iPAQ hw6965 Stock at HP Boot Screen. Help!!! - Sable

I recently did a Radio Stack upgrade for my hw6965. After that it doesn't receive or send SMS. I tried to fix it using several Radio Fix on this site and ended up with a device stock at the HP boot screen and "NO GSM".
My Bootloader Version is: G39 and my ROM Revision is 1.21APD.00 ENG
Please someone help.
Thank you.

Related

PLEASE help me... i'm desperate!!

Hi...
I upgraded my qtek 9100 from OS version 1.6.7.1 to cingular 1.8.11.1
The problem is that now, the phone doesn't start... the splashscreen appeears, along with... IPL 2.17
SPL 2.21
GSM 02.07.10
OS 1.8.11.1
But doesn't get out from there...
Did a do anything wrong?
PLEASE help me?
Is there any solution or is it bye bye qtek?
maybe you flashed broken or wrong rom.
start your device in bootloader mode (look in wiki how to do this) and then reflash again and if this does not work, get rom from your provider and reflash with this.
...
But my pda starts and it stays in splashscreen... is it repareble anyway?
Yes it should be fixable
Cant understand why you would want a old cingular rom (the cingular is not exactly same hardware as your phone wiza200 vc wiza100!)
You should download an aku2 rom here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
user name xda password xda
Next get into the bootloader screen - turn device off and start with camera button pressed - should be a multicolor screen
Next attach device to pc via usb cable
Flash with above rom and all should be well

After upgrare Stucked at boot screen

Artemis and PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
i tried to upgrade my o2 arte200,i waited 30min. but installation frozen.
i did reset but after reset my phone stucked at bootscreen
IPL : 1.25.0001
SPL: 1.25.0000
GSM : 02.67.90
OS : 1.28.0.0
Please help... i tried hard reset and soft reset ... but no way...
when i plug usb cable activeSync dont recognise phone
same problem here,
help needed in advance
Active sync is usable only with Windows booted device. If Windows isn't able to boot, you must enter into bootloader, plug usb cable and then start rom flashing.
hi sir
i entered bootloader screen,connected usb cable ... (i can connect using mtty)
i run the software "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE"
but gets an error message " cant connect to the phone"
WHY ???
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
is a Rom for the Wizard not for the Artemis.
You need the original ROM so you have to search for the O2 ARTE200 ROM. The language of the ROM has to be correct as well.
how do you get the phone into the bootloader?
Tha said:
how do you get the phone into the bootloader?
Click to expand...
Click to collapse
Press and hold the record button and then do a reset.
no it doesn't work
My DOPOD was in the same trouble. I got the same vender ID error. Does anyone know where to get the original DOPOD P800 chinese ROM?
The same problem has I also.
My ROM upgrade ended bad. Test of installing of different ( I have already them probably 12) the INVALID ends VENDOR ID
I it can not now to remove CID nor to find out what it has it CID HTC__001 does not it fit. T - MOB 005 does not it fit.
I look for original romu from Dngaard ( DK)
Someone knows what CID maybe it is in HTC 3300. I have HTC P3300 is distributed would to Dangaard.
Where from him download
I greet
Irek ( POLAND)
im having the same problem on the o2 orbit ( need a orignal rom
upgrading
hai i am stuck in o2 orbit flashing in bootloader mode
help needed urgent
i got it working after i found the original german rom...loaded the orbit into the bootloader screen with 3 colors....plugged in the usb cable..then ran the german rom, after a few mins it reset and the orbit loaded up...after that i followed these steps to get it into english
http://forum.xda-developers.com/showthread.php?t=290241
flashed it with the tmobileuk 1.13 shipped file. everything is ok now.
cbprod said:
i got it working after i found the original german rom....
Click to expand...
Click to collapse
Where do you find the orginal rom?
Please help us!
send me a pm with your email, i'll send it to you
got mine back from the repair center friday.
no cost at all, fixed
route said:
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
Click to expand...
Click to collapse
could you tell me how did you manage to conect your phone? i have the same problem and i can't get my palm recognized by windows...
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
xister said:
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
Click to expand...
Click to collapse
is that the o2 UK rom or the German one

Urgent help: HTS P3300 stuck up

Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi
You must upgrade :
-Remove SD-Card
-Remove Sim-Card
-USPL
-Upgrade new ROM
thank. i got through to install wm 6.1.
can any one please tell me which is the most stable ROM for 6.1 or 6.5
which one is better for my HTC artemis.
please post link to the ROMs
I'm using two roms :
Shady313-23081R1 : http://forum.xda-developers.com/showthread.php?t=546805
dheewatara-s 23075B1 : http://www.pdamobiz.com/forum/forum_posts.asp?TID=255901&PN=1
same problem..pls help
i have same rom and ratio with u nomi...but my problem still occur...
where do u get the USPL eventually?

Problem after downgrading from wm6.5 back to wm5

I face a strange problem on my dopod 818pro after I donwgrade from wm6.5 back to wm5 NVID rom.It take about 5 minuets to boot back to the windows,even thought i did several time of hard reset it is d same too. Does anyone encounter with this kind of problem before? Please advice.
No sifus can HELP???
Finally I solved d problem liao by upgrading back to wm6.5 Build 23053 WWE bikertibi edition.
Help <urgently needed
Hi everyone,
I tried to upgrade my HTC universal from WM 5 to WM 6.5 using the rom provided by xda v1.01 (128MB rom).
I tried to install the upgrade from my laptop but during the process i noticed a sound indicating that the USB connection was lost. Now all i can see in my phone is 'Serial' at the top and 'v1.01' at the top. Aside that, the phone's literally DEAD.
Is there anything I can do about the phone or is it wasted?
Would appreciate any form of response.
Thanks.

iPAQ rw6815 - Problems with downgrade to WM%

Hello!
I've got a iPAQ rw6815 and after tried a lot of WM6 roms, I need to downgrade to WM5.
Problem is that every procedure on this and other forums, doesn't work.
I tryed directly with patched HpRUU, but it gives me errors (No connection with phone/Bad files, while on bootloader - No Compatible, while running WM&). I flashed HPrw6815WM5miniSD1.12.00.rar, but it stacks on reboot after flashing or on the boot screen when I reset.
I tried with both BL 1.0.1 and 1.0.5, but nothing to do.
Anyone can help me? Thanks!
up up up up up

Categories

Resources