BA wm6.1 no longer bootup aka white screen & stuck bootloader - MDA III, XDA III, PDA2k, 9090 ROM Development

I have read the wiki, did a search on this forum on white screen, stuck on bootloader and tried the following...
- reflashing the same rom wm6.1
- normal reset will stuck at 4 colors bootloader.
- hard reset with NO, YES, YES option will stuck at white screen.
- downgraded to wm2003
- downgrade success but still stuck at bootloader
Is there anything else I can try!

try flashing using mtty. (google it)

krishan2207 said:
try flashing using mtty. (google it)
Click to expand...
Click to collapse
Tried mtty method, doesn't help either.
Thanks anyway!

I have read all the thread relating to "white screen", "stuck at bootup", "hard reset" with the option No/Yes/Yes every after flashing. this never fails".
Guess my BA is as good as gone!
Strange that I can still flash the BA with various rom from stock to wm6x as well as all version of the radio.
With 2003se, I get stuck at bootup with the O2 logo.
With WM6x, I get stuck on bootup.
When I do a hard reset" with the option No/Yes/Yes, I get a white screen.
This has gotto be the PITA mother of all BA problems.

There is something else that you could try. I remember not too long ago, I saw a method for unbricking Wizards (I nearly did with my wife's old phone) and it said something about doing something via mtty. This was not flashing the rom, but rather something else. +Que PPC might know what I am talking about. In fact, I believe that I saw that method in his signature. PM him and ask him. I will try to find out what I did and I will reply to this (if I can find it )
Edit: Try this
There are a couple of other threads in the Wizard section, so take a look over there and look for something that is not exactly flashing, but that deals with mtty. Alternatively, you could try to pm xplode regarding your problem. I haven't seen him around lately, but he will show up eventually.

Thanks for your reply and links. I did try that but it didn't work.
Anyone who has a ROM dumped of an original O2IIs to SD card?

you should be good by mtty method, search the board for stuck in bootloader
if ot does not help your bootloader is corrupted

xplode said:
you should be good by mtty method, search the board for stuck in bootloader
if ot does not help your bootloader is corrupted
Click to expand...
Click to collapse
Man! Good to see you are still around! I haven't seen you in a while...

xplode said:
you should be good by mtty method, search the board for stuck in bootloader
if ot does not help your bootloader is corrupted
Click to expand...
Click to collapse
Are you referring to the
set 14 0
task 28
task 28 55aa
method? I have tried all these.
Any fix for bootloader?
Thanks Xplode!

hello world!

hi there...
where did you get your wm2003se downgrade??
wm6.5 on my BA is quite slow...

you can probably find the firmware at your carrier's site, or you have a look in -=xplode's firmware archive=- and look for your original firmware there.

