Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

After upgrare Stucked at boot screen

Artemis and PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
i tried to upgrade my o2 arte200,i waited 30min. but installation frozen.
i did reset but after reset my phone stucked at bootscreen
IPL : 1.25.0001
SPL: 1.25.0000
GSM : 02.67.90
OS : 1.28.0.0
Please help... i tried hard reset and soft reset ... but no way...
when i plug usb cable activeSync dont recognise phone

same problem here,
help needed in advance

Active sync is usable only with Windows booted device. If Windows isn't able to boot, you must enter into bootloader, plug usb cable and then start rom flashing.

hi sir
i entered bootloader screen,connected usb cable ... (i can connect using mtty)
i run the software "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE"
but gets an error message " cant connect to the phone"
WHY ???

finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????

CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
is a Rom for the Wizard not for the Artemis.
You need the original ROM so you have to search for the O2 ARTE200 ROM. The language of the ROM has to be correct as well.

how do you get the phone into the bootloader?

Tha said:
how do you get the phone into the bootloader?
Click to expand...
Click to collapse
Press and hold the record button and then do a reset.

no it doesn't work
My DOPOD was in the same trouble. I got the same vender ID error. Does anyone know where to get the original DOPOD P800 chinese ROM?

The same problem has I also.
My ROM upgrade ended bad. Test of installing of different ( I have already them probably 12) the INVALID ends VENDOR ID
I it can not now to remove CID nor to find out what it has it CID HTC__001 does not it fit. T - MOB 005 does not it fit.
I look for original romu from Dngaard ( DK)
Someone knows what CID maybe it is in HTC 3300. I have HTC P3300 is distributed would to Dangaard.
Where from him download
I greet
Irek ( POLAND)

im having the same problem on the o2 orbit ( need a orignal rom

upgrading
hai i am stuck in o2 orbit flashing in bootloader mode
help needed urgent

i got it working after i found the original german rom...loaded the orbit into the bootloader screen with 3 colors....plugged in the usb cable..then ran the german rom, after a few mins it reset and the orbit loaded up...after that i followed these steps to get it into english
http://forum.xda-developers.com/showthread.php?t=290241
flashed it with the tmobileuk 1.13 shipped file. everything is ok now.

cbprod said:
i got it working after i found the original german rom....
Click to expand...
Click to collapse
Where do you find the orginal rom?
Please help us!

send me a pm with your email, i'll send it to you

got mine back from the repair center friday.
no cost at all, fixed

route said:
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
Click to expand...
Click to collapse
could you tell me how did you manage to conect your phone? i have the same problem and i can't get my palm recognized by windows...

you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).

xister said:
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
Click to expand...
Click to collapse
is that the o2 UK rom or the German one

hw6915 help!!

I have made my worst error in my life i think... i was trying to update my rom.... but ...
First my HW6915 with a great hp logo wich says "hp invent, vG.39" and in the top something that says "serial" or "usb" when i plug it up.
I try to fix it with i know .
But now ....black ......with nothing
I have reading all the things you talked and having no idea .
i asked someones help..How can i do!
Do i have something to do ??? Has my ipaq chances ?...
PLEASE HELP ME !!!!

still in trouble with your 6915?

wikidorg said:
still in trouble with your 6915?
Click to expand...
Click to collapse
Yes ,it's still in trouble. what can i do.....

can you make a hard reset?? by pressing simultaneously the five buttons : power button, camera button from left side, green "send" button and red "end" button from keypad and the soft-reset button (using your stylus)... ? (i was tired first time i wrote the procedure, my mistake!)
or, perhaps, enter bootloader by pressing simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset (using your stylus)
if ok, you'll have that screen again, showing vG.39 on bottom, and "serial" or "usb" on top...

Helo !
You can try hard reset, bat not in the way wikidork was told you. You must press POWER button, GREEN dial button, RED stop button together and then pres RESET with stylus. If this wont work then try with bootloader mode like wikidork told you. When you are in bootloader mode try to upgrade with French ROM and then with ENGLISH one like i did. This must work.
Best regards,
Drahtman

NO use.

