Hi
My XDAII doesn't start as it just hangs at first boot screen and nothing happens there after. Sometimes charging takes place and sometimes, it doesn't charge while plugged with a wall charger.
Any suggestions for this problem?
ya, I can put this ini bootloader mode and I have tried a no. of diff. ROMS (WM SE 2003 and WM5 as well).
Help
yes this is exactly whats happening to me I have a lovely functional XDA 11 which works like a charm THEN I bought a second on EBAY (Stop laughing !!) which sometimes boots sometimes doesnt - sometimes it even starts and goes all the way and functions for up to a few mins then freezes and has to reboot and is then dead as a mullet!! I take the battery out and wait a while and she starts sometimes again sometimes take a few attempts - Help any theories?
I have exactly the same problem with the blank white screen after the o2 splash.
But in addition, I get screen flicker and fuzziness on the occassion that I DO get it to work (after leaving the battery out all night).
same problem i am with u
Hello brothers. I have same problem my o2 xda IIs please give me a solution
First time i have hangup problem then i tried upgrade 2k5 upgrade successful.Then i have same problem is it softwere problem or hardware please tell me
It seems like this bacame a problem for a lot of people - something similar started hapening to me, too ... At first it was scarce, but now it is impossible to use it as a phone - it hangs to many times... I suppose it's a hardware problem ...
need some help
Hey guys my O2 XDA 2i is not starting. It shows the welcome screen and the screen alignment . and you keep aligning the screen for ages to see nothing happning. anybody has a solution.
I also have a Imate pocket PC, but it works better than O2 XDA 2i. no problem from last 3 years
Thanks for all your post, I have the same problem and now it has been sorted!
my xda also don't starts windows and it all started when i run doc partition tool on wm6.so i managed to install wm2003 and it works fine try downgrading to wm2003 and you will see the difference that your device will never give you that problem again
Have u had a think?
Du think there might be a virus?
All i can recommend is to upgrade the rom
hi, sorry for ma english, Now huge thanks to all who continue to help me here. i have the htc p3300, no branding. i want to flash my htc. have already done so few times no problems. but this time i think i have a problem with a bootloader. it was not even to flash. A reset, and now it no longer work. At the beginning it was still remained black. I still hear the "blink" or "dong" or whatever I should call it when I connect it with my pc. But no visible connection. Have Vista. Now, I have it in the socket, but will not see the light lit. . Have tried various roms up again to draw even original of o2 or t-mobile but always from the break because no connection recognize ... to really please help
Maybe its only the backlight that is not working.
rhino666 said:
Maybe its only the backlight that is not working.
Click to expand...
Click to collapse
hmm... i think that isn´t the reason because it give not a reaction when i connect it with my pc. and no reaction when i chage it, no light. u understand??
guys can somebody help me with my dopod 838pro when ever i use the keyboard the fone always shutsdown dont know why i just upgrade it to wm6!!!! what should i do!!!!! please need help badly!!!
p.s. and my herms sometimes crashes with out prior notice mmmmmmm
jromep07 said:
p.s. and my herms sometimes crashes with out prior notice mmmmmmm
Click to expand...
Click to collapse
When you say it shuts down, do you mean it goes completely off and when you start it again it goes through the boot up process?
.. and when it crashes do you mean it freezes, or the screen goes blank or it turns off?
Did this happen immediately following the upgrade? I'm trying to decide whether this is physical or software related.
Mike
mike
thanks for the reply! yes it goes completely off and when you start it again it goes through the boot up process! and about the crushes yes it turns my fone off it doesn't freezes it just turn off!!!! if its a program related what should i do or if its a hardware what should i do!!!! i never notice this problem before! tnx!!!
jromep07 said:
mike
thanks for the reply! yes it goes completely off and when you start it again it goes through the boot up process! and about the crushes yes it turns my fone off it doesn't freezes it just turn off!!!! if its a program related what should i do or if its a hardware what should i do!!!! i never notice this problem before! tnx!!!
Click to expand...
