Related
My XDA 1 just flashes at me when i switch it on. Doesn't load up, i can get the wallaby bootloader up and run tests etc... But that's it....
It won't connect to activesync..." device not recognized"
How can i do it????????PLEASE...
Have you tried hard reset? Insert pin or unscrewed end of stylus in the tiny hole next to the headset connector, push once, leave one minute, push again. If this doesnt work you could try flashing a new rom using sd card method. Did this happen spontaneously or did it happen after flashing new rom?
It just happened.
I think the radio stack is corrupt, despite all efforts i can't seem to get an update on there.
Activesync doesn't recognize the xda , so won't connect to it via usb or IR.
The pc will see it as another computer nearby via IR , but i can't look at the contents. It looks like IR can send files to it, but not to specific locations.
It's looking pretty dire
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
nzane said:
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
Click to expand...
Click to collapse
You can flash from the storage card, just rename the .nbh file to TOPAIMG.nbh and put on the root of your storage card, go to bootloader mode and it will flash.
Your cable can be bad and still charge. I would try a different cable.
Also try deleteing the partnership in Active Sync and try to reestablish it.
I assume you hard reset after you flashed the ROM.
I do not think its a ROM issue.
Ok thanks for your reply.
I did what you sad but when I loaded the TOPAIMG.nbh in the bootloader, it came up with an error and freezes on: Loading ...
When I restarted it It Only shows:
___________________________
RUUNBH
TOPA100 32M
SPL-1.83.000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW
TP MFG DATA
510,547 180,883
177,209 842,207
844,844 Calibrated
Upgrade ROM code Error
Please try again
_______________________________
And then he goes to the white screen with the blue letters saying: Loading...
(I waited many times, one time for 2 hours but nothing happend).
When I put out my SD-card and the battery and connect the phone with the USB (my pc still don't see recognize anything) it will boot to the exact same screen as I typed here above but then he stays at that one.
I can't do anything, already tried to hard reset him but that also didn't work.
It feels like im pretty screwed..
Please help!
Maybe you have a problem with the mini USB.
Happen to me with Touch HD.
If so take it to a reppair shop.
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
nzane said:
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
Click to expand...
Click to collapse
I am concerned that you screen shot shows SPL 1.83.00, but you have flashed Shadowline's ROM.
It should say SPL: 1.83.00Olinex which would mean you have HSPL installed which is absolutely required to flash a custom ROM.
Did you have that ROM operational and just couldn't sync, or has the device not worked since you flashed this ROM?
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
nzane said:
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
Click to expand...
Click to collapse
I guess my point was if you had Shadowlines ROM, you were already HSPL'd, no need to do again.
Hard reset the phone and try to install ROM from SD.
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
nzane said:
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
Click to expand...
Click to collapse
Just some points;
Make sure the .nbh file is named excatly TOPAIMG.nbh paying attention to the case of the letters.
When you attempt to go into Bootloader, Holding Voume Down and Power buttons at the same time when phone is off, what screen appears?
[Q] my handset doesn´t recognize sd apps
I had the same problem as well, so I deactivated and reactivated the SD card from the phone, actually I cant take out the sd with the turned on phone. It worked once, but it happened again so i tried to the same but know the deactivate function in settings doesnt worked. Now i dont know what to do. if anyone could help me i would be very thankful.
My handset is a xperia x10 with 2.1 generic flashed bb 2.1.54, and 2.2 wolbreak gingerbread rom.
eiffeltom said:
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Click to expand...
Click to collapse
i have a tmobile wing and i have vista so i wanted to update my phone with a knew rom version....so i installed windows mobile device center 6.1 ...but it would not sync ,i uninsalled it then reinstalled it no go....so im wondering how can i hard spl my phone without my pc ....and install a rom ...now i tried my wifes touch pro 2 on the windows mobile device center and it works but my wing wont ....anyone ran into this problem or has a solution ...i read a few threads saying hard reset but that did not work
Do you intend to flash with the flash center using the USB cable or have you considered using an SD card to flash your ROM?
If you are using USB to flash have you tried putting your phone into bootloader mode? While pressing the camera button, press the soft reset button below the volume control with the stylus and continue to hold the camera button until the tri colored screen pops up. When it does, look in the bottom left ( if I recall correctly ) to see if it recognizes the USB connection. It will say USB in that bottom left spot if it is connected and you are ready to flash. Ideally you want to be connected via Active sync but it is possible to flash from the bootloader screen.
Consider flashing via SD card. There are many different threads on this and it really is a very simple process. I hear it is also better for flashing because if you unplug the USB cable during a flash you can brick your phone. Just an idea.
