Related
When I plug my MDA Pro into my PC it draws 460mA of current at 4.75V and the orange charging light always comes on.
I have bought a car charger - when the MDA Pro is plugged into that it also draws 460mA at 5.04V but the Pro doesn't always seem to realise it is being charged - the orange charging light doesn't come on and the backlight switches off so I cant see the SatNav! (when the light goes off the current goes down to 430mA)
The charger was bought of eBay from shop4hardware/PCglobe for £9.99 and it looks well made.
Any ideas what is going wrong? Has anyone got a 12V charger they are happy with - if so where did it come from and how much??
ceemjay the tight fisted
I bought a car charger off eBay, and while the orange light does come on and stay on, it doesn't seem to charge very effectively. If i'm using something like TomTom the charger manages to keep the battery charge level just about constant, rather than building up charge.
Is this a problem with the Universal? I had a Blue Angel before the Universal, and the car charger I had for that was very effective.
Cheers
Rowan
I had this problem too and solved it by purchasing an "orange" (UK mobile phone operator) branded charger for 10 quid from one of their shops. I have no issues now.
What i did notice when I had the problem was by ensuring the xda was off prior to plugging in the old charger, it would continue to stay orange when turned on. I think this problem is a common one with the usb cable & car charger adaptors combo.
i bought one from expansys, what i noticed:
1. It takes a lot of jiggling, pushing, pulling and twisting to get it recognised by the device (organge light on)
2. When it charges, it does so slowly, i think about 1% per 10 minutes or so, or about 10% per hour.
My two bobs worth anyway.
Many of the mini USB car chargers are simply not powerful enough to charge these devices. They all have the same voltage but the amps are different. I read somewhere that good M5000 car chargers should be rated at 1amp, I'm not sure about this but I've certainly had trouble with ones at around 600mah.
With the under powered chargers you often have to plug them in while the device is switched off. Even then it's not going to charge as well or as quickly. Getting them to start charging without turning you device off is just down to luck and patience.
My advice is to look for chargers that are specific for the M5000 etc. If it also mentions Motorola phones etc, then it's not going to have the required power output.
I hope this helps...
I bought an ORA one from a service station (phone bitz type shop), it was a bit expensive but I needed one in a hurry and you can test them in the store.
as per my earlier post - m5000 is orange branded htc universal, aka o2 xda exec. I believe mine stated it was for the spv500 and it still worked fine...
The universal wants a 2 amp charger really. the 0.5 amp from most chargers including USB ports just is not enough to do much more than stop your battery draining whilst your universal is in use !! other useful alternatives include the charger meant for the newish blackberry
Thanks for all the comments.
The charger that comes with the Pro is rated at 1A however I believe the USB spec only allows up to 500mA to be drawn (as I orginally posted it draws just below that) and I have never had a problem with charging via USB. Hence my confusion!
Is the charging software controlled and might there may be a bug which manifests itself under circumstances?
Clive
The Brodit active holder charges the universal first time everytime, and is a very good place to store the phone on the move. I've got a 3.5mm input on my car stereo and use my phone as my in car music source. If I could get a 3.5mm 4 pole to 3.5mm stereo plug and breakout mic it would be perfect since I could use it as decent handsfree solution, voice command can still use the built in mic when the stereo connection is inserted but the phone app doesn't.
The Brodit holders are nice. I prefer the unpowered version, so I use a separate charger cable. But I agree good holders.
Since I upgraded my Trinity using the official HTC rom update I have found that my device will not charge when it's in the brodit active holder in my car. The orange light comes on as if it is charging but when i check the power status i note the power drop over a period of time.
The device will charge without any problem when it is connected to my PC via the usb cable, it also charges without any problem when i use the mains power adaptor.
Initially I thought perhaps my brodit was faulty so i bought a new one, still i have the same problem.
Any suggestions from anyone?
Thanks,
Robert
I recognized very slow charging with my device over USB in comparison to my older PDAs. The reason must be something with the available current over USB (max. 500 mA). Maybe this is also the reason for your problem with the Brodit holder.
Try a separate car charger. They are available quite cheap with a standard USB plug.
Wookie said:
I recognized very slow charging with my device over USB in comparison to my older PDAs. The reason must be something with the available current over USB (max. 500 mA). Maybe this is also the reason for your problem with the Brodit holder.
Try a separate car charger. They are available quite cheap with a standard USB plug.
Click to expand...
Click to collapse
Hmm, this is a question that needs answering. On my Prophet I could plug it into my car 12v cig with an 850mah usb adapter and it would power the device for navigation and also charge it at the same time. Now with my Trinity, it seems to have a hard time keeping up, so I bought a new high powered adapter (2,000mah). It still doesn't seem to be charging very fast although it seems to be able to keep up with the device power usage. Is there a charging problem with the Trinity with some roms?
