USB Cable Disconnected During ROM Install. Did I Brick It? - Touch CDMA General

I was attempting to unlock the GPS on my XV6900 after installing the official Verizon WM 6.1 update, following the instructions on the PPC Haven wiki here: http://wiki.ppchaven.com/index.php?title=Pocket_PC_WIki:FIX_VERIZON_GPS.
I got through the unlocking with 0.40 coke and was flashing 'Flash Sprint ROM RUU_Vogue_SPRINT_WWE_1.12.651.1_2.13.00_SPC_NV133_Ship'.
At 13% completete the usb cable was disconnected. I'm now stuck on the rainbow screen with the following info displayed:
VOGU100
SPL-0.36.0000
CPLD-3
'RUUNBH' is displayed in the upper right hand corner.
I tried to reflash the sprint ROM and unlocking with 0.40 coke again without any success. My laptop does not recognize the device when connected via usb, so active sync is also not working.
So this is my last hope. Is there anyone out there who can help out a noob, or did I damage my phone beyond repair?
Thanks in advance for your help. I did a search before posting, but didn't come across the answer. Sorry if I missed it

Anyone? Is it bricked?

you could try this out, if you have a microSD (non HD, wich mean, 2go or less)
1. Download NSFAN's latest Sprint WM6.1 Rom and extract to desktop
2. Rename ROMFILE.nbh to voguimg.nbh
3. Copy voguimg.nbh to MicroSD card that has been formatted to FAT32
4. Insert MicroSD card in phone, and enter bootloader via holding down the Power/Camera/Reset buttons all together.
5. Flash ROM
6. Hard Reset Phone
Good luck!

try the sprint rom with the RUU, even tho it says you need an active sync connection as long as the phone says USB at the bottom of the bootloader screen you can start the update

same happened to me when updating the official verizon 6.1, i took the battery out for like 20 mins and then retried and worked.

Related

Help Please error during rom update

Hi, I have a TMobile MDA with IPL 2.26 and SPL 2.26 and I was trying to put a new rom but the program gave me an update error when reached 99% an now it is stuck in the boot screen (shows in the bottom USB connection) but when re-running the program it does not connect and activesync does not detect the phone. Before the rom update program ruu gave me the that said the phone required a newer program version.
Did I screwed the phone or there is a solution?
Thank you in advance for your help and best regards
Issue Was solved downloading from T-MOBILE the updated ROM and executing the program
Nick
Nope, you're good.
As long as you can enter bootloader and it reads usb in the bottom corner, your wizard can be saved. Don't worry about active sync, it won't read. Get a stock rom from your provider...if Tmo, it is available on their website. Plug in the usb and get into the tri-color boot. Run the stock ruu. Do not let anything interfere with the process, so disable your screensaver, don't let cats or kids near the usb cord, etc (trust me on that one!). NBow flash the stock rom. It will take 10 minutes roughly, be patient, DO NOT unplug usb for any reason...let it flash and reboot. Once flashed, make sure you are cid/sim unlocked...use lokiwiz (read the sticky on unlocking). You cannot change roms from stock to custom without first unlocking. If you are already unlocked, once you have the stock rom re-installed, you can flash to a custom rom. The linky in my siggy explains in detail about reviving a "bricked" wizard.

Newbie: cannot install Hard SPL for love nor money help!!!