Good luck.
yes i would like to flash from wmdc if possible....ill try the bootloader mode first
i just tried it the bars come up and it says usb in the corner ...but wmdc would not recognise it ...is there some settings on the wing i need to do to get it to sync
1milenia said:
i just tried it the bars come up and it says usb in the corner ...but wmdc would not recognise it ...is there some settings on the wing i need to do to get it to sync
Click to expand...
Click to collapse
To flash from the boot loader screen you just need to go through the steps in the flash center. I never looked to see if my computer recognized the phone while plugged in; I just assumed it did not because active sync was not running. You should be able to initiate the flash through flash center and as you go through the steps it should recognize which rom you have loaded and it should read the rom you plan to install (which should be placed in the RUU folder within the flash center). I personally had to do this process about two flashes ago and can verify that it worked for me without having to "be connected" as far as Window's was concerned.
My advice, just go through the steps in flash center and you should see some progress. Good luck.
i went through the process it tells me nothing is connected then i have to exit
1milenia said:
i went through the process it tells me nothing is connected then i have to exit
Click to expand...
Click to collapse
I would then go through the steps to format a 2gb or less MicroSD card and place the ROM file in the root directory and renaming it HERAIMG. From what I hear, this is a safer way to flash anyway so this should be your method whenever possible. There are many threads describing this process. The hardest part for me was to find a way to properly format my card in my computer. My best advice if you have a Dell or another laptop with an SD slot built it, would be to use another port to plug into. I tried for days to find a way or a program to format my MicroSD card in the built in SD slot but no matter what I did, it would not work. Finally, after much frustration, I tried a usb card reader and managed to successfully format the MicroSD on the first try and have been flashing with this method ever since. Hopefully this is all it takes to get you back up and running again. Good luck once again; I'll have my fingers crossed.
HELLO
Please my phone htc p4350 just going to boot loader and not read an activ sync please iwant soulation
Guys, I have a P3300 that has a non-functioning USB connector. Charging works fine, but it will not sync over USB at all. The device is not detected at all. Even in the bootloader screen, when the USB cable is plugged in, it DOES NOT say "USB" in the bottom corner. Basically, the data functionality of the USB port is fried.
I had used USPL to flash a cooked ROM onto the device, and when the USB port worked, it all went fine. Now, with the USB port not working, I can only flash a stock ROM onto the phone using the memory card method. If I try to flash anything other than the stock ROM, it says "certificate invalid" and won't do it.
I read somewhere that there might be a method of doing the CID unlock by using the memory card, since the phone will not communicate with the computer via USB to use USPL the normal way. Can someone instruct me on how to do that? I have the USPL files on my computer, and simply renaming the .nbh file in order to try to use the memory card method won't work.
Can someone help me figure out how to use USPL or otherwise CID unlock the phone over some method other than USB to the computer? Thanks,
Well you can use activesync over BT, right? That might just do teh trick + SD card flash after it reboots to bootloader.
I might be wrong, it's just a thought
I tried that, but the USPL loader kills Activesync right at the start. So once the phone soft-reboots into the white screen and AS is killed, there is no more BT connection. So the USPL loader fails with an error of not being able to connect.
Can anyone else help?
I faced the same problem. White screen. I removed SIM and SDCARD. So I can flash normally.
Wiki: Artemis SD Card Flashing
Try reading the Wiki on Artemis SD Card Flashing
Those having questions on flashing (i.e. updating) their HTC Artemis could try following these steps 1) Backup e.g. PIM Backup 2) disable standby and hibernation then remove SIM & SDHC cards 3) if necessary then cid unlock 4) recommend hard reset or update to the latest official build 5) if necessary Update SPL to latest 1.11.cmon 6) flash new rom then hard reset 7) put in SIM & SDHC cards and enjoy the result of the hard work by the developer
Also check out this thread Uspl/rom upgrade/tips&tricks
Cheers
Tom
hello. I exactly have the same problem like the thread poster. my mini usb only charges and cant connect data to any pc. its probably broken as common with using the O2 artemis on a car phone charger and starting the car while the phone is still sitted and charging.
MY QUESTION: does "Artemis SD Card Flashing" doesnt require the USPL? since its CID locked?
Hey, small problem here. I was charging my HD2 earlier today with no problems at all, I flashed the 1.72 stock ROM back onto my phone, and it seemed to be charging fine for a small while after that. But now, after I tried charging my phone, it doesn't seem to recognise there's a USB connection at all. The LED at the speaker-grille isn't doing anything, and the the phone tells me it isn't connected by USB when it's plugged into a computer.
