phone blanks on rom 1.19 WWE - Touch HD General

I am on rom 1.19 WWE
Whenever I start a phone call, the screen blanks (becomes black) but the phone call can continue. I have to press the power button twice to "resuscitate" my device.
Is this normal? If not are there any steps to solve it?
Of course I set the power settings to keep the device ON at least for 5 minutes both on batteries and on charger.
Backlight question:
I cannot see the backlight settings, which in my former device (kaiser) where under power settings area. Is this normal?
Thanks and waiting
Saulo866

it's normal. with the screen blacked-out (off) you won't accidentally launch a program

dear Cortez
Thanks for your message
1.
But why this (screen blanking) never happened on my former Kaiser, Athena, Dopod, Tytn, etc?
2.
Is it possible to cancel this function? In fact I wish to monitor the call details, timing, or even do some other actions, while calling, like activate conference mode, etc.
How to disable this so-called "proximity-feature" ?
Thanks
Saulo866

Ehm push the on/off button. There is also a tweak for it. Use search or read the topics here

http://montecristoff.webs.com/hdtweak.htm

Related

XDA 2 always on handsfree (speaker on)

Quote this FAQ from myxda.com :
Q. Is it possible to activate the loudspeaker on my xda before choosing a telephone number? Is it possible to permanently turn the loudspeaker on loud, so i do not have to press the green button?
A. There is a way for doing this. The only disadvantage: after a soft-reset this setting is not activated anymore and must be readjusted. Dial any number, for example the Voicemail Box, so that nobody is disturbed by a phone call. Then disconnect and tip onto the signal symbol in the title bar. Tip onto the disconnect telephone button and then immediately press the green button (accept telephone call) keeping it pressed until the note appears: The loudspeaker is activated. The telephone then disconnects, without establishing a connection. The information that the loudspeaker is activated remains. The next step is turning on the telephone. The loudspeaker is turned on instantly with each dialled number. However, you can always turn the loudspeaker on or off by pressing the green button a little longer BEFORE dialling.
I've tried it and there is no response, even I can not get first step (Tip on the disconnect button ). May be this FAQ is only for XDA I ...
Has anybody tried it on an XDA II ?
Has anybody a way to permanently activate loudspeaker on XDA II ?
Yes, I've tried it, it works.
But sometimes could be difficult to activate due to some lag or slow response time for taps ... Once activated, the screen will look like this:
Can yo please explain it step by step ?
I've tried a lot of times, withou results. Thanks
ok, i found this easier:
- Turn on flight mode.
- Press green button for a few seconds until it says "Speakerphone is on". (Don't worry, as you're on flight mode, no call is made)
- Now, turn off flight mode to use the phone and have the speakerphone always on.
Enjoy.
No way !!
Turn On fligth mode.
--Press green Button while in TODAY opens Phone Screen
---Press green button while in PHONE screen shows Buuble "The phone is currently off. Dou you want to turn Wireless on?
I have ROM 1.60.00 WWE
-- Radio Version 1.10.00
You'll have to PRESS DOWN AND HOLD the green button for about 2 seconds. Not just one click.
Of course I did it
Have you been able to activate speakerphone during a call before?
The procedure is the same, press and hold down the Green button should activate, except that this is done when flightmode is on.
It's strange why your unit doesn't behave the same? Try hold down longer perhaps..
@chriswo
sorry for OT, but PLEEEEASSSE let me know the name of that software you're using for the today screen. i've been desperately looking for something like this for ages now.
thanks
regards ize|man
if you mean
chriswo's screenshot
then do you mean the signal strength
or ?
if you're talking about the launcher, it's called cLaunch, it's free.
Yes I can activate it during a call, and as I like it (it works 'sufficient' for me as a hands free for the car) is because I wanted to have it always activated.
May be there is some installed software. Will try to uninstall what is not essential. Can you post your rom & radio versions ?
boyz boyz you're fast as lightning
i just updated the screenshot. pls reload this page.
and YES it's cLaunch i just googled and it seems to be what i need (BIG buttons on the today screen)
thanks a lot
regards ize|man
Alrught, if you find it difficult to activate Speakerphone while on flight mode. try this:
On PHONE display, turn on flight mode and immediately PRESS AND HOLD DOWN the green button. Don't let it go completely on flight mode, so you got to do it while the radio was shutting down.
try that and let us know.
OK, this one WORKED without problem.
Now I have a 'perfect' and 'cheap' handsfree for my car.
THANK YOU very much !!!
Chriswo?
Where did you get that signalstrenght today plug in from ? looks really good
That's HudsonMobile PhoneDashboard.
Anyone notice if you cancel the speakerphone, then enable your bluetooth headset and make a call, the headset stays connected even after you end the call?
I don't know if this really is an advantage or not, I'll see how much more the battery drains if any.
Also, I notice that after activating the speakerphone "always-on", my ringetone gets almost silent. :?

