Related
Hello, earlier today i felt the device was very warm, i tried to switch it on but it dint respond, even to a reset. when i plugged it into the wall charger all i get is the right hand LED glowing red.
HELP!!!!!!!!!!! how do i hard reset it or get it to work again!!!!!!
i would call in orange care, but im out of the country and i really need the pda functionality!!!!
Unlucky. The 'red' light on most HTC devices indicates a serious power problem, usually it means that the battery is dead (as opposed to simply having run out of charge) or very close to death. You can probably get it working again with a new battery, if the incident hasn't damaged any other components.
i had this with my JJ after I accidently let the battery run down, I plugged it in and led went red and unit would not power on, left it plugged in started scanning the manual and web about a red led, 30 mins later, JJ just switched on and all fine.
It's worth a go and ive not had problem since
i dont think that was the case...
i have a feeling it might have been a short or something, because the unit was SERIOUSLY hot.....
nothing i did worked....until............
final time before giving up, the light was still red etc.
i figured what the heck, either way its dead and im going to get a replacement.
i then gave it fairly hard thump
the red light disappeared. i thought to myself, oh crap, i've really killed it.
then i reset it............. IT BOOTED UP!!!!!!!!!!!!!!!
and all my info still intact......brilliant.....im still going to try and get a replacement when i get back, but thank goodness.
and here i was thinking the last computer to respond to physical violence was the old 486'es hehehehehe
afhstingray said:
and here i was thinking the last computer to respond to physical violence was the old 486'es hehehehehe
Click to expand...
Click to collapse
Actually, it's called percussive maintenance, "the fine art of whacking a machine till it works"
hehe, i'm an IT technician and it's the first thing i try, especially with Printers.....
They don't teach you that on MSCA courses.....
I would recommend not using the machine too much until you can get a replacement battery if I were you. Lithium batteries will get very very hot (in some cases expand and ignite) if they are dis-charged too far. Most equipment which uses lithium technologies will have a voltage cut-off on the power input. As each cell is a nominal 3.3V-3.6V, this is often at around 3V in order to not discharge the battery too far. I would have hoped that this was a HARDWARE function rather than software. However with what you have described, if the voltage cutout was somehow disabled, then this could explain the problems.
Of the units that I have seen in the past like this, the red LED would describe the battery voltage being too low to safely power the unit (i.e. battery be dead). Generally a couple of minutes charge will bring it up to a safe working value. However, after 30 minutes this certainly should have been enough. On one of my motorola units, the battery has expanded a couple of millimeters as it starts to dissociate. It may be worth you checking to see whether the battery in your universal has distorted in any way.
Hmm the red light comes on mine all the time.
It just means the battery is low and the unit is charging. .
It should turn green when the battery is at or near optimum charge.
no....thats not the red, charging is orangy when i say red i mean PROPER red. battery is not distorted, and to the best of my knowledge the unit had a good charge, im pretty sure it must have been some kind of hardware short, and am going to call orange as soon as im back in the country.
dosent explain though why when i whacked it it started working again. the whack instantly made the light go out :wink:
i did a battery rundown test as soon as i got the unit, and posted the results on the forum, if the cut off was not working, i would have ended up with a red light then.
i dont have the manual with me now, but is there any documentation on the red light?
Found this site which had an online manual:
http://www.rich-michael.com/pdf/User Manuals/050802_Universal_Generic_Manual_English_CDL.pdf
What does the phone say in the Power Tab?
A really useful extract:
13 Notification LED Bi-color LED on the right side: Green and Orange
for GSM/WCDMA standby, SMS message, GSM/
WCDMA network status, notification, battery charging
status.
Bi-color LED on the left side: Blue andGreen for
Bluetooth system notification of powered-up and
ready to transmit radio frequency signal, and Wi-Fi
status.
Couldn't find anything else on the LEDs
Found this site which had an online manual:
http://www.rich-michael.com/pdf/User Manuals/050802_Universal_Generic_Manual_English_CDL.pdf
What does the phone say in the Power Tab?
A really useful extract:
13 Notification LED Bi-color LED on the right side: Green and Orange
for GSM/WCDMA standby, SMS message, GSM/
WCDMA network status, notification, battery charging
status.
