help!!i really no idea with my devices as i try to flash it to wm6,then it stop at 50% and reboot then hang at bootloader screen,i try to flash again but when it reach 1% it will restart and update error msg prompt, it said "the image is corrupted" if im using sd card flash,it come out 00068002 on the top of the"loading" words then go in the tri colour screen again. anyone pls help me pls!!!!!!!!!!!!
Man I wish you guys would do a LITTLE research on how to flash stuff... I bet you don't have Hard SPL installed even though its splashed about all over the forum.....
Try to download the SHIPPED STOCK ROM again... It seems you have a corrupted download.
Once you have downloaded the rom, then reset Hermes into TRUE bootloader, not the failed flash you are getting.
On the PC, untick "Allow USB connections" in active sync the connect Hermes.
Double click on RUU_Wrapper.exe of the freshly downloaded rom. Follow prompts...
Pray......
Then, if it works, INSTALL HARD SPL V7...........
thanks for rely brother,i hv tried download a shipped rom from here and i hv follw all the prosedure u thought,it still doesnt works,oh no....................
Error 226 flash write
Hello friends i'm italian and sorry for my english.
I have a problem with my hermes200.
I have flashing on my tytn a rom kitchen using "package tool by bepe" with nb IPL, SPL, Mainsplash, Subsplash, ExtROM and GSM extrated from original rom htc tytn wm6 and a OS.nb extrated from rom kaiser ITA wm6.1.
When the flashing is termined the hermes don't start: push power botton but the screen is black and only green light is ON.
I have flashed original htc hermes wm6 but i have "error 226 flash write" when the process is at 89%.
I have IPL-1.04 and SPL-2.04. CID.
SPL 2.10, SPL 2.20, SPL 2.30 are not possibile to install.
i have try command with mtty tool:
- task 32 -> FF
- task 28 -> format storage success
- task 2a -> fix bad block
- info 8 -> much bad block Os Win CE
I've try to reflash the original rom but the problem is the same
The battery don't possibile to charge and level should be of 40%.
Help me please....
Tanks!!!
Hi there,
Hope you can help me...
Since i bought my Cruise, I flashed it to the newest ROM version of HTC and it automatically installed SPL 3.13 with.
The problem is that if I want to install the WM 6.5 rom, I have to "Downgrade" My SPL version from 3.13.0000 to 2.20.
I followed the steps explained by "Olipro", but when the upgrade starts, RUU kills activesync (seems to be normal) and when the phone normally reboots in bootloader mode (like when you flash a new rom), nothing happens. The phone didn't shutdown and tries to establish a new USB connection !
I tried to turn manually the phone in bootloader mode on to force the SPL update, but the % bar stays at 0 and RUU returns a communication error (262).
I tried also to install the wm 6.5 rom without install SPL 2.2, but it crashes (stays @ 0% too)
I don't know how to install this stinky version of HARD SPL.
Heeeellllpppp !!
NOTE : I tried with or without µSd, does the same thing.
Thx
hmm try disabling firewall and antivirus one of them may be blocking the connection. Thats my only thought about it.
Thank you for the answer but it don't work...
Nobody can help me ?
Try to extract the files from the newest htc rom to a new folder, and then copy the "RUU_Signed.nbh" from the SPL V2 folder to the extracted files (to the new folder) and run the "ROMUpdateUtility.exe" from the extracted files (from the new folder).
nope ...
Please, consider my asks...
I know there is necessarily a solution but I have not yet found.
I don't know where/why it is crashing.
What does the HTC need to downgrade the hardspl ?
Is there a protection that can't be bypassed with the 3.13 ?
The only thing that I can do atm, is flashing the official HTC rom (useless ^^).
The actual version of my rom is :
_HTC Touch Cruise_RUU_Polaris_HTC_FRA_3.13.406.0_radio_sign_25.85.30.07_1.59.42.15_Ship
Thanking you in advance...
Pixel69 said:
Please, consider my asks...
I know there is necessarily a solution but I have not yet found.
I don't know where/why it is crashing.
What does the HTC need to downgrade the hardspl ?
Is there a protection that can't be bypassed with the 3.13 ?
The only thing that I can do atm, is flashing the official HTC rom (useless ^^).
The actual version of my rom is :
_HTC Touch Cruise_RUU_Polaris_HTC_FRA_3.13.406.0_radio_sign_25.85.30.07_1.59.42.15_Ship
Thanking you in advance...
