Database Users

RSU 4.21 problem: stuck at boot splash

hi,
i have just downloaded the radio stack from O2 v4.21. I have tried to upgrade through active sync 3.71 it upgraded ok, but when i went to restart the XDA it gets stuck on the boot screen. the one that says test not for resale... and at the bottom right hand corner its says A.30.07 and then locks up.
normally before i tried to upgrade it said A.30.07 the underneath it said 4.20...
anybody know what i need to do to correct it?? i have looked through loads of forum posts and now i'am really confused???
Thanks alot
Zetex :?:

a bit of further info my Bootloader on my xda1 is 5.22
I'am also willing to pay for help i recieve to get my xda up and running again, because without it i really i'am stuck. I don't just use it as i gadget i use for everyday work/pleasure...
Thanks alot
Zetex

can anybody help me????

Hi,
No experts or semi-experts seem to be offering any help. I consider myself a fairly experienced novice so I am not sure how useful (or safe) my advice is. Take care! But here are my observations..........
You say the upgrade went OK? Does this mean you got as far as the message Flash Complete! Press OK to restart your device?
If so, this is encouraging as most of the problems I've located on this forum stopped part way through the upgrade (many at 1%).
Did you follow the instructions accompanying the upgrade to the letter? (ie. kill all running programs, switch off phone etc.)
The 4.21 upgrade is for the PW10A1 model not the PW10B1 (check the back of your xda's case to find out). Not sure how you deal with this one if yours is a PW10B1.
Can you enter bootloader mode? (soft reset with the stylus while holding the power button). If so, this is also good news. Someone with more experience than me could probably tell you what to do next. (Possibly flash a new ROM using the SD card method. Although you upgraded the Radio Stack it may have corrupted or upset your Radio Unit/'ROM'. If you decide to do this, I suggest something based on the v3.17 such as the XDA developers special edition ROM ..... you can always upgrade to WM2003 again later.).
Good Luck!
[/b][/u]

cranny,
Thanks alot for the reply m8, I did try what you have suggested by reloading the 3.17 o2 rom via sd card and now it won't even switch on anymore.
not to worry its gone off to the xda repaire center in Norwich today for repair under warranty.
Thanks for the reply anyway m8
Zetex

Unable to USPL ?

Hello folks,
I'm new here. I don't know much about the technical stuff.
I have HTC3300 (Artemis).
I installed "Gullum's WM6.1 Beta version" in it but It became slow
than I searched here in this xda forum for WM6 and found a WM6 rom for Artemis.
I installed it.
That rom's name is "HTC_P3300_WWE_3.13.405.1_4.1.13.44_02.94.90_Ship_ R".
Now I'm not able to USPL. I have tried 3-4 times. (without SIM and SD Card)
After using USPL utility, on booting it shows:
IPL 3.13.0001
SPL 3.13.0000
GSM 02.94.90
OS 3.13.0.0
SPL is not changing to 1.11.0000. Please HELP me.
How can I unlock it?
I mean how can I succeed to USPL my Artemis?.
I shall be GRATEFUL to YOU

Welcome to the forum.
You have posted two times the same thing, and still didn't said what the problem was...
Can't USPL.. Ok.. But why? Any error? Any something?
Next time just try to don't double post ok?
Cheers

Zecanilis said:
Welcome to the forum.
You have posted two times the same thing, and still didn't said what the problem was...
Can't USPL.. Ok.. But why? Any error? Any something?
Next time just try to don't double post ok?
Cheers
Click to expand...
Click to collapse
First of SORRY for the double post. I thought the same previous post will hide in between the posts in that thread. I won't repeat this in future..
Problem is that I want to upgrade the Radio Rom, so when I use the USPL tool to CID unlock my phone,
after reaching 10%....20%....30%.....40%....50%....60%....70%.....100%, the screen become white and phone gets disconnected from the Active Syn.
Either I have to remove the battery or I have to soft reset to start the phone after "white" screen.
On booting, it still shows SPL 3.13.0000 not showing 1.10.0000.
SPL didn't change to 1.10.0000, is it means that device is still CID locked?
please tell me where I'm mistaking here..
I'm using Vista Ultimate SP1 in my Notebook.

Nobody is there in this forum,
who can help ME ??

Anyway ... thanx to everybody..
I myself found the solution...
New Radio Rom - INSTALLED > 03.34.90 ..
I'll post my feedback about this new RADIO ROM 03.34.90 in the main post by Zecanilis
Thanks "Zecanilis"

could you please let me know the solution?
I got the EXACT same problem
thanks.

