Related
i'm having a problem that i can't find much information on.
i have a verizon audiovox utstarcom xv6700 (htc apache)
i drained the battery one night, to the point of what seems no return.
whenever i plug in the phone, a solid red light comes on.
whenever i plug in the phone without the battery inserted, a flashing red light comes on.
whenever i instert the battery in the base that came with the phone,
the charging light flashes yellow and then turns green.
i haven't installed anything more than software trials seeing as i just bought this phone.
if i can find a fix for this, without having to go through waranty issues, it'd be much appreciated.
any help?
thank you everybody!
When the battery is completely drained, the charging light should turn on and be red. How long did you try to charge it? You have to leave it plugged in for a bit to get enough charge to get past the red light.
retry
unfortunately,
i have already tried this.
i leave it plugged in for aprox. an hour,
and the red light dissapears.
however nothing happens after that either.
i unplug it, and plug it back in,
and the red light reappears.
any other suggestions?
I have one, bring it back and get a new one. did u buy it from a official dealer?
no,
i bought it off of a guy who had it for two weeks and didn't think it was worth the money.
he did buy it from a verizon store brand new,
and like i said i've only had it for a short period of time.
i was waiting to see if i could find a fix without sending it back,
to do without getting the reciept information required for the warranty.
i've read about other htc products having problems with this,
and everyone says that there is a problem,
like mentioned before, that once the battery is drained,
it doesn't have the "juice" to start charging again.
alot of people have recharged it with batteries.
i'm planning on finding my voltage reader (whatever it's called)
and seeing if it's the batteries dead.
other people have said that there is a problem with bad data ports.
which could have been from the previous owner,
they say that after drops that a few weeks after the drop it goes out.
any other suggestions?
thanks guys!
The red light can indicate battery fault. Remove the battery and clean the contacts, then try charging in the back of the cradle rather than using the USB connector. It might come back. Fully discharging is not good for the battery, so if it comes back, listen to the phone and charge it went is says the battery is low (20%???). Other than that, batteries are cheap, try a new one.
SITUATION
My Cingular 8500 does not power on. I have tried connecting it to wall charger as well as USB cable. The red or the orange light also does not come on. I tried all resets also but nothing worked.
BACKGROUND
a. My phone suddenly went off when I was opening the sliding keyboard. It had a decent (60%) charge at that time. After this it refuses to come on.
b. Only addition to the phone in the last 3 months has been a 2GB MicroSd Card. I inserted this card 4 days back and it was working fine.
c. The device is around 6 months old (but its unlocked, running WM6 and does not have any warranty)
d. I have been using the original wall charger to charge this phone regularly.
HELP REQUIRED
1. Is there a way to check if the problem is with the battery or with the phone? I do not have a spare battery.
2. Should any light come on if I connect the phone to charger without the battery inserted in it?
Thanks!
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
i have the same situation going on ... except with mine the screen faded out...it came back on once...and faded out again and will not turn back on.. when i put it on the charger it was a red light.. and will not turn on or soft reset, or enter bootloader or hard reset. .. in addition i tried the method above and nothing has worked.... any other suggestions...my phone was working fine when this happened out of nowhere... i dont have insurance either i bought the phone from someone off of craigslist..help is greatly appreciated
I am having the exact same problem, I had about 30% charge, then it just shut off, and now will not come back on under its own power or via USB nor charger. I tried connecting the charger then inserting the battery, but I do not get any indicator lights at all.
I was running WM6, and the most recent thing installed was the pointUI home screen replacement app.
has anyone experienced this before?
theconcon said:
SITUATION
My Cingular 8500 does not power on. I have tried connecting it to wall charger as well as USB cable. The red or the orange light also does not come on. I tried all resets also but nothing worked.
BACKGROUND
a. My phone suddenly went off when I was opening the sliding keyboard. It had a decent (60%) charge at that time. After this it refuses to come on.
b. Only addition to the phone in the last 3 months has been a 2GB MicroSd Card. I inserted this card 4 days back and it was working fine.
c. The device is around 6 months old (but its unlocked, running WM6 and does not have any warranty)
d. I have been using the original wall charger to charge this phone regularly.
HELP REQUIRED
1. Is there a way to check if the problem is with the battery or with the phone? I do not have a spare battery.
2. Should any light come on if I connect the phone to charger without the battery inserted in it?
Thanks!
Click to expand...