After trying multiple car chargers, most of which wouldn't even power the charge light on my Trin let alone charge the battery I opted to spend a few quid and bought the Carcomm CMPC-96. It works a treat and charges the battery very quickly even when i'm running tomtom and making and taking calls at the same time. I can't figure out why my brodit holders wouldn't produce enough power to charge the battery but this Carcomm product is the Dogs !
I bought a Brodit Carholder (without cigarette lighter plug) and when i put the TytN II in it the batterycharge lamp blinks but the battery don't really charge.
So I send the Brodit active carholder back for RMA. Yesterday I received a brand new one this time with sigarette lighter plug. But I have the same thing, charging lamp blinks, even the system/energy says the TytN II is charging, but he isn't really.
I did also a hard reset but the result stays the same.
I also marked 'charging with computer connected' on and off.
Brodit tells that my serie is not affected with the bug like in the sticky post in this forum.
I have also a standard cigarette lighter plug with standard mini-USB 5 volt output and this thing works great. The TytN II charges very fast then. Also connected with my computer it charges fine, and also with the included normal 220V/5V charger. Just with the Brodit carholder it does NOT charge.
All tests (except the normal 220V/5V charger) in the same car of course.
Should I try a third carholder or is it possible that there is something wrong with the USB port of my TyTN II? (I guess not because it charges good with a normal standard cigarette mini USB charger ... ?)
I'm desperate. Thanks for any advises!
Johan
Vervaeck , see my post over at modaco http://www.modaco.com/content/HTC-Kaiser-Kaiser-MoDaCo-com/261974/Major-Car-Charging-Issue/.
Not sure what's going on, but there's definitely something not quite right.
answered here:
http://forum.xda-developers.com/showthread.php?t=343951
nm8: that supposes that the phone does not charge at all, not simply not through the brodit. There seems to be an issue with some car chargers not charging the handset. Read my post over at modaco to see what I mean.
@squiggs1982
Wow, seems I'm not alone. Weird that some TyTN II's seems to work with Brodit, others don't. But on your link I found indeed the same problem described, but NO solution, or am I wrong?
@nm8
Sorry, but I read very well that sticky post and before I mailed to Brodit with my serial and they answered that it was no problem with my serial nr.
It is also not a question of power capacity, I tryed the brodit with a labo 5V 2A stabylasid transformator. It was not working either. 2A is for sure enough.
(excuse my bad english)
Strange, i just installed my BRODIT carholder (no cigrette lighter version), and it charges perfectly. Orange light glows, and the icon shows its charging.
vervaeck said:
I bought a Brodit Carholder (without cigarette lighter plug) and when i put the TytN II in it the batterycharge lamp blinks but the battery don't really charge.
So I send the Brodit active carholder back for RMA. Yesterday I received a brand new one this time with sigarette lighter plug. But I have the same thing, charging lamp blinks, even the system/energy says the TytN II is charging, but he isn't really.
I did also a hard reset but the result stays the same.
I also marked 'charging with computer connected' on and off.
Brodit tells that my serie is not affected with the bug like in the sticky post in this forum.
I have also a standard cigarette lighter plug with standard mini-USB 5 volt output and this thing works great. The TytN II charges very fast then. Also connected with my computer it charges fine, and also with the included normal 220V/5V charger. Just with the Brodit carholder it does NOT charge.
All tests (except the normal 220V/5V charger) in the same car of course.
Should I try a third carholder or is it possible that there is something wrong with the USB port of my TyTN II? (I guess not because it charges good with a normal standard cigarette mini USB charger ... ?)
I'm desperate. Thanks for any advises!
Johan
Click to expand...
Click to collapse
Try this
TYTN users (Hermes) have a similar issue where the phone charges intermittently from the car charger. Usually if you do a soft reset it starts to charge but not always. My imate branded Hermes has this issue but the europeon equivalent does not - figure that out? Anyways, I bought the following to resolve it: http://www.pocketpctechs.com/main.asp?unit=i-mate_JASJAM-650&area=accessories-lil%27+sync%AE+cable+accessories&item=LSP%2DDUOADPT01
I just bought the Kaiser yesterday and will report back how it behaves to verify the above.
I had a similar issue with my brodit active holder in one car I used.
Instead I got the passive brodit holder and did my passive to active mod on it using a 3-in-1 splitter and an HTC car charger. Works perfectly in all cars I have tried it in so far.
I think it is an issue to do with your alternator not being earthed properly or something. Do you have an aux in on your car stereo? If you do and you plug the Kaiser in to the aux socket and play music on the Kaiser, do you hear a whine through the speakers when you accelerate? If so, look up "Alternator Whine".
Okay turns out, my Brodit charger is NOT charging at all.
IT shows that it is charging, but does nto charge the battery one bit. Using the AC adapter charges, as does the USB cable on my computer.
