Hi,
Hp just released an update for the 614, only for englisch.
I have a german 614
I dont care about the OS part since I use a cooked 6.1.
But the update also contains a modem / radio update to version 0.88.
Currently out there i think there are 0.77 and 0.81 depending on language.
I believe the radio fw is language independent when it comes to functionality. But the hpruu says wrong language.
With the current universal hpruu tools you can only update the OS which is of no use.
I know you can update the radio by booting with the key combination:
lower left key on the side (record button) and the camera button.
Then turn on ... it shows : SD loader for modem
(similar on how you update the OS)
I also know that the radio update files are in the update.
They are called
amss.mbn
amsshd.mbn
maybe also partition.nbf
But I am not sure about this.
It might work with just copying the file to a non HC SD card and using the key combination.
There might be some file renaming involved.
I someone out there to try that and let us know how it worked ?!
Thanks
sax
hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull
Saxon,
File partition.nbf is for IpaqFileStore update.
Maybe you should try with the following way:
- extract the whole package from HP side
- remove from the obtained directory the OS file (the larger one)
- put your device into SDloader state (voice recorder + mute + power on)
- connect your device into PC via USB
- launch RUU utility
In my opinion there is a big chance it will work.
Such way (using the SDloader) was working for one polish case where the upgrade of firmware failed due to PC crash. The only chance to flash again was to use SDloader + HP tool.
Good luck.
Z!L0G80 said:
hi, imho theoreticaly you can update
1) .mbn files with qualcomm loader(SD Loader for modem) iam tryied it but no luck , .mbn files from hp 1.01.04 update have bad format not usefull for flashing from sd card :/
2) .nbf files from eboot loader(SD Loader), no luck bad format too :/
other way you can use QPST tools from Qualcomm or QC BS Firmware Analyzer(avaliable on xda forum)
small how-to connect ipaq614c for using with this tools
1) put ipaq to modem mode (push ML and power on)
2) connect ipaq to pc
3) install MotoQdrivers.zip (dont forget to adjust speed for COM ports)
i have included Qualcomm MSM6280 loader for QPST - NPRG6280.ZIP (ipaq 614 have this chip for radio)
sorry for this chaotic text i hope that is usefull
Click to expand...
Click to collapse
I used the qpst already and it worked that way that i could upgrade but phone didnt boot afterwards. so i am very careful with this tool now.
I am just wondering why your sd loader (the OS image) update didnt work. because i had no probs with it so far. also from the hp orig files.
did you try the qpst update ???
if yes did it work if yes can you send a step by step ?
thx a lot
hi , try my patched ROMUpdate.dll mayby it could help , i dont try QPST because i have succesfully update my 614c with hpruu utility --> http://rapidshare.com/files/139300161/ROMUpdate.dll.html
did you also try the cooked wm6.1 os on it already ? does it work with the new fw0.88 ?
thanks !
yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok
Z!L0G80 said:
yes, when i update fw i reflashed my own 6.1 based on yevg001 v1.4 and works ok
Click to expand...
Click to collapse
No success ... either with the romupdate.dll oder with the other tools.
A bit stuck now ... anz other suggestions ?
thanks !
forwarded
29 Jul 2008 release on HP Official Site HP iPAQ 612c WM 6.0en OS 1.01.04 FW 0.88
HOW TO USE:
1. Download the FILE to a directory on your hard drive.
2. Execute the downloaded file and follow the on-screen instructions to unpack the ROM update files to a directory. (NOTE: This directory should not contain any file or folder from any previous ROM upgrade)
3. Establish an ActiveSync connection between the iPAQ device and the host PC using a USB connection.
4. The ROM Update Utility (hpRUU.exe) starts automatically. Follow the on-screen instructions to complete the ROM upgrade.
NOTE: Once the update is complete, the FILE downloaded in Step 1 can be deleted, if desired
Download Link: http://www.mediafire.com/?sharekey=a65dc2a6e56aea29d2db6fb9a8902bda
Thats correct
But thats for english devices.
I have a german one where it doesnt work, and I am looking for a workaround.
