I have a big problem with my Herald. I had tried to change page pool size and after that the Herald is not booting and I stuck on HTC logo screen. How Can I fix it or how can update the HErald ROM with original or differnt ROM ?
Thanks for any idea.
try a hard-reset..keep both soft buttons pushed while reseting...don't let hold of them until the message appears on screen..it should be ok...although you will loose al the personal data from the doc chip
Herald is working
It already wokrks. I had to copy original ROM to 1GB microSD card and flash it from there.
Related
I got trouble - I tell you....
Yesterday, I wanted to update my T-mobile MDA from winmobile 2002 to 2003. I was using "Lumpistefans" -Romkitchen (xda.weblink.net). I choose the rom to be coocked as an "installer exe".
When I performed the update, everything worked fine - for about 30 secs....then brakedown
This message accoured "Can not open COM/USB port...."
from this time on, my mda seems to be toasted!! I can't switch it on , softreset won't work - and after an hardreset the display only shows some black stripes and two blank squares at the top half.
I don't need to mention, that Activesync isn't recognising the mda anymore - saying "uknown usb device - can't connect"
I don't think the Bootloader is working still either - by pressing the on/off button, the bootloader should be activated ..or??!? I never tried that before.
I read the thread "rom flashing is dangerous" but didn't get any helpfull info on my case.
I need Help...getting quiet despered!!
THANKS for alls Help , Hints and comments!!!!!
ciao
mark
here is how you enter the bootloader
http://xda-developers.com/bootloader/
ok thanks - the bootloader is still working ... can i now just flash it with a rom using my sd card?
yes just plug in the sdcard of min 64MB into your sdcard writer/reader and use xdatools to flash the nbf or nb1 file to the card
and put in the sdcard and go back into the bootloader
I am sorry, this has probably been covered before but I have search but can't find it at the moment, my Qtek 1010 is stuck at the boot up screen where it shows Qtek.
I have upgraded the rom using the SD Card and still you reset the phone and it just sits at the first screen with the Radio and rom versions at the bottom of the screen......
Please help.
Thanks
Went flashing process fine? Checksum OK?
Had you done the hard reset?
Have you tried reflashing it again?
Stefan
I reloaded Rom from SD card and reset with the stylus in the little hole in the bottom and same problem, it can't get past the boot screen.
Sorry all, I installed the original rom and everything is fine now.
Thanks for your help, this is the greatest site.
seal said:
I reloaded Rom from SD card and reset with the stylus in the little hole in the bottom and same problem, it can't get past the boot screen.
Click to expand...
Click to collapse
Just short question?
Which little hole? There are two.
One on the side where the earphone connector ias, and one on the other side....
Stefan
Hi LumpiStefan,
I was making a mistake and yes not reseting the phone with the little hole, I have an XDA Mini and I forgot all about the other little hole that you unwind the stylus for.
Only problem is it doesn't fix it, The only rom I can get to work on it is the HTC Qtek v3.18.04wwe, it is the only rom that will boot into the operating system, I have tried other roms from this site but none of them will boot, I did get the 2003se rom to work but the phone part didn't work, it was like there was no radio, there was no signal graph up the top, so I tried to install the 2003se rom over the top of the working Qtek rom and same problem, it can't boot.
I really want 2003 on the phone so I can put Voice command on it.
Any help would be great. Thanks
I have downloaded nearly every rom and no 2003 rom will work, they all just after I hardreset it want go past the boot screen. So I load the old Qtek rom back on every time by SD Card and everytime it boots up fine, I don't understand, why does the Qtek rom work but no other.......
Any help please...Please...
hello, i tried to upload new rom but something goes wrong, computer hang and now my pharos only shows pharos logo and versions ONBL, SPL, GSM, OS. I can put it in bootloader mode, but unfortunatly my spl is 1.11.0001 and everytime i try to upload any rom which is posted on this forum i got error: invalid vendor id or error: file is corrupted. Is there any way to unbrick it? any way to upload hardspl to this device now? I dont have any dump or other things.
have you tried with hard reset?
press and hold softkey left + softkey right + power button
Yes, i tried. Hard reset went ok. Format FAT ok. Restart and the still the same.
the only way is to flash an official rom
have you tried this?
Yes, i tried both. On both after 1% devide reset and update utility gives ERROR[294]: INVALID VENDER ID.
my friend have the same problem,he buy pharos with software crashed for repair for himself...
it was dutch edition and any hard spl or official rom doesn't work,
pharos shows boot screen and then he stucks
how can we wake him up?
you can try flashing from the sd card... but this is a difficult problem ... hard spl should work and also shipped rom should work (for the guy with dutch Pharos try the dutch shipped rom)!