Click to collapse
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
Eamonn said:
I am having the exact same problem, I had about 30% charge, then it just shut off, and now will not come back on under its own power or via USB nor charger. I tried connecting the charger then inserting the battery, but I do not get any indicator lights at all.
I was running WM6, and the most recent thing installed was the pointUI home screen replacement app.
has anyone experienced this before?
Click to expand...
Click to collapse
It wont power on threw charger without a "good" battery plugged in.
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone. If not just go to ATT wireless store and see if they have one you can try and buy.
demo23019 said:
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone.
It wont power on threw charger without a "good" battery plugged in.
Click to expand...
Click to collapse
I really hope thats the problem because it's an easy solution, otherwise I fear it might be toast. thanks for your advise
No light when connected to charger
Thanks all for your responses!
markafreeman said:
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Click to expand...
Click to collapse
Dear Markafreeman, I tried the entire routine above but no help.
demo23019 said:
The Power LED should light up "red" other than that your wont get any juice. And read my second reply, try radioshack
It wont power on threw charger without a "good" battery plugged in.
Sounds like u might have a bad battery. Happend to a friend of mine "different phone" just go to a local Radioshack If they have your type of battery and have one in stock they will most likely let you try one on your phone. If not just go to ATT wireless store and see if they have one you can try and buy.
Click to expand...
Click to collapse
Dear demo23019, I am not sure if I understand the above correctly. Should the Power LED light up "red" when battery is not inserted?
Once I connect the phone to charger (wall or USB), without the battery inserted in it, no red light comes on.
Does this mean that there is some problem with the phone hardware?
theconcon said:
Dear demo23019, I am not sure if I understand the above correctly. Should the Power LED light up "red" when battery is not inserted?
Once I connect the phone to charger (wall or USB), without the battery inserted in it, no red light comes on.
Does this mean that there is some problem with the phone hardware?
Click to expand...
Click to collapse
Yea the power LED should light up red with out a battery plugged in. Check the usb plug on the bottom of your phone, make sure the middle piece inside is still there and didnt break off.
demo23019 said:
Yea the power LED should light up red with out a battery plugged in. Check the usb plug on the bottom of your phone, make sure the middle piece inside is still there and didnt break off.
Click to expand...
Click to collapse
Oops. My phone's power LED does not light up when I connect it to the charger without the battery inserted in it.
I have checked the following :
a. usb plug is fine (I checked it by plugging it into the Y cable for the USB charger. The LED on the Y cable lights up when I connect the USB plug into it
b. The middle piece inside the socket at the bottom of the phone is still there and shows no signs of damage.
c. The wall charger is also working fine.
Does this conclude that the phone has a hardware fault and this is not linked to the battery being dead?
Similar Problems
I just had the same problem. I had it happen to my Att Tilt and then to my cingular 8525. You should check out this thread and maybe post your info there too, it would be nice to see everybody post in the same thread so we can figure out what's going on.
http://forum.xda-developers.com/showthread.php?p=1783005&posted=1#post1783005
yh
yh i got the same problem, i touched the power button so it wld go into standby, and it then refused to turn back on, even when i soft resetted it. Plugged it into the wall charger without the battery and there is no red power light coming on.
I've got a MDA Vario II and though im gettin a replacement, it kinda sucks as it seems im gna lose all my data
can we try to determine in more detail what people installed before they experienced this?
I just pulled it apart, and cleaned the inside to no avail, nothing seems to be awry, atleast not to my untrained eye, however it did get me thinking.
I listen to music on my tytn all the time, and over time the usb connector has become quite loose, frequently losing connections over activesync and music comes and goes from both lef and right. if the USB connector is shot, then when I plug it in it won't register that there is power, nor will it have the power to light up the red light indicating there is no battery. also, if the usb link is shot, then the phone wasn't charging so my battery is likely dead.
now to test this out I need to have a verified 100% charged battery.
I currently have the same problem. It will not charge via wall/usb. It flashes red once and that's it. Without the battery and plugged in, I get a solid red light. I tried plugging it into the wall charger without a battery and then putting my battery back in. The red light just turns off. That's it. I can get an active sync connection with a dim white screen, but I do not have enough juice to try flashing a new rom. If anyone has issues like these, are you also able to get an activesync connection?
TIA
EDIT: Is it possible to bypass the low battery protection when flashing a rom? My battery is somewhere around 40% so it would be safe.
