Pairing BT devices . - XPERIA X1 General

Hy
Im a litle bit frustated , trying to pair a HCB-120 car kit.
First time I did worked as all manuals explain detailled , but , I got an error after introducing password, I didnĀ“t pay much atention because devide worked as expected .
Problem begins when I delete configuration on BT and try to pair it again .
Never work again last step , pasword intro never apears , looks like device link properly , but after a few seconds car kit goes out .
I have tryed to change my phone name to force it to a new pair process , but all is the same .
Any help ?
THx

Soft reset your x1 before you start.
On your X1 turn on bluetooth and make sure it is set to visible.
Set up your bluetooth device so that it can be found (put it in pairing mode).
Use your x1 to set up a new pairing - enter password if needed.
After your device has been paired with your x1, check to see that your x1 will automatically connect when in range (not sure what the settings are at the moment).
Once a pairing has been set up it shouldn't need to be changed.

Thx but after following instructions I get same resolts.
I will try with a fresh rom

Related

universal and bluetooth connection

So far I have been unable to syncronise using bluetooth. I could do it without much sweat win pda2k (ba), but not with jasjar (universal) so far. Any other owner managed to figure out how to do it? Cheers.
Got it working no problem at all. In fact I managed this before I managed to get it working with USB.
I used the same method that one would use for any WM2003 device.
Set PDA to discoverable on JASJAR
Look for BT devices from PC
Select the JASJAR
Select BT serial port
Find out the COM port of this serial port. Note it down.
Fire up activesync
Change the connection settings to look on the com port you noted down.
On JASJAR got to BT settings
Add a BT device
Select your PC
Select Activesync partner
Go to activesync
Select synch via BT from the menu
i will try again
i prefer the wm2003 wizard to wm2005, i will see maybe i missed something. thanks for clear instructions
still problem with bluetooth
Well I still have been unable to get the bluetooth working for the syncing. I follow the instructions in the booklet and help files, + what I just been told, but there are two issues,
the serial port is for outgoing from the PC, so that could not be used.
In the Com ports tabs two com ports get assigned one for incoming and one for outgoing, with the BA, we use the incoming which we feed into the Activesync, and it works then.
If I do that and create a sync relationship on the pda, there is the option of assigning outgoing port from pda, however when relationship is created only the incoming serial is showing up...
anyways, i have no problem using bluetooth on BA, and could not get it to work on jasjar/htc univ.
Doesnt matter I dont mind using the cable, but dishing the equivalent of US$1400 for a pda whose wizards dont work properly is a bit of an anteclimax.
And talking about ergonomics, the virtual keyboard has the annoying tendency to cover what u are going to write, so u dont see what u are writing...
They also removed the Avantgo utility from the IE, but I got it back by installing the one for winCE and upgrading over...
So for now, I will keep working on my BA (pda2k) as I dont want to waste my time working around bugs, until these get ironed out.
Greetings
Nabil H
I hope all these bugs will be fixed after the official launch
working at last
i managed to get the bluetooth syncing, the secret
1. hard reset,
2. recognise device on pc side
3. create activesync partnership on pda side
4. check incoming com port on pc side
5. feed that to activesync on pc side
6. check activesync partnership from pda side with pc
7. pda will pick up on partnership serial connection as being activesync
8. incoming and outgoing com ports ready to be used on pda side
9. choose outgoing com port on pda same as incoming com port on pc
10. connection established syncing starts...
All this without starting using the usb cable (so different from BA method)...
hope it helps others...
probs... again
Now after setting up and synicng with bluetooth I used the usb link to sync, and it complained about an error. I had to remove the bluetooth setup, and it is still complaining, I give up
I guess the famous russian saying is very wise: "Better is the enemy of the good"
Nabil H out
bluetooth, usb link and wifi
No wonder bluetooth was turned off by default in this jasjar shipment. I believe the following are bugs:
1. U can set up activesync over bluetooth initially after a hard reset.
2. If you then set it up after over a usb link, u lose the bluetooth setting, and can only sync over bluetooth after a hard reset again!
3. If u set up bluetooth, u get difficulties with wifi not connecting (on my system I can only get that back by disabling my wifi connection then enabling it again, dont ask me why this is so, i do not have the foggest clue)
4. When ur wifi is worknig u start having problems with bluetooth connections.
5. Even with a bluetooth sync working, u cannot browse folders on ur jasjar device from another device, as this service does not seem to be implemented.
This does not look very good for users who have multiple/various network connections...
So a patch is already needed for these connectivity issues...
Developers, look into this please...
Greetings
Nabil H out
wifi and bluetooth - solved
I finally managed, after some sweat to get:
. Wifi and bluetooth working together
. Two pda's BA and Universal using wifi simultaneously.
However what cannot be done is:
. Using two pda's with activesync simultaneously, this is a limitation of MS Activesync.
Greetings
Nabil H
PS On club imate website there is now a faq fro JASRAR (HTC Univ).
wifi and bluetooth - solved
Nabil,
can you post what you did to get this working.
thanks.
--------------------------------------------------------------------------------
I finally managed, after some sweat to get:
. Wifi and bluetooth working together
. Two pda's BA and Universal using wifi simultaneously.
However what cannot be done is:
. Using two pda's with activesync simultaneously, this is a limitation of MS Activesync.
Greetings
Nabil H
PS On club imate website there is now a faq fro JASRAR (HTC Univ).

