Related
Hi,
Hp just released an update for the 614, only for englisch.
I have a german 614
I dont care about the OS part since I use a cooked 6.1.
But the update also contains a modem / radio update to version 0.88.
Currently out there i think there are 0.77 and 0.81 depending on language.
I believe the radio fw is language independent when it comes to functionality. But the hpruu says wrong language.
With the current universal hpruu tools you can only update the OS which is of no use.
I know you can update the radio by booting with the key combination:
lower left key on the side (record button) and the camera button.
Then turn on ... it shows : SD loader for modem
(similar on how you update the OS)
I also know that the radio update files are in the update.
They are called
amss.mbn
amsshd.mbn
maybe also partition.nbf
But I am not sure about this.
It might work with just copying the file to a non HC SD card and using the key combination.
There might be some file renaming involved.
I someone out there to try that and let us know how it worked ?!
Thanks
sax
hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull
Saxon,
File partition.nbf is for IpaqFileStore update.
Maybe you should try with the following way:
- extract the whole package from HP side
- remove from the obtained directory the OS file (the larger one)
- put your device into SDloader state (voice recorder + mute + power on)
- connect your device into PC via USB
- launch RUU utility
In my opinion there is a big chance it will work.
Such way (using the SDloader) was working for one polish case where the upgrade of firmware failed due to PC crash. The only chance to flash again was to use SDloader + HP tool.
Good luck.
Z!L0G80 said:
hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull
Click to expand...
Click to collapse
I used the qpst already and it worked that way that i could upgrade but phone didnt boot afterwards. so i am very careful with this tool now.
I am just wondering why your sd loader (the OS image) update didnt work. because i had no probs with it so far. also from the hp orig files.
did you try the qpst update ???
if yes did it work if yes can you send a step by step ?
thx a lot
hi , try my patched ROMUpdate.dll mayby it could help , i dont try QPST because i have succesfully update my 614c with hpruu utility --> http://rapidshare.com/files/139300161/ROMUpdate.dll.html
did you also try the cooked wm6.1 os on it already ? does it work with the new fw0.88 ?
thanks !
yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok
Z!L0G80 said:
yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok
Click to expand...
Click to collapse
No success ... either with the romupdate.dll oder with the other tools.
A bit stuck now ... anz other suggestions ?
thanks !
forwarded
29 Jul 2008 release on HP Official Site HP iPAQ 612c WM 6.0en OS 1.01.04 FW 0.88
HOW TO USE:
1. Download the FILE to a directory on your hard drive.
2. Execute the downloaded file and follow the on-screen instructions to unpack the ROM update files to a directory. (NOTE: This directory should not contain any file or folder from any previous ROM upgrade)
3. Establish an ActiveSync connection between the iPAQ device and the host PC using a USB connection.
4. The ROM Update Utility (hpRUU.exe) starts automatically. Follow the on-screen instructions to complete the ROM upgrade.
NOTE: Once the update is complete, the FILE downloaded in Step 1 can be deleted, if desired
Download Link: http://www.mediafire.com/?sharekey=a65dc2a6e56aea29d2db6fb9a8902bda
Thats correct
But thats for english devices.
I have a german one where it doesnt work, and I am looking for a workaround.
Any suggestions ?
Get Hp Sp38905.exe http://h20000.www2.hp.com/bizsuppor...swLang=18&mode=2&taskId=135&swItem=hh-59339-1
Use winrar to unpack it.
You'll find an Eboot.nbf. This Eboot.nbf is language and SKU id independent.
Replace the file header of all .nbf files from hp 1.01.04 update by the header of this Eboot.nbf file.
The header is just the first 3424 bytes of .nbf files.
You do not need to change .mbn files.
Then you can run Hpruu.exe to update. The file names shown during updates are wrong, but results are right.
@kkwy
And what if, like in my case, sp38905 is reporting the same error.
product id: FB136AA#ABB
Just try to find one .nbf file that you can flash.
Then replace header file with the header file of that .nbf file.
