ok ive managed to brick my phone...
ive made a goldcard and im pretty sure that everything is correct.
if i have only the goldcard file and heraimg.nbh on my card and insert it it says "checking sd" but then goes to the normal tricolor screen.
so i went and but heradiag.nbh on the card aswell.
it then starts checking but then comes up with the error:
sercurity level not cleared!
can someone help me?!
my ipl and spl is: 1.09.001
all help will be really apreciated!
thanks a lot
pseudo
same problem with me
Same!
Same here!!!
i made a goldcard, using a tutorial i found on here, and i'm positive i did it correct.
But still have a security warning!
Can can't get any further with my device.
I have IPL 4.23.0001
SPL 4.23.0000
I Can boot in OS, but then the OS hangs and can't press any buttons.
the only button i can press is the power off, and they i can choose YES/NO
And that works fine.
But the rest is just FROZEN!!
WHO CAN HELP ME PLEASE??
But it doens't sync in windows, so i can't do a FLASH, No flash can't be done from SD CARD?
THE GOLDCARD has no effect?
So who can help me out?
same prob - no solution until now...
nevermind didnt check the dates, old thread...
but still problems!
Any solution for this problem???????????????????
Related
Good people,
I thought I was stuborn and smart enough to follow your instructions to upgrade my old Tytn to WM6.1, but I think i lack the basic understanding. The only thing I am sure I have managed to do is to app-unlock the device. I also half-succeeded in installing a bootloader (SPL1.04). It shows a wonderful screen of four colors every now and then. But every attempt to go fro there to install WM6.1 or anything else (currently trying to install from SD), it goes through that screen and that is where it stops. Can you help me with the basics, what am I missing?
If the SPL on the tri-colour screen (bootloader) says 2.10 olipro you've done the best thing, if not then your in for some major hair pulling and a lot of reading...
Assuming you've got SPL 2.10 olipro & a charged battery......
1). Format an sd card fat32. Copy the .nbh file of the os you want and rename to "hermimg.nbh". Put back in phone.
2). Reset to bootloader - hold power, ok button above flywheel and reset with stylus. If you have formatted fat32 (NOT FAT) & the nbh file has been renamed properly, it should detect the flash file.
3). Follow instructions on screen....
This will fix your problem.
Cheers....
Hi All,
I have tried searching for the answer to this question and cannot find it, though I am sure I wont be the first to have had this problem.
I am trying to flash a new rom on my touch HD, have tried two different ones - duttys and black pearl. I have managed to get the upsl to work in the bootloader but i cannot get a rom to boot from the SD card. I have followed the instructions on the pages with the roms (same in each) and all i see is a screen flash up after running uspl saying "no image file" then it goes back to the bootloader screen.
In order to get out of bootloader I have to remove my battery which i assume is normal and then it goes back to the normal spl.
I am pulling my hair out on this one - and I dont have much to pull on!
I didnt think it would be so hard with all of the instructions about!
What want you do?
What stage has you done?
I wanted to load duttys rom using upsl but unfortunately I couldnt get it to work so I used the program that comes with the rom to load it in without using bootloader.
I had to load on Olinex to make it work
I had a similar thing the other day when I was having a blonde moment. Renamed the image file BLACIMG.nbh, instead of just BLACIMG......so the actual file name when I looked in to it was actually sitting as BLACIMG.nbh.nbh
Once I'd deleted the .nbh extension out of the file name I renamed it worked.
deafpotato said:
Hi All,
I have tried searching for the answer to this question and cannot find it, though I am sure I wont be the first to have had this problem.
I am trying to flash a new rom on my touch HD, have tried two different ones - duttys and black pearl. I have managed to get the upsl to work in the bootloader but i cannot get a rom to boot from the SD card. I have followed the instructions on the pages with the roms (same in each) and all i see is a screen flash up after running uspl saying "no image file" then it goes back to the bootloader screen.
In order to get out of bootloader I have to remove my battery which i assume is normal and then it goes back to the normal spl.
I am pulling my hair out on this one - and I dont have much to pull on!
I didnt think it would be so hard with all of the instructions about!
