hi,
i have an spv m700 with dopod rom loaded. the problem is that default 'phone' app hangs and doesn't exit with 'End Key' button. this happens only when i'm on a call for long enough for the backlight to go off, the call ends when i press the end button but the phone application doesn't exit to the today screen and when i press the ok key to exit, the today screen appears but with a stuck task bar saying 'Phone' instead of 'Start'. the windows key doesn't work either and i have to turn off the display and turn it back on to refresh the whole today screen and task bar.
please help.
thanks.
Related
I WAS WONDERING HOW I COULD REINSTALL WINDOWS ON MY DEVICE AS I CANT SWITCH IT ON. IN FACT I CAN SWITCH IT ON BUT WHEN IT TRYIES TO ENTER THE WINDOWS SHOWS A WHITE SCREEN ONLY AND DOESNT START PROPERLY AND THEN A BLACK SCREEN AGAIN.
PLEASE TELL ME WHAT TO DO.
For god sakes, stop typing in capitals.
Hold down the Comm+Voice buttons while pressing the reset button. Then release the reset button. Keep your fingers on the Comm+Voice button until it says "Push send to format"... then press the bottom left button on the front of the device (i.e. the green telephone button). It will say FAT format complete then it will reboot. Wait about 2 minutes for it to repopulate the device's ROM.
There, you have a factory-fresh device.
I'm running Black 3.01, and the only way I can bring the device out of STANDY is with the power button. My KeyLock is set to "Lock buttons if device is locked." The device is NOT locked, just in standby, and the only button that can get it to wake up is a quick-push of the Power-Button.
I thought there was an app that said you could push ANY button to bring it out, but I can't find that on WM6 Black 3.01.
Thanks!
I asked this same question long ago with no real answer, i hate the small power button and its just to hard to find... If the power button could be relocated to the PTT that would make this phone awesome...
mitchg said:
I'm running Black 3.01, and the only way I can bring the device out of STANDY is with the power button. My KeyLock is set to "Lock buttons if device is locked." The device is NOT locked, just in standby, and the only button that can get it to wake up is a quick-push of the Power-Button.
I thought there was an app that said you could push ANY button to bring it out, but I can't find that on WM6 Black 3.01.
Thanks!
Click to expand...
Click to collapse
Start>Settings>System>Key Lock
Select "Do not lock buttons"
Hello.
My solution to this problem is to use MortSaver. It can be configured:
one press on (a specified) button sends the phone to standby
two presses on (a specified) button bring the phone back
one press on (a specified) button show the time, missed calls, mms/sms, battery and phone signal
I've assigned it to the upper right (Internet Explorer) button and it does the job well.
Best regards!
jZ
Not sure if this helps, but a friend of mine broke his power button, and now wakes his device up by ejecting and re-inseting his memory card.
On my Mogul, a long press of the red phone button turns the phone on and off, and of course because the red phone button is raised it is often pressed by accident and turns off the phone.
I tried AEBPlus to de-assign the button, but both the new assignment works AND the phone still turns off. The author thinks that perhaps phone on/off is done "in the driver".
I'd rather handle this with software than by grinding off the button or trying every case on the market
Does anybody have a software tool or Registry hack that might help?
P.S. I'm also in the market for a replacement phone app that lets me place the speakerphone button on the same page as the digits (i.e. not skin, an actual re-arrangement)
I saw this over at sprintmogul.net , havnt tried it but it sounds like it might help. Good Luck
Source Hai-zi
Code:
HOW TO: Permanently Disable Flight Mode
You must have a registry editor installed on the PPC. I used PHM RegEdit
Go to the registry and change the following key:
HKEY_CURRENT_USER -> ControlPanel -> PhoneExtendFunction -> CDMA
Change FlightModeSwitchByPnHEndKey to 0
This will prevent the phone from going into Flight Mode if you accidentally press the End Call button for too long.
Note that Flight Mode can still be used by tapping the signal strength meter. (I wish I could disable that too)
p.s. if you find that phone app let me know
Cornan said:
On my Mogul, a long press of the red phone button turns the phone on and off, and of course because the red phone button is raised it is often pressed by accident and turns off the phone.
I tried AEBPlus to de-assign the button, but both the new assignment works AND the phone still turns off. The author thinks that perhaps phone on/off is done "in the driver".
I'd rather handle this with software than by grinding off the button or trying every case on the market
Does anybody have a software tool or Registry hack that might help?
P.S. I'm also in the market for a replacement phone app that lets me place the speakerphone button on the same page as the digits (i.e. not skin, an actual re-arrangement)
Click to expand...
Click to collapse
Better to have your pocket press the red button and turn off the phone than press the green button and redial your last call all the time. Stop both from happening by Start>Settings>Today>Items and making sure Device Lock is checked; then click "Device Unlocked" on the Today screen, which locks input, before putting the phone away. You will have to click "Unlock" to re-enable the buttons and screen; however the green phone button will still work to answer incoming calls while locked.
Also, were you aware that holding the green phone button down for about three seconds while on a call toggles the speakerphone on/off?
Hi guys,
When i want to call someone with the green button (call button), when i press it then the volume goes one down and the camera opens.
This is not all the time. But sometimes it happens and it verry anoing when u want to call someone.
So when i press the green button it doesnt call but opens the camera.
I did not install any software, but was changing some settings in su2. But i set it back.
Another thing is, when i press up whit the middel button it inserts #* instead going up.
how can i set these things right, instead hard reset
Hi
Does anyone knows how to tweak the registry in WM6.1 and when you end the call ( by press the BT or the end button) automaticaly close the dial screen and go to the Home screen??
Thanks, Michalis
michalisg said:
Hi
Does anyone knows how to tweak the registry in WM6.1 and when you end the call ( by press the BT or the end button) automaticaly close the dial screen and go to the Home screen??
Thanks, Michalis
Click to expand...
Click to collapse
use with iContact v1.03
I simply press the hard red button.. it closes the dial screen...
Hope this is what you are looking for
Ciao
Fred
The problem is that the ipaqs 900 series they have problem losing the audio if you use BT headset and end the call. you have to press twice the red button to go to the home screen fast, or you will loose the audio... thats strange but they will fix it in the next firmware.
Now i want something tweak or registry settings that after the end of the call to go straight away to the home screen otherwise i have to end the call from my BT and then IF i have the phone close to push the red button to go to the home screen. before losing the audio