Always black

that means you accidentaly broke your hp's bootloader... unless you have some knowledge on dealing with JTAG-related operations, it seems useless to try other software miracles...best advice : sell the rest of your device or buy a similar hp with broken display from e-bay, in order to change the mainboard... or send the dead ipaq to some professional service...
regards

Pls Where is french rom?

i hope recuperate hw6915... pls help
i have hw6915 and now appears on screen SERIAL and vG.39. I tried write rom with ruu.exe and .... "code 203: UPDATE IS INCOMPATIBLE
This version of the Update Utility is not compatible with yor iPaq.. bla..bla.. bla
This Update: Model ID: hp iPAQ69(0,5)
Language: ALL
Your Device: ModelID: hp iPAQ hw6915
Language: WWE"
anybody can help me?
my email is [email protected]

Hi,
Here is the link of French rom:
http://forum.xda-developers.com/showthread.php?t=337975
Try with Orange one.
Best regards,
Drahtman

hw6915 german to spanish
Hi. Please I need your help because I don't now if my PDA is broken, I tried to change the language German to Spanish the realized steps have been the following. - hw6915_up_2_spanish_flasher
when the installation process finish (I'm not sure if I disconnects the PDA from the base before finish the process because now on the screen appears the following.
Serial + hp + vG.39 but change when I conect it to the computer to : USB + hp + vG.39
I don't now what is the next step to load spanish rom I have the archive but how I have to do it because when I conect the Hw6915to de computer to charge the rom after one minute appears error.Pls what I can do but the thing is that now the PDA is inoprative NO GERMAN - NO SPANISH.
please can you help me to repair or finish the process.Thank you very much in advance for your cooperation. and sorry for my bad english
[email protected]

I think I killed my elf0100, Help ?

I don't mind paying someone who would help me revive this device
The device is a HTC ELF0100 locked to movistar spain
I tried to unlock it with the following files
Cert_SPCS.cab
EnableRapi.cab
Touch_Unlock.zip
I got a 8 digit code that would not work.
I then tried unlocking with ELF_USPL-v1.zip. This is where things went wrong. The device did not upgrade ok.
Now the device just shows the operator logo for a few seconds then switches off.
It sometimes goes into booloader mode. And I could gather the following information
IPL 2.20.0002
SPL 1.11.0000
Please help, I just want to revive this device now. I don't care about unlocking !

Anyone with suggestions ? I have no idea what to do next

Same happened to my phone. i had to contact HTC support. thay sorted this out for me. i think you should do the same.. but dont tell them that you tried unlocking, otherwise they wont help you..
Spain Español +34-914-146-588 Mon - Fri 9 am - 5:30 pm

Thanks bro for their contact details. Normally they are very unco-operative with phones that have been tampered with or if they know you tried to unlock it. Also we are near the weekend and I need this phone working before monday.
Now I really do not want to unlock it, just wanna revive it.
I cannot even go a hard reset now

[REF]Recover / Revive your dead / bricked HTC ELF or ELFIN[ONLINE]
silhouette said:
I don't mind paying someone who would help me revive this device
The device is a HTC ELF0100 locked to movistar spain
I tried to unlock it with the following files
Cert_SPCS.cab
EnableRapi.cab
Touch_Unlock.zip
I got a 8 digit code that would not work.
I then tried unlocking with ELF_USPL-v1.zip. This is where things went wrong. The device did not upgrade ok.
Now the device just shows the operator logo for a few seconds then switches off.
It sometimes goes into booloader mode. And I could gather the following information
IPL 2.20.0002
SPL 1.11.0000
Please help, I just want to revive this device now. I don't care about unlocking !
Click to expand...
Click to collapse
This should help.

Ok bro, I'll try this and before that let me just thank you !

you have flashed wrong spl and ipl, let me know you want an english rom or spanish rom. you will have to flash original rom, in order to revive your device, is it with 64 mb RAM or 128 MB ram, then i will let you know what to do.

gagandeepbains said:
you have flashed wrong spl and ipl, let me know you want an english rom or spanish rom. you will have to flash original rom, in order to revive your device, is it with 64 mb RAM or 128 MB ram, then i will let you know what to do.
Click to expand...
Click to collapse
Thanks bro. I need a spanish rom. I really do not know if it's 64 or 128 ram. Do I have to open the device?

go to following forum- http://forum.xda-developers.com/showthread.php?t=379034 and download following rom--RUU_Elfin_DOPODASIA_WWE_2.20.707.1B_4.1.13.51_03.0 7.90_BLUE_Ship_Reduced.exe, connect device to computer via usb cable and press camera button and power button together, a tricolor bootloader will appear on device screen, now run the downloaded rom. This is english rom, you can search any original spanish rom if available in above post and flash it afterwards, but initially bring your device to life with the rom i have mentioned above.