Click to expand...
Click to collapse
HSPL 3.13? In this ROM is ver. 3.13 drivers, not HSPL... If you have original ROM and you dont install Olipros HPSL, you have original HTC SPL...
When I enter bootloader mode, the HSPL version is : 3.13.0000
Of course it's the original htc HSPL.
The problem is that I can't downgrade it to the olipro's version : 2.20.
Did you try it on other PC?
2 PCs, 2 USB cables..
The official rom upgrade works fine, I dont think that the problem comes from the computer.
definite guide:
1. establish a connection with activesync via usb (orbit2 to pc)
2. start the romupdateutility provided in hardspl folder.
3. before it starts flashing, you need to also follow on-screen instructions on orbit2!!! execute jump-spl and stuff: click yes on orbit2!!
4. when the orbit2 states: Replug USB. you need to plug the usb-cable once off and then put it back to connect to your pc.
5. it starts flashing and restarts after its done.
Hi Manaaa,
I don't know what is jumpslp ??
I found it on the web (xda..), copied it in my "my documents" folder, ran it but it asks me a jump address (default is 0x00000000) and an spl (*nb) file..
What is jump spl ? What is the address to jump to? and where can I find the *nb file ?
In the olipro's hspl folder is only a *nbh file.
Thank you
I wouldn't recommend using a jump spl for our phones if there isn't one in the Hardspl Pack then one is not needed to be run.
Personally im still really confused by this so if i get it straight.
You are synced with activesync.
Run the file for Hardspl Run RomUpdateUtility.exe
Then go though. It switches off activesync.
Then what?? Exactly Does it ask you to replug the cable? Do you get the rom flash screen (with %) at all??
Also i dont think that spl flashes can be run from the booloader as it has to be a modded bootloader (jumpspl if you will), loaded by the program to be able to flash the new hardspl.
Also i know very little on this, this is as much as i understand it to be.
chris10230 said:
You are synced with activesync. OK
Run the file for Hardspl Run RomUpdateUtility.exe OK
Then go though. It switches off activesync. OK
Then what?? Exactly Does it ask you to replug the cable? NO
Do you get the rom flash screen (with %) at all?? NO
Click to expand...
Click to collapse
Normally, after killing activesync, the phone turns into bootloader mode. Mine stays in winCE and tries to establish new usb connection...
I also decided to force manually bootloader mode and killing activesync by myself.
I ran RUU again, it first checked the phone state (such as battery >50%, connectivity...)
CHECK : OK
Next step, by clicking "NEXT" on the RUU interface, the phone turns in "% mode" and the update starts but stays at 0%.
After a while, RUU returns an update error (such as 262).
Noway to flash hardSPL :'-( , v3.13 seems to be "write protected".
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
Click to expand...
Click to collapse
That is what error 262 is but really dont see why this happens either. And since you can boot into windows its not much help.
So it just wont go to flash it when you click it through, hmm
Your last resort would be to PM cmonex as she will have helped make this with oilpro. Ask and see if she can shed some light on this one. Maybe something has gone wrong somewhere (quite likely) that we don't know how to fix.
Stupid question but have you tried downloading, unzipping it again? May have been a bad dl... or unzip
Have tested it with about 10# DLs...
I PM'd Olipro, waiting for a response now
Flash back to HardSPL and don't Re-Plug
Hi Pixel,
Herewith are guide for you
1) Flash back to HardSPL and don't re-plug until end of session (5 minutes)
2) Flash back to original SPL 3.13 on this post . This original SPL for HTC Touch Cruise only
3) After you do this you cannot flash with other Cooked ROM or Shipped ROM
with different ID, unless you flash back to HardSPL
Good Luck my friend
I have exactely in the same configuration as Pixel69 with the same result.
I've tried to an other PC without any change.
Has somebody any idea?
Just had an idea what OS are you running to do it?
If its not 7 may not be fully compatible... Shot in the dark really
Dear all, my elf now can't activesync via USB.
I'd use the white screen method to flash downward to original rom, problems still there.
I'm sure the USB port had problems now.
The problems is... although I can connect activesync via bluetooth.
but I can flash rom via bluetooth.
the original come with origianl IPL 1.15 and HSPL 1.15
which I can't use the wihte screen method.