Click to expand...
Click to collapse
Did you remove storage card before entering Bootloader screen? Put storage card in after Bootloader is up and before opening USPL.
USPL HowTo
Sorry to ask again.
I had the same problems.
As I couldn't do with USPL (just did not find reasonable step-by-step instructions), I used OliNex HardSPL which worked fine.
But now with new ROM updates, I face significant problems with display color and radio not working.
So, I actually definitely need and would like to ask somebody to take the time to post ...
step-by-step instructions on how to use USPL
PLEASE !
USPL HowTo
Obviously, I just missed out one point and needed to change another.
But for those in the same situation:
Probably only works on Windows XP, didn't work on my Vista PC.
(1) Download the latest USPL (currently 2.5)
(2) extract anywhere on your computer
(3) Go to ActiveSync properties and disable "Allow USB Connections" option
(4) Turn off your device (long press "Power" key or remove/replace battery)
(5) then enter SPL bootloader mode (tri-color)
- Blackstone: when device turned off by pressing and holding "VolDown" key plus "Soft Reset" simultaneously
- did NOT work for me: by pressing and holding "Power" and "VolDown" keys simultaneously.
(6) Connect USB cable and make sure "USB" label appeared in the white portion of the screen on your device.
(7) start / run "cmd" (DOS console) on your desktop PC
(8) Execute blac_uspl.exe in DOS window
current status and any error messages USPL encounters will be displayed in the console window.
(9) If everything goes well, your device will restart and SPL version label should read "1.15.USPL" indicating that USPL was loaded successfully.
You ever read through the USPL thread?
stepw said:
10. How to use it?
Download the latest USPL attached to the second post of this thread and extract anywhere on your computer.
Go to ActiveSync properties and disable "Allow USB Connections" option. Turn off your device (long press "Power" key or remove/replace battery), then enter SPL bootloader mode (tri-color) by pressing and holding "Power" and "VolDown" keys simultaneously.
Connect USB cable and make sure "USB" label appeared in the white portion of the screen on your device.
Execute blac_uspl.exe; current status and any error messages USPL encounters will be displayed in the console window.
If everything goes well, your device will restart and SPL version label should read "1.14.USPL" indicating that USPL was loaded successfully.
If SPL version does not include "USPL" or if the screen is black, soft reset and try again. If "USB" label disappeared and did not reappear, reinsert USB cable.
You can then start RUU update to flash RUU_signed.nbh. Once RUU update is completed, device will restart using regular flashed SPL.
If you want to flash from SD card instead, make sure your SD card is not inserted when you enter the bootloader originally.
SPL will try to install it and would fail if blacimg.nbh is not signed by HTC. Insert the card after "USB" label comes up in SPL but before running USPL.
You can run "blac_uspl.exe ?" to get command line parameter help. Only 1 parameter is accepted and that is the name of an SPL file you want to load. You can load an MFG SPL or HSPL. USPL automatically takes care of allowing unsigned/cooked ROM flashing with any SPL you use.
Click to expand...
Click to collapse
Should be just clear, isn't it? Have used it a few times, without any problems ...
No, it probably wasn't clear enough.
At least it didn't work for me.
see the changes I applied above (plus minor additions)
remove the memroy card!
the first time i tried the upgrade, it failed... because my memory card was inside the phone. worse, the mem card contains the rom upgrade file.
pls remove the memory card first.. then run the ruu update.
after which, it will state that rom is 1.15.
then can insert memory card (only if u see the USB word on your phone)
then can re-run program.. and update firmware..
I have experienced this problem where no image file was found when flashing from UPSL. I think this is some kind of random **** that happens. I have flashed countless ROM with this method and sometimes this **** just happens without any reason.
hi, how come my tri-color bootloader only shown "Serial" in the white portion of the screen? Is there something wrong with my HTC HD phone? I try to reflash the ROM thru this way since ActiveSync cannot detect my HD. My HD phone only shown battery charging whenever I plugged in the mini-USB cable into the computer.
Anyone can enlighten my issues? Thank you in advance!
I met the same issue, and I solved it by re-formatting the card using FAT32.