Before anyone ask's I have read all the posts regarding installing the Hard SPL but still have the same problem.
When I connect through Vista 32 via WMDC it recognizes my device fine, I then follow the steps in the tutorials but as soon as I press the button to update the ROM image it goes into the 3 colour screen and then into the updating ROM progress bar were it sits at 0% for ever.
My WMDC has disconnected at this stage and then I get a screen saying communication error which is obvious as WMDC has disconnected.
Is this a WMDC issue/ Vista or am I missing something
I then have to soft reset and it just re boots into my standard ROM.
Any advice woiuld be greatly appreciated
hello
1) connect your polaris to PC
2) run update utility
3) when you see 3 color screen unplug USB and replug it immediately
4) your SPL flash may start
5) when flash end correctely your polaris reboot
6) Flash any ROM you want
Thanks for the quick reply.
Tried doing exactly as you have stated.
Unplug and reconnect in the 3 colour bar screen, after which it goes into the updating screen and sits at 0% for ages until communication error comes up.
My WMDC has disconnected and does not reconnect.
I'm at my wits end!!
Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
I think hard-spl can not be installed with sdcard method!
Why not ??? With Trinity you can do it.
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
batista70 said:
Why not ??? With Trinity you can do it.
Click to expand...
Click to collapse
But this is not Trinity...Try it...
I know You can flash polaris if you use jumpspl (this is used by hard-spl flash) or hard-spl (this is used by os and radio flash).
But if you have original spl on you pda, and you want to flash with sd card, you will not use nor jumpspl neither hard-spl.
mikee5402 said:
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
Click to expand...
Click to collapse
hi there.
try to hard spl with your sd card not in the device.
go in to bootloader mode (BL mode - by pressing down the Camera button, then using the stylus, press and hold the RESET button at the bottom of the phone and release when tricolor screen appears),
now connect the device to your pc (it should show usb in the white part)
flash what you may... hard spl first, oli's recomended by me.
ItayE,
Did you try the hard-spl flash with sd method? Does it work?
I didn't read it was Vista compliant so I ran it from a windows XP SP2 machine with Active Sync 4.5.
I did mine by taking out the SIM card and the SD Card then resettting and running the HardSPL.
HTH
Leon
Cheers for the advice guys I have managed to do it.
I used the Hard-SPL-V2 first which worked fine then I flashed to one of A.Serg roms, very nice and quick it is too.
However my reception bars are down to 2 from 4 that I previously had, although the reception seems ok.
Sim: O2 UK
Rom: 1.52.ASerg.4 WWE
The radio version I have is: 1.58.25.14
Now this is were I am confused.
Can I flash the radio Rom without affecting the o/s Rom, I have downloaded a couple of radio rom versions but not sure if you do it the same way as I am scared of over writing something.
Also could anybody advise if they are in UK on O2 which version gives best reception.
Any further advice much appreciated.

help me - Frozen operator screen, unlocking, flashing and usb connector.

Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.
Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370
whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.
beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader
It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.
here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.
Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.
crap, my phone just ****ed off again. Same deal as before. Hate being broke.
help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you
what is your bootloader version
htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3
are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.
tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41
You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.
Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe
yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17
Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.