Waht the hell.
This post is not specific to TyTN II but it might be true for it:
http://www.4winmobile.com/forums/hermes-black-rom-support/11607-black-satin-problem-car-charger.html
I installed a Brodit active carholder today (fixed install, not the cigarette lighter one) and I'm also not getting charge. Only difference is I'm not getting anything...orange charging light on the phone doesn't turn on, battery icon doesn't show charging.
My phones charges fine using USB cable on my PC so it shouldn't be the blown USB port issue.
The green light on the Brodit charging box is on. If I measure power on the pins of the 6 pin molex connector, I get 5.34V on the red wire and 5.30V on the yellow wire. I get no voltage on the other three wires. Is this right? The 4pin Molex is not used, right?
Fourgig said:
I installed a Brodit active carholder today (fixed install, not the cigarette lighter one) and I'm also not getting charge. Only difference is I'm not getting anything...orange charging light on the phone doesn't turn on, battery icon doesn't show charging.
My phones charges fine using USB cable on my PC so it shouldn't be the blown USB port issue.
The green light on the Brodit charging box is on. If I measure power on the pins of the 6 pin molex connector, I get 5.34V on the red wire and 5.30V on the yellow wire. I get no voltage on the other three wires. Is this right? The 4pin Molex is not used, right?
Click to expand...
Click to collapse
Thats correct. The 4pin molex is for GPS modules requiring power.
I was waiting until the new year to check back with the person i bought it from to figure out what the hell is wrong with this thing.
Got off the phone from the representative for proclips, and they are talking to sweden.
Looking forward to resolution.
I submitted a support email a few days ago and I'm waiting for a response from them. Will probably give them a call tomorrow though. I figure if they get a bunch of calls about this issue, maybe it will light a fire under their butts and get them to resolve this quickly.
Hello, I've just bought an emergency charger for my Kaiser. It takes the power from an AA battery and gives the USB voltage in the output. It works great with my Mio A 501, but doesn't work at all with the Kaiser. I did a quick search and found this in a discussion about car chargers:
Are you using the HTC charger or an OEM one?
The HTC charger works all the time the OEM ones don't - the reason being that if you use a normal Mini USB cable, the handsets will only take a charge if there is an indication of a data connection (either than gprs or the cable) - otherwise it won't take a charge.
You can apparently solder a couple of wires together on a normal mini USB cable - but I wouldn't know where to start on that!
Click to expand...
Click to collapse
Now I've already heard of that, for example, a Play Station Portable needs the data wires in the USB grounded in order to charge. Is it the same with Kaiser? (putting three wires together isn't a big deal) Or is there an easier way how to make it charge?
So, I gave it a try and soldered the data wires with the ground wire. But when I try to charge the Kaiser, a yellow led starts to glow (which it didn't with the original cable) and, after a minute or two, the led goes off and Kaiser stops charging. When I turn the Kaiser off and then plug the cable in, the yellow led doesn't go off. However, when I turn Kaiser back on to check the battery meter (after about half an hour), I find out that the battery didn't take any charge at all. So, could anyone tell me what the problem is?
thanks, Mike
PS.: Adding some photos of the wires...
Probably because of the voltage...
Hey!
Have you checked the output voltage of this charger? Standard charger outputs 5V. If yours outputs less - the battery won't charge; if outputs more - you may "burn" your PDA chipsets
5V - 5.5V is safe range.
I found this on thinkgeek.
http://www.thinkgeek.com/gadgets/cellphone/b43f/
It says for iPhone, but sure it would work just fine with other devices that have issues.
had a same problem but using it in the car...
when i got my tytn2 i immediately bought a car charger and the salesman told it's an original one, said output 5v 1A.. when using in the car it charged for a minute or two and went off... than i got from ebay a micro usb 1A charger (used for iPhone too) and tried in the car-> it work flawlessly
I am facing a problem with my SmartPhone HTC Touch hd T8282, I had it working with no problem, everything was just great about it. Suddenly today when i went out i picked it out of my pocket and i saw it was off, since than it did not turn on at all, there is no sign of charging when i plug it to the power.
Please help me on this.
If you can't still charge your phone, buy a universal lithium battery charger similar to this one:
http://www.bestofferbuy.com/universal-cell-phone-lithium-battery-charger-with-usb-power-port-ac-110v240v-p-26225.html?SSAID=389818&utm_source=shareasale&utm_medium=affiliate&utm_campaign=affiliate1
When you receive the charger, you will need to adjust the two posts so they make contact with your battery's terminal contact points. Connectivity will be indicated by the tell-tale lights coming on green. This universal lithium charger can be used via a USB connection or alternating current (a/c). I'd recommend using a/c.
These chargers cost less than 2.60 USD either at this Chinese vendor or on eBay. I have three of them (one in the office; one at home and another in my travel bag). They work great!!!