Related

Help with my Bricked 8125

I think my 8125 is bricked. I've never had a problem flashing roms until yesterday I tried Farias Kitchen ROM. I flashing went through ok like normal, but when it restarted, it gets a little bit after the second splash screen. The green windows mobile with farias names at the bottom loads, then the topbar of windows mobile loads with the start button, but then nothing else.
I've tried reflashing it in forced bootload mode as well as doing a hard reset. no luck. The update utility keeps telling me that it is an invalid update tool, please get a newer update utility. I've tried taking the battery out for a while and from there doing forced bootloader. Still no luck
Any suggestions?
daddy_yankee1980 said:
I think my 8125 is bricked. I've never had a problem flashing roms until yesterday I tried Farias Kitchen ROM. I flashing went through ok like normal, but when it restarted, it gets a little bit after the second splash screen. The green windows mobile with farias names at the bottom loads, then the topbar of windows mobile loads with the start button, but then nothing else.
I've tried reflashing it in forced bootload mode as well as doing a hard reset. no luck. The update utility keeps telling me that it is an invalid update tool, please get a newer update utility. I've tried taking the battery out for a while and from there doing forced bootloader. Still no luck
Any suggestions?
Click to expand...
Click to collapse
What are you trying to re-flash it with in the BL?
You should be able to flash the loverom without a problem.
TaurusBullba said:
What are you trying to re-flash it with in the BL?
You should be able to flash the loverom without a problem.
Click to expand...
Click to collapse
Thanks, I'm gonna download it right now and try it. What is different about this ROM than any of the cooked roms I have already as well as and official one. All of them in past have worked for me without a problem until now.
daddy_yankee1980 said:
Thanks, I'm gonna download it right now and try it. What is different about this ROM than any of the cooked roms I have already as well as and official one. All of them in past have worked for me without a problem until now.
Click to expand...
Click to collapse
Well, it sounds like it may have just been a bad casserole you cooked.
But, you could probably even re-flash using your carrier ROM. This one is just a fool-proof way to get you back on your feet. This ROM is just G3/G4 independent and doesn't include a radio, ipl/spl, or extrom.
TaurusBullba said:
Well, it sounds like it may have just been a bad casserole you cooked.
But, you could probably even re-flash using your carrier ROM. This one is just a fool-proof way to get you back on your feet. This ROM is just G3/G4 independent and doesn't include a radio, ipl/spl, or extrom.
Click to expand...
Click to collapse
Nope, just tried flashing that ROM mentioned above, and still the same answer. It keeps telling me that I need to get a new update utility. That is so weird because I never had that problem. I have already tried flashing the official as well with no luck.
daddy_yankee1980 said:
Nope, just tried flashing that ROM mentioned above, and still the same answer. It keeps telling me that I need to get a new update utility. That is so weird because I never had that problem. I have already tried flashing the official as well with no luck.
Click to expand...
Click to collapse
So, how exactly are you updating it in the bootloader? (just curious)
TaurusBullba said:
So, how exactly are you updating it in the bootloader? (just curious)
Click to expand...
Click to collapse
I put the phone in bootload mode by pressing and holding the camera button, then resetting by pushing the reset hole which then loads it to a colorful screen which I assume is the bootloader screen. Then I just connect it and try to flash it using one of the ROMS i have. Thats how I did it the past couple of times.
What upgrade utility are you using? You might wanna try the one attached! It is the 'NO_ID' version and up to now it flashed everything! Simply extract the zip file to a folder on your desktop, then copy your nbf file in to it too and run the "ROMUpdateUtility_Wizard_NoID.exe"
hello
im having the same problem, i just tried it, didnt work for me
Did you CID unlock your phone before trying to flash it? Did you also try to flash it with your shipped ROM again?
My phone also appears to be bricked. It locked at 99%, and after trying the steps indicated in the core2.0 installer, it closed, and I'm having difficulty figuring out the next step. As is, I get ERROR [264] CONNECTION. Is there a way to get the phone functional enough to load an OS? I've been searching these forums for about 30 minutes and haven't found what I'm looking for. There should be a recovery wiki.
I have the same problem...
Junner2003 said:
Did you CID unlock your phone before trying to flash it? Did you also try to flash it with your shipped ROM again?
Click to expand...
Click to collapse
Hi Junner, i have the same problem too...i did a unlock CID before i try to put the core 2...but after the boot its freeze on splash screen and nothing happend...what can i do? help me please...tks a lot.
alissonguedes said:
Hi Junner, i have the same problem too...i did a unlock CID before i try to put the core 2...but after the boot its freeze on splash screen and nothing happend...what can i do? help me please...tks a lot.
Click to expand...
Click to collapse
First thing you could try is to flash it with your shipped ROM again (the one you had on there originally). If that does not work you might want to search the forum for the LOVE ROM ??? I never tried that one but people say it should worke on any device (G3 /G4).
I thing more
alissonguedes said:
Hi Junner, i have the same problem too...i did a unlock CID before i try to put the core 2...but after the boot its freeze on splash screen and nothing happend...what can i do? help me please...tks a lot.
Click to expand...
Click to collapse
Every rom that i put in the phone is the same...always freeze on the splash screen...
Junner2003 said:
First thing you could try is to flash it with your shipped ROM again (the one you had on there originally). If that does not work you might want to search the forum for the LOVE ROM ??? I never tried that one but people say it should worke on any device (G3 /G4).
Click to expand...
Click to collapse
I try LOVE too and nothing...the phone is G3 with ipl/spl 1.01
alissonguedes said:
I try LOVE too and nothing...the phone is G3 with ipl/spl 1.01
Click to expand...
Click to collapse
Did you try already to flash your shipped ROM?
I dont have one
Junner2003 said:
Did you try already to flash your shipped ROM?
Click to expand...
Click to collapse
I dont have one...
You can download the Official ROM directly from HTC's site.
alissonguedes said:
I dont have one...
Click to expand...
Click to collapse
Yeah, download that one if Cingular was the original one! If not: let me know what was on there originally!
Junner2003 said:
Yeah, download that one if Cingular was the original one! If not: let me know what was on there originally!
Click to expand...
Click to collapse
A mda vario tmobile from germany...