how to install updated rom without active sync

i have a tmobile wing and i have vista so i wanted to update my phone with a knew rom version....so i installed windows mobile device center 6.1 ...but it would not sync ,i uninsalled it then reinstalled it no go....so im wondering how can i hard spl my phone without my pc ....and install a rom ...now i tried my wifes touch pro 2 on the windows mobile device center and it works but my wing wont ....anyone ran into this problem or has a solution ...i read a few threads saying hard reset but that did not work
Do you intend to flash with the flash center using the USB cable or have you considered using an SD card to flash your ROM?
If you are using USB to flash have you tried putting your phone into bootloader mode? While pressing the camera button, press the soft reset button below the volume control with the stylus and continue to hold the camera button until the tri colored screen pops up. When it does, look in the bottom left ( if I recall correctly ) to see if it recognizes the USB connection. It will say USB in that bottom left spot if it is connected and you are ready to flash. Ideally you want to be connected via Active sync but it is possible to flash from the bootloader screen.
Consider flashing via SD card. There are many different threads on this and it really is a very simple process. I hear it is also better for flashing because if you unplug the USB cable during a flash you can brick your phone. Just an idea.
Good luck.
yes i would like to flash from wmdc if possible....ill try the bootloader mode first
i just tried it the bars come up and it says usb in the corner ...but wmdc would not recognise it ...is there some settings on the wing i need to do to get it to sync
1milenia said:
i just tried it the bars come up and it says usb in the corner ...but wmdc would not recognise it ...is there some settings on the wing i need to do to get it to sync
Click to expand...
Click to collapse
To flash from the boot loader screen you just need to go through the steps in the flash center. I never looked to see if my computer recognized the phone while plugged in; I just assumed it did not because active sync was not running. You should be able to initiate the flash through flash center and as you go through the steps it should recognize which rom you have loaded and it should read the rom you plan to install (which should be placed in the RUU folder within the flash center). I personally had to do this process about two flashes ago and can verify that it worked for me without having to "be connected" as far as Window's was concerned.
My advice, just go through the steps in flash center and you should see some progress. Good luck.
i went through the process it tells me nothing is connected then i have to exit
1milenia said:
i went through the process it tells me nothing is connected then i have to exit
Click to expand...
Click to collapse
I would then go through the steps to format a 2gb or less MicroSD card and place the ROM file in the root directory and renaming it HERAIMG. From what I hear, this is a safer way to flash anyway so this should be your method whenever possible. There are many threads describing this process. The hardest part for me was to find a way to properly format my card in my computer. My best advice if you have a Dell or another laptop with an SD slot built it, would be to use another port to plug into. I tried for days to find a way or a program to format my MicroSD card in the built in SD slot but no matter what I did, it would not work. Finally, after much frustration, I tried a usb card reader and managed to successfully format the MicroSD on the first try and have been flashing with this method ever since. Hopefully this is all it takes to get you back up and running again. Good luck once again; I'll have my fingers crossed.
HELLO
Please my phone htc p4350 just going to boot loader and not read an activ sync please iwant soulation

USPL via memory card method?

Guys, I have a P3300 that has a non-functioning USB connector. Charging works fine, but it will not sync over USB at all. The device is not detected at all. Even in the bootloader screen, when the USB cable is plugged in, it DOES NOT say "USB" in the bottom corner. Basically, the data functionality of the USB port is fried.
I had used USPL to flash a cooked ROM onto the device, and when the USB port worked, it all went fine. Now, with the USB port not working, I can only flash a stock ROM onto the phone using the memory card method. If I try to flash anything other than the stock ROM, it says "certificate invalid" and won't do it.
I read somewhere that there might be a method of doing the CID unlock by using the memory card, since the phone will not communicate with the computer via USB to use USPL the normal way. Can someone instruct me on how to do that? I have the USPL files on my computer, and simply renaming the .nbh file in order to try to use the memory card method won't work.
Can someone help me figure out how to use USPL or otherwise CID unlock the phone over some method other than USB to the computer? Thanks,
Well you can use activesync over BT, right? That might just do teh trick + SD card flash after it reboots to bootloader.
I might be wrong, it's just a thought
I tried that, but the USPL loader kills Activesync right at the start. So once the phone soft-reboots into the white screen and AS is killed, there is no more BT connection. So the USPL loader fails with an error of not being able to connect.
Can anyone else help?
I faced the same problem. White screen. I removed SIM and SDCARD. So I can flash normally.
Wiki: Artemis SD Card Flashing
Try reading the Wiki on Artemis SD Card Flashing
Those having questions on flashing (i.e. updating) their HTC Artemis could try following these steps 1) Backup e.g. PIM Backup 2) disable standby and hibernation then remove SIM & SDHC cards 3) if necessary then cid unlock 4) recommend hard reset or update to the latest official build 5) if necessary Update SPL to latest 1.11.cmon 6) flash new rom then hard reset 7) put in SIM & SDHC cards and enjoy the result of the hard work by the developer
Also check out this thread Uspl/rom upgrade/tips&tricks
Cheers
Tom
hello. I exactly have the same problem like the thread poster. my mini usb only charges and cant connect data to any pc. its probably broken as common with using the O2 artemis on a car phone charger and starting the car while the phone is still sitted and charging.
MY QUESTION: does "Artemis SD Card Flashing" doesnt require the USPL? since its CID locked?

Categories

Resources