Bi-color LED on the left side: Blue andGreen for
Bluetooth system notification of powered-up and
ready to transmit radio frequency signal, and Wi-Fi
status.
Couldn't find anything else on the LEDs
Sorry to drag up this old post.
My friend dropped my phone (Orange SPV C500) a few days ago on to a tiled floor. The phone didn't appear to be broken or faulty at all at the time. I even managed to use TomTom navigator to go to the airport, but for some reason when I looked at it before I went to sleep, the phone was off. I assumed the battery had gone (even though it should have lasted at least another day). I tried to plug in the mains charger, but the LED showed a red light. I left it plugged in while I slept, but it was the same in the morning. The phone won't power on at all. I've read that this normally happens on a flat battery, but I am pretty sure it still had juice for another day.
I brought a new battery, but to no avail, the phone still shows the red light when plugged into the mains. No light at all when plugged via USB to my computer. The phone won't power on at all.
It must have broke something when it was dropped. But I'm confused as to why it took a few hours to take any effect.
I also notice that even without the battery in the phone, the LED will still light up as red when plugged in to the mains.
I've tried whacking the phone now, but nothing. Anyone have any idea whether it can be fixed?
JOEJOETHEJOEY said:
Sorry to drag up this old post.
My friend dropped my phone (Orange SPV C500) a few days ago on to a tiled floor. The phone didn't appear to be broken or faulty at all at the time. I even managed to use TomTom navigator to go to the airport, but for some reason when I looked at it before I went to sleep, the phone was off. I assumed the battery had gone (even though it should have lasted at least another day). I tried to plug in the mains charger, but the LED showed a red light. I left it plugged in while I slept, but it was the same in the morning. The phone won't power on at all. I've read that this normally happens on a flat battery, but I am pretty sure it still had juice for another day.
I brought a new battery, but to no avail, the phone still shows the red light when plugged into the mains. No light at all when plugged via USB to my computer. The phone won't power on at all.
It must have broke something when it was dropped. But I'm confused as to why it took a few hours to take any effect.
I also notice that even without the battery in the phone, the LED will still light up as red when plugged in to the mains.
I've tried whacking the phone now, but nothing. Anyone have any idea whether it can be fixed?
Click to expand...
Click to collapse
this is damn scary! Every day more people add on to the "my univ's gone dead after a small drop" community :?
When my univ was brand new, a friend of mine dropped it from a coffee bar table 3 feet high, and i still heave a sigh! Cant believe nothing happened...!
But one thing i guess we all know, its a "drop" away to kiss our device good bye :roll:
hope you get it back up and running m8! look around the forums, there are lots of breakdown-solutions threads...
cheers,
San
nice work afhstingray
do you think it was a baterry problem.
i have often used my battery till tit just ran out, from what i read in the post it seems to be a bad practice. anyway to turn off the phone
i doubt it was a battery problem as i've been using it until now without problems. (i didnt get a replacement as soon as i got back cos im waiting for this unit to get a bit scruffy before i get it replaced)
i had this once on my c500 as well, but taking out the battery for an hour did the trick. so i dont think the problem is related.
i've dropped my universal quite a few times already and im happy to say other than a few annoying dings on the metal plate with the orange logo, its working fine. and 2 of the drops were pretty bad ones too, i thought for sure the screen would die or crack. guess i got lucky and it hit the floor at an angle not too critical
total stab in the dark but maybe a broken connection on charging circuit? that could be why phone was ok then battery died and its now unable to charge?
ViaraiX said:
total stab in the dark but maybe a broken connection on charging circuit? that could be why phone was ok then battery died and its now unable to charge?
Click to expand...
Click to collapse
wouldnt it have worked if it was plugged into the AC then?
Well my Exec was dropped onto concrete at the petrol station whilst I was trying to sort out TomTom and fill up my Yamaha R6 bike at the same time :roll:
No problems, just a couple of case marks.
I guess multitasking should be left to the ladies and computers :lol:
steverae said:
hehe, i'm an IT technician and it's the first thing i try, especially with Printers.....
They don't teach you that on MSCA courses.....
Click to expand...
Click to collapse
Also explains why Servers are built so solidly.
When you are trying to recover a server at 2am in the morning they need to stand up to all but a sledgehammer :twisted:
I got a used wizard today,it is a few weeks old I also got a cradle with it.