Ok, gagandeepbains. I'll be back with the results. Thanks bro!

gagandeepbains said:
go to following forum- http://forum.xda-developers.com/showthread.php?t=379034 and download following rom--RUU_Elfin_DOPODASIA_WWE_2.20.707.1B_4.1.13.51_03.0 7.90_BLUE_Ship_Reduced.exe, connect device to computer via usb cable and press camera button and power button together, a tricolor bootloader will appear on device screen, now run the downloaded rom. This is english rom, you can search any original spanish rom if available in above post and flash it afterwards, but initially bring your device to life with the rom i have mentioned above.
Click to expand...
Click to collapse
Thanks bro that worked like a charm! Any idea how I get the spanish language back? Now the device is in english
I regret not reading before doing what I did and going through the entire mess.
Thanks again mate

you can try ROM 2.20.214.1 ESN (Windows Mobile 6.1 - SO CE 19214 - Build 19214 aku 1.0.4) or any other you like at -- http://www.htcspain.com/foro-f30/guia-de-roms-para-htc-equot-touch-sequot-t4576.html , but you must cid unlock device before flashing.

Thanks for the quick reply bro. I tried Cert_SPCS.cab, EnableRapi.cab, and Touch_Unlock.zip files which gave me an incorrect code.
Any other way to unlock this? Any way to change language if I cannot unlock the device ?

go to following page http://forum.xda-developers.com/showthread.php?t=408637, and download file-USPL_2.28.0000.zip . Unzip this file in a folder on desktop and replace RUU_Signed.nbh file in RUU folder with that of downloaded rom's RUU_Signed.nbh file. install enable_rapi and cert_spc files already with you to device memory, soft reset device and remove its sim card and memory card. Run the elf-uspl.exe file extracted in folder on your desktop after connecting the powered on device to computer, and follow on screen instructions.

Hey I followed your instructions, I got errors on the first two occassions. Process completed successfully the third time. The handset is still locked with language english.
Rom version : 2.20.707 1B WWE
Rom date : 10/02/07
Radio version : 03.07.90
Protocol : 4.1.13.51
Extrom version : 2.20.707.101
Any way to change back to spanish ?
Thanks

I have a problem with my HP hw6915

In my HP was problem with RADIO. I want repair this problem and i write "P10504_BT_HP_Radio_Patch". On screen displaied HP logo and vG. 39 (light is off) and computer show error 605. Now when i want write any ROM to my devince computer show this error again. I was trying write Orange rom (hw6915_up_2_french(Orange)_flasher) and english ROM (G3 DEVICE ONLY hw6915-1.21uk) but this not help me. Now when i power on my HP on screen is HP logo and vG. 39(bootloader) again. Sorry for my bad english and i think that you help me
In MMTY.exe i do "task 28 55aa" end now when i power on my HP LCD is black but when i do bootloader mode i see "serial" and vG 3.9 (my phone is g3 or g4?) When i writing new rom in bootloader mode computer show error;/ Maybe i have CID lock ?? How i unlock my phon ?? Please help me In this site: "http://forum.xda-developers.com/showthread.php?t=471942" is manual but i need rom G4 and i have G3 only ;/ )

helllo
just add me to your yahoo messenger list :cata_cata_cs. i cand help you restore the hp..but unfortunately i can't make it work as a phone. only pda and gps

hw6915 german to spanish problems
Hi. Please . I tried to change the language German to Spanish after. I was start the process with . - hw6915_up_2_spanish_flasher
when the installation process finish (I'm not sure if I disconnects the PDA from the base before finish the process because now on the screen appears the following.
Serial + hp + vG.39 but change when I conect it to the computer to : USB + hp + vG.39
I don't now what is the next step or what I can do but the thing is that now the PDA is inoprative. NO GERMAN - NO SPANISH
please can you help me to repair or finish the process.Thank you very very very much in advance for your cooperation. and sorry for my bad english
[email protected]