Please help me and my MDA!!!!!

I was updating my MDA to WM6 when my computer froze in the middle of updating, so i unhooked the MDA and resset it, now its stuck on the splash screen!!!! no matter what I do! and activesync will not recogizine it also!! ive tried hard reset be all its saying issomething about a FAT partition, it can still go into bootloader mode so i know its not bricked, its a G3 model...SOmeone PLEASE help!!!!!
Nolimit1211 said:
I was updating my MDA to WM6 when my computer froze in the middle of updating, so i unhooked the MDA and resset it, now its stuck on the splash screen!!!! no matter what I do! and activesync will not recogizine it also!! ive tried hard reset be all its saying issomething about a FAT partition, it can still go into bootloader mode so i know its not bricked, its a G3 model...SOmeone PLEASE help!!!!!
Click to expand...
Click to collapse
Read the wiki for wizard, I am sure God will help u if u help urself. I think it can be restored by going into the bootloader.
NEww problem
Thanks, did some reading and solved it, but than i wanted a new rom and when i installed it I started and it stuck at splashscreen again, only now hard reset fails and now matter what original tmobile rom i flash it to its still stuck!!! Please help!
Nolimit1211 said:
Thanks, did some reading and solved it, but than i wanted a new rom and when i installed it I started and it stuck at splashscreen again, only now hard reset fails and now matter what original tmobile rom i flash it to its still stuck!!! Please help!
Click to expand...
Click to collapse
What steps have you taken, and where are you stuck at now? Can you bring it into bootloader mode? What IPL/SPL? You said its G3, is it CID unlocked?
So far i have flashed it with the original Tmobile rom and some others through the bootloader mode, but even after it says flash completed I still get stuck on the splash screen, my ip/spl are both 2.26, and it is CID locked, and at the time i dont had a mini sd card to perform an sd rom upgrade, god i wish i just stuck with my original rom, please help!
Nolimit1211 said:
So far i have flashed it with the original Tmobile rom and some others through the bootloader mode, but even after it says flash completed I still get stuck on the splash screen, my ip/spl are both 2.26, and it is CID locked, and at the time i dont had a mini sd card to perform an sd rom upgrade, god i wish i just stuck with my original rom, please help!
Click to expand...
Click to collapse
So you've flashed back the oroginal tmobile rom, is that also 2.26? I presume you are using the standard update util for the flash and it says completed? I've seen the update util do that (say 100% complete but not actually update anything) .. this behaviour is documented somewhere in this forum (took me about 8 flashes and a lot of confusion and frustration before I found the forum threads!) this only happened on a CID locked phone flashing a custom rom.. i don't think that happens with original vendor roms..
Can't say I have had the same problem. From looking at the forum, most people who get stuck like this can flash the wizard love rom and get back on. For me, I have mostly been able to get back to the original rom when needed, except when I bricked my G4 phone (before G3/G4 was well understood)...
Yes sir that is also a 2.26 and yes im using the standerd methodhat is this wiazrd love rom your talking about though? Maybe i should flash it to that instead of the original tmobile rom?
p.s if this only happens on cid locked phones, is there anyway to unlock my cid while in bootloader mode?
Nolimit1211 said:
Yes sir that is also a 2.26 and yes im using the standerd methodhat is this wiazrd love rom your talking about though? Maybe i should flash it to that instead of the original tmobile rom?
Click to expand...
Click to collapse
Like I said I had not used it myself, but there are many references to it in the forums.
When you say you are stuck, does it load the Windows splash screen or does it get stuck on the IPL/SPL screen?
It gets stuck on the IPL/SPL screen
Nolimit1211 said:
p.s if this only happens on cid locked phones, is there anyway to unlock my cid while in bootloader mode?
Click to expand...
Click to collapse
No you can't CID unlock in bootloader mode.. there are a number of threads on how to CID unlock...
Thanks for you assisting me sooo much, im going to try and flash with the love rom, do you have any other tips?
Nolimit1211 said:
Thanks for you assisting me sooo much, im going to try and flash with the love rom, do you have any other tips?
Click to expand...
Click to collapse
Only that by all accounts, you should be able to get a working phone again if you can get into bootloader mode.. unless you have hardware issues. The other item that may be of problem is the extended rom which can get corrupted.
Sorry I couldn't be of more help. Good luck.
Can anyone else please help, youll be a god to me if you can help me get my MDA up and running again!!!!