The header seems to be useless (solely for checking) so you can replace then at will.
http://rapidshare.com/files/139300161/ROMUpdate.dll.html mayby now working ,try
EDIT> link updated
@ Z!L0G80
Yes, It works.
Thanx
Sucess!!
Now I have os 1.01.04, fw 0.88.
It takes a long time for radio firmware to flash, but, be patient.
Thanx again Z!L0G80
Thanx Z!L0G80's
It works for me to on the Dutch 614.
Strange thing is, that in de system config it stil says Dutch version of the mobile device (but it's UK now).
Very nice again.
ok great .... works ! thanks a lot !
would it also work with the 914 ? anybody tried ?
thx
My PDA already came with 1.01.04, fw 0.88 Rom, however I used the HP rom update utility to see if the rom would update without issues.
The rom update worked fine, however unfortunately something annoying is happening with this rom update. Now every time I try to do a clean boot, the first time the PDA turns on, after marking the screen, it would try to do some HP software update and right after the update I am forced to do a Reset, then I can use the PDA.
Previously I didn't have to do this, when I did a clean boot, the pda worked straight away after marking the screen, and I wouldn't need to reset it.
I think the reason for this maybe because this rom comes with extended rom, is there anyway of taking it back the way it was, or getting rid of the extra applications like the streaming player
This is the Rom I used
Type: BIOS
Version: 1.01.04 (22 Jul 2008)
Operating System(s): Microsoft Windows Mobile 6
File name: sp40097.exe (53 MB)
http://h20000.www2.hp.com/bizsuppor...3048-1&prodTypeId=215348&prodSeriesId=3544358
Am I the only one experiencing this issue, is there another rom that doesn't do this?
Thanks
anyone tried Sd loader modem with success?
what if the Activesycn not work?
I have tried copy the amss** files on SD, then sd loader modem. And wait so long time, 2 hours, and stay with the screen "write amsshd.mbn". I dont think it is working.
Anyone tried ?
Hi guys, so, I bricked my device, I was try update my ROM and my device was dead, I tried update with hw6915's rom but nothing worked, I need this ROM please, someone could help me?
Hi, this is dumped OS ROM 1.48NA from hw6945. ONLY FOR hw6945 !!!
Code:
[url]http://rapidshare.com/files/152256884/aWizard_hw6945.zip.html[/url]
This tools is free to use but at your own risk, I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure.
Hey spg, It is doen't work because my device is bricked, it is showing only the screen with HP logo with USB (when I put it in my PC) on top and vG.39 on footer. Could you help me? Ah I forgot one thing... my device is CID Lock.
http://rapidshare.com/files/46350136/Ipaq_HW69XX_ENG_ROM.rar.html
from folder delete CEBL.nbf, RadioFS.nbf, RadioOS.nbf, and view picture from attachmend. Not work? Sorry for bad english.
Thanks bro, I'll to try when I arrive in my home!
hey brooo... Didn't nothing with name Sable_RUU in the folder that you send to me...
spgi said:
Hi, this is dumped OS ROM 1.48NA from hw6945
Code:
[url]http://rapidshare.com/files/152256884/aWizard_hw6945.zip.html[/url]
This tools is free to use but at your own risk, I take no responsiblity for any conflict, fault, or damage caused by this flashing procedure.
Click to expand...
Click to collapse
Hi Spgi,
I followed the instruction and got a error while write the hp6945-os.nba, now my phone halt on HP logo with 1.00.00 and 1.48NA at the lower right corner screen. How to do know? can you help?
Except that another can not help:
http://forum.xda-developers.com/showpost.php?p=2787865&postcount=5
Sorry
spgi said:
Except that another can not help:
http://forum.xda-developers.com/showpost.php?p=2787865&postcount=5
Sorry
Click to expand...
Click to collapse
Hi Spgi, successful recover my 6965 to 1.21UK ver now, but I am interesting in OS ROM 1.48NA from hw6945, I tried twice of your dump by aWizard, failed twice, is there any way to dump or conver the HP6945-os.nba to NBF format? Could you pls upload a NBF format ROM?