Any suggestions ?
Get Hp Sp38905.exe http://h20000.www2.hp.com/bizsuppor...swLang=18&mode=2&taskId=135&swItem=hh-59339-1
Use winrar to unpack it.
You'll find an Eboot.nbf. This Eboot.nbf is language and SKU id independent.
Replace the file header of all .nbf files from hp 1.01.04 update by the header of this Eboot.nbf file.
The header is just the first 3424 bytes of .nbf files.
You do not need to change .mbn files.
Then you can run Hpruu.exe to update. The file names shown during updates are wrong, but results are right.
@kkwy
And what if, like in my case, sp38905 is reporting the same error.
product id: FB136AA#ABB
Just try to find one .nbf file that you can flash.
Then replace header file with the header file of that .nbf file.
The header seems to be useless (solely for checking) so you can replace then at will.
http://rapidshare.com/files/139300161/ROMUpdate.dll.html mayby now working ,try
EDIT> link updated
@ Z!L0G80
Yes, It works.
Thanx
Sucess!!
Now I have os 1.01.04, fw 0.88.
It takes a long time for radio firmware to flash, but, be patient.
Thanx again Z!L0G80
Thanx Z!L0G80's
It works for me to on the Dutch 614.
Strange thing is, that in de system config it stil says Dutch version of the mobile device (but it's UK now).
Very nice again.
ok great .... works ! thanks a lot !
would it also work with the 914 ? anybody tried ?
thx
My PDA already came with 1.01.04, fw 0.88 Rom, however I used the HP rom update utility to see if the rom would update without issues.
The rom update worked fine, however unfortunately something annoying is happening with this rom update. Now every time I try to do a clean boot, the first time the PDA turns on, after marking the screen, it would try to do some HP software update and right after the update I am forced to do a Reset, then I can use the PDA.
Previously I didn't have to do this, when I did a clean boot, the pda worked straight away after marking the screen, and I wouldn't need to reset it.
I think the reason for this maybe because this rom comes with extended rom, is there anyway of taking it back the way it was, or getting rid of the extra applications like the streaming player
This is the Rom I used
Type: BIOS
Version: 1.01.04 (22 Jul 2008)
Operating System(s): Microsoft Windows Mobile 6
File name: sp40097.exe (53 MB)
http://h20000.www2.hp.com/bizsuppor...3048-1&prodTypeId=215348&prodSeriesId=3544358
Am I the only one experiencing this issue, is there another rom that doesn't do this?
Thanks
anyone tried Sd loader modem with success?
what if the Activesycn not work?
I have tried copy the amss** files on SD, then sd loader modem. And wait so long time, 2 hours, and stay with the screen "write amsshd.mbn". I dont think it is working.
Anyone tried ?
Related
Hello
I just did the following :
download the files from www.carrierdevices.com.au for Qtek 101 update
"Qtek 1010 Upgrade
(22102003-190723)-RSUv1.15_(GPRS_T32500_ENG).exe
File Contents
• CE Upgrade File : RUU_CEv3.18.04wwe_Qtek_SHIP.exe
• Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe
"
When the process began there was an error asking to press OK for restart.
After restarting device in the boot sequence ( when logo is diplayed) there are no informations about the ROM. Just Radion version is diplayed and that is the new version one (3.25)
Also on the display there is no start icon and I cannot use the display because it seems to be decalibrated completly.
Very Important : When I try to connect to Activesync after a while it telling me that the device is not a smartphone or a pocket PC and cannot be connected. So I cant use any program to try to upgrade again.
What to do ?
Please try to give examples and link to download files in order to fix my device.
Thanks in advance
Silviu C.
Hi ...
If you still can get to the boot loader screen (power button + soft reset) and it displays "GSM OK", that means there is a good chance that the flash ROM is not damaged.
You can either put the ROM and RSU files on SD card through a card reader (.nbf files) or to get a valid SD backup for CE + Radio from any working XDA and use the boot loader screen to flash your device again.
Good luck ...
thanks, where I can get some files?