Bricked Cruise? Need Help.

Okay, so I'm an idiot. I'm completely lost now. Here's the basic facts:
Hard-SPL install was unsuccessful, but I didn't notice. So I'm still with original SPL.
I started upgrading the ROM with original SPL, which of course crashes at 3 percent.
Now I can't get back into WM. It's stuck at the 'smart mobility screen'.
So the problem is: it won't let me install any ROMs because original SPL is still on there. I can't change to hard-SPL anymore either. The ROM that's on the machine doesn't seem to work anymore. When I try to install an original ROM it says I can't use this utility. I think I need to download an official ROM + installer, but I can't find any from HTC.
Alright, so skip all the noob and idiot comments please, I already know. But where do I go from here?
Please help!
Bricked Cruise
hansdekker said:
Okay, so I'm an idiot. I'm completely lost now. Here's the basic facts:
Hard-SPL install was unsuccessful, but I didn't notice. So I'm still with original SPL.
I started upgrading the ROM with original SPL, which of course crashes at 3 percent.
Now I can't get back into WM. It's stuck at the 'smart mobility screen'.
So the problem is: it won't let me install any ROMs because original SPL is still on there. I can't change to hard-SPL anymore either. The ROM that's on the machine doesn't seem to work anymore. When I try to install an original ROM it says I can't use this utility. I think I need to download an official ROM + installer, but I can't find any from HTC.
Alright, so skip all the noob and idiot comments please, I already know. But where do I go from here?
Please help!
Click to expand...
Click to collapse
First you can try a hard reset!
Here you can download the original shipped rom with installer.
ftp://xda:[email protected]_radio_sign_25.65.30.04_1.58.21.23_Ship.exe
kr.,
Frepke
Update
Update
Okay, so I did the hard reset as described here. No luck.
So I went back to the bootloader screen (original SPL) and tried the original rom and installer from the download link. Again, no luck. It says "Error [294] Invalid Vender ID. This utility cannot be used for your PDA phone. Please check your update utility." The phone was unlocked when I bought it, it's HTC branded. Is there another installer out there?
I've also tried loading several roms by putting them on SD, renamed as POLAIMG.nbh. (including the orginal rom, extracted from the downloaded installer). For the original Rom, it will say 'loading...', then 'checking...' and then it will tell me: "00028002 - not allow". Then it goes back to the three colour spl screen.
There's also a link here on the forum which I'm not sure is good advice.
Three colour screen info
Pola100
Spl-1.25.0000
Cpld-2
hansdekker said:
Update
Okay, so I did the hard reset as described here. No luck.
So I went back to the bootloader screen (original SPL) and tried the original rom and installer from the download link. Again, no luck. It says "Error [294] Invalid Vender ID. This utility cannot be used for your PDA phone. Please check your update utility." The phone was unlocked when I bought it, it's HTC branded. Is there another installer out there?
I've also tried loading several roms by putting them on SD, renamed as POLAIMG.nbh. (including the orginal rom, extracted from the downloaded installer). For the original Rom, it will say 'loading...', then 'checking...' and then it will tell me: "00028002 - not allow". Then it goes back to the three colour spl screen.
There's also a link here on the forum which I'm not sure is good advice.
Click to expand...
Click to collapse
Hi
Ths info I posted relates to the Kaiser (kaiser [nearly] equals Polaris in terms of hardware) and the MTTY is from the ELF forum.
"set 16 0" to tell bootloader to boot the OS after reset.
"task 8" to get your device formatted
I suggest the set 16 0 and a reset to see if that helps, I do advocate you searching for these commands and checking they are applicable.