MOD EDIT
I'm closing this thread as dummies guide, USPL & HSPL threads already exist.
If your having still having difficulties post your query into relevant thread. I'd suggest you start with dummies flashing guide thread.
Thread closed
hi sir iam new in this forum plz help me my htc hd2 shows on screen software update failed it cannot connected to active sync but connected to my pc .i download its hspl and rom butt next what can i do plz help me.
Try to get it into bootloader by taking out your battery, putting it back in, and then holding the volume down button while pressing the pwr/end key.
You have to hold the vol- key while the phone starts up, then you should see a screen with a few colores bars and some info.
EXACTLY what all info is displayed in your tri-color (bootloader) screen?
i tried the same. phone is in boot loader mode butt cannot connect to hspl2 it gives error plz help me .what can i do next its spl is 2.08.0000 8G XE
Don't bother trying to flash it via ActiveSync or Windows Mobile Device Center on your computer. If it has already failed, it will likely fail again.
Get a class 2, 4gb sd card, and erase all files and format it (FAT32).
Get a ROM that you are CERTAIN is compatible with your 1024 Leo (TMo-US) and inside the zip file you will find a file with the extension .nbh
Rename it to LEOIMG.nbh and transfer the file to your freshly formatted 4gb class2 card. (Not inside any folders, just on the card)
Take the battery out of your phone, then place the sd card into the phone.
Turn the phone on while holding the vol- button, to enter bootloader, and your phone will detect the LEOIMG.nbh file after a few seconds and ask you if you want to update your software.
Your phone will tell you to press a button to start the update. Press the button. Wait for the update to complete. The phone may reboot and flash the update again, I've had mine do that, it's okay, just let it go.
When everything is done, it should either turn off by its self, or boot up normally by its self.
If the update fails the first time, try it again.
Turn it off, take out the sd card, and boot it up normally.
If you follow these steps exactly, then you will not fail.
If you do follow thes steps exactly and the phone doesn't get all the way thru the update process, and fails, then it's one of two things:
1. You tried to flash an incompatible ROM
2. There's something wrong with the hardware of your phone, or your bootloader is corrupted.
Good luck and happy flashing!!!!!
bro thank u for give me complete detail for that butt i am confused that where i find compatibale rom.plz if u up load for me that rom and if possible how to find the file LEOIMG.nbh.plz sorry for my bad english. my phone spl is 2.08.000.and also that software windows Mobile Device Center.
usmancheema said:
bro thank u for give me complete detail for that butt i am confused that where i find compatibale rom.plz if u up load for me that rom and if possible how to find the file LEOIMG.nbh.plz sorry for my bad english. my phone spl is 2.08.000.and also that software windows Mobile Device Center.
Click to expand...
Click to collapse
OK since your SPL is 2.08, you will first need to install HSPL to your phone through your computer.
Don't worry, HSPL never fails over the computer , as ROMs sometimes do.
http://forum.xda-developers.com/attachment.php?attachmentid=347299&d=1277158888
Just connect your phone through Windows Mobile Device Center and run the HSPL program (right-click it and Run As Administrator), following the instructions the program gives you. When asked to choose an SPL, choose 2.08 HSPL.
Allow the program to work its magic, and when it is finished, go into bootloader and confirm manually that you have HSPL by looking on the bootloader screen for the name Cotulla, and it should say 2.08HSPL
Then I would suggest any of the ROMs here:
http://hotfile.com/list/588162/580b43d
Personally I would go with the Dinik one, the icons and everything are really nice looking.
Just follow my previous instructions to flash it via sd card, and you'll be good to go.
After that, go learn about putting some Android builds on your sd card in the HD2 forum, Android subfora.
Lots of fun to be had there.