Thank you for your replay,
It seems to be ok cause i can upload a new CE in SD format to the device. ROM was build in the kithcenROM from yorch.net.
It still not working cause perhaps I need the file containing Radio and CE as well in SD format.
Do you know where I can get it ?
I dont think I can get another device to read the files on the SD.
Many thanks,
Silviu C.
I 'm not sure which stage you are stuck with now ... if you can put CE image on SD card and flash it using the boot loader, that means you can boot your XDA and flash the RSU through a normal EXE file from yorch.net .... if this is not the case then you most propably have the wrong file format on the SD card.
Give more details plz
present situation
I am at the edge of disperation.
Steps of what I did :
1. Back up Boot and CE to SD and save them to HDD.
2. Build a CE from Yorch.net in nb1 format and write it to SD with an adaptor.
3. Flash the device with that specific file ( was just CE , not including bootloader)
Now, my pocket is like that:
It cannot been powered from the power button
It start when plug in the charger
I cannot go in bootstrap mode ( when procedure for activating is made I just got a small red flash from the LED)
I have to mention that I choose from the yorch options :" lock butons except power when the device is turned off "
So, now I cannot use the SD for try another flash image.
I cannot use activesync because it cannot recognize the device. Somthing is wrong in the header of the authorising string or something like that.
When I plug the USB cable, activesync is starting but after 10 secs a pop up telling me that the device cannot be recognize, it is not a smartphone or pocket pc.
I am stack.
Thank you
Silviu C.
another question
I have another question:
Is there anywhere - in situation that the problem with boostrap will be solved somehow - full flash containing both radio and CE ?
Thank you,
Silviu C.
some little success
I have suceded by entering in bootrap mode !!
It telling me that I have GSM ERROR
What to do?
IS there any way I can get a full flash for Qtek with radio and OS as well?
Thanks,
Silviu C.
In the boot loader screen, try to press the calendar button ... it should give you the GSM menu. Select "Reset" or "Turn off" and do a soft reset
Plz do NOT try band switching or "Calib/debug"!
It sounds like a failed radio stack upgrade, you can try copying the RSUpgrade.sa.CAB file to your SD card then run it from there.
You can get the RSUpgrade.sa.CAB file by using WinZip to extract it from the RSUv1.15_(GPRS_T32500_ENG)[1].exe file.
HTH
hi,
Sum1 here who a T-Mobile subscriber? I have a T-Mobile PocketPC that I need to unlock tho I'm not a T-Mobile subcriber. I need a T-Mobile mobile number to get the upgrade at http://www.t-mobile.com/products/handhelds/pocketpc/download_popup.asp
Or if someone already downloded the upgrade where can I download it without keying-in the mobile number? Thanks.
BTW, I have a question, if I download the upgrade, can I now use the XDAunlock.exe file here (is my ROM automatically updated)? My ROM version now is 3.14.40 ENG. I'm having trouble with the ROM updater here since im not linux literate.
Email me at [email protected]. Thanks a lot
I already downloaded the TMobile upgrade. Can somebody tell me if this upgrade will indeed upgrade my ROM to the correct ROM version with wirelss modem feature to I can use the XDAunlock.exe to unlock my xda? Thanks
The answer is NO, the latest TMO upgrade is 4.01.00 and it has no wmodem.exe application. If you need to unlock your device, go to www.xda-developers.com/XDAunlock/ and use the tool there.
If it doesn't work, try the kitchen at www.yorch.net and cook a new 3.17 based ROM and flash your XDA and unlock it, then you can upgrade to TMO 4.01.00 later.
BTW, the TMO upgrade affects the RSU part. So, unless you are a TMO user you better use the .nbf file only with either SD card or use the XDAtools to flash your device.
Good luck.
Hi Biso,
How can I "cook" a rom? http://kitchen.romanweb.com/kitchen/index.php when I go to that website, the only thing needed to be selected are the 3.17.03 ENG O2-Euro (6656 kB available) and XDA-developers AutoConfig data (113 kB) under it. and the unlocking option right? This wil be the first to use my pocket pc device, which option should I select under How would you like your ROM?
installer EXE
zipped NK.nb1 (SD-card flashing)
zipped NK.nbf (advanced users)
and should I do anything on the NBF header string?