The info was from this KAISER thread
http://forum.xda-developers.com/showthread.php?p=2103884
HTH
Leon
MTTY
Thanks for your advice guys.
I tried the "set 16 0" command + reset. Still same situation.
Any other tips anyone?
Darn
No more reponses?
It is probably bricked then.
So what's my next move...trash it?
hansdekker said:
No more reponses?
It is probably bricked then.
So what's my next move...trash it?
Click to expand...
Click to collapse
try flashing using sd card
Tupac_Shakur said:
try flashing using sd card
Click to expand...
Click to collapse
I think he wrote already that he tried to flash some ROMS using SD card... (POLAIMG.NBH). Not sure though if he tried re Hard-SPL'ing using the SD flash method...
So I would suggest to retry the HardSPL using the POLAIMG.NBH method (just as if the HardSPL's .NBH file was a normal ROM) if this hasn't been tried yet...
Hey you must careffuly read mtty in kaiser thread.....mtty can brick your device for entire life.....my advice to you is pm GSLEON3
he's the master of using mtty and lot of kaiser user saved by him...
Hope this can help you
cheers
The Facts
When I try to hard-spl through the SD-card, it just says "Loading..." and that's where it stays - Even if I leave it till the battery dies. I tried the 2.10 and 1.10 versions on this page.
Are you sure? This Hard SPL suit for Hermes. You have to use this: http://forum.xda-developers.com/showthread.php?t=375338
TB
Hard-SPL through SD
You're right; I did notice that - however
I had to take an nbh from this page. The reason is that the HTC Cruise Hard-SPL program I found on this page won't let me extract the rom.
I need the rom file to put in on SD!
The Hermes one probably wouldn't work anyway though, thats a good point Where to get the Polaris separate rom nbh? I haven't found it on the forums. Maybe I'm going blind...
How to flash your Polaris using the microSD card [Guide]
hansdekker said:
You're right; I did notice that - however
I had to take an nbh from this page. The reason is that the HTC Cruise Hard-SPL program I found on this page won't let me extract the rom.
I need the rom file to put in on SD!
The Hermes one probably wouldn't work anyway though, thats a good point Where to get the Polaris separate rom nbh? I haven't found it on the forums. Maybe I'm going blind...
Click to expand...
Click to collapse
Hi,
Try this thread :
http://forum.xda-developers.com/showthread.php?t=384084
How to flash your Polaris using the microSD card [Guide]
TB
It's starting to seem really hopeless
Thanks.
Same result. The screen just says "Loading..." and stays there.
hansdekker said:
Thanks.
Same result. The screen just says "Loading..." and stays there.
Click to expand...
Click to collapse
unplug usb and replug it
hansdekker said:
You're right; I did notice that - however
I had to take an nbh from this page. The reason is that the HTC Cruise Hard-SPL program I found on this page won't let me extract the rom.
I need the rom file to put in on SD!
The Hermes one probably wouldn't work anyway though, thats a good point Where to get the Polaris separate rom nbh? I haven't found it on the forums. Maybe I'm going blind...
Click to expand...
Click to collapse
1. You can not flash hard-spl with microSD method! (hard-spl flash use jumpspl to ignore cid-lock. But with microSD card method you will not use jumpspl, so you can not flash hard-spl! (and to use microSD method you have to have hard-spl on your pda)
2. If you unzip hard-spl on your pc will be an RUU_signed.nbh. This is the rom file, but you can not to flash it with microSD.
3. Your device is bricked, I think. Take it to repair!
after an unsuccessful flash, u shud never try to flash again, high chance of permanently bricking your pda. go contact GSLEON3, he saved my kaiser from bricking when i made the same mistake as u. helpful fellow. make sure u donate lol
Accepted Defeat
Hi
I accepted defeat and exchanged the unit.
Thanks for all the help.
H

