replace usb jack: how is it fixed on board? - 8525, TyTN, MDA Vario II, JasJam General

hey how hard is it to replace the usb jack? how is it fixed on the motherboard and how can i get rid of the old one and fix the new one?
i ve seen all the dissambling guides but none showed how to replace the jack

Its soldered to the motherboard. I think you need a microscope to do it and have experience with soldering VERY small joints. Look on ebay under 8525 usb jack and you'll see what it looks like. The solder welds are extremely small. There may be repair places online that do it. Personally I wouldn't attempt it and I have general soldering experience.

hmm ok,
do you know any repair shop? maybe in germany?

No --------sorry.

I have to hold the connection up to get any sound out of it and even then it only comes out on one side, and when I let go there is no sound. I've heard it can be complicated to get fixed does anyone know anything about it? Its a fairly old model.

Related

Wizard replacement parts

Anyone know of a good website to get replacement parts from? The ear piece, and 2 led's dont work. The cable that attaches them has been severed completely and doesnt work.. It looks like it's soldered but I cant see for sure.. I could try resoldering that ribbon but I'd rather see the prices for the replacement piece first.

Needed Button Strip - Anyone have HD2 Parts?

In the process of replacing my lcm, I managed to tear the button flex cable that connects to the mainboard.
I am currently looking for a the button flex replacement. What is the best way of tracking something like this down without going to HTC?
If there is no current seller/merchant available...Um...Is anyone selling an HTC HD2 for parts!?!?!?
Pics included...You can see the button strip, and the little 45 degree angle break on the flex..SUCKS!
I saw the break... Man, that's bad luck...
I hope you find a new button strip. The only other solution would be to solder fine wires from the point I highlighted on the photo. But that is very very very difficult... If you decide to do so until you find a new button strip I would recommend you to let an expert solder it, for example a television-technician. That shouldn't cost you more than a bier for the technician!
Wish you luck!
This just in, I have since purchased a broken hd2 and replaced the button strip. It has a light adhesive and is mounted on two small plastic posts on either end. To loosen the adhesive, just apply gentle heat (blow dryer) and GENTLY peel off. You might come across a stubborn part and want to give it a harsh tug, but you need to methodically peel it up using some sort of flat piece to get from underneath it.
Another torn flex Anyone has spare one or knows where can I get it?
I'm sorry but can't help. I get parts for iPAQs from iPAQ Repairs in the UK. I'm surprised there isn't something similar for HTC parts.
I'm interested in what an 'lcm' is. I've seen it mentioned but with no description.
i need one of these too. i hate htc's policy in not selling parts directly.
This button board should only be like upto $40 usd.
im needing a main board charger soxet broke if price is right ill sell
I have the same problem ....you solved?
where did you buy?
Hi
I got a keypad PCB on eBay... But it was very expensive
Found it http://cgi.ebay.com/Flex-Cable-Keyboard-PCB-HTC-HD2-T8585-HD-II-2-Leo-/320562469094
please how we can solder this wires
please how we can solder this wires
dvdaio said:
please how we can solder this wires
Click to expand...
Click to collapse
You should be a good electronic technician or know a good one. Otherwise I advice you not to try. I am a ordinary technician and I can say that in my case it was very very difficult and even if I tried hard, I wasn't able fix all connections. Only two of my buttons work right now.
How to Replace Button Strip?
Anyone know of a link showing how to replace this strip? Either I can't find key words for a search or there aren't any good videos out there. - thanks
Good to hear I'm not the only one to snap it so easily. Ordered a replacement from e-bay.
Sorry to dig up an old post but, I need that little wire that connects the wifi/bluetooth module to the main board. I replaced the digitizer in my phone and I somehow jacked up one of the ends on the cable. Anyone out there have parts?

[Q] Help! Broken Ribbon Cable

In the middle of disassembling my Legend to replace a bad digitizer, I broke the ribbon cable connecting the power button to the PCB. I haven't reassembled it yet, but I can't see how it's going to work.
img710.imageshack.us/img710/6929/brokenn.jpg
img137.imageshack.us/img137/1346/powerkz.jpg
(Sorry I can't post links because of post count.)
If anyone knows what the best way to repair this would be, I would be most appreciative. Thank you.
EDIT:
It seems this is the piece I need to replace.
tinyurl.com/28a7t9u
tinyurl.com/36yj5tw
Anyone know where I could go about finding one of these? The part number turns up nothing on Google.
I would find a service center and ask there, or I would solder it , it's just two wires....
But be sure you purchase a part with the ribbon cable on it, what I've seen it didn't look like it was there...
Good luck...
Called HTC service center. Unfortunately they don't sell parts direct.
I thought about soldering it, however the ribbon broke so close to the base that I am not sure I would be able to get access to the conductor.
Anyone have a trashed Legend that I could buy for parts?

Hardware Question

I replaced my digitizer and lcd screen but i made a mistake while at it.
I need a new wire but I have no idea what it is for, so I can't search on where to buy it.
It's the longest wire and I think it is the antenna because I can't scan for a wifi or get any data running.
It plugs in to a small circular plug both ways. There are two smaller ones (black and white) right next to the vibrator.
Can anyone help me out???
Indeed, sounds like WiFi antenna.
Just my luck.. Already did a search and I can't find anywhere that sells that piece.
Does anyone know where I can find it?
You tried soldering, if possible? Sometimes full housings on ebay come with pieces like that.
I have never soldered before and I would give it a try if someone told me what to buy... I don't want to mess it up then have to buy a full housing

[Q] broken lcd flex cable connector on motherboard!

I need help with broken lcd flex cable connector on motherboard!
I want to now is another connector fits for Trophy
Nothing?
Nobody knows any solution?
I had this happen on my Touch Pro2, but the cable still worked fine after inserting it. Maybe try a bit of electrical tape on top? I don't know if the facing side on the Trophy connector (the side that is broken has any data carry over or not?)
It's some pretty high level damage to do either way.
I try, but not work.
I hate to say it, your out of luck. :/ Unless you can find someone that can do awesome high level soldering and has access to the parts to replace it... that's it. HTC might repair it at a cost, since the phone isn't under warranty anymore, but you'd have to contact them and ask them if they would and what the price would be.
I buy one with broken LCD and Touchscreen and now I have a working Trophy.
Only thing is to change stock ROM with custom ROM.

Categories

Resources