Thanks man.
If I use the intaller EXE file, how will I "flash" it on my device? What are the differences between using the exe,nk.nb1 and nk.nbf? Thanks again.
I notice that above the page there is an indication, by default when I go to the page (without checking or unchecking anything) the top of the page states:
space in ROM: 6656 kB
used: 7729 kB
free: -1072 kB
*overload*
Should I limit my ROM on 6656 kB (meaning that I have to uncheck other options)? My deveice is an XDA 1. Thank you.
Hi ...
Yes, you have to uncheck some optional s/w till the guage line is "Green".
If you are not familiar with the SD method, just select the EXE type. It will generate a 15 MB exe file which you should download it to your PC. Connect your XDA to your PC throught the cradle and ActiveSync and run the exe file while the cradle is connected to the power supply and follow the instructions on the screen.
Good luck.
Thanks man for the quick reply.
Sorry I'm getting confused. Should I transfer the exe file to the device and run the exe file on the device?
Thanks again
The exe file runs from your desktop, your xda will need to be synced with your pc before running the exe.
Thanks so this is what I have to do:
First sync my device (cradle connected to the power supply) and after synching, run the exe file on my desktop computer (no need to transfer on my device or anything?). That's it?
Is this fail-proof? Will it not damage my device if ever there was an interruption or sumthing? How can I make sure that I can go fail-proof? Kinda worried coz I just got hold of my xda 1 (T-Mobile edition), I'm a palm user before. Thanks
BTW, my PocketPC Version is 3.0.12039 (Build 11178). ROM version 3.14.40 ENG. I don't know if my PocketPC is 2002 or 2003. I'll be using the yorch.net ROM (http://kitchen.romanweb.com/kitchen/index.php). All compatible?
ROM 3.14 is a PPC2002 one and all ROMs on Yorch.net is WM2003 except the 3.17 one.
Just to ensure it's a safe process, remove the SIM and SD card from the device and stop any running applications on your PC.
Good luck ...
Thans Biso. How bout a step by step guide? Pls pls pls? Id really appreciate it man.
Like
1. Sync the device (Power connected to the cradle)
2. Run the Rom Exe file
3. etc.
Just to be sure. BTW, is the exe file really just 150KB? Is that all I need to unlock my device?
Hi ...
There is nothing really needed more than what you just wrote:
1. Connect the XDA to the cradle and sync while the power is connected.
2. Run the EXE file and follow the instructions on the screen.
BTW, the EXE file should be at least 15 MB, seems your ROM was not "cooked" well .... try again
Ohh ok. I downloaded twice and all I got was 150kb. how will I know that the ROM i got is "cooked" well so I can be free of troubles. Can you just give me a link to the right/"well cooked" ROM? Thanks man.
One more thing, should I run the ROM EXE file while my device is synching or after the synch?
it's still 150 kb. Here's what it says when I view the log
./mkrom.sh: ../../kitchen.local/mkrom-inc.sh: No such file or directoryno files for configid 26220739Cannot fit files in given sectionsError splitting files
seems there is something wrong with the kitchen work space ... it happens sometimes ... no big issue.
You may try this kitchen as well http://lumpistefan.dyndns.org/
P.S: run the EXE file after the device is synced
which one should I pick? Pocket PC 2002 ROM or Windows Mobile 2003 ROM. And what's the difference. Sorry for my ignorance. Thanks for the replies.
Biso,
Can I use an MMC card for flashing? I MIGHT be able to borrow an MMC card. Also, I dont have a card reader but I have a digital camera which I can use to transfer the ROM image from my desktop computer to the card. Would you think it would work? Thanks again man.
will the exe file below work for me?
http://cuba.calyx.nl/~jsummers/XDA/XDA-developers-SER-v12.exe
and
http://www.xs4all.nl/~jsummers/XDA/XDA-developers-SER-v12.exe
This is my Device's Information
ROM version: 3.14.40ENG
ROM date: 11/26/02
Radio version: 6.18
Protocol version: 324e4
Pocket PC Version 3.0.12039 (Build 11178) (Don't know if this is 2002 or 2003 pocketpc)
Pls reply. thanks
Hi ...