Update:
Okay, I purchased a new oem battery and a battery charging dock. This way I can charge the battery without the phone before I attempt to flash a new rom.
I still would appreciate it if anyone who has seen these symptoms (white screen BUT with lots of vibrating / no charging / no bootloader) could give me a few pointers. I've exhausted the Wiki and so far it seems my only option to save the phone is to flash a new rom. Thanks in advance to anyone willing to give me some advice.
Hi everybody
I have a problem with my Galaxy S5 (no custom rom, official)
I normally used my phone, I locked it. But, after about 10 mins I tried to unlock my phone, but nothing happens
I tried to reboot, nothing happens. I tried take out and put the battery - nothing happens. So I searched on Google and tried some keys combinations, but nothing happens. My phone has about 80% battery. I tried to charge it in the charger, but nothing is happening (black screen, no notiffication light). Also I tried to put off my SIM and SD Card, but nothing happens
Do you have some skills in it? Can you help me?
Few days ago, I faced the same problem..
http://forum.xda-developers.com/showthread.php?t=2853472
Then I'd to take it to the Samsumg store.. And they return it back in 2 days and said me it was a software problem..
I wanted to do a recovery reset, but i can't boot my phone anymore, also the Kies doesn't see anything, so. Did you really think that is a software problem? Because my phone won't vibrate at boot. So maybe it can be a hardware prob :/
EDIT: Phone started blinking red light... (nottiffication), I tried to charge it, but nothing...
Mate as mentioned early, same problem I faced..
It'll be better, if you return it to Samsung customer care..
You seem to be saying that the problem occurred unexpectedly. So presumably this isn't subsequent to a flash error, newly installed app or a trauma (dropping the phone, etc).
First ensure that your battery is charged, plug in the phone to a charger as well and try turning it on. If at all possible, borrow a battery from a friend's S5 or go to a store and borrow a battery for 30 seconds to confirm that the battery isn't the issue.
If the problem persists, then remove the cable and battery. Then put the battery back into the phone and press and continue to hold in this order, the volume down key, then menu key, then power key. Hold all three until the screen powers up (about 5 seconds). If this doesn't work.. the most likely problem is a damaged power key - try pressing hard or "wiggling" it to see if that makes a difference.
If you still can't start the phone, then see if a local cellular repair shop has a "jtag jig" that you can borrow. Or you can buy one on Ebay for a few dollars. When this jig is plugged into the USB socket, the phone should automatically restart.
If all of the above fails (which is unlikely), you would seem to have a hardware problem or unknown origin. Which would be very unusual. If your phone is under warranty, make a claim. Otherwise get an estimate to repair it.
.
If I hold all 4 buttons at the same time and connect the phone to PC, PC recognises the phone for a few seconds. Well, maybe not recognises, I cant see it, but it plays the same sound as if connected flash drive to pc. However, everytime it disconnects within a few seconds...
I´m in the same case, but I was flashing the Galaxy S5 with the four files ROM and the pit file using Odin3.09. All the process ended well, but after rebooting there apeared one Screen sayin something like "Some files at this phone are encripted and there can´t be modified......." so I did a manual reboot and take off USB cable and from this moment the phone don´t do anything but giving a sound when I plug USB to computer cable and I can see new COM --> Qualcomm HS-USB QDLoader 9008, and there repeat a loop.
I´m still looking for a solution, but it gives me that there is time to change phone.
Possible Fix
This thread is old but idk if this was ever solved, so in case anyone else ever has an issue like this. My Gf is still rocking this phone so i've had a little experience with it. The phone wont turn on or charge. I got it to work by sticking a flat head screw driver and prying it fairly hard against the bottom of the battery (the side closest to the charge port) and forcing the battery harder against the metal contacts. While pushing the battery I turn on the phone and it starts right up and continues to run even after letting the pressure off. I've noticed this happens every few times i take the battery out, but this method has never failed for me turning the phone back on. Hope someone finds this helpful.
kimo hands said:
This thread is old but idk if this was ever solved, so in case anyone else ever has an issue like this. My Gf is still rocking this phone so i've had a little experience with it. The phone wont turn on or charge. I got it to work by sticking a flat head screw driver and prying it fairly hard against the bottom of the battery (the side closest to the charge port) and forcing the battery harder against the metal contacts. While pushing the battery I turn on the phone and it starts right up and continues to run even after letting the pressure off. I've noticed this happens every few times i take the battery out, but this method has never failed for me turning the phone back on. Hope someone finds this helpful.