I pluged in the cradle to the USB port and the charger to power, after playing with it for 1-2 hours I placed the wizard on the cradle to charge and after a few mins i noticed that it was over heating. I removed it from the cradle right away and noticed that the battery was droping 1% every minute or so. After it was down to 27% i removed the charger and left only the usb connection and placed the wizard on the cradle again. it was charging fine, when it was up to 90% removed it from the cradle and again was droping fast.
When it was down to around 25-30% of the battery I did a soft reset and since then I can never get it to start again also the red charging light does not show.
What the heck is wrong with it? I also get a light burning smell from the bottom of the wizard where the connector is located.
Any help?
I need your lights guys.
Don't like the sound of the light burning smell, that sounds like an electrical fault. It looks like your battery has died and the wizard battery setup is well known to do this. You need to plug it into the official mains charger (not the usb one) as this has an output of 1A, enough to kick start the wizard battery into life and start the charging. You need to wait a short while though before the light comes on. If this fails try to get a new battery and try that. Any more light burning smells and it needs to go back to the supplier.
I would suggest that you send it back to replace/repair. The rapid dropping of the battery power suggest that it is using power somewhere (illegally). I've heard cases of battery caught on fire, etc. and I won't suggest you to use it anymore until you sort out the 'burning' smell.
First of all thanks for your replys.
I pluged the charger on it and the red charging light came on after a while.
charged for over 6 hours and its still red? I think after been charged should change to green? right?
anyways after all that still doesnt want to turn on. I got it to start a couple of times but only to the point that shows the splash screen with the rom numbers and then it turns back off.
Should I give it a smash across the room on the wall? done that with some other things and worked just kiding.
Forgot to add that up to the point when i did the soft reset the device was working fine except the charge drop. Soft reset was done while it was working ( turned on)..... if thats any help.
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
fonec said:
i thinking u need flash phone with jafwm
and here u will find 3 flashs
www.gsm-support.info
Click to expand...
Click to collapse
That ain't gonna do jack sh1t to it. If it can't start to get into bootloader, it can't flash....and it's not a flash issue.
Usually the red light means power but not charging - happens to my qtek 9100 when I let it get too flat and I have to remove and insert the battery while the mains adaptor is attached - others have to 'jump start' the battery by directly connecting to a PSU - I wouldn't do this with yours.
From what you have said it sounds like a short somewhere. Any signs of water damage? Warranty? What Wizard do you have and what country are you in?
Richard
I got the wiza 200 O2 xda mini S from a guy in UK from ebay. The idiot sold me a cradle for it with an adaptor that says 12V on it (Like an idiot that I am i just noticed that) but then again how am I supposed to think that he gave me an adaptor that its not made for it when it says on the back of it "for Imate - Kjam". Do you guys think thats what burned the **** out of the unit ?
dont forget that some times turns on shows the ROMS numbers and turns off.
No water damage... I think its on warranty... I live in Greece.
Might not be the cradle - it could be it steps down internally to 5v. Use a meter and check what it outputs to the phone. Warranty with XDA's are 2 years to the *original* purchaser. As they are only supplied with an airtime agreement then that isn't you.
Richard
have you tried changing batteries to a new one? Seriously, thats the easiest thing you could do right now and you could actually get results.
Ok this is what I did.
Removed the baterry from the device,
got a 12V 1 Amp power supply that I had lying around and give it a few shots connecting it to the battery giving it an electro shock.
(If you're going to try this be very carefull.<<<< DONT LEAVE the power supply connected to the battery>>>> just give it a few shots 1 second on and off.
That was it.
It started working, device turned on and now its charging (I think) yellow light is on.
I'm going to leave it on for a few hours and see what happens.
Wish me good luck. I'll let you know soon.
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
SmartMan said:
ok... this is what happend.
Battery is drained and its not charging due to a blown fust on the main board.
I open the phone and placed and solder a little wire over the fuse.
Still does not charge. ^%$#%$#$^%$*
Before I replaced the fuse or should i say short it the yellow light would come on for a few min and then red again. Now when I charge the battery with another external power supply the pda comes on for a few mins and then dies again. ( no charging light whatsoever).
Does anyone know where to get a mainboard for it and about how much it costs?
Asking for help again.
Click to expand...