1. As the figure tells, WM2003 is the latest than PPC2002.
2. I can recommend to use TMO 4.01.00 as I have it on my device for almost 3 months now with no problems so far (few things have to be tweaked tho), but I heard good news about AT&T 30.09 ROM as well.
3. I can't confirm that MMC can replace SD card. I saw some threads on this but no final results.
4. The answer is NO, the only way to move the NBF file to the SD card is either a card writer or by using XDAtools with the XDA cradle. I don't think the card will be recognized by the bootloader otherwise.
5. SER-V12 is a PPC2002 ROM and useful only if you need to unlock your device (which I believe it's already unlocked).
No I just want to unlock the device, that's it I don;t really want a ROM upgrade, just so happens that I need to have a ROM upgrade to unlock the device
SO I can use the SER-V12? Thanks a lot.
B]I have IPAQ 5550 1.00.13 ENG [/B]
I have installed TomTom 5.21 + Benelux Map on it. So i have about 5-10 mbyte free memory left.
when i try to install Rom version 1.00.18 19 Nov 03
and restart the Ipaq its freeze at HP logo at blue screen.
-----------------------------------------------------------------------
I have download ROM Update 1.10 (7Apr 04) from
http://h18007.www1.hp.com/support/files/HandheldiPAQ/us/locate/105_5643.html
I set my Ipaq to flash mode itask+calendar+contact+Reset
[b](My computer is formatted only Windows XP PRO+Activesync+Flash file is installed No firewall is installed, No screen server, no program running at same time)[/b]
I disable Activesync before start flash CTRL+ALT+DEL kill wcescomm.exe
Ok flash starting normal when it is at 28% is does not continue it´s only froze / hang on /stop.
I use Sync/Charge usb cable NEW BUYED
I have try on 4 different Computers.
I have try with USB Cradle + 220 Power connected to cradle.
Same problem flash starting and froze at 28%
Could it be Because before flashing the Rom i must make a hard reset to clear all software and make free memory.
I have also try to edit FUU.BIN + KERNEL_SKUB128_1_10_10.nbf
with Ultraedit (www.ultraedit.com) and crop the first 2 lines and save is at
nk.nb0
And try flash with Multi-Port/USB TTY Ver1.11a (mtty MFC Application HTC)
But the USB Connection dont work, the program make fail....
I have try with Remote USB Update v1.1 (host11.exe)
the program say Lost USB Connection.....
Is here any forum members to fix the problem......
Thanks in advance
[email protected]
IT Help Runner, Denmark
Hi...not sure if I'll be able to offer any insight...
I've an iPAQ h5550 too & have managed to successfully update to the latest ROM & firmware available.
From my recollection, they are all cab files.
Upon running the exe files you downloaded, it will unpack into a local directory & subsequently transfer the cab files to the iPAQ via AS.
Then, you should watch the screen for instruction & follow them to complete the update.
These are updates...not upgrades so they do not need the iPAQ to be placed into bootloader mode.
I think with 5550, they do away with bootloader mode to update the ROM or firmware. Very similar to the Jornada range.
Did you try hard resetting the device?
Simultaneously pressing the iTask, Calendar & reset buttons for 10 secs will do the trick.
Here's the link to the info: http://www.ipaqrepair.co.uk/ipaq_battery.php
After the hard reset, you will have to perform the updates in the right order to bring the firmware to version 1.10 & ROM to version 1.10.
If I'm not mistake, it should be as follows:
Firmware update: 1.00.18
ROM Update: 1.10
Firmware update: 1.10
Hope this helps...
How to flash 612c WM6 become WM6.1 i did download 2 Roms in sable's thread and i flash it. Every things is fine after completed i check it on ABOUT it's still the same window mobile 6 pro. Can anyone give me a solutions how to flash it to become wm6.1 thanks.
