I recently bought a Tmobile Wing on ebay and it has been hard spl'ed as I can see the SPL as 4.70 Yang in the bootloader mode.
Is there any way to remove the hard spl and just have the original spl on their?
I saw this thread where it has instructions:
http://forum.xda-developers.com/showthread.php?t=364543
but in this thread it says to also reflash it with the original rom after removing the hard spl. It looks like the phone is running a standard tmobile rom and I do not want to reflash the rom, just remove the hard spl. Thanks.
Related
i was spl1.04 orginal and i upgraded hard spl7,
however i've check by mtty that i'm not sure supper CID yet, so i follow here instruction to become supper CID but fail.
I've download the file and put sspl in herm200 and run autoupdate, it prompt load fail.
But result i've got my spl become spl1.40olipro ???
i am just confuse that what spl i am. Do i still hard spl? if i want upgrade to hard spl 7 , do i need to back to spl mfg ->spl 1.04 ->hard spl 7?
can i spl1.40olipro->hard spl 7?
SSPL was probably your misstep.
At this point just re-flash the latest Hard-SPL and you should be fine. You'll have SPL 2.10.Olipro also be "SuperCID" without actually changing your CID.
THEN, quit hacking around and do some reading before you make your next move.
thanks that i am back to hard spl 7 now.
Im tryin' to use HARD-SPL-V7
Its asking me my actual spl version
How do i do to know my spl version?
anybody let me know please
use SSPL (unsafe) to flash hard SPL. It is actually Soft SPL. It is removed once you have Hard SPL installed.
Cheers...
I am trying to do the HardSPL upgrade on an orange spv m3100 as per http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26 I have the lates version of WMDC running on windows vist and can sync etc no problem
When i go through the process it shows current image as 1.23.61.4 When i carry on in brings upenter bl.exe on the phone. The phone then goes into the bootloader screen and the WMDC shows disconnected
The programme hows verifying the information on your hermes Then I get error 260 update error cant connect
The current bootloader says.
HERM100
1PL-SSPL by Des
HERM100
SPL-1.09.ds
Any ideas and help would be grately appreciated
thanks in advance....steve
Plz help
my phone shows following details
SPL-1.09.ds
when i upgrade to HardSPL 2.60, it does upgarde but when after restarting it again shows the same version of SPL
i am now unable to soft reset my phone
and one more problem i am facing is that my phone shows HERM200while before this problem it was HERM100
this problem arose after i tried to downgrade to MFG bootloader
before that i had SPL 2.30
plz help
fcwdadmin, as you have sspl.exe already running (known as soft SPL - 1.09 des) format 2Gb or less sd card FAT32, put the .nbh file of Hard SPL V7 on and rename to hermimg.nbh . Reset to bootloader - hold power, ok button above flywheel and reset with stylus. Follow the prompts. This should put Hard SPL V7 on your phone. ONLY DO THIS IF YOU HAVE Soft SPL INSTALLED...
Go to bootloader to check, it should read IPL - 1.04 and SPL - 2.10 oli.
You should now be able to put any rom on from the Hermes section. I recommend using the sd card method for that too.
Cheers...
the bootloader says:
HERM100
IPL-1.01
HERM100
SPL-1.04
Is that the same thing again ??
Many thanks in advance
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
ultramag69 said:
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
Click to expand...
Click to collapse
I've been trying to find help with this everywhere, but none of the steps seem to work for me. Should I consider the phone brick now cuz I can't get Hard SPL v7 on? I was able to go up to 1.40 using CID unlocker, but have been stuck since then.
Can you get the Hermes back into today screen?
ultramag69 said:
Can you get the Hermes back into today screen?
Click to expand...
Click to collapse
No brick. I was able to get to SPL 1.40 and have been able to flash other ROMs. I've just read too many posts that says v7 is the way to go for stability sake.
Download Hard SPL V7 from the Hard SPL thread, go to page 116, post 1160 of the same thread for instructions on how to install using the sd card. YOU NEED TO FOLLOW THESE STEPS EXACTLY... One thing wrong & it won't work.
Afterwards, you can use these steps, dropping the steps using SSPL.exe (Soft SPL) to install roms. I find it much easier & safer than using the pc.
Cheers...
hi guys.
my x1 front panel doesnt not work anymore.that means all my buttons are dead now.so i have to send my phone to service.I NEED YOUR HELP IN THIS CASE..please help me......
i restored my orginal os,splash,radio from X1i_GENERIC_UK_CDF1215-1832_R1AA017.but i am not sure all the spl are same version.i downloaded ruusigned_072stockspl.zip from olinex Hard-SPL for Xperia X1 - Released! thread.and i restored spl with this spl.because my phone was hardspl.....
now is my phone ready to send service?another word X1i_GENERIC_UK_CDF1215-1832_R1AA017 spl is same as olinex original stock one?because i couldn't restore orginal spl from the uk generic rom.i extracted spl with NBHUtil.exe from original rom but when i tried to flash with this spl i coudnt do it.sorry for my bad explanation.
also my phone does not get bootloader mode anymore.i Press and hold first the volume down button on the phone and then the phone power button.but nothing is happening.so i cant check my spl anymore.i am very stuck.how could i turn my phone to original X1i_GENERIC_UK_CDF1215-1832_R1AA017....
please help.thanks a billion in advance.....
I do not know if my answer is still useful, but:
With the original ROM, you restore the ROM (why do you mention spl while talking about standard ROM?!)
Then, you use the stock SPL provided in the thread (http://forum.xda-developers.com/showthread.php?t=431218) to overwrite Olinex Hard SPL with original SPL.
That's all, hoper you'll get yous SEX1 back soon!
Since then voila I install a rom for the first time I have a bug here is a picture to help you understand
It is an image that I have requests in the forum but am in all its images
More information please!
We need more information!
Are you using SPL or USPL?
What ROM did you flash?
Did you perform a hard reset after flashing the ROM?
If you're not sure about the above then read this for SPL:
http://forum.xda-developers.com/showthread.php?t=431217
This for USPL:
http://forum.xda-developers.com/showthread.php?t=462347
And this is an all round overview:
http://forum.xda-developers.com/showthread.php?t=505377
G
Edit: And this post makes me a senior member - woohoo!
Here is how I do I install rom always full of the same problem
Olinex I install 1.56 and then the official 1.56 rom 2009
The picture you supply isn't from the official 1.56 HTC ROM because it is running Windows mobile 6.5 (I can tell from the user interface). The official ROM uses Windows Mobile 6.1.
I think you need to make sure that you flashed the correct ROM and then flash the device again. After doing this make sure you hard reset afterwards at least once, preferably twice by holding down both volume buttons while powering the device on.
Also unless you have a CID locked phone that is branded eg. Orange, you shouldn't have to use Olinex HSPL and can download the official ROM from here:
http://www.htc.com/uk/SupportDownload.aspx?p_id=179&cat=2&dl_id=533
In any case you should confirm which SPL you have by holding down the lower volume button while booting (it will tell you either SPL or HSPL along with version number).
Let us know how you get on...
G
HSPL 156 OliNex and htc is a factory not orange or other
Okay, it sounds like you have successfully installed HSPL, but now you need to try flashing the ROM again (it appears to be the ROM that is causing the graphic corruption in your picture).
Make sure you perform two hard resets after flashing and hopefully this should solve your problem...
Cheers,
G
P.S. Make sure you back everything up prior to re-flashing as you will lose everything in phone memory (SD card should not be affected, but my advise would be to remove it anyway until you have re-flashed).