stuck with HTC logo, quietly brilliant,
ROM is the first installation, first read on this forum a few days and after that install.
Generally this problem is wireless, but I had compatible radio.
Please, HELP? I do not know what to do,
I tried hard reset and nothing, it also found no computer, no longer enter bootloader.
Waiting for answers and help !!!!!!!!!!!!!
similar sounding situation, both using artemis.
see HERE
you two should both post in the artemis rom thread.
samsamuel said:
similar sounding situation, both using artemis.
see HERE
you two should both post in the artemis rom thread.
Click to expand...
Click to collapse
+1 beat me too it sam, just finished reading the other one, was gonna suggest the same thing ....
Please excuse me for English with mistakes, but we managed to restart the phone without trying to use another ROM or Radio.
After three days of torment phone works now.
I try to give details for those who have the same problem.
I did absolutely nothing with no software HSPL gender, etc. SSPL.
It's simple if you run the following steps are needed even to try several times.
With the battery removed, hold the volume button and power button and immediately try intrioduceti battery [is a little harder], but all at the same time and press the red button on the back cover, the hard reset.
Will enter bootloader for a second and will soon appear blue screen with white writing that one will ask if you want to press voip [the ring], which I did the first time I reziolvat nimic.ramanand same problem, that your dead.
After several attempts and I went immediately into bootloader and white screen with blue writing but I have made VoIP key pressed opposite operation, this time defending another window through which I explain if you want to continue to restore lost all data.
I risked a few seconds after the phone started like I have made installing a new ROM, you know what operations should be further enforced, the introduction of email addresses, etc..
About the
badonyx said:
Please excuse me for English with mistakes, but we managed to restart the phone without trying to use another ROM or Radio.
After three days of torment phone works now.
I try to give details for those who have the same problem.
I did absolutely nothing with no software HSPL gender, etc. SSPL.
It's simple if you run the following steps are needed even to try several times.
With the battery removed, hold the volume button and power button and immediately try intrioduceti battery [is a little harder], but all at the same time and press the red button on the back cover, the hard reset.
Will enter bootloader for a second and will soon appear blue screen with white writing that one will ask if you want to press voip [the ring], which I did the first time I reziolvat nimic.ramanand same problem, that your dead.
After several attempts and I went immediately into bootloader and white screen with blue writing but I have made VoIP key pressed opposite operation, this time defending another window through which I explain if you want to continue to restore lost all data.
I risked a few seconds after the phone started like I have made installing a new ROM, you know what operations should be further enforced, the introduction of email addresses, etc..
About the
Click to expand...
Click to collapse
i see your from romania, plz add me : yahoo id:tothszabolcs
help i have stuck at startup,