Information in HP asset viewer.
- ROM date : jun212008
- ROM revision : MP-1.01.04
- OS version : 6
- Bootloader version : MP-1-01.05
Try this:
http://rapidshare.com/files/174859341/614c_WM6.1_20270_v1.4_rev1.1.rar.html
Pass: israpda.com
Thanks for reply.. but i need some help, just now i check through the flash guide i dl the prophet tools i try to do it but it seems like not working..
error msg : file not found
it's my 1st PDA, if possible can someone advised me what's the right tools to flash it thanks.
Do not use larger SD-card then 2Gb.
Format the card for FAT.
Copy the flash.dio file.
Power off the phone. Battery must be full.
Insert the card.
Push the mute+record+power buttons simultaneously.
The firmware upgrade will start automatically.
That's all.
Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal
Good job, thanks!
Will try it out later!
is it still compatible even though my device SKU IDs is not compatible with the update?
Last time i tried i almost bricked my device.
In theory, yes
Actually, like I wrote above.
My ipaq 914c is Italian version.
It means that the SKU IDs of the phone is not not compatible with the update. ( I mean the official update!)
But we all know that there is no difference in the hardware between the ipaq 91x.
So any language ROM versions can be used on the another ipaq 91x phone.
=> WWE ROM can be used on any Ipaq 91x phone.
My Ipaq now is in English. But the SKU IDs still show that it's in Italian.
By the way, I forget to thank: Z!L0G80.
i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx
AbsolutBenz said:
i just tried to update my 912c using HP update utility that i downloaded from mediafire.
but it failed it gave me Code 402 : Cannot Communicate with device. and the device stuck at boot screen with RUU... on top of the screen.
- i already Hardreset the device
- i'm using Benjaminries Motherload ROM
- i'm using Windows XP
please tell is there somethings wrong?
i really want to try the update. should i try using SDbootloader? can you helping find some solution?
many thx
Click to expand...
Click to collapse
Hi,
As it was given like that, I think you should check the usb cable. Sometimes the cable is not working well. I use the original cable, because the last time I use another there was an error when it was flashing. (I'm not sure if the active syn is necessary. In my case, I have the active syn on my laptop. XP enviroment.)
If you want to try the SDBootloader you can find in this forums some instructions about cutting some bytes to obtain the flashdio.nb0
But I really don't recommend that way. Because the last time when I find the way to change the language by flashing the english Rom following those instruction. My phone was bricked. So I tried to find another way.
And this is it.
I think this method is the safest way for newbie. As I wrote above. The first time I bricked my phone. But I did the same procedure again. And it worked.
Just check the procedure again.
Good luck,
For the SDloader update (Which works very very well on my German 914c):
download the file below (I already cut the first 3432 bytes from it), put it on a newly formatted SD-card (not SDHC!) and hold down volumeup+OK button (the one on the right side) while pushing the reset button, hold the mentioned sidebuttons until you see SDloader. Then wait for a few minutes, and the update will finish!
If the updater does not find the file, you have to re-format the SD-card to either FAT or FAT32!
Rename the file to FLASH.DIO when you copy it onto the SD-card!
http://rapidshare.com/files/236053650/FLASH.DIO.html
vragon said:
Hi everyone,
I offer you a safe way to recover your bricked ipaq or just change language into English.
I use the lastest official english ROM download on Hp website.
I saw some members have the ideal to patch the ROMupdate.dll to bypass the check the language of the phone ipaq 61x.
It means that we can update the phone with any languages.
I do exactly the same with Ipaq 91x.
So I upload the file for you.
Just download, extract and run hpRUU.exe
Follow the instruction and after about 20m.
You have the phone
P.S: I used this method to change my phone language from Italian to English successful. And recovery my friend's bricked phone.
But notice that I'm NOT responsibility for any damage with your phone.
Good luck
Download the rom here
http://www.mediafire.com/download.php?jyzy00y2yal
Click to expand...
Click to collapse
Hi Everybody,
@vdragon
1- what a great job, guy!