I had try install the EnableRapi.Cab & Cert_SPC.Cab,
after elf tune to white screen, my pc popup connection error message.
then fail in flash rom.
Could anyone can help me to solve it?
I checked with the tech. support. it cost me US$50 for repair...
this nearly the 2nd hand price of elf.
Please help.
If your PC can't detect your phone over USB, then you can't use the white screen method. Flashing over bluetooth is impossible, so that's out of the question.
The only way I can think of to fix the problem is by flashing from a Micro SD card. To flash from Micro SD, format the card as FAT16, copy the .nbh file you want to flash to the root of the card, and rename the .nbh file to "ELF0IMG.nbh", without the quotes. Turn off your phone, and enter the tri-color boot screen by turning the phone back on again while holding the camera button. The .nbh file should start flashing right away.
You'll need to flash either HSPL or USPL before flashing any ROMs - I'd recommend HSPL, as it's easier to use. If you forget to flash HSPL or USPL first, then YOU WILL BRICK YOUR PHONE. Good luck.
try with disable usb port fast speed first. If don't work you can create a goldcard and flash rom with goldcard sd (see goldcard thread in this forum).
thanks.
for method 1.
use "ELF0IMG.nbh" and hold down the camera key and reset.
I used before at 1.17 HSPL USPL or upper.
it doesn't work on the original 1.15 HSPL USPL.
for method 2.
goldcard sd
in the instruction MTTY,
it stated "connect the Elf via USB to ActiveSync"
So, I still can flash my elf at 1.15 HSPL and USPL.
I'm very stupid to flash back the original rom.
Seem I need to pay US$50 for this dumb thing.
btw... thanks a lot
have a HTC Athena x7500.
Im stuck in bootloader.
Wend I power on the device it goes directly to bootloader and
the screen say :
ET \ Njq
IPL - v1.00
ET \ Njq
SPL- v1.20. Olipro
USB( wend is connect )
serial ( wend is unconnect )
I dont remember what it was befor I try to flash a WM 6.5 rom on it.
It as a WM 6.1 in Portuguese Rom befor my attent.
I cannot power off the device by pressing the button but have to take
the battery.
I already try to change the rom, the SPl and put everything inside just
to try to move from were I am but no results.
Began to update but ends or in 1% or in 7% and loose the connection.
The device connects to the PC but in PC in WM device center nothing happens.
I try Win7 and also XP.
I went to HTC site to download the official portuguese ROM but there are no
ROM to download.
So I´m dead on the water.
I will apreciate very much any kind of input that take me out
of were I´m now.
I´m not a expert as you already notice.Please keep it simple.
Thank you
stuck in bootloader. Help needed.
stuck in bootloader. Help needed.
have a HTC Athena x7500.
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl spstuck in bootloader. Help needed.l is 1.10
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
J have explored ruu_signeg.nbh with notepad jai entered the signer spl 1.10 I know if c is vrait or name
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
is what I can fix this problem with mtty
so if possible please guide me
sorry for my bad Englis
thank you in advance
My email: [email protected]
stuck in bootloader. Help needed.
I have a HTC Athena x7500.
accidentally upgraded my htc x7500 WITH SSPL-Manual-x7510.zip of HTC X7510
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10.0000
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I have explored ruu_signeg.nbh with notepad jai entered the signer spl 1.10 I know if c is sure or not
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
is what I can fix this problem with mtty
so if possible please guide me
I board on my pda (cid locked)on the Spanish language HTC_304
sorry for my bad Englis
thank you in advance
My email: [email protected]
help me plaise
is that the bootloader command Herme (mtty) could walk on Advantage X7500
i had this problem and what i did to remedy it was, take out the battery, take out the sim card and the sdcard. replace the battery and turn on the device.
once it is in the bootloader plug in usb cable and make sure the bootloader shows usb at the bottom.
then try to load any rom that is for spl 3.0. they should load and get it out of the bootloader mode.
Once you have it working again then be sure and flash the proper spl of the rom that you are wanting before you flash the rom.
i tried the wrapper and hardspl as well until i just tried the above example on a whim and it worked. I hope it works for you.
CE
thank you for your answer
I board on my pda (cid locked)on the Spanish language HTC_304
Can you explain how you did
thanks
Was there any solution to this problem, I have the same problem?
is what you got the official rom spain