Oh, by the way, I used to dump my phone by grab_it, do you know how to write the dumped bin file back to phone? thank a lot, bro!
Hi Spgi, would you pls reply me? tks!
3circles said:
Hi Spgi, would you pls reply me? tks!
Click to expand...
Click to collapse
Hi, transformation is impossible.
so can anyone help me with a working ROM on 6945?
Man,I read ur thread what u memtioned use MTTY to change the device ID,u r great!
But actually I tried to use MTTY to make my HP6915 device to be upgraded again,apparently I failed. No! exactly was my device failed when the flash tool working. My device just lost GSM at the beginning,then I tried to fix it by flashing,but seems the USB port of device be block,the flash tool always notice :" Error:201" when upgrading
Do u have any idea to help me out of this problem?
spgi said:
http://rapidshare.com/files/46350136/Ipaq_HW69XX_ENG_ROM.rar.html
from folder delete CEBL.nbf, RadioFS.nbf, RadioOS.nbf, and view picture from attachmend. Not work? Sorry for bad english.
Click to expand...
Click to collapse
bramblyrose said:
Man,I read ur thread what u memtioned use MTTY to change the device ID,u r great!
But actually I tried to use MTTY to make my HP6915 device to be upgraded again,apparently I failed. No! exactly was my device failed when the flash tool working. My device just lost GSM at the beginning,then I tried to fix it by flashing,but seems the USB port of device be block,the flash tool always notice :" Error:201" when upgrading
Do u have any idea to help me out of this problem?
Click to expand...
Click to collapse
Hi,
1. Get the latest ROM for your device from HP !!
2. Create a flash.dio file with these instructions
3. Put that flash.dio on a SD card (!!!! NOT SDHC !!!!)
4. Put the SD card in your device.
5. Press action-action + reset to enter Bootloader mode according to instructions here
6. Wait end of flash
7. Clean Boot
Dirk
The latest ROM I got just the 1.21 EN version for HP6915 G4,I did extract the file but I never seen "FLASH.NBF" whatever,that make me confused,u know.
dirlan2001 said:
Hi,
1. Get the latest ROM for your device from HP !!
2. Create a flash.dio file with these instructions
3. Put that flash.dio on a SD card (!!!! NOT SDHC !!!!)
4. Put the SD card in your device.
5. Press action-action + reset to enter Bootloader mode according to instructions here
6. Wait end of flash
7. Clean Boot
Dirk
Click to expand...
Click to collapse
Been a long time since these posts...
There's a workaround for your HP iPAQ hw6945 SERIAL/USB v.G 39 screen problem:
Disable ActiveSync, and install the GSM Radio Stack Firmware Upgrade sp35602 again, that was never mentioned in the instructions, but it sure worked, and my 6945 is now back among the living
spgi said:
http://rapidshare.com/files/46350136/Ipaq_HW69XX_ENG_ROM.rar.html
from folder delete CEBL.nbf, RadioFS.nbf, RadioOS.nbf, and view picture from attachmend. Not work? Sorry for bad english.
Click to expand...
Click to collapse
now it is no useful.
Please Help!
I've been looking all over the internet for the english ROM for my ipaq hw6945 with no success. The WM in my ipaq is in spanish and all the updates for it are in english so none of the updates will install (they dont pass the validation). Is there a workarround for this? Or do you guys have a ROM in english for my device? Much appreciated!
Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal
Good job, thanks!
Will try it out later!
is it still compatible even though my device SKU IDs is not compatible with the update?
Last time i tried i almost bricked my device.
In theory, yes
Actually, like I wrote above.
My ipaq 914c is Italian version.
It means that the SKU IDs of the phone is not not compatible with the update. ( I mean the official update!)
But we all know that there is no difference in the hardware between the ipaq 91x.
So any language ROM versions can be used on the another ipaq 91x phone.
=> WWE ROM can be used on any Ipaq 91x phone.
My Ipaq now is in English. But the SKU IDs still show that it's in Italian.