Stopping accidental clicks/presses from face when on phone?

Anyone know how to stop an accidental clicks or other screen presses from taking place when I've got the phone to my face during a call?
Si.
I use a freeware app called Screen Off, download it here:
http://www.handango.com/PlatformPro...latformId=2&N=96806&productId=125781&R=125781
Basically when I make a call or answer a call I have screen off assigned to a button, so I can then press the button to turn the screen off. To turn the screen back, just press the power on button.\
Hope this helps,
Or maybe you could simply turn PDA off with a single power button press...and when you're finished simply turn it on. Remember that the radio is always running (unless you hold the power button for 5s).
My screen turns off automatically after about 20 seconds when on a call - haven't set it to do this - in fact can't even find an option - it just seems to be the default setting. The only way to turn it back on is to press the green or red buttons, or just flick the volume control either way - works for me. (O2 XDA Mini s)
S.
Macrinus - thx that works a treat.
That's weird, your screen turning off after 20 seconds, mine turns off as configured in "Turn backlight after..." and "Turn off device...".
macrinus said:
That's weird, your screen turning off after 20 seconds, mine turns off as configured in "Turn backlight after..." and "Turn off device...".
Click to expand...
Click to collapse
Yeah, it is weird - bit annoying, but sensible really to save the power - Perhaps its just the device turning off then, with the phone still running .... comes back to life with a flick of the volume though - touching the screen won't re-activate it. Will have to time it a bit more closely !
S.
Radio on screen off
I too turn the device off when I'm on a call (although I only discovered I could without ending the call this morning). Otherwise, my ear activates the Start menu.
Doh!
if only the backlight is turned off, the screen WILL still react to face contact!
I understand that either the device (less the phone side!) via power button, or the screen must be turned off via an utility.
It may exist, but I know no proggie able to lock the touchscreen without turning it off!
(pitty, my axim X50v can lock the screen without turning it off via a Hw sliding button9

Screen go off on phone call

Hi, everyone. My Tytn when is on a phone call, switch off the screen. I can't find anything like this in the forun (perhaps I don't look for on the right way).
I not find how to disconnect it on the configuaration of my Tytn. Does anybody knows how to get the screen on during a phone call.
The problem is when I'm driving, and on a phone call, lose the screen and my navigator instructions. It's is a problem, cause, I must to switch on the PDA and reconnect the navigator. (the people alwais call on the worst moment , I don't know why?)
Thanks to all.
Start>Settings>System>backlight>Battery Power, then take the tick off the selection "Turn off backlight if device is not used". Do the same under the external power tab.
At the bottom of the screen you should see a MENU option. Click on the Advanced tab then take the tick off the option "Turn off device if not used for ...."
This lot should solve your problem. The downside is you might then start to use more battery power as the device leaves itself in an always on position.
VCheers
WB
wacky.banana has offered some good advice. But IF your problem happens ONLY when a phone call comes in, then I think you might have phoneAlarm installed and configured to do this. pA includes this feature in order to let folks listen and speak, with the phone against their ear, and not fear starting up myriad applications as their ear touches the pressure-sensitive screen.
Just an idea.
-pvs
just press the button
just press the standby button, or any button to turn the screen back on,
id rather have the option to turn the screen back on, rather than having it on all the time especially if i am out and about, and as we all know, battery power on the tytn is a precious commodity :_)

Turning screen back on when SMS comes in?