I tried a tonne of things, checked the cable and switched it, soft-reset it, took the battery out, hard reset it, and even blown inside the socket to try and get rid of anything that might be blocking it, but it just isn't showing it's plugged in AT ALL any more... and now the battery is dead, so I can't do anything with it now to try and help it. :/
The only sign I have that the phone realises it has any sort of USB connection, is when I tried to hard reset the device, (I used the hold volUp+volDown+Power method) and it shows the message 'press volUp to hard reset,' usually when I do this, pressing volume up doesn't do anything when the phone is connected by USB for some weird reason - and I have to disconnect USB for the phone to hard reset. I figured this wouldn't happen if the phone doesn't realise it has a USB connection, but when the cable was plugged in, it still wouldn't hard reset until I took it out. So it shows there must be some way the phone knows it's connected.
I'm running the WWE 1.72 ROM with radio 2.10. 50.08_2 if it helps.
Any suggestions?
*Bump*
Sorry for the bump, but it would really help if anyone could help explain this.
I think a bit of trial and error would be best here to establish whats at fault.
phone, cable, or usb port.
-try plugging into a different usb port
-try a different cable (if you have one)
appologies if you have tried these allready.
Tried another cable again just incase, still nothing though. My iPods connected via that USB port I tried using, and that's working fine, so it doesn't seem like that's it, either...
Hi:
I'm having a similar problem. I had plugged in a new retractable usb cable, and when I did, the phone shut off. I rebooted, and tried my original cable, but the phone doesn't charge or sync. I've also tried hard/soft reset, wall charger, usb charger, and none of that seems to work.
Any suggestions?
Thanks.
No idea if this is related or not but my USB connection stopped working after I got the "bttrayce.exe is not a valid pocket pc application" problem (Thanks TomTom! ) so it would appear the USB port has some weird dependencies!
Fixed it by renaming the windows\btsdkce30.dll file (added "[temp]" to the name just in case!) and soft-resetting.
Might be worth a try?
r u using activsync or windows mobile centre ???
USB Issue
I've got exactly the same issue, running HyperROM 3.01.405.T1 and Radio 2.06.51.07.
Suddenly USB isn't working, tried various cables and I suspect it's a software issue somewhere.
Charging isn't a problem at the moment, I have a charging station (ebay from Hong Kong) so I can access the phone and try and resovle this.
I'm going to go back to the stock rom (I assume I'll find that somewhere on XDA) and upddate the Radio version and see if that sorts it.
If anyone has worked out what's casuing this generally let me know as I can imagine this will take a lot of trial and error to solve!
Thanks
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
My problem solved
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
fpcraveiro said:
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
Click to expand...
Click to collapse
Uninstall TomTom and the problem goes away.
You can download versions on TomTom Navigator 7 with the Bluetooth files removed - like * HERE *
I don't have an OS installed...
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
MrHellas said:
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
Click to expand...
Click to collapse
I you were trying to flash Android you just need to flash Clock Work Mod (CWM) and then place the .zip file for the Android ROM on your SD card and use CWM to flash the Android ROM. It is links to Youtube videos in the OP of the thread showing you how to flash CWM and the ROM.
Are you could flash back to Win MO through USB and bootloader or SD card and bootloaderr.. If you go for USB and bootloader make sure you see USB in the white bar of bootloader befor tryng to flash the ROM. Also thew SD card metrhod will remove HSPL if you use a Official and not a custom ROM.
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
MrHellas said:
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
Click to expand...
Click to collapse
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
T-Macgnolia said:
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
Click to expand...
Click to collapse
How do I get back the loader without booting up? Obviously haven't been able to copy the rar files. Could this be why my GPS and other functions could not be working properly?
imanh said:
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
Click to expand...
Click to collapse
Thanks this sorted my problem!
imanh said:
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
Click to expand...
Click to collapse
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
mcdoc said:
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Click to expand...
Click to collapse
Your USB drivers for the defualt bootloader (multicolor screen) seem to be working fine, so no you do not have a hardware problem. You might want to uninstall Windows Mobile Device Center or Active Sync, which ever one your computer uses. Then re install it. Also go to device manager in your comtrol panel while you have hour HD2 booted up and connected via USB and clck on update drivers for hour phone, it should be listed in device manager.
kushki said:
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
Click to expand...
Click to collapse
When you say your Serial in boorloader does not change to USB this tells me you are having driver issues or hardware issues with your micro USB port on your HD2. My bet is it is just driver issues. I sugest you uninstall and rei nstall Wimdows Mobile Device Center or Active Sync which ever one your computer uses. These programs contain the USB drivers for the HD2 and MAGLDR partialy relies on those drivers to. So maybe that will solve your problem.