By the way, I forget to thank: Z!L0G80.
i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx
AbsolutBenz said:
i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx
Click to expand...
Click to collapse
Hi,
As it was given like that, I think you should check the usb cable. Sometimes the cable is not working well. I use the original cable, because the last time I use another there was an error when it was flashing. (I'm not sure if the active syn is necessary. In my case, I have the active syn on my laptop. XP enviroment.)
If you want to try the SDBootloader you can find in this forums some instructions about cutting some bytes to obtain the flashdio.nb0
But I really don't recommend that way. Because the last time when I find the way to change the language by flashing the english Rom following those instruction. My phone was bricked. So I tried to find another way.
And this is it.
I think this method is the safest way for newbie. As I wrote above. The first time I bricked my phone. But I did the same procedure again. And it worked.
Just check the procedure again.
Good luck,
For the SDloader update (Which works very very well on my German 914c):
download the file below (I already cut the first 3432 bytes from it), put it on a newly formatted SD-card (not SDHC!) and hold down volumeup+OK button (the one on the right side) while pushing the reset button, hold the mentioned sidebuttons until you see SDloader. Then wait for a few minutes, and the update will finish!
If the updater does not find the file, you have to re-format the SD-card to either FAT or FAT32!
Rename the file to FLASH.DIO when you copy it onto the SD-card!
http://rapidshare.com/files/236053650/FLASH.DIO.html
vragon said:
Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal
Click to expand...
Click to collapse
Hi Everybody,
@vdragon
1- what a great job, guy!
2- in reality, i have already flashed your ROM successfully for my ipaq 914c, which is a native italian version. Since the incompatibilites of different versions were resolved perfectly.
3-Grazie tanto di nuovo
I'm pretty new with this and I've been trying to update my 910 with original ROM but for some reason it gets stuck and the only way to bring it back is with a SDLoader I downloaded from here but that one is very simple and I'd like one with all the programs.
Is there a way to load yours on it through the SD card?
you can follow the instruction to cut the 3432 bytes and flash your phone with SD card.
I see that many people prefer to use the sdloader method than this one.
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.
vragon said:
...
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.
Click to expand...
Click to collapse
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?
congtiger said:
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?
Click to expand...
Click to collapse
sure
congtiger said:
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
Yes it is true!
Using vragon's patched Updater the following is updated:
OS (=ROM)
Bootloader
Pre-Bootloader
Radio&Modem
This update takes about 20minutes, so be patient, do not remove any cables during update!
The flashing of FLASH.DIO with an SD-card "only" updates the OS (=ROM) and is done within less than 10minutes.
Thanks vrago for patching the Romupdate.dll!
You can also see it in the bootsplash screen. Before the update (even after SDloader updates) it always showed FW 1.04.
Now it is 1.09 - and yeah, it works GREAT and quick!
I can recommend it!! (I do not take responsibility though)
Should be a sticky!!
I've been trying this file, and I get an error at 51% of update. Any ideas?
I think it's about your cable. Be sure that you use the original cable with the anti-noise hub.
If you didn't success the first time. Try it again.
Do as you did the first time.
And just be patient. Don't move anything.
The first time I used this method, at the middle of flashing, I kicked my cable and it just stopped. And I did it again carefully.
So that's it
Actually, I think I figured it out. It seems that Vista treats USB partnerships differently than XP, so after a certain amount of time, it "refreshes" the relationship with the USB device. If you are trying to flash your phone, that stops the flash/update.
I just used my XP system, and it worked fine. After a few registry tweaks for ring volume and battery life, it's working fine.
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
I'm positive the SD Loader method isn't as thorough as this method. This method takes 20 minutes or so, and you can see that it's updating the pre-loader, modem/radio, etc. The SD method only updates software.
Problem using HP 614c from original ITA rom
I am a stupd guy
I am a stupd guy
I am a stupd guy
Hy vragon, i have used your method to upgrade my device 614c (and not 914) from an original Italian ROM. All process is ended correctly, all upgrade are finished without errors.