Click to collapse
Have a look here. I think it may be this. Opening the keyboard may be causing enough movement to momentarily disconnect the battery. At other times it will just be random. If it stays on when left to sit without any movement then this is likely to be your problem:
http://forum.xda-developers.com/showpost.php?p=2451075&postcount=4
Mike
mike
tnx ill gonna give it a try! hope it works! ill inform you if its successful! tnx again!
and can i ask another question? can i use the at&t3.62.502.3 wm6 rom on my dopod coz its newer than the dopod update! tnx
mike
tnxs alot i think it works i have using my keyboard for about 40mins and it doesn't shutoff any more!!! tnx a million!
right peeps this is the issue i am having and i am not sure if this is the right place to post this problem, i have had a blackstone for a while and all working fine upgraded to duttys holy grail 5/11/09 release and all was fine, i bought another blackstone as a none worker and it turned out to be the battery? i replace the battery and all fired up wm6.1 and worked for ages, i decided to put duttys holy garil on the latest blackstone and this is where the problem is.
when the phone flashes and reboots the screen looks like its in the wrong resolution? all the colours are distorted but if i press the power button once and then back on again the screen comes back normal? but after about 5 min the phone seems really warm and then locks up?
could this be a rom issue or radio issue
my older blackstone radio is different to what is in this one? any ideas where to begin, regards
just to add, when the phone first boots the screen saying "smart mobility" is white how it should do but it then turns like a light blue and thats when the screen goes funny as if it is in the wrong resolution, cheers
just found out that with a sim card in the phone there is no phone functions, i can not turn flight mode of or can i turn the phone function on, regards
someone must have come across this befor??
Hi
is it possible for you to upgrade your HardSPL to 1.56?
Screen colors distorsion are often linked to improper HARDSPL version usage.
Regards
hi frha
yepp that done the job thanks,
i upgraded to 1.4 before i flashed a new rom so after your advice i rechecked the version and it said v1.07?? not sure what happened there, i upgraded to 1.56 and rechecked and all seems well, the phone booted and started setup for the network provider and all seems stable altho the radio version is different to my other one? this one is ver 1.13.25.24 and the other is 1.14.25.24, would adding the updated radio be a benifit, many thanks for you help in solving my hair pulling saga, regards dave
you're welcome
enjoy your HTC HD.
Regards
Solution found, thread closed
p.s. this is a common problem and has been answered many times before
Cero92 said:
Hi all, i just got a Qtek 9090 with WM2003 (ITA). I upgraded to WM6.1, but now it has some strange problems: first of all, when it goes in standby, sometimes it doesn't wake up. If i have to reset it, most of times it doesn't boot (it shut down before WM loads) or i get R: None G: None and i have to reset again (otherwise the phone won't work).
The lock at the boot doesn't happen when the phone is connected at the USB port (i think that's because it charges, maybe it's a battery problem?)
Another thing is that i can't turn it off: if i hold pressed the power button, it deactivate the backlught but the device stays on, and if i make another long press, i get the backlight back again... I had this problem also with WM2003, maybe it's normal?
What do you think? Whan can i do?
Click to expand...
Click to collapse
Have you make a HardReset?
The correct HardReset, not only reset and press Power button!!!
See in my HowTo Section...
and why not WM6.5.5 see here
yep, hard reset is a good start, but about your other problems:
the device does not really turn off, like other phones. pressing the power button makes it go to hibernate, the display turns off, depending on your settings, it locks the hardware buttons and it shuts off wi-fi, it hardly uses any energy but gsm/gprs stay on.
the device seems to be off, yet the phone is one and you can be called. that is the closest you get to switching it off. when you turn on airplane mode, the battery consumption is even less so there is not really a need to turn it off.
pressing and holding the power button always was for the backlight. many other devices open up a shutdown menu when you do that, that would allow you to turn it off, soft reset, or switch off the backlight, but for the BA, that is not the standard. however, if i read it right, d-two is working on remapping the power button, probably for that cause.