format failed .. stuck on splash screen..

hey guys.. i need some help
i installed an app an asked me to restart the device.. i did
and now it's stuck on the splash screen
IPL 2.27
SPL 2.27
GSM 02.44.11
OS 2.27.1.1
and the orange brand wallpaper
what can i do? i tried to reset it and format it
but an error shows up
"Press Send to restore factory default,
Other keys to quit"
ok.. send it is
"Format FAT Partition
Format failed"
i can enter RGB bootloader (cam button+power), but i don't know what i can do??
ps: i just got it from a friend, i don't think my phone is cid-unlocked..
and i'm stuck at the splash screen and nothing to do
please help me.. tell me what can i do
Ouch.
Sounds like the built-in flash memory is bad. I'm not sure what you can do about that, short of replacing it.
No offense Reverend, but where did you hear that? Its just bad flash man! Simply enter the bootloader mode, and re-flash a new rom to your device. What program where you trying to install?
ashasaur said:
Its just bad flash man! Simply enter the bootloader mode, and re-flash a new rom to your device. What program where you trying to install?
Click to expand...
Click to collapse
something from a pocket freeware site.. "XDA-Team_Manilla2D.CAB"
it's a touchflo 2d app for today screen.. after installing it, the sistem wouldn't boot up anymore. so i tried to format, soft reset, to restore the system..
the formatting started and then gave an error and shut down immediately. i didn't even catch a glimps of that error 'cause it restarted.. and then the problem. it won't go past the operator splash screen
tried to reformat.. would't start.. format failure
..simply wow.. don't get me wrong , but i didn't knew there was a bootloader screen until this happened.. i dug up about this problem on the forum, but i can't solve it.. i don't know that much about flashing.. isn't the wizard supposed to be cid-unlocked to be able to flash it with a new rom?
or there's a rom that doesn't require the pda to be unlocked?.. cause' i think mine isn't. and, since i can't get it to boot up the os, i can't cid-unlock it after the tutorials i've found here..
and i don't want to bury it, yet
Oh you poor sole...that program that you tried to flash is notorious...I did the very same thing to mine just the other day. It doesnt work with the Wizard yet for some reason.
Now, onto your problem, yes-I think that your Wizard IS INDEED CID locked, and if that is the case, search for the Wizard LOVE ROM and flash it. It can be flashed with a CID unlocked device. Head into your bootloader mode, then start up the RUU flashing program on your PC that is included with the ROM. After it flashes, you can use the Wizard Service Tool, which is also availible via searching to CID and SIM unlock your device, and then you can put any ROM that you like onto it. I hope that helps somewhat!
If you can get it into bootloader mode, you can recover. If the phone is not unlocked, you will have to load the original service ROM for that phone.
You MIGHT get lucky by just flashing the IPL/SPL back though, now that I think about it...look at the "How to Remove HardSPL" thread for the most popular IPL/SPL sets. If this works, you won't have to put all of your custom settings and programs back on.
Myrddin Wyllt
Plz note all the IP/SPL posted in the thread 'How To Remove HardSPL' are for G4 devices and they are not meant to be flashed to a G3 device,if flashed will certainly 'Brick' the G3 device.
Whereas,here ,he has a G3 device with IPL/SPL 2.27,flashing those IPL/SPL (Bootloaders) means instant death of the phone.
koolariz
Simply,download the official stock rom of the carrier and flash it in Bootloader mode to recover back to its default status,than downgrade to IPL/SPL 1.xx to CID unlock the phone,how to CID unlock the phone, read and follow this guide carefully :-
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
zabardast_1 said:
koolariz
Simply,download the official stock rom of the carrier and flash it in Bootloader mode to recover back to its default status
Click to expand...
Click to collapse
i can't find anywhere the original one.. my wizard is in orange.ro carrier [orange spv m3000].. i tried on varios romanian discussion site's but only found radio rom's i'll keep searching...
any ideea what other kind might work with cid-locked?
i found this one on xda ftp:
Orange_SPV_M3000-FRA
Orange SPV M3000 ROM update 2.18.1.3
on ftp://[email protected]/Wizard/Roms/Orange/
If it is truth....
koolariz said:
i can't find anywhere the original one.. my wizard is in orange.ro carrier [orange spv m3000].. i tried on varios romanian discussion site's but only found radio rom's i'll keep searching...
any ideea what other kind might work with cid-locked?
i found this one on xda ftp:
Orange_SPV_M3000-FRA