The update utility has made the update of that:
Software - From Version - To Version
Bootloader - 1.00.07 - 1.01.01
Windows Mobile 6.1 Professional - 1.00.07 - 1.01.01
Pre-Bootloader - 1.00.07 - 1.01.01
iPAQ WAN Radio Firmware - 0.81.00 - 1.09.00
But after the upgrade, at the end the display was black(not really black i can see the leds of the entire display are ON but das not appear nothing), and after some minutes abouth 20, i removed the battery and restart the device but nothing has changed. The led over the screen and the sound working.
I have try also to do a hard reset with a flash.dio on an SD card inserted to replace the Rom, but dose not work!
The device after that will work properly, and das not appear to have any problem.
CAN SOMWONE HELP ME !!!
@ilconte81:
just go to hp site.
find a ROM update for 614c.
download it.
using winrar to extract everything in the exe file.
copy the ROMupdate.dll from my file to replace the file in the folder which is extracted from exe file.
run the rom update again.
Tanks for reply vragon,
i have tryed to do what you wrote, but the device will not be right recognized from the OS (will appear USB device not recognized) and the update utlity after a long time in "Plese wait while the device state is verified" give the comunication error Code 402, Cannot comunicate with device.
I use the original cable and try these on different OS like Win XP and Win 7.
hi everybody i am new here and i need some help
How To Install a Rom in Omnia 2 (i8000)
step by step
and thanks
Hi chabahed
I was in the same boat few days ago. After doing some research in modaco, xda forum - I had succeeded in install energy rom (I install PDA part only) - Great ROM, i must say.
You can read more at modaco forum (sorry, can not post URL since I am new member)
I only worked on windows XP - It can be done on windows 7 but I had not tried it yet
- Require software to install you need:
ActiveSync installed (from microsoft webside)
Samsung_CDMA_modem_4_1_.34.zip
OCTANS_Mini.v2.11.exe
(see the modaco link for a link to download those software)
1. Insteall ActiveSync (if you had not done so)
2. Extract Samsung_CDMA_modem_4_1_.34.zip to a directory, and run the "setup.exe" in that directory to install the drive
3. Turn off your phone (push and hold on the right button of the cube button for a few seconds) - DO NOT USE THE RIGHT SIDE BUTTON (turn off screen only) - DO NOT CONNECT THE PHONE TO YOUR PC at this time
4. Run OCTANS_Mini
5. Click ".NB0" button to upload the PDA rom that you want to flash - Now the Detect button is enabled
6. Click Detect button
7. Now connect the phone to your PC using the supplied USB cable - the phone should be off as step 3 above.
8. Wait until OCTACT detect the phone - now the Start button is enabled
9. Click on the Start button to start flashing the ROM to you Omnia2 phone
10. Take a deep breath, drink a cup of coffee - Wait until the phone seft power on and start initializing
11. Enjoy your new shiny beautifull phone - (As I am with mine )
Hi, Vphung. I'm on official Rom 6.5 proffessional. But it doesn't look cool like those customized rom. So i want one. Any suggestion on any ROMs cool and perfect for Samsung Omnia 2 i8000? and of course, if possible please provide the link to download that roms. Thanks.
Kanntola said:
Hi, Vphung. I'm on official Rom 6.5 proffessional. But it doesn't look cool like those customized rom. So i want one. Any suggestion on any ROMs cool and perfect for Samsung Omnia 2 i8000? and of course, if possible please provide the link to download that roms. Thanks.
Click to expand...
Click to collapse
I'm using JI1 Cooked ROM ....{ Cooked By MS Team }
it's cool
i'm using it for a while now..and i didn't find any bug in it yet..!!!
Looking alot here on XDA reading things about roms and such. But I wonder. If I would like to go back to the original rom (factory default), is that still possible? I only have this phone so I don't want to get stuck and having no phone at all.
Installing via Windows 7 machine
vphung said:
Hi chabahed
I was in the same boat few days ago. After doing some research in modaco, xda forum - I had succeeded in install energy rom (I install PDA part only) - Great ROM, i must say.