Click to expand...
Click to collapse
weird, youd think that bending the tabs out to force contact with the battery better would do the same trick fwif
So, I plugged my Nexus 4 into a generic car charger and it went black instantly. The battery was at about 92%. With the hope that a proper AC or computer USB charge connection would bring up the white battery icon and fix things, I stopped by an out of town T-mobile. The manager tried the button battery-reset (up volume + power for 60sec) and I googled alternatives and tried the - enter recovery by pressing those buttons for 15sec off the charger and connecting while still holding down the buttons - trick. Neither worked.
The manger seemed familiar with that and the other button pressing tricks, and said that really, my only real hope would be to reset/replace the battery, but that would void my warranty. However, although the T-mobile site claims my Google bought phone is under warranty (and I've been paying for it each month), technically, it isn't. Under them or Google (any more). So, I purchased the tools to open the phone, as well as a replacement battery. In the interim, I tried to use all the button combos and various charging connections to get it to come back to life. I *did* manage to get it charging the old battery. I know because the blinking red light turned constant for an hour or two, and the battery got warm. I can only guess that the battery was too damaged to keep the charge however, because I could never get it to turn on during or after. My best guess is that the software battery reset allowed the phone to send a charge to the battery - at least once.
After getting my tools and replacement battery, I managed to get the phone open (with great effort - I think there must be a difference between batches there). I removed the old battery connection and looked to see if I could get the charge icon with it unattached and on the charger. I couldn't. Reconnecting the old battery didn't seem to make any difference.
I was about to go through the process of prying up the old battery when I realized that you can actually connect the new battery to the board connector without getting the old one out. So I did that. Leaving it charging like that for awhile didn't do anything, so I decided to do another software battery reset and I'm letting it sit on the charger overnight. All of this has been without reattaching the back.
So my major question is - does anyone know for sure if the phone actually charges the battery with the back off? I know there are important circuits there - which seem to shut down the phone after the battery or google image when not detected (at least that's my deducement after reading posts). But are those connections also used in charging? The Qi goes though the back to the charger function, so perhaps that connection has to be there? I would like to try and find out though beforehand. It took 2 hours and two mangled guitar picks to get it open the first time, and the second may be just as trying. (And believe me, towards the end, I was not concerned with being gentle.)
I am also curious about the four prong battery connection. I've seen the post about charging the battery using external sources by connecting to the two outer pins. Does that mean the two inner pins constitute a second circuit between the charged battery and the phone? And if I find another 3.8v battery fully charged, I could perhaps connect that to the phone instead by wires and get it booted into recovery? As to why I'd want to do that, I don't recall the last dated CM version I had installed, so finding that in their folder plus pulling off everything from /data... assuming I replaced this with another Nexus 4, I might be able to save myself a lot of setup hassle.
In terms of the red light... it actually seems to be an error code. When triggered, it blinks 7 times, and on the eighth stays lit for a bit before repeating.
cetkat said:
So, I plugged my Nexus 4 into a generic car charger and it went black instantly. The battery was at about 92%. With the hope that a proper AC or computer USB charge connection would bring up the white battery icon and fix things, I stopped by an out of town T-mobile. The manager tried the button battery-reset (up volume + power for 60sec) and I googled alternatives and tried the - enter recovery by pressing those buttons for 15sec off the charger and connecting while still holding down the buttons - trick. Neither worked.
The manger seemed familiar with that and the other button pressing tricks, and said that really, my only real hope would be to reset/replace the battery, but that would void my warranty. However, although the T-mobile site claims my Google bought phone is under warranty (and I've been paying for it each month), technically, it isn't. Under them or Google (any more). So, I purchased the tools to open the phone, as well as a replacement battery. In the interim, I tried to use all the button combos and various charging connections to get it to come back to life. I *did* manage to get it charging the old battery. I know because the blinking red light turned constant for an hour or two, and the battery got warm. I can only guess that the battery was too damaged to keep the charge however, because I could never get it to turn on during or after. My best guess is that the software battery reset allowed the phone to send a charge to the battery - at least once.
After getting my tools and replacement battery, I managed to get the phone open (with great effort - I think there must be a difference between batches there). I removed the old battery connection and looked to see if I could get the charge icon with it unattached and on the charger. I couldn't. Reconnecting the old battery didn't seem to make any difference.