2- in reality, i have already flashed your ROM successfully for my ipaq 914c, which is a native italian version. Since the incompatibilites of different versions were resolved perfectly.
3-Grazie tanto di nuovo
I'm pretty new with this and I've been trying to update my 910 with original ROM but for some reason it gets stuck and the only way to bring it back is with a SDLoader I downloaded from here but that one is very simple and I'd like one with all the programs.
Is there a way to load yours on it through the SD card?
you can follow the instruction to cut the 3432 bytes and flash your phone with SD card.
I see that many people prefer to use the sdloader method than this one.
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.
vragon said:
...
But the positive point of this method is that it updates all your firmwares include OS, WAN, Radio... to new version. Not only OS.
Click to expand...
Click to collapse
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?
congtiger said:
Hi all,
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Anybody has idea on the contrary?
Click to expand...
Click to collapse
sure
congtiger said:
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
Yes it is true!
Using vragon's patched Updater the following is updated:
OS (=ROM)
Bootloader
Pre-Bootloader
Radio&Modem
This update takes about 20minutes, so be patient, do not remove any cables during update!
The flashing of FLASH.DIO with an SD-card "only" updates the OS (=ROM) and is done within less than 10minutes.
Thanks vrago for patching the Romupdate.dll!
You can also see it in the bootsplash screen. Before the update (even after SDloader updates) it always showed FW 1.04.
Now it is 1.09 - and yeah, it works GREAT and quick!
I can recommend it!! (I do not take responsibility though)
Should be a sticky!!
I've been trying this file, and I get an error at 51% of update. Any ideas?
I think it's about your cable. Be sure that you use the original cable with the anti-noise hub.
If you didn't success the first time. Try it again.
Do as you did the first time.
And just be patient. Don't move anything.
The first time I used this method, at the middle of flashing, I kicked my cable and it just stopped. And I did it again carefully.
So that's it
Actually, I think I figured it out. It seems that Vista treats USB partnerships differently than XP, so after a certain amount of time, it "refreshes" the relationship with the USB device. If you are trying to flash your phone, that stops the flash/update.
I just used my XP system, and it worked fine. After a few registry tweaks for ring volume and battery life, it's working fine.
Are you really sure that the method of using SDloader has NOT updated Modem, Radio ...so on ?
Click to expand...
Click to collapse
I'm positive the SD Loader method isn't as thorough as this method. This method takes 20 minutes or so, and you can see that it's updating the pre-loader, modem/radio, etc. The SD method only updates software.
Problem using HP 614c from original ITA rom
I am a stupd guy
I am a stupd guy
I am a stupd guy
Hy vragon, i have used your method to upgrade my device 614c (and not 914) from an original Italian ROM. All process is ended correctly, all upgrade are finished without errors.
The update utility has made the update of that:
Software - From Version - To Version
Bootloader - 1.00.07 - 1.01.01
Windows Mobile 6.1 Professional - 1.00.07 - 1.01.01
Pre-Bootloader - 1.00.07 - 1.01.01
iPAQ WAN Radio Firmware - 0.81.00 - 1.09.00
But after the upgrade, at the end the display was black(not really black i can see the leds of the entire display are ON but das not appear nothing), and after some minutes abouth 20, i removed the battery and restart the device but nothing has changed. The led over the screen and the sound working.
I have try also to do a hard reset with a flash.dio on an SD card inserted to replace the Rom, but dose not work!
The device after that will work properly, and das not appear to have any problem.
CAN SOMWONE HELP ME !!!
@ilconte81:
just go to hp site.
find a ROM update for 614c.
download it.
using winrar to extract everything in the exe file.
copy the ROMupdate.dll from my file to replace the file in the folder which is extracted from exe file.
run the rom update again.
Tanks for reply vragon,
i have tryed to do what you wrote, but the device will not be right recognized from the OS (will appear USB device not recognized) and the update utlity after a long time in "Plese wait while the device state is verified" give the comunication error Code 402, Cannot comunicate with device.
I use the original cable and try these on different OS like Win XP and Win 7.