Hope it all works well for you, don't hesitate to ask more ?'s if you're not sure about something
my phone wont bootup,frose when the htc logo and the text arive.what can i do? got no activesync contact.. The phone is original..
i installed the original RUU now,but still the same..
which version?... did you remove memory card and sim card during flash.... if not remove and try again...
if that doesnt work try this - extract ruu.exe and rename ruu signed.nbh to LEOIMG.nbh copy to memory card and insert to phone... enter bootloader mode by turning on phone while pressing volume down until you see three color in you screen and follow what it says wait until it finish - Complete...
make sure you have battery ... and check if phone gets hot during flash period
if no success write again and we will try to help you
best regards from me - sorry for my English
this is what i tryed to install.. if i dont remember wrong it should be tha same on the phone from before..
RUU_Leo_S_HTC_NOR_3.14.409.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe
i removed the sim and the memorycard.
copy only leoimg to card or all files?
thanx!!
i tried with the one file.. the white screen with all the text arrived. but behind the radio,rcust,bootloader,splash1,os,configdata it saids nothing? is that right??
beemerfanatic said:
this is what i tryed to install.. if i dont remember wrong it should be tha same on the phone from before..
RUU_Leo_S_HTC_NOR_3.14.409.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe
i removed the sim and the memorycard.
copy only leoimg to card or all files?
thanx!!
Click to expand...
Click to collapse
ok...
where did you download that rom... to make sure go to htc web page and download rom with your phone serial number( if you already did that skip this step)
enter in to bootloader and write what you see... just to make sure if you have hardspl or stock spl ( enter bootloader mode by turning on phone while pressing volume down until you see three color screen remove - memory card)...
copy Just LEOIMG.nbh to memory card - not in folder, it would be better if you format memory card ... make sure its fat32 formated...
Before you try memory card option show what you see in bootloader....
can you explain what were you doing when this happened
beemerfanatic said:
i tried with the one file.. the white screen with all the text arrived. but behind the radio,rcust,bootloader,splash1,os,configdata it saids nothing? is that right??
Click to expand...
Click to collapse
no it should say OK for every step until it says successfully Complete
ah,now it starts with OK behind
the ruu is from the htc site.. the flash is complete. but no luck,still the same..
this is what i got..
PB81100 HX-BC
SPL-3.03.000 XE
i didnt do enything,i was goint to take a call,but the phone was sudently dead. i turned it on,and then it frose at bootup.
says at bootup:
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
does you phone get hot...
write hardspl
http://forum.xda-developers.com/showpost.php?p=5279236&postcount=4
apply task 29
http://forum.xda-developers.com/showthread.php?t=644781&highlight=task+29
try again memory card method to flash again - after task 29
if still have frose try a nother rom stock ... if that fails try a costum rom ... or go for android or wp7...
best regards from me
the phone is not very hot no..
point one and two are done. when doing nr two it saids nothing on my rom? strange..
Installing again now from memorycard.. x my fingers
frose again.. ****..
well all i can say is write hardspl again and write other stock rom - you can get here
Code:
http://shipped-roms.com/index.php?category=windows%20mobile&model=Leo
dont flash tmobile roms
if you write roms under 3.14 install hardspl 2.08.... if you install hardspl 3.03 go with 3.14 roms
if still no success try costum roms
http://forum.xda-developers.com/forumdisplay.php?f=534
this build is great it has Norway language too
http://forum.xda-developers.com/showthread.php?t=612580
follow instructions very carefully
i hope you will success
i have to go now see you tomorrow
best regards from me
thanx for all the help! Phone works perfect! love the artemis rom! awsome!
very happy
beemerfanatic said:
thanx for all the help! Phone works perfect! love the artemis rom! awsome!
Click to expand...
Click to collapse
im glad for you ... but believe me when i say im very happy for helping you...
best regards from me
I`m writing this after almost a full day of searching and testing with no luck.
I have friend who tried to upgrade Rom into his Touch HD and failed.
Right now all the phone does is to start in tricolor menu. I have tried several Roms but when trying to flash they get stuck at 0% and after a while it ends up with error 262. Same thing happens when trying to upgrade to HSPL also (i do not have a working Rom on this phone, just a tricolor menu which starts automatically when phone started ). I have tried to flash rom with SD card (2Gb), and with Ruu with Win7 and XP.
Info :
Blac100 32M
SPL-1.54.0000
MicroP-Blackstone (LED) V6
How can i recover this phone? Can anyone pls help me ?