Hey guys, i noticed that when the screen turns off or goes into stand by and you recieve an SMS/MMS message, the alert sound still comes on, but the screen stays off. Is there a way to change this? It's sort of annoying having to press the top button just to see if a text message comes in. Can it be tweaked in the registry? If so, what would one have to do to change it? I have a registry editor installed on my phone so if anyone has any ideas......go ahead
Standby when phone call received
Hey all,
An extension of the Q above, When I make or receive phone calls, the screen shortly after goes blank, he only way to see the screen again to press the "Call" buttin again, which puts the caller the call on hold. I have to quickly press the "Unhold button again " which is very annoying!
Any ideas any1?
Thanks in Advance...
samir_d said:
Hey all,
An extension of the Q above, When I make or receive phone calls, the screen shortly after goes blank, he only way to see the screen again to press the "Call" buttin again, which puts the caller the call on hold. I have to quickly press the "Unhold button again " which is very annoying!
Any ideas any1?
Thanks in Advance...
Click to expand...
Click to collapse
Use the power on\off button on top instead of pressing the the Dial button.. it was annoying for me too but the power button does it for me and it's better than to keep the screen on during the whole call since all my calls are above five mins
bump...someone has to have some idea what can be done to fix this
If you install HDTweak ( http://forum.xda-developers.com/showthread.php?t=452505 ), you can disable the screen switching off during a call and/or make the device wake up when a new SMS is received. It works for me.
Installing HD tweak and then going to 2.2 will solve your problem.
try the hd tweak or the diamond config both have twaeks to activate the screen when you receive the sms. but be sure to lock the phone for when you have it in your pocket.
NICE!!!! thanks guys for the info, i will try this ASAP when i get home
GAWD I LOVE THIS FORUM
Doesn't work for me
Juggler258 said:
If you install HDTweak ( http://forum.xda-developers.com/showthread.php?t=452505 ), you can disable the screen switching off during a call and/or make the device wake up when a new SMS is received. It works for me.
Click to expand...
Click to collapse
Hi there, I disabled 1.1 and it still does not seem to work for me
However, Enabled 2.1 and that works.
Please help ...
In HDtweak, I have 1.1 disabled, 1.2 Disallow, 1.3 Disabled
The screen doesn't go off during a call. I can always press the power button to turn off/on the screen manually if i want to save battery during a long call (or not attract attention when calling on a dark street!)
Juggler258 said:
In HDtweak, I have 1.1 disabled, 1.2 Disallow, 1.3 Disabled
The screen doesn't go off during a call. I can always press the power button to turn off/on the screen manually if i want to save battery during a long call (or not attract attention when calling on a dark street!)
Click to expand...
Click to collapse
I did the above and it worked...I missed those parts of the instructions
Thanks!

LCD screen blackout while making a call out

Hi,
I had a problem with my Jade where the LCD screen blackout while making a call out, and i need to turn the screen on again pressing the power button.
Can anyone advise me?
Thank you in advance for your advise.
Vincent
No problem, is a normal function
Yup, that's normal behavior. There is a sensor which senses when you have the phone touching your face. It then turns the screen off. You wouldn't want it to activate all kinds of options while rubbing your face.
Thanks a lot! but Garmin problem now..
Hi ralfbonne, Arunia,
Thanks alot for your advise.
I have another problem which is the Garmin Mobile XT 5.00.10W.
Is a cracked version, after i installed S2U2 v1.60, the below error message pops up while half way using the Garmin GPS:
"Read access violation at data address 0xF9C3D650. Program address 0x0016FAF4 in background thread NULL (GfxFieldWindowProc)".
Is this caused by the settings for S2U2?
Besides, sometimes it took too long time to get the satellites signals, can be up to 20mins long!
Could you please kindly advise me too?
Thanks in advance.
Have a nice day.
Vincent
How to keep screen on in call (no blackout): solution
All registry hacks & Advanced Config tricks for keeping the screen on while a call is in progress do not apply to the Jade/3G.
However, there is a solution to overcome this annoying feature:
install Touch InCall Screen Tweak, and set the options "Ignore first screen off" and "Always On" in the options.
Why keep the screen on during call? Your face will just start activating things at random. If you really need it on (maybe using earpiece) you can always press the power button.
It's annoying
I have never accidently pressed anything on the screen while calling.
However, having to press the power button to bring the screen back while calling voicemail has annoyed me many times.
I also believe it is annoying that the screen blacks out. Even when I have the phone facing down and not to my ear, the screen blacks
I need to get it on, so I could use speakerphone. I'm one of those that love using speakerphone, so yea
I will try the InCall cab file.

Categories

Resources