I was about to go through the process of prying up the old battery when I realized that you can actually connect the new battery to the board connector without getting the old one out. So I did that. Leaving it charging like that for awhile didn't do anything, so I decided to do another software battery reset and I'm letting it sit on the charger overnight. All of this has been without reattaching the back.
So my major question is - does anyone know for sure if the phone actually charges the battery with the back off? I know there are important circuits there - which seem to shut down the phone after the battery or google image when not detected (at least that's my deducement after reading posts). But are those connections also used in charging? The Qi goes though the back to the charger function, so perhaps that connection has to be there? I would like to try and find out though beforehand. It took 2 hours and two mangled guitar picks to get it open the first time, and the second may be just as trying. (And believe me, towards the end, I was not concerned with being gentle.)
I am also curious about the four prong battery connection. I've seen the post about charging the battery using external sources by connecting to the two outer pins. Does that mean the two inner pins constitute a second circuit between the charged battery and the phone? And if I find another 3.8v battery fully charged, I could perhaps connect that to the phone instead by wires and get it booted into recovery? As to why I'd want to do that, I don't recall the last dated CM version I had installed, so finding that in their folder plus pulling off everything from /data... assuming I replaced this with another Nexus 4, I might be able to save myself a lot of setup hassle.
In terms of the red light... it actually seems to be an error code. When triggered, it blinks 7 times, and on the eighth stays lit for a bit before repeating.
Click to expand...
Click to collapse
I RAN INTO A SIMILAR PROBLEM
I found that holding the power button for a while allowed my nexus 4 running stock Lollipop 5.1 to boot back up.
Have considered that you may have a faulty USB port ?
Just pop the old battery out install the new one plug in the charger and it will charge. You can boot up without the back on. The back contains the antennia.... and the NFC circuit board.
Good luck
Blacksmith5 said:
I RAN INTO A SIMILAR PROBLEM
I found that holding the power button for a while allowed my nexus 4 running stock Lollipop 5.1 to boot back up.
Have considered that you may have a faulty USB port ?
Just pop the old battery out install the new one plug in the charger and it will charge. You can boot up without the back on. The back contains the antennia.... and the NFC circuit board.
Good luck
Click to expand...
Click to collapse
Well, still no luck. I ended up putting the new battery in and closing it up to try the Qi charger, but all I can get is either 7 or 10 red blinks followed by a short solid light. No white battery charging symbol or anything else.
When you say a faulty USB port, what are you referring to? The cable works (though I've also tried my Nexus 7 one too) and even though it won't boot, my computer does recognize that something is there when I plug my phone into it (it just can't figure out what's plugged in - which is normal). I want to say that it's trying and failing to charge the new battery. At this point, I think the charger messed up more than just the battery.
Let me start from the begining.
So the other day I plugged my phone into USB in order to charge it (I had to keep it close to me hence why I didn't plug it into the wall charger). The phone was charging, showing up as a media device on the lappy, etc. I was doing stuff on the computer then I heard it vibrate so I went to see what it was. The blue notification light was on (facebook notification most likely) and when I pressed the Menu button the screen didn't come on. I also tried the Power button but same thing. So I decided to restart the phone. Since then, it hasn't turned back on.
I tested the battery in another device and it's working perfectly fine. Neither recovery nor download mode work. I tried to do some of the tests people recommended for sudden death, like plugging it into usb and leaving it for a while, trying to kick start it (putting battery in while holding the recovery buttons) - you name it, i've done it. I even went to the lengths of taking off the back cover to see if theres any crap that got in there, maybe a loose connector, anything burnt - nothing. Unfortunately, I don't have a multimeter to see if there is a charge running through the board. Looks like sudden death to me, the only thing is - I rooted the phone on the 1st day I got it and I don't live in the country where I bought the phone so sending it over for warranty repairs would be a pain in the ass. What can I do? I would greatly appreciate your help, if you manage to help me fix my baby, I will ENSURE to send you a donation for a nice, big, cold beer (or maybe a few).
Looking forward to any answers! I really need my phone, I use it for work.
It seems like a hardware issue... you need to take it to a local store to scan it's hardware.... maybe something gone wrong while charging which made something be destroyed inside it..... hope its not the motherboard.....
it happens sometimes, when charging current fluctuate, it destroys the charging circuit and in result it damage the whole current circuit, local repair shop can solve the issue.