I have attached a Print screen of my folder dedicated to this phone. Everything there i have tried.
oh my god...you tried to flash a ROM without SPL!? are zou crazy? first you have to flash HSPL, search for the latest spl 1.56 olinex and when you get the (.nbh) file, name it to Blacimg.nbh and put on SD card (on root!) then it will appear a confirming message to install the .nbh, and you confirm.
note: not having HSPL is pratically the same thing has having a locked bootloader...
mfsr98 said:
oh my god...you tried to flash a ROM without SPL!? are zou crazy? first you have to flash HSPL, search for the latest spl 1.56 olinex and when you get the (.nbh) file, name it to Blacimg.nbh and put on SD card (on root!) then it will appear a confirming message to install the .nbh, and you confirm.
note: not having HSPL is pratically the same thing has having a locked bootloader...
Click to expand...
Click to collapse
Yes i know... not me was the one who tried... i have received it like this, and trying to recover it. The idea is when trying to install HSPL it get stuck at 0%, and the alternate method implies booting into system... but i do not have a system on device. I have also tried to download the official rom from HTC website.... and after 1% it says "invalid vender ID".
Flash SPL from sd card. Name the file as BLACimg.nbh and put on sd root. Then enter Tricolor screen (If it doesnt go automatically) and confirm the flashing. Then SEE If you get the htc logo and a empty shell ( black screen) . If you do good, now normally Flash a ROM ( you can use sd method or throug pc
---------- Post added at 03:26 PM ---------- Previous post was at 03:24 PM ----------
If it doesnt work try another sd
This what i`m trying, but it get stuck to "loading" . I have downloaded "HSPLWrapper_Blackstone_156OliNex" , started "HSPLWrapper_Blackstone_156OliNex.exe" , nbh file apeared in same folder, copied to SD (formated to Fat32, default alocation unit) started phone, gone in tricolor then "loading" message on screen and nothing else (for 10 minutes already).
hmmm... keep waiting
finaly solved
I have finaly solved it. First you need Windows XP on PC. Download USPL 2.5 and open a CMD window. Start utility to upgrade to HSPL OLINEX and after presing update , and progres bar apears on phone execute fast the uspl in cmd window (otherwise it will say it cannot open USB port). After this you phone will reboot in tricolor but instead of SPL you will se USPL 1.14. Disconect usb from phone and reconect it, now it should say is connected to USB. Relaunch the HSPL update utility and wait to get to 100%. When done phone will reboot into system (if you have any).
its a way, but you could simply flash hspl trough sd (use other sd if that doesnt work, I needed to cange too!)
mfsr98 said:
its a way, but you could simply flash hspl trough sd (use other sd if that doesnt work, I needed to cange too!)
Click to expand...
Click to collapse
Believe me ! i have tried with four different SD cards, one of them indeed did not worked (a 4Gb). I do not know exactly what happened to the phone but it was impossible to flash anything to that phone (except some shipped roms witch would fail after 1% with invalid vender ID on pc and some 28008 error via card) . As i said one post earlier, the only way was via USPL, witch needed a workaround method (because it too failed with "could not access usb port" error). And the USPL worked only on Win XP and had a very narrow time window to execute the file (to have the USB port accessible ). After changing to SPL 1.56 Olinex phone booted with the old WM 6.1 stock. But i have changed 3 other roms after that, finally settling to energy Rom. With Olinex i had no problem at all flashing the Roms. I have even flashed a new radio, with absolutely no problem. Don't know what was the problem exactly, but the old SPL 1.54 had some serious issues !
I`m just glad i have revived this phone (witch btw, is not even mine)....
the old SPL, was locked lol. It's the stock SPL straight from HTC. But doesnt matter, good thing you solved your problem
10x
Wow, thanks alot for this post. I've done the same thing as you and crashed my HTC. Problem solved with Win XP, but more simple. Just executed USPL.exe and, job done. I think in Win7 was the problem with certified drivers. Think that can be solved in a fresh instalation of Win7 but not with certified microsoft drivers or HTC Sync installed. Anyways thanks alot. You've been a lifesaver.