You can read more at modaco forum (sorry, can not post URL since I am new member)
I only worked on windows XP - It can be done on windows 7 but I had not tried it yet
- Require software to install you need:
ActiveSync installed (from microsoft webside)
Samsung_CDMA_modem_4_1_.34.zip
OCTANS_Mini.v2.11.exe
(see the modaco link for a link to download those software)
1. Insteall ActiveSync (if you had not done so)
2. Extract Samsung_CDMA_modem_4_1_.34.zip to a directory, and run the "setup.exe" in that directory to install the drive
3. Turn off your phone (push and hold on the right button of the cube button for a few seconds) - DO NOT USE THE RIGHT SIDE BUTTON (turn off screen only) - DO NOT CONNECT THE PHONE TO YOUR PC at this time
4. Run OCTANS_Mini
5. Click ".NB0" button to upload the PDA rom that you want to flash - Now the Detect button is enabled
6. Click Detect button
7. Now connect the phone to your PC using the supplied USB cable - the phone should be off as step 3 above.
8. Wait until OCTACT detect the phone - now the Start button is enabled
9. Click on the Start button to start flashing the ROM to you Omnia2 phone
10. Take a deep breath, drink a cup of coffee - Wait until the phone seft power on and start initializing
11. Enjoy your new shiny beautifull phone - (As I am with mine )
Click to expand...
Click to collapse
This is the way of installing within Windows XP but it will not work inside Windows 7.
Any ideea when PC only runs Win7?
Thanks & Regards,
hmm I'm trying this exact procedure in XP, w7-64, w7-32, in neither Pc is the program able to detect the phone.
I must add though that i had tried to do an update using KIEs. It hang in mid-upgrade.. and i had hopes that Octans could repair this bricked phone,
anyone else having this predicament?
Ihave flashed my omnia with vista 32 bit and windows 7 64 bit ...flashing with vista 32bit is easy but you need to update the vista driver...
For windows 7 64 bit you need to stop the stupid driver signature enforcement at the start of windows by pressing F8 during the bootloader or installing DSEO( Driver Signature Enforcement Overrider) which is a free application( and you can google it) to do that before updating the driver ...there is a specific driver for 32 bit and 64 bit in windows 7....I have attached vista driver and w7 23 and 64 drivers....
maybe somebody can help me.
i made some flash to my fone, no problem under w7. onde day trying a new flash, the mobile simply don't talk with my pc.
format c:\
install w7, install drivers, nothing happen.
format
instal xp, same procedure. nothing happen.
hard reset between flash ...
now i have the phone full of samsung, windows, and my provider trash.
something like 37 mb memory
and ..i can't charge my phone when is on, only when i turn it off he charge the baterry via usb or wall charger.
i have two cable.
if somebody have some suggestion idea, resolution.
tks
wat is d use of changing d ROM's?? im new here so pl help me
---------- Post added at 09:21 PM ---------- Previous post was at 09:15 PM ----------
can u also give me a direct link to install windows phone 7 onto omnia2?? i need help i searched a lot but i didnt find it can u pl help me??
[email protected] said:
wat is d use of changing d ROM's?? im new here so pl help me
---------- Post added at 09:21 PM ---------- Previous post was at 09:15 PM ----------
can u also give me a direct link to install windows phone 7 onto omnia2?? i need help i searched a lot but i didnt find it can u pl help me??
Click to expand...
Click to collapse
1.There is No Windows Phone7 for Omnia2
2.Read carefully post by member vphung
thx..
hi i want to flash my htc touch dimond 2 but when in tri colour mode i conect it to pc . pc giving error usb device not recognised what shoud i do for it becous whithout contecd phone to pc i not able to flash it.
262068 said:
hi i want to flash my htc touch dimond 2 but when in tri colour mode i conect it to pc . pc giving error usb device not recognised what shoud i do for it becous whithout contecd phone to pc i not able to flash it.
Click to expand...
Click to collapse
to resolve it, try installing the ms ActiveSync (for Win XP) or WMDC (Vista and Win 7) on your computer !