Click to collapse
Hey man, sorry to hear about that.
The best you can do is to claim your money from ebay.
You probably killed it when you pluged in the 12V PSU. That's 230% of the normal Volts! Otherwise sell it for parts.
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
SmartMan said:
I'm in the process of claiming the money back from the IDIOT that sold it to me.
Lets see if that part of Ebay works as good.
Click to expand...
Click to collapse
Doubt it. Did you ask the seller for help before opening the phone and voiding the original warranty on the device?
SmartMan said:
ok... this is what happend.
I open the phone and placed and solder a little wire over the fuse.
Click to expand...
Click to collapse
Not a good idea IMO as now the blame is on you as previously he may have been able to get warranty service from the original vendor.
Richard
I did ask.
He is not the original buyer.
what was I suposed to do.... track back 2-3 buyers to find the original... send it to him so he can have it repaired? Anyway it was out of warranty because of the burned fuse that says that some other charger was used with it.
I had a similar thing happen but fortunately not as bad as yours. Twice now my battery has mysteriously drained completely. The last time when I tried to turn the unit on, it flashed the boot screen for a couple of seconds then poof, no more juice. When I plugged it into the USB port, nothing, no lights, no charge, no recognition from Activesync, I thought the unit was fried. I use Tmobile and got to admit they did send me a replacement fairly quickly. Before I packed up my unit I thought maybe I should plug it in using the wall charger and presto, it came on and is working fine. I have no idea what causes this but do know that if the battery is completely discharged the USB port can not over come this to put a charge on.
Same thing happened to me, kind of strange though. The charge was perhaps 70% to the best of my knowledge. I flashed it with Mr. Clean ROM and booted it up.. it came in fine into WM5, then it started the installation of the 3 progs or whatever comes with Mr. Clean.. after the second finished the unit just died *poff*. Screen blank, no responce to power buttons or any other buttons for that matter.
I've tried taking out the battery for different intervals of time, no luck. I've tried using the AC charger, no luck. No lights, sounds, telepathy or matrix ****.. it just lies there like a dummy phone.. hmm what to do. Bought it from a guy in UK (im in sweden) on eBay, don't think I will have much luck there.. even though it's brand new...
Any thouhgts?
I have had this problem - I bought a replacement battery and all is now fine. Another thread in this group states that the battery cannot charge without the OS up - so if the battery is completely discharged then it is impossible to charge through the phone. The only solution seems to be somehow to charge the battery directly - as appears to have been done earlier in this thread.
Chris
p.s. if anyone knows of another way to do it I'd be interested to hear as I'd like to revive my old battery and keep it as a spare
I think I may have a faulty battery (hoping it's not a problem with the phone itself). The battery seems to hold it's charge ok but when it has completely run out of charge or is close to running out, I have a lot of problems getting it to charge up.
If the phone is turned off, the orange light comes on but then goes off again after about 10 minutes and the battery still shows 0% when I turn the phone on to check progress. I have to remove the cable, then remove the battery for at least 5 mins, turn the phone on and while it is booting up, do a soft reset. I then insert the cable as the phone is booting up and after a while the orange light comes on and the phone starts to charge. It takes ages to charge and when it has got to about 20%, I then turn off the phone and it then charges the remaining % fairly quickly. It only gets to 99% though....
I am pretty sure (like 99.9%) that it is just the battery as my son has the same phone. We have swapped chargers - no difference. We then swapped batteries - my phone worked fine and his wouldn't charge! However, when I went in the Orange shop they were insistant that I had to send the phone back as well, which I really don't want to do as I haven't got a spare phone (even a brick).
Unfortunately, as I have just lost my job, I don't want to have to buy a new battery as they are about £25 but I guess I will have to.
What do people think - is it just a faulty battery? Has anyone else had this issue with their phone - i.e is it a known problem?? Hope someone can help...
I guess no-one bothers to answers questions from newbies then....
idd, i feel the same way..
but i think your battery is dead, don't have much experience about that subject but when you exchange the battery with someelse and then his phone acts weird to, look no further.
Hi guys!