Orange SPV M3000 ROM update 2.18.1.3
on ftp://[email protected]/Wizard/Roms/Orange/
Click to expand...
Click to collapse
If you have said the truth... you've got a G3 device cause your ipl spl are 2.27.
So try to install this original ROM... is for Tmobile WWE so try it.... http://rapidshare.com/files/38880130/ruu_prodigy_226102_22610105_022511_tmous_wwe_ship.exe.html
Or search on tutorials tu unlock and upgrade the wizard Love ok?
Good luck men...
And please please please read and ask before do anything, BTW now the only you can do is to runn this ROMs cause you cant get your original carriers ROM.
If this dont works... please read the thread from upgrading forum in this wizard subforum that said something like Stuck on splash screen solution DYI or something the tuttorial DEV is called Drug_store.
zabardast_1 said:
Myrddin Wyllt
Plz note all the IP/SPL posted in the thread 'How To Remove HardSPL' are for G4 devices and they are not meant to be flashed to a G3 device,if flashed will certainly 'Brick' the G3 device.
Whereas,here ,he has a G3 device with IPL/SPL 2.27,flashing those IPL/SPL (Bootloaders) means instant death of the phone.
Click to expand...
Click to collapse
Good catch. Sorry about that!
Myrddin Wyllt said:
Good catch. Sorry about that!
Click to expand...
Click to collapse
Nah! buddy,you are doing fine,its just we sometime overlook the post,it happens to all of us,so no harm done !
koolariz said:
i can't find anywhere the original one.. my wizard is in orange.ro carrier [orange spv m3000].. i tried on varios romanian discussion site's but only found radio rom's i'll keep searching...
any ideea what other kind might work with cid-locked?
i found this one on xda ftp:
Orange_SPV_M3000-FRA
Orange SPV M3000 ROM update 2.18.1.3
on ftp://[email protected]/Wizard/Roms/Orange/
Click to expand...
Click to collapse
YES ! you can try this rom or download the WWE (English) version of Orange SPV M3000 Official WM5 Rom from here :
http://www.megaupload.com/?d=5OZEILXK
zabardast_1 said:
YES ! you can try this rom or download the WWE (English) version of Orange SPV M3000 Official WM5 Rom from here :
http://www.megaupload.com/?d=5OZEILXK
Click to expand...
Click to collapse
10x a lot.. i hope it won't die on me..
LE:
i tried the O2 rom [12.18.3.103] u gave me. it doesn't start flashing.. 0% and then
quoting:ERROR "This NBF file cannot be used for your PDA phone. Please get newer NBF file."
ps: The orange one on the xda ftp server doesn't work .. it's archived and parts are missing..
Hmmm,ok,lets try this out,download 'Button's Rom 1.05' from the link posted below and check if this works out.
Otherwise,you'll have to look for official Stock Rom (Romanian),which was running on the phone before.
http://wiki.xda-developers.com/index...0for newbies
i'll try this one.. for now.. ps:your link is broken?
i just have another question.. i have a friend with the same wizard as mine, i mean in the same carrier.. is it possible cu get his rom? to dump it on SD card.. or something?
so that i may flash that rom?
LE:
i found another thing on a DIY
If you got IPL/SPL 1.xx go to G3.3. If you got 2.xx go to G3.4
G3.3 Download button rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
G3.4 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G3.5.
Click to expand...
Click to collapse
should i try the wizard_love rom?
ok,download Button's Rom 1.05 from here:-
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
also try this one :-
xda_miniS_LaunchRom
http://rapidshare.com/files/43423464/Xda_MiniS_LaunchROM_v154102.exe
and yes! you can also try Wizard_Love _Rom.
Now,its possible to back up the rom from your friend's phone,but it also have to be CID unlocked first and your device shud also be CID unlocked to flash it from the sdcard (MTTY) method.
pfff (
i've updated the rom with the Wizard_Love_2.26.10.2_WWE_Novii_CF2 and now i have a blue sci-fi splash screen with "AKU 2.3" in the top-right corner..
IPL 2.27
SPL 2.27
GSM 02.25.11
OS 2.26.10.2
same ****
won't boot up
and if i try to format, same error.. Format Failed.. so here i am again
hmmmm,try a Hard Reset,hope it works or try other roms I have posted above.
Do you have any sdcard inserted in the phone right now,take it out before flashing any rom.
koolariz said:
won't boot up
and if i try to format, same error.. Format Failed.. so here i am again
Click to expand...
Click to collapse
dude.. that's what i've been trying hard reseting it.. and i get the same error each time i try it "Format Failed"
no sd inserted.. i took it out a while ago.. cause i read on the forum to flash without it.
i begining to get desperate over here
i'll try other roms..
what else can i do than hope this works
Also take out if any sdcard or mini sd is inserted in the phone before flashing,it also causes this Format Failed problem.