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
hard reset
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
do hard reset
i had done hard reset also
Try to bootup without the SD card (and may be SIM), I had this problem with my Vox, the SD Card was corrupted. After formatting the SD Card, everythig became normal.
Best of Luck
Same problem
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says Setup complete, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos (from Portugal)
matosmatos said:
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says congratulations, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos
Click to expand...
Click to collapse
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
for ur info @matosmatos
hi
as per the numbers quoted by u urs is a old gene so falsh roms for old gene only this is just for ur info
goodluck
matosmatos said:
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
Click to expand...
Click to collapse
@smb_do
hi
assuming ur phone is just dead ie just blank screen do this
1.power off the phone remove batter and press the power button 3 secs
2.put batter back in to the phone
3.Press camera button and then power on at the same time u will get tricolor
used usb and Flash new ROM
or press camera button and do soft reset using stylus this will also give u the tricolor use USB and flash new ROM
goodluck
smb_do said:
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
Click to expand...
Click to collapse
thasnffffffffff
Im so so saaaad
I try avery thing hard reset , now roms every time it accept the now rom and whine it restsrts again tha same problem it stop at
ONPL 1.07.0000
SPL 1.07.oref
GSM 02.79.90
OS 1.9.1.1
please help me send me at
ahmedrefaat82/hotmaill.com
gene hanges at start up page onyl (after rom Upgade)
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
satishgosavi said:
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
Click to expand...
Click to collapse
Not likely, try a hard reset and see if your issue is solved
Addicted2xda said:
Not likely, try a hard reset and see if your issue is solved
Click to expand...
Click to collapse
I had tried that also but not able to recover I had to burn the ROM again .
I am scared now to soft reset my gene. Never know when it will get hanged again. (pls note that it does not hang on every soft reset).
I liked the new ROM (6.1 pro Sumeet) so much. It is fast and have left enough room to add/execute other applications. I have read so many good comments about the ROM. I do not want to change it to any other version.
Please.. please try to get some solution.
Thanks in advance.
regards
Satish
It Worked
Thanxxxxxxxx
Hi,
I'm kind of new around here.
My problem is as follows:
- TyTN running PaysRom for about 9 months
- Started to get very sluggish
- Unable to get signal
When i booted my HTC the 'R' and 'G' that appear on screen and used to have values in front of it now display 'none'.
So, I connected it to my PC, 'activesynced' it and tryed to install a new ROM, hoping it would solve the problem.
But the new ROM wasn't installed sucessfully and now all I got is a brick.
I can't even connect it to ActiveSync since it's not recognized.
Is there any solution to my problem?
TIA,
hype
Can you get to the Bootloader?
Yes..
By pressing the Ok+Power+Reset on the bottom button, I see the 'RGB'+white thingie, that I believe is the bootloader..
What SPL do you have? Is it Hard SPL V7(2.10)?
If it is, use the sd card method to install a new ROM.
remember to backup your card 1st.
1. Format 2Gb or less sd card FAT32. Copy .nbh file of the ROM you want onto it and rename to hermimg.nbh .
2. Insert card into Hermes and reset into bootloader.
3. If all things have been done right, follow the prompts....
If the radio ROM has died, I'd suggest trying to flash the Shipped Stock ROM 1st and see if that actually fixes the problem with the blank values on R & G. WM06 upgrade of shipped carrier ROM should also work.
Cheers...
Tks for your response.
I tryed the SD Card method already, with no sucess.
The red stripe shows as follows:
Code:
HERM200
IPL-1.04
HERM200
SPL-2.03
Everytime I tryed on another ROM I always perfomed it using SafeSPL.
Since I don't have 2.1, what can I do?
Tks for all ur help.
What happens when you try and flash a ROM over?
Do you get any kind of error?
You need to find the SHIPPED STOCK ROM. WM06 upgrade should be OK as the CID should match.
Put Hermes into bootloader and connect to PC after unticking "Allow USB Connections" in Activesyncs settings on the PC.
Run the RUU_Wrapper.exe file of the SHIPPED STOCK ROM. ven though activesync won't etect it, the flash file should. Follow the prompts.
Good luck as this seems to be the only way to fix this.
Good Luck...
You might be able to flash a Stock WM5 ROM using the SD Card method. Worked for me when I had SPL 2.03. In fact that's the only ROM it would let me flash over when mine bricked.