I know, that there are some threads about the topic, but i think, here it is a bit different...i´ll describe:
Everything was OK with my withe G1, since I forgot to recharge the battery, and the G1 switched off. I wanted to recharge it, but - you know- the red led light blinked...i read different threads etc, and then I decided, to buy a new battery. The new battery arrived yesterday, and I put it in my G1, tried to switch it on, and it worked. I was quite happy! I taped it on the charging unit, and the first problem: the battery display didnt moved, it remained at 23%, also after a few hours at the charging unit. I knew the problem, because it was the same with my old battery, but it doesnt interest me, because the battery recharged, only the battery indicator showed that not. I thought OK, dont thinked about it, and waited. Today: I took my G1, yes, battery display at 23%, no problem. I switched it off and after a few hours I wanted to switch it on. Second problem - F**K! The red led light blinked...and now, the battery doesnt recharge at all. The G1 works now only, if the charging unit is put on it, if I remove it, the G1 switchs off. Its the same behavior with the old battery.
I dont know what to do now, because i dont think, that it is a hardwarebug, because yesterday it worked, with the brandnew battery. Or is it possible, that the G1 destroys my batterys while switching it off?
I hope, that there are solutions for this...because im loosing my temper slowly...
Can you charge the battery if the phone is off? Red led light should show. You should wait even 30-60 minutes for this - it depends of battery discharge. If the red light will not show this will means that your hardware is broken (phone or phone charger). You can try use another phone charger to test.
That works sometimes....at the moment not, but one hour before, yes.
I had the G1 with the USB cable on the PC, the phone was off, the light was red (not blinking). I waited about 50minutes, then disconnected, tried to switch it on - nothing except a red led light - blinking
At the moment, there isnt any led light, if i connect the phone to the charger unit or the PC...
It looks like hardware problem :/
Would be OK, because there is still warranty.
But what irritates me, is, that it worked without problems, when the battery was charged. Also with the new battery...worked good, since I switched the phone off.
I only want to be sure, because the return merchandise authorization (rma) takes quite long time...
I have the same problem. last week i bought the phone, and used it till the phone battery was empty. I tried to recharge the phone, but i wouldn't go on, only the red light blinking. I had the phone charged for 2 days, with the og charger, no result. Looked like the phone was dead.
Today i tried it again, still no result. All of a sudden the phone turned on and was charging. It is now on 99%.
Should i contact HTC?
edit:
sorry, wrong forum
Just a wild guess. It could also be the ROM that you have. I had a similar problem with my battery drained out like that with flashing red light. Come to find out later that it was something to do with the ROM (CM6.x) that I was using.
I bought a second hand HD2, however it arrived with a third-party chinese battery. I contacted the seller who apologised and said that battery was a replacement because the original didn't hold a good charge, and he would send the original through the post. The battery however was fully charged so I flashed all the neccessary files and installed NAND Android (my reason for buying it in the first place), however today - the same day it arrived - I noticed that the orange charge light was going off, usually when the phone screen went off. This necessitated plugging the USB lead back in again, and within sometimes less than a minute the same problem would occur. I have checked the battery prongs, reset the the phone, changed USB settings etc and the problem persists.
Just wondered of I should be worried...I am unable to find an identical problem to this on the forums so I'm assuming it's not a ROM issue. I am currently using the Desire port from DFT.
Would a cheap Chinese battery demonstrate this sort of problem?
The seller says he never had an issue of charging the phone.
My next resort is to flash Windows Mobile back on, but I'm at work and a bit anxious so was hoping for someone with some experience to reassure me!
All USB syncing etc works fine...it is literally just charging that's the issue.
Maybe it's your USB that's faulty. I had a faulty usb that would go on and off sometimes too. However I don't see why the battery would affect the LED light, as the battery has to be connected to the phone for it to stay on, and so the battery can't be losing it's connection with the phone randomly, so it's either your usb cord, or the port.
Word of advice, don't let your phone lose power cuz of the faulty charging. I assume you know that MAGLDR doesn't let you charge the phone while off, so a dead battery in our case, is a dead phone. Happened to me once cuz of my usb, luckily there was still a small amount of charge left after i took the battery out and placed it back in.
It's definitely not the cable as I've used an official HTC charger with it which does exactly the same thing. I've also tried with a Samsung MicroUSB charger from my Galaxy S
Maybe it's the usb port then... That's the worst case scenario because you'd have to get the whole motherboard replaced...