Some help for beginner

Dear all,
First of all, many congratulations for the great forum and thanks for all the support given here.
Now, I recognise that problems similar to mine have been discussed elsewhere, so I apologise for opening a new post, however with all the material that I could find, I got a little bit lost, so here is the story.
Some 5 days ago, the screen on my HTC Elf stopped responding to any sort of touch. The green, red and action buttons were working but no touch screen.
I have read several posts, and concluded that one possible problem was a corrupted ROM, so I downloaded latest Onyx ROM and installed it. Phone was upgraded successfully and screen started to work again.
However, the first time I switched it off and then turned it on again, it did not boot up. It gets to the point where it displays Smart Mobility and then switches itself off. The orange light then comes on for about 6-7 seconds, then off for 1-2 seconds, and then on again......
Now it does not seem to be able to charge, but if I switch it on with the camera button on I am able to get to the ROM screen (the 'rainbow screen'), so I have hope that it is not dead.
What can I do to attempt to revive the phone please? Is there a sort of 'format' that can be given so that one can start flashing ROM, etc. from scratch?
Many thanks.
PS: Except for the above, I consider myself as a total beginner in this area.
Hearing that the touchscreen started working again after flashing the ROM, I would conclude it's a software-issue.
In the rainbow-screen, what SPL does your phone run? If it ends with 'cmon', you've installed HardSPL. That means you can flash your phone from the rainbow-screen. Given that your phone won't boot, you should try to flash a new ROM from the rainbow-screen. But first, you have to confirm that you've installed HardSPL.
Good luck!
@mrqips - many thanks for your reply.
The screen says that:
IPL 2.20.0002
SPL 1.11.0000
xumiking said:
@mrqips - many thanks for your reply.
The screen says that:
IPL 2.20.0002
SPL 1.11.0000
Click to expand...
Click to collapse
Sorry Buddy.. It seems that you didn't use HardSPL, unfortunately you won't be able to flash any other ROMs..
Yet.. You might be able to use the Gold Card Method.. Give it a try and see what would happen..
Another point is.. I'm very interested to know how did you flash Onyx ROM.. without using HardSPL nor USPL (as obvious from your IPL), I would say that you used the "White Screen Method" which is by the way.. the least safest way..
Hope That Helped...
Thanks for your feedback.
Actually, I happened to be reading the post by @sbettencourt in this thread:
http://forum.xda-developers.com/showthread.php?t=595856&highlight=smart+mobility
Here, a step-by-step approach is given to recover the phone:
"1º [PRJ] Unbricker ROM discovered (wildcard CID and Model ID)
2º Pick any shipped ROM from this thread:
If you have one P3450 -> here
If you have one P3452 -> here
After this, with luck and good work you recover the phone...
3º Then you must do CID_Unlock... You can search how to do it on Wiki or if you want i got one steps how to do it right here and you can see one video with cid_unlock on my signature..." (pasted from the thread)
I did Step 1, and updated it with the unbricker ROM using romupdateutility, and the phone was recovered! It could load, get to Windows Mobile, etc.
Then, unfortunately, when I did Step 2 (mine is a P3450) so I downloaded a ROM from the page indicated, I tried to update the shipped ROM using romupdateutility, but as soon as it got to 2% it failed saying that the vender ID is invalid.
Now, I don't seem to be able to update it with anything - not even the unbrick ROM. What a shame I almost go there.....
xumiking said:
I tried to update the shipped ROM using romupdateutility, but as soon as it got to 2% it failed saying that the vender ID is invalid.
Click to expand...
Click to collapse
You put the shipped ROM in the same folder with RUU??? Why??? You don't need to do that...
You only need to double click on shipped ROM and the installation process begins...
@sbettencourt,
actually yes what I did was to click on the update directly.
I downloaded the file RUU_Elfin_DOPODASIA_WWE_2.20.707.1R_4.1.13.51_03.07.90_RED_Ship_Reduced.exe and executed that directly.
However, now, even this one is stopping at 2%.
Is there any hope, or have I destroyed the phone?
Thanks.
If you can't flash the Shipped ROM, you have now to try the Gold Card... Follow the steps in that Gold Card thread...
Hello everyone,
I finally managed to revive the device, by flashing it with a 'correct' shipped ROM, which did not give any errors on updating. Big thanks for all your support - you are the best!
As this starts to get addictive, and because I am now running a ROM version which dates to 12/11/2007 (2.27.468.1B WWE), what are the suggestions for upgrading the ROM please? My device is an ELF0100.
Thanks again.
Coool Now try to keep him alive
Very true
I managed to flash it with Onyx Ultimate 4.8 (10/07/2009) and it seems to be performing splendidly.
Thanks for all your help.
Good Job

Categories

Resources