ActiveSync ~ http://www.microsoft.com/en-us/download/details.aspx?id=15
WMDC ~ http://www.microsoft.com/en-us/download/details.aspx?displaylang=en&id=14
i am using windows 7 and i install your given link driver but problem still same any other solution thanks for help dear
to flash the rom does not need to bring the device into botloader, simply connect your phone to your computer and wait until activesync /Windows Mobile Device Center admit and then run instead of .exe file (CustomRUU) at the rom
first thanks for help bro and in this phone when we switch it on its show htc window then restart so tell me how i flash it its not conected to pc in this condition . i do soft and hard reset on this phone already .give me full prosses link .
262068 said:
first thanks for help bro and in this phone when we switch it on its show htc window then restart so tell me how i flash it its not conected to pc in this condition . i do soft and hard reset on this phone already .give me full prosses link .
Click to expand...
Click to collapse
I think, you still can Flash ROM at your device using the Storage Card ! follow the guide at here ~ http://forum.xda-developers.com/showpost.php?p=7033683&postcount=3
thanks bro i understand all way to flash i download file and put it in blank mmc root dir with change name after that i press down volume key + power key phone start in tri color screen but after that its showing Loading... on screen and nothing more i wait one hour in this condition but nothing happen only loading showing .so what is problem or mistak i do in flashing tell me
262068 said:
thanks bro i understand all way to flash i download file and put it in blank mmc root dir with change name after that i press down volume key + power key phone start in tri color screen but after that its showing Loading... on screen and nothing more i wait one hour in this condition but nothing happen only loading showing .so what is problem or mistak i do in flashing tell me
Click to expand...
Click to collapse
previously make sure your MicroSD has formatted to Fat32! to format a memory card you can use the SD Formatter
open your file rom with winrar, Drag and drop ruu_signed.nbh file to a folder on computer then rename ruu_signed nbh. file to TOPAIMG.nbh and copy to memory card
plese bro give me a working rom link for this htc touch dimond 2 T5353 phone and thanks for all this help. i tried in this fourm but not able to find which is working perfect or not .
and i use 2gb card is thair any probem with card capacity
262068 said:
plese bro give me a working rom link for this htc touch dimond 2 T5353 phone and thanks for all this help. i tried in this fourm but not able to find which is working perfect or not .
and i use 2gb card is thair any probem with card capacity
Click to expand...
Click to collapse
no problem with capacity Card
Maybe you could try with the official rom http://shipped-roms.com/index.php?category=windows%20mobile&model=Topaz
bro in your link all file in exe extention how can i use that and when run in exe mode give some error in setup error message written in other language so i not understand any suggestion thanks bro
262068 said:
bro in your link all file in exe extention how can i use that and when run in exe mode give some error in setup error message written in other language so i not understand any suggestion thanks bro
Click to expand...
Click to collapse
You can view the contents of the file and extract it using WINRAR
I Download 5 rom files when i format card using fat in this condition its showning after tri screen looding then no image found and return to tri screen . and when i format card using fat32 its showing loading then chacking then not allow then return to tri screen whats happen bro tell me thanks.
hi bro whats happen . give me any idea
bro my problem still not solve i not able to flash my htc diamon2
262068 said:
bro my problem still not solve i not able to flash my htc diamon2
Click to expand...
Click to collapse
Can attach screenshot your device at the time of the bootloader mode ??
hear is video bro i format mmc with fat32 and fat (same result in both) then put rom file in root dir with change name as you given in this video after tri colour say loding then no image fond then return to tri colout screen back
say somthig bro
have you tried using another memory card ??
Is not clear what SPL you have.
Loading then not allow means that ROM is for other country.
Also means that you don't have Hard SPL.
You can recover only with ROM for what country ID have your device.
HTML:
You can recover only with ROM for what country ID have your device
how can i find country id in my set. in back panel of set i found made in tiwan is thair any solution now
tell me something my problem not solve
If your device the last time before brick still using the embedded operating system (ROM) default from the manufacturer, then you get to know country ID via specifications Shipped ROMs / official ROM at W I K I