ERROR[270]-Please help - P3600 General

I am trying to upgrate my trinity.
With every Rom after 1% of updating shows the following message "ERROR[270]
The image file is corrupted.Please check your update utility"
Any ideas??
Thanks

you must use hardspl
you must use hardspl

puiutz_bv said:
you must use hardspl
Click to expand...
Click to collapse
是不是没有解锁 刷spl到1.30

乌鸦炸酱面 said:
是不是没有解锁 刷spl到1.30
Click to expand...
Click to collapse
Safest to use 1.20 Olipro
I PMd you iwsidiro

Related

Anyone has Qtek s200 original ship WWE rom?

Can anyone help?
Sorry, i dont know how to upload. But look here :
http://www.extendedsystems.dk/downl...phet_2100728_21007109_020720_QtekDAN_Ship.exe
Hi,
This is not a WWE version but a Danish (I've flashed it ).
I've uploaded it here:
ftp://xda:[email protected]_2100728_21007109_020720_QtekDAN_Ship.exe
This is not WWE file.
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
jaxf250 said:
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
Click to expand...
Click to collapse
I download it already but dont know how to burn *.nba file to SD card.
Can you give me some experience about this ?
Thanks in advance.
jaxf250 said:
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
Click to expand...
Click to collapse
Thankss
After reading some postes here I've done. My OS now become 2.9.7.24. But when I trying to flash Radio nba, I always get error ...
Br
ta_mobile said:
But when I trying to flash Radio nba, I always get error ...
Br
Click to expand...
Click to collapse
read http://forum.xda-developers.com/viewtopic.php?t=42751&start=25 again
jaxf250 said:
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
Click to expand...
Click to collapse
Hi jaxf250
How do you explode it too pieces, i looked and looked round the forum but cant figure it out.
bho12 said:
jaxf250 said:
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
Click to expand...
Click to collapse
Hi jaxf250
How do you explode it too pieces, i looked and looked round the forum but cant figure it out.
Click to expand...
Click to collapse
Read link below and use the aWizard tools to explode ROM and re-assemble:
Click here --> http://forum.xda-developers.com/viewtopic.php?t=37386
Qtek S200 cannot be CID-unlocked, so awizard is not useful!!!
ta_mobile said:
jaxf250 said:
It's here in pieces - you need aWizard to install it. It's not a self-installing EXE....
ftp://ftp.xda-developers.com/Uploads/S200
Click to expand...
Click to collapse
I download it already but dont know how to burn *.nba file to SD card.
Can you give me some experience about this ?
Thanks in advance.
Click to expand...
Click to collapse
This is not the same as the file bho12 refers to.
Could anyone upload to ftp the danish qtek shipped rom, from a aWizard dump. Using the exe file, only returns the error [924]: "invalid vendor id" for me.
I would like this rom on my s200, since it seems like the only way to solve the t9 issue... thus getting t9 in danish on my s200 wwe.
Hope someone can help :roll:

CID unlock problem

Please how unlock the CID .... upgrade (downgrade) is no funkcion.
I have 1.8. WWE version HTC and I like dopod ROM...
thank you very much
check:
http://www.imei-check.co.uk
I know a way to let Hermes to get SUPERCID by using HTC_Hermes_SIM_Unlock_v2a,can I use this software to unlock the Herald CID?Thanks!!!
ywl3k said:
I know a way to let Hermes to get SUPERCID by using HTC_Hermes_SIM_Unlock_v2a,can I use this software to unlock the Herald CID?Thanks!!!
Click to expand...
Click to collapse
it can't!!!!!!
wlinsong said:
it can't!!!!!!
Click to expand...
Click to collapse
100% positive????
wlinsong said:
it can't!!!!!!
Click to expand...
Click to collapse
So,How Can I do that?I want to get one,and flashed the USA rom.Only can supercid can do it?!
ID64 said:
100% positive????
Click to expand...
Click to collapse
Now we cannot do it.
Hi Can anybody please provide me with some information on howto unlock Herald with http://www.imei-check.co.uk/... ?
I have bricked my Herald, can only get into Bootloader - Is it possible to do the unlock when no System is installed ?
THX !
Sorry but with iemei-check you need to have OS running, and have to have an ActiveSync connection, READ what is said on the site itself, you could have found the awnser yourself

Need HELP WM6 Feeler

HELP
i tryed to flash WM6 on my SP3i, i used this manual and files http://www.geocities.com/gggbitonti/typhoon.htm
after first step my device went into bootloader and i can`t do anything with it..
i tryed to flash oficial rom (2003), but it not takes me effect
My device is not Cidunlock
Sorry for my English
felicita said:
HELP
i tryed to flash WM6 on my SP3i, i used this manual and files http://www.geocities.com/gggbitonti/typhoon.htm
after first step my device went into bootloader and i can`t do anything with it..
i tryed to flash oficial rom (2003), but it not takes me effect
My device is not Cidunlock
Sorry for my English
Click to expand...
Click to collapse
what dose is say on the bootloader
rickwyatt said:
what dose is say on the bootloader
Click to expand...
Click to collapse
Typhoon
IPL 1.00
Typhoon
SPL 2.5.0107
Typhoon
felicita said:
Typhoon
IPL 1.00
Typhoon
SPL 2.5.0107
Typhoon
Click to expand...
Click to collapse
You must make SuperCid!
http://www.user.cityline.ru/~ronswens/Tutorials.htm
Reply With Quote
moalesipufos said:
You must make SuperCid!
http://www.user.cityline.ru/~ronswens/Tutorials.htm
Reply With Quote
Click to expand...
Click to collapse
Sorry, device is SUPERCID!!!But i still can`t flash rom

