ok, i got a att 8525 with herm100 ipl-1.03 & spl-1.11, currently its not booting up because of a failed attempt at installing crc r13.3, i can get it to the tri-color screen, but i can't get it to connect to activesync, it is getting recognized by the other ruu rom flashers but after it goes to 1%, the phone reboots, and i can't get past that even with tryin to flash a factory rom.
there anyway to unbrick my phone?! i've tried a couple of the ways i've found from searching but none seem to work, my pc is running vista but i also have xp on vmware if needed.
well i finally got the factory rom flashed, and now its working again!, i don't know how it happened, it just......happened.
Related
I flashed some rom on here a while back. The wife has the wiz and I have the herald. Anyhow, she was having problems so I figured I'd flash the stock 2.26 tmo rom back on her mda. I ran through the update utility and it crashed at about 7x %. Now it is stuck in a bootloader reboot loop...Anyone have any suggestions?? I need to get her phone working again so any help is appreciated. By the way, its a G3 device.
Thanks
Kevin
Just reflash the t-mobile stock ROM again, as simple as that. Most of the time when you have a failed flash you get the bootloader every time you boot. Make sure you don't connect the sync cable until after you're in the bootloader and when you do connect it it says USB at the bottom and you should be good to flash from there.
I have a Dopod 818pro that was flashed with the wrong ROM and now all I get to is the DOPOD splash screen. I can get to the TRI color screen by pushing the camera and power button.
I have tried hard reset but seems the OS is missing from the phone.
I have the original ROM for my phone on my PC but can not use active sync as the phone does not go further than the SPLASH screen.
How can I reload my original ROM using the SD card.
Any help would be appreciated.
Thanks
Canada59
use the tricolor screen even though active sync doesnt see it it still flashes but u need to use the flash upgrade wizard and not the cli interface one
Worked for me but i cant sae it will work 100%
Where do I find the flash upgrade wizard?
When I plug usb in, i get usb on the white band in the color screen
Tried to run the update using RUU and get ERROR 260
Thanks for your help in this
Yeah RUU same thing i was meaning that one cause theres another that uses cli but its a bit dodgy
RUU Wizard should work it never detected ma G4 but it flashed it anyway i was well chuffed cause i thought i had bricked it
I just tryed the app without the phone connected and it gave me error 260 so maybe try different cable or pc cause i had a issue with xp not detecting my phone and i had to reinstall xp just to get active sync to work properly
The main problem is that I had a bad flash, now I can not get pass bootloader screen, PC does not see device, active sync says not connected. there must be a method for loading the NK.ntf file from sd
Not came across anything like that as the SD card driver would be loaded at boot with the OS and in your case theres no OS booting it would be hard to sae it can be done but i bet someone will prove me wrong lol
Good Luck mate ill keep an eye out for anything like that though
Thanks for the help....phone is useless at the moment......
Hi,
I'd like to flash my HTC Touch HD, but everytime i run HSPLWrapper_Blackstone_156OliNex, the process sits on 0% and i get 262 UPDATE ERROR.
I searched the forums, tried soft and hard reset, reinstalling ActiveSync, differrent cables, usb ports. I tried to use official HTC ROM, to find out if the problem is in the connection, but it worked on the first try.
I would really appreciate any idea how to fix this.
Thanks
Have you tried USPL?
have you tried putting the phone in bootloader manually? to do that, hold down power and volume down at thesame time. then connect the usb cable.
Thank you for fast response.
@lohpsch:
No, I haven't. I'll try it now.
@accountabc:
I have already tried it. It behaved the same - stucked at 0% and 262 error
edit:
USPL worked.
Thank you!
how abaut if phone only logo
i have that problem
Have you tried upgrading your Blackstone on a different PC that runs Windows XP?
i think you must run SSPL-manual-touchHD.exe on your device to get three color mode before you flashing it
My friend asked me to try recovering his T-mobile DE Hero, it was bricked while my friend was trying to root it
I tried to flash official rom, but RUU gets error 170...
This what appears on screen when device is on:
error 170... thats the usb connection error right?
this could be because the drivers are not installed properly.
read this thread, then try again
http://forum.xda-developers.com/showthread.php?t=647353
Although error 170 is indeed USB error, (with windows 7 normally) the nasty looking Icon at the bottom of the screen does not look good, never seen that before
Let us know how you get on please
I had the same error with mine.
I ended up in installing a custom ROM, since NOTHING would work. No drivers no nothing. It just refused to read the phone.
I installed VillainROM 12, it has OS 2.1 so it's working perfectly
I had the same problem, but I was trying to flash my German G2 using an HTC Official RUU. I've been able to flash the recovery rom using fastboot and then boot it, but that's where my progress has ended. I'm about to flash VillainROM12.0.0-Full and see what happens. I'll let you know.
EDIT: VillainROM12 installed via AmonRa Recovery menu, but rebooting takes me right back to the RUU screen with an Xed-out EPROM
Nothing helped
I tried everything You said, but device is showing same screen, I also tried using SD card method but when I turn Hero on (while holding Vol-) same screen appears
Does anyone have any other idea what to do?
Its looking like a problem with a radio (drivers etc). Try to update it through recovery if u can enter there.
You can see in my first post the only screen where I can enter...
Well.. This icon with a "chip" probably say a SPL or Radio of phone is just f***ed up.. :/ You can enter to fastboot so drivers of graphics and other modules are in good condition..
wheeeler i think u should find a .zip with a official SPL and radio and update it through recovery like u did it with Villain ROM
I got some idea but I think u tried it before.
iwanrakic U can connect to phone via SDK?
Try this command. It should update it.
C:\sdk\tools>fastboot flash radio radio.img
Of course u need image of official radio.
What driver does Windows report installed when you plug it into your PC in that mode?
Hi there, I've been reading the forum for about a week trying to find a fix for my deceased orbit xda.
Problem started when the phone started crashing, the screen was going white and needed re-starting. Eventually it failed to load and froze at the blue screen with the red writing!
so I started reading and tried soft and hard re-booting to no avail.
I have managed to get the phone into bootloader and connected a USB
it recognises the usb and installs as a mobile device on my laptop but here's where it gets tricky. I dunno alot about phone's and am struggling to understand some of the processes. I have tried booting off the SD card but it said invalid certificate (i used the artiemg.nhb file from rapidshare)
I have all the original paperwork and cd's for the phone but dont know what or how to flash a ROM.
what do I need and more important how do I do it without all the tech talk.
Its a WM5 phone - thanks
EDIT - Just to clarify, have just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Update, I managed yesterday to get the phone to boot from the SD card and indeed it flashed it and WM5 is back up and running, the new problem is its network locked (to O2 i presume). I was using this phone on orange previously without an issue????
any Idea's other than paying imei check?
...
danv6saxo said:
just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Click to expand...
Click to collapse
what link was it?
what error did you have?