However if in winmo you don't experience the problems, then it was just some software problems, so try a different radio and build, and see if they work.
Edit:
Or maybe it's the LED that's faulty. (never heard of such a situation but anything is possible) >.>
Does it still charge even if the LED is not orange/on?
Thing is though I can pretty much get it to stay charging if I don't let it lock and the screen go off? Could this still be a problem with the USB port? I'm getting worried now as I don't like the hassle of sending things back through eBay. I'm wondering if the seller bought a spare battery thinking it was just a battery problem and isn't telling the whole story. Foolishly I didn't test the device with Windows Mobile, I just went straight into flashing as I had put Android on my friend's HD2 the other day in exactly the same way...his is even an ex Virgin Mobile phone like this one. Needless to say, he is having no charging issues.
Dude dont worry , the problem is the battery ! i got two chinese battery ones and both cant charge with the phone, i have to use eksternal charger Dont worry the red and orange led flashes constantly when i try to charge it
Just buy a cheap charger from ebay , and buy a oem htc hd2 battery
Hi thanks for your reply. Mine doesn't flash red and orange though: the orange light comes on as normal and the phone reports it as charging, but after a while (seems to be when the phone goes to standby most of the time) the orange light turns off and the charging symbol disappears. If I unplug and replug again the light comes back on for a period. I've not tested thoroughly but I THINK it will stay charging when I leave the phone out of standby with the screen set to stay on for 30 minutes. I really HOPE it's a battery issue but it sounds slightly different to yours as mine does at least charge to a degree. I'm worried there's a blown capacitor somewhere on the logic board that's making the phone charge malfunction but obviously there's no way of testing until I get a new battery.
It concerns me that the seller said he had no charging problems...he must have been able to charge it somehow as the battery was full when it arrived...could I have burnt something out when flashing?!
Mine do charge to about 50 % and then it stops
Im 100 % sure its the battery becouse the battery has a circuitboard inside of it, and thats often messed up considering its made cheap in china . But test it with your friends hd2 original battery You can 2 see if the wet indicatior has been activated
the " white " paper next to the battery poles should be white and not pink, alltso where the skrewholes of the phone that should allso be white just to make sure your phone is not waterdamaget
I don't think flashing could have burnt something out. Overclocking and generating a lot of heat can burn something out though.
Didn't you receive the stock battery? Why not try it with that, and if the problem stilll persists then it might not be the battery. Either way, it will help you to test out the phone with a stock battery.
I tried it again after a few hours and it charged for a fair while before the light went off again.
I don't have the original battery as the seller has yet to mail it to me.
Does anyone else think it's worth me trying out a stock Windows Mobile ROM to see if it works? Might be that Android ROMs are less forgiving of cheap batteries with dodgy circuitry..
UPDATE
Ok so I've flashed Windows Mobile onto the device and wiped Magldr. The phone now alternates between a green and an amber light on the charging indicator. Looks like Windows Mobile won't charge it at all!
Does anyone know what this means?
I've checked for water damage in the areas mentioned and there is no sign.
Well your best bet is to send it in for repairs. But I'd suggest you test the phone out first with a stock battery.
Well I Only bought the phone yesterday so I certainly won't be paying for any repairs.
Got a replacement battery today - a genuine HTC one.
Plugged in, switched on....flashing between amber and green
I have a nagging suspicion this is going to be an eBay refund nightmare.
have you checked that the pins on the phone is not bendt? pins where battery poles connect to phone
problem solved? fingers crossed
OK so as a last resort I flashed radio 2.15 to the device. Seems that this has completely fixed the problem as without even restoring the phone is now charging properly. It seems that a corrupted radio flash had affected the charge somehow....at least I hope so.
The same problem has not come back again today at all.
Might be worth throwing this solution in a problems and solutions section as I haven't found any reference to it on the net and it might fix things for others panicking over their handsets.
That's nice.
Good for you, since it's a hassle to deal with sending back the device and shizz like that.
was just searching is anyone had a similar problem like me. to the OP yours sounds like my problem.
Had these fake OEM batteries for a while now. Until recently they have been charging ang turning off in 1 1/2 minutes. put a genuine OEM battery in and the problem is gone.
My solution was OEM can charge thru phone but fakes cant, use fakes as backup and charge it thru a desktop charger. goodluck