White Bootloader Screen

My unit is working fine..can make receieve calls etc...
Am running on Meschle's 2.11 lite....hard reset fine everything fine...
When I try to upgrade to the full version - Gives me error...Connection.check cradle etc...
Tried Official ROM - same problem
Tried Manual Bootloader - goes into a white screen and hangs...then after 4-5 minutes i see the colored screen with IPL 3.04.0001 and SPL 1.11.000...
if I reset goes back to the ROM that was there on it...works fine...
Did I just brick my phone?
Not that I am not happy with it...but then why the Bootloader and flashing is not working?
Try the official dopod version from here.
NOTE: it will change ipl, spl and gsm radio versions.
After that run uspl again before tryin any other rom
NikMel said:
Try the official dopod version from here.
NOTE: it will change ipl, spl and gsm radio versions.
After that run uspl again before tryin any other rom
Click to expand...
Click to collapse
Thanks a million...it worked re-flashing the official version now !
phew !
I think it's high time - i gave my orbit a rest rest from all the ROMming..
hehe
nice
devdarshan said:
Thanks a million...it worked re-flashing the official version now !
phew !
I think it's high time - i gave my orbit a rest rest from all the ROMming..
Click to expand...
Click to collapse
NikMel said:
nice
Click to expand...
Click to collapse
Hi Nikmei, do you need to tun uspl first before flash the official dopod rom, thanks
This method is only for an extreme case like when you can’t boot!
Do not use this method for update w/out the uspl.
tongphan said:
Hi Nikmei, do you need to tun uspl first before flash the official dopod rom, thanks
Click to expand...
Click to collapse
NikMel said:
This method is only for an extreme case like when you can’t boot!
Do not use this method for update w/out the uspl.
Click to expand...
Click to collapse
thanks , when i try to run upsl it got to 70% the the screen turn off and a pengune picture, what should i do now, thanks
If you really want to flash your pda then you better hard reset it then uspl will work for 100%.
Normally if you run uspl you should get a blank screen and after that you can goon with the update wizard.
tongphan said:
thanks , when i try to run upsl it got to 70% the the screen turn off and a pengune picture, what should i do now, thanks
Click to expand...
Click to collapse
NikMel said:
If you really want to flash your pda then you better hard reset it then uspl will work for 100%.
Normally if you run uspl you should get a blank screen and after that you can goon with the update wizard.
Click to expand...
Click to collapse
NikMel, i have the dopod m700, try to run the upsl few times before flash to wm6 rom, every time it went to 70% the screen went off, please help
I can't tell you for sure if this procedure will work for your pda.
this works on artemis or p3300 or dopod p800
tongphan said:
NikMel, i have the dopod m700, try to run the upsl few times before flash to wm6 rom, every time it went to 70% the screen went off, please help
Click to expand...
Click to collapse
NikMel,
you just saved me alot of money.
I just ordered a new mobile device yesterday because I thought I had bricked my device.
Fortunately I found this post and was able to reflash the device with this rom. So I have cancelled the order.
Thank you so much!!!
I would love to donate to you if you have paypal
If you would then send it to this forum.
Sorry but I dont know how you can do it.
Arura said:
NikMel,
you just saved me alot of money.
I just ordered a new mobile device yesterday because I thought I had bricked my device.
Fortunately I found this post and was able to reflash the device with this rom. So I have cancelled the order.
Thank you so much!!!
I would love to donate to you if you have paypal
Click to expand...
Click to collapse
NikMel said:
If you would then send it to this forum.
Sorry but I dont know how you can do it.
Click to expand...
Click to collapse
Found donate! link in the bar.
hehe OK
Arura said:
Found donate! link in the bar.
Click to expand...
Click to collapse
NikMel said:
hehe OK
Click to expand...
Click to collapse
I meant navigation bar!

[Q] Help mw pls!!!

I want to remove Olipro 3.20 from my HTC P3600i
How can i do??
(Sorry for my bad english)
gotji said:
I want to remove Olipro 3.20 from my HTC P3600i
How can i do??
(Sorry for my bad english)
Click to expand...
Click to collapse
you need downgrade to Olipro's Hard-SPL 1.20 or Olipro's Hard-SPL 1.30
Olipro 1.2
But i try to run SSPL it show black screen
it not show tri-screen.
How can i fix it ???
gotji said:
Olipro 1.2
But i try to run SSPL it show black screen
it not show tri-screen.
How can i fix it ???
Click to expand...
Click to collapse
to fix it, you can look post at http://forum.xda-developers.com/showpost.php?p=4353623&postcount=1
This link was expire. Do you have any link??
gotji said:
This link was expire. Do you have any link??
Click to expand...
Click to collapse
I am very sad... for not knowing the other links (mirrors), we suggest you try making your own NBH file to recover stuck HardSPL 1.20 by following the instructions given
Thx. I will try it

Categories

Resources