the R: none G: none issue is known and not a problem with your phone, whenever you run out of power or remove the battery for a second, the next boot will be w/o radio (R and most roms don't allow booting without it. that's why you get stuck there and have to perform a soft reset. back in the days of wm2003 i used to remove the battery when the device froze to reset it w/o the stylus, because it didn't matter then. with cooked roms, it is different, just like the booting splash screen or the way to perform a hard reset, many things change on a cooked rom.
the issue with waking up from standby, or the SOD (standby of death) is an issue, that most likely has something to do with a backup, restored after flashing another os, or maybe you didn't perform a hard reset, as stated by d-two. you should do that, now that the device is still new, you have nothing to lose
also, read through the tutorials posted by d-two and myself, whether you missed anything while flashing.
The "real" hard reset is the one i can get by pressing camera + record button and reset? If so, i already did it after flash (i use d-two 6.1 Manila ROM in WWE)
It shows me 3 options, i put on YES "Clean Registry Hive" and "Format Storage" then i press the mail button, the screen become white for a while and the next boot al seems to be ok.
It seems, because after some time i get again the "standby of death" and, if i press the reset button, the most of time it won't boot up again (it turns off before i can get to WM), if it works phone doesn't. All these boot problem can be avoided by connecting the phone to the usb cradle, so maybe it's also a battery problem, i think...
@ d-two: i'll try your new ROM, however before i've tried your 6.1 ROM
I've already read your guide because i've got Windows 7 and i couldn't flash without your tutorial
NEWS: installed d-two new ROM, after flash i made the hard reset selecting the second and the third options, then i get the blank screen and, when viewing the htc screen, it shut down itself like it did before
As always, with the usb connected, it has no problem :\
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
n0rbi666 said:
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
Click to expand...
Click to collapse
That's what i was thinking (and that's i hope it isn't)... Now with another recharge cycle it seems to be good also with cooked ROMs, i hope it's solved
Maybe you just have to charge/discharge it for 4-5 times, and it will restore it's capacity. Mine BA was turning off when battery indicator was showing ~60-70%, and now I'm waiting for new battery (i destroyed original )
"charge/discharge it for 4-5 times" does not have an effect on Li-ion kind of batteries. This is probably a software problem. When you turn your phone on (after removing a battery) it always shows "None" for R and G, so just press Reset button and it will be ok. I use Reset to power it on Then you can flash 6.5.5 which doesn't have problems, and do a hard reset. There should be no problem at all..
I also got the problem with the stock ROM :\
The R: None G: None error is the less important problem
Got any luck fixing it? I've had similar problems before, sometimes it turned itself off when the battery was at 60% in WM2003. Did you update to d-two's 6.5.5?
Yes, now i'm running d-two's 6.5.5 ROM.
No, i still had the problem Yesterday i called to the assistance service and they said me to remove the battery and after a while recharge it.
I put off the battery yesterday at 16 and i put it again in the phone this morning at 8, i charged it but i still have the problem
This evening i called again and they said me that i have to send it back, i'll flash the original ROM and send it on monday.
That's a shame, i really like this device, even if it's not mine, my sister uses it and she's not a pro user, what a waste
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
marko_serb said:
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
Click to expand...
Click to collapse
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Cero92 said:
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Click to expand...
Click to collapse
My Roms have no SOD
This is when vbase32 have all 01000000 base adress !!!
Search about SOD!!
No, this happens only with my old battery. I'll try it out now with this new ROM!
I was trying to understand his problem
Just to know, what kitchen do you use?
Cero92 said:
I was trying to understand his problem
Just to know, what kitchen do you use?
Click to expand...
Click to collapse
First i have create my own kitchen but then i have found the OSBuilder and this is the best kitchen ever
With this kitchen you can look the Vbase32 for SOD!!!
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Cero92 said:
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Click to expand...
Click to collapse
I think so, sorry
d-two said:
I think so, sorry
Click to expand...
Click to collapse
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Cero92 said:
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Click to expand...
Click to collapse
good luck But very cool that you have warranty