TyTN with bluetoooth headset: voice speed dial wont work

PROFS OF THE XDA-WORLD, PLEASE HEEEEEEEEEEEEEEEEELP!
i have my htc tytn since 2 weeks. i connected my Samsung WEP-150 bluetooth headset (worked previously with Samsung tels, and qtek 9100). Now the issue is: after hard reset the headset works properly: push-beep-i say the name-he says the name and calls. And this is the last time it works until the next hard reset. The issu comes up with Nokia BH-200 headset too. The unit opens the audio gateway (can hear the noice), but closes it immediately, so i cant hear the beep, and say the name into the headset. If the unit is in my pocket, i cant say the name loud enough!
What i allready tried:
-upgrade to ext 106
-upgrade to jasjam 1.20...
-and with the original (ext 105) firmware the bttoggle prog.
The bttoggle (i red about it here) is a funny prog. Everybody wants to listen music on his unit, but i just wanted to use as designed. If i run the bttoggle 2 times (first is audio gateway on, second switches back to voice speed dial), the stuff works till the next softreset (or sometimes it loses the setup in suspend mode too).
Anyway, i think this is not good so.
PLESE HELP ME!!!
thx
peterke
PS: one more question: why is a com port in the headset profile there? is it useful? the dealer told me to switch it of, and only use the handsfree port.
sorry bout ur head set
I bought the same one that was already used but i cant activate it cuz i dont have the code,are they all the same code?were can i get the code to activate it ,do you know?i would appreciate the help if you have it!I know you said it sucks but i would still like to try it!

Active Sync and Bluetooth: Disconnected after some minutes.

hello,
everytime when i connect my device to active sync via bluetooth, it gets connected, syncs but then some minutes later the device gets disconnected.
is this a feature to save the battery or a bug? how can i disable it?
and i have an other question: with the standard AKU2 the prophet's bluetooth driver has less functions than my old nokia phone. is there any way to update the bluetooth-driver without flashing the whole rom?
bluetooth disconnting
hi its me pevicks bluetooth disconnects after some time
nothing is preset so . i too have the same problem . i later found out that its not due to time . its due to the load u pass through the device. if u send big or heavy files it ill get disconnected. try and say if it is true .and make sure u are under the range of BT . and if u want to cover long distance via bluetooth buy a 3.0v device .if ur phone is ideal also some files are been transfered if u have any program that works behind..............

bluetooth Handsfree not auto reconnect at WM6

hi every body specially , Dear rom koockers
i have been tried all WM6 ROMs released here , all have this big problem in connection wuth blue tooth handsfree devices: they connect briefly and good interconnection meanwhile the handsfree is in the range (about 10 meters) after putting out the handsfree device more than 3 minutes out of the device distance range and then go back to distance range the connection cant recognized automatically between handset and handsfree (if u go out of range and back as soon the connection initialized but if u stay more than 2-3 minutes and then turn back to range no chance to auto reconnect of handsfree bluetooth and u must press the key on handsfree device to initialize connection althought no need to reenter passkey) , this problem ic common at all the coocked WM6 roms but not in the WM5 roms.
this the only (but very BIG and dissappointing) problem of useful and pretty looking WM6 roms would u anybody please solve yhis big problem.
****i tried all registry and software tricks not solved and only turning back to the WM5 solved this problem*****

[Q] Problem pairing n9006 with renault radiosat

Greetings to all forum users .
I apologize for my bad English .
I am the owner of the N9006 .
I have two problem.
1) If I insert the headphone jack , you only hear one side , and if you do not push it all the way down you will hear from both sides. Can you give me some possible solution before taking it in for service ?
2) But in fact I am writing to another much more serious issue .
I have big problems with bluetooth connection between the terminal and the renault Radiosat ( issue already addressed and never resolved in several forums , including foreigners ) . We omit all the tests , studies and readings of pounds of post . However, I believe to have found the problem.
Given that as I do the first pairing - phone carkit everything works (except the contact management) . And it works if I do not bluettoth off the phone , in the sense that if I leave the car and after we return, the paring is automatic.
The pains begin if I turn off the bluetooth on the phone.
If reactivated , do not connect more and I have to redo the whole procedua pairing .
With total disbelief , I discovered that whenever deactivated and reactivated the phone bluetooth , changes its mac addres .
But the mac adress is not fixed, because it depends on the vendor and the hardware ?
How is this possible? How can I change it and make it permanent ?
This explains why not connect a second time. The machine reads a different mac adress ......

Categories

Resources