Dont worry, the solution was on this post by pvdhelm:
http://forum.xda-developers.com/showthread.php?p=1312109#post1312109

Bhups said:
could you please let me know the solution?
I got the EXACT same problem
thanks.
Click to expand...
Click to collapse
nothing to worrying.. just keep going..
when white screen appeared, i just continued to flash my phone by starting RUU application usually present in the rom folder along with the rom to be flashed..
it showed progress bar in the Computer screen {from 1% .... till 100%}while the PPC screen appeared white during this procedure..
and the flashing process reached to 100%, displaying CONGRATULATIONS on the Computer screen and PPC got restarted by itself with new ROM.
I have done flashing up to 20-25 times by this method.
Phone is WORKING like a CHARM.. NO PROBLEM AT ALL ..

K-JAM Damage

i'm download IPL_SPL_3.08 file and update rom every thing ok but when soft rest my mobile can not open (black screen) no light .like dead
please help me

NEW STYLE said:
i'm download IPL_SPL_3.08 file and update rom every thing ok but when soft rest my mobile can not open (black screen) no light .like dead
please help me
Click to expand...
Click to collapse
Ever occured to you that you are in the wrong forum? Magician and Wizard (K-Jam) are very different devices. So I am sure you'll have a much better luck getting your question answered in Wizard forum.

Peblem with HTC p3400 After upgrade

Dear All
Please help
I did an upgrade and after I tried to urn it on, the mobile just vibrate andnothing else, screen still off , and every thing is off
i tried o start it in boot mode but itis not worked
please help

essa_mohanned said:
Dear All
Please help
I did an upgrade and after I tried to urn it on, the mobile just vibrate andnothing else, screen still off , and every thing is off
i tried o start it in boot mode but itis not worked
please help
Click to expand...
Click to collapse
what u have done plz tell and which rom u have flashed.
read guide and FAQ in upgrading section.

I find this too!
Well,
I am a regular flasher of the ROMs here!
I have faced the issue since some 3 weeks now!
No particular change except tons of ROM changes!
I thought initially, there might be some problem or issue that I have developed thr some mods in the reg-editor.
So I reflashed, and flashed again!
But I see the problem is there and is fairly random!
Though the link I feel is there is with browser use!, whenver I use any browser, its more frequent in occurence.
Anybody has a fix yet?
////
edit: ROMs tried to solve the issue:
Windows REloeded
Genero
Genique
<all latest versions! - Awesome ROMs .. thank you again!>
////
/btw, Windows reloaded ROCKS !! /

Universal qtek 9000 Problem. What im doing wrong?

Hello good friends,
Im from Portugal and i have a qtek 9000 since 2006. In the last days i decide to improve my universal performance...
i try everything to update my qtek since the software is very old ( windows mobile 5 2005)
After a lot of hours searching in this forum, i download a lot of software from all the posible tutorials.
From evk to updatev2, kitchen, etc.
With the kitchen in the last part i always get an error of the extended rom.
With the update, it only appear the nk file.
I try to download one of the radio files, but without sucess and i donw know what to choose
I dont know what to do more, since i use the romupgradeut, but now the qtek only start in the first image where tells the version of rom and hang up, freeze, dont do the all restar.
The only thing that work it is the soft and hard reset. With the bootloader appears usb when connected and serial disconected.
Can you guys help me find a full package including the last windows mobile, the last radio definitions, the extended rom and all i need to upgrade my qtek.
I really dont know what to do more, even the qtek logo image not appear any more.
Sorry for all this questions, but i see in this forum you are my only hope.
Please help me.
Thanks a lot

jus to help us..
could you post the error message?

I try to upgrade the rom with a software download from qtek.nl, but i still dont have good news

Can anyone help me?
I dont know what to do anymore

cybervtec said:
I try to upgrade the rom with a software download from qtek.nl, but i still dont have good news
Click to expand...
Click to collapse
did you read and answer Simon request ?
what are the error message ?
I currently have a qtek9000, and i made my first upgrade late 2006.
I was using XP sp2, activesync, and a software called uniextROM...
Later, I have tried using vista and win7, both requiered installation of USB Mobile Modem Driver and disabling activesync or mobilesync.
so be more precise when you post you issue.

Welcome to forums
have a deep read in my signature link
Most likely you´ll be able to solve the problem.
If not please give us more detailed info so we can help
Read, Search, Respect and Enjoy!

Simon_WM said:
jus to help us..
could you post the error message?
Click to expand...
Click to collapse
Hi Guys,
How can i read the errors? Where can i find it?
Sorry for all the noob questions.
All i can see in the universal is a dead phone without any kind of signal when turned on

cybervtec said:
Hi Guys,
How can i read the errors? Where can i find it?
Sorry for all the noob questions.
All i can see in the universal is a dead phone without any kind of signal when turned on
Click to expand...
Click to collapse
Can you get into the bootloader?
Power + light + Softrest button ?
then connect to your pc and flash

Simon_WM said:
Can you get into the bootloader?
Power + light + Softrest button ?
then connect to your pc and flash
Click to expand...
Click to collapse
Hello Simon,
Yes, i can get in the bootloader. When i connect appears usb.
The problem is i dont know what files i should load.
Can you give me the links to the files i should use. Sorry for the trouble.