Related
I use the k-jam alot. and after taking the pencil out and back in again it has got so loose now that it usually drops out. any one else hade same problem and how did you resolve it?
I had same problem with my BA. I'm not sure the wizard has same retention tab, but if it does, then this works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Thanks for the tips.
I was just thinking of what to do when i came acroos some bluetac .
I put some blutac in the hole were the stylus goes and pushed the pen in. and it was a miracle !!! The stylus stayes in with a good hold and it comes out clean with no bluetac on it.
whe the bluetac trys to come out it has no room coz the stylus filles the space so it stays in the edges and grips the stulus pen and keeps it from getting loose. .
problem solved !!
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Yes it does.
Easy and simple way of not opening or messing about with k-jam to void warranty.
I mean. you will not viod waranty this way, but will if you open the k-jam
one time around the stylus with some tape works great to.
But what happen if the blutac starts to ware off?
But what happen if the blutac starts to ware off?
Click to expand...
Click to collapse
Then I'll pop the case :shock: , extract the bluetac and do the silicone mod.
I'd be surprised if it does wear off though. It's superb stuff that's saved me a few quid in the past when in rented accomodation - bluetac and tippex to create the illusion of undamaged walls :wink:
Can you please give me a hint what "bluetac" is or means ?
I have dismantled mine, and I can see why this is breaking - see my post regarding the sylus silo.
when the stylus is getting loose, when you are pushing it in do you "feel" it going further forward than it did before?
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
I have taken some photos of how to get the back off, I will post them when I return from my business travel.
Jon
Can you please give me a hint what "bluetac" is or means ?
Click to expand...
Click to collapse
Ignoring my [email protected] spelling (should be "Blutac"), it's this stuff: http://www.paperstone.co.uk/BrowseProductDisplay.aspx?ProductId=17307&CategoryId=579-580-594
I'd be interested in seeing the photos on how to dismantle.
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
Click to expand...
Click to collapse
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
just wrap a piece of tape around the stylus and it fits like a glove again.
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
sunseaker said:
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
Click to expand...
Click to collapse
I've always done this as it does not seem to fully shink other wise... seems Ok so far.
marka2k said:
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
Click to expand...
Click to collapse
Personally I think on the bottom of the phone is daft in the first place... or is this just me ?
Terran
the pics are in the upload folder, called wizardpics.zip - the ftp upload attachment does not seem to be working?
to remove the top half I used a flat knife. It is quite resistant. You can see where the tabs are in the pic.
To remove the back completely, you need to remove the void sticker, and under there is a screw. there is also one opposite.
You will also need to remove the 2 screws at the bottom, one in the stylus channel, and the other on the opposite side.
then use a plastic splitting tool if you have one, or a credit card to work round the case.
you can see in the pics where this comes off.
You then want to re-enforce behind the stylus notch. I used a piece of folded card.
chakra said:
one time around the stylus with some tape works great to.
Click to expand...
Click to collapse
where exactly are you putting the tape which end
i did the blutac thing but might have put too much in cos the grey plastic end i use to pull stylus out just broke!
hi,
this question might not even have anything to do development. i have been using my exec for a year now, and the problem is that the stylus has become quite loose and doesnt stay in the phone securly, have others had similar problems and if yes what's their solution?
thanks
Same problem, but no solution, im sorry
The inner plastik thingy which holds the stylus is somehow.. overused or rubbed off?
I dont think that there is a solution :/
I had the same problem with my old xda exec.
Stuck sellotape around stylus and that did the trick for me.
Simple but effective. Needed to replace sellotape once a month.
I had the same problem. First I have use scotch tape around the stylus which looks ugly therefore I start use few drops of Super glue and making little swell on the stylus
A little lump of blue tac pushed into the socket which holds the stylus in place when I put it in.
ukblokester said:
hi,
this question might not even have anything to do development. i have been using my exec for a year now, and the problem is that the stylus has become quite loose and doesnt stay in the phone securly, have others had similar problems and if yes what's their solution?
thanks
Click to expand...
Click to collapse
Believe me when I say that the best alround solutution is to by a replacement stylus like this one http://www.mobilefun.co.uk/product/8393.htm
I lost my first stylus about six months ago because it was too loose, there is no way this one will fly out. It fits nice and snug.
Mav
mavrik64 said:
Believe me when I say that the best alround solutution is to by a replacement stylus like this one http://www.mobilefun.co.uk/product/8393.htm
I lost my first stylus about six months ago because it was too loose, there is no way this one will fly out. It fits nice and snug.
Click to expand...
Click to collapse
I second this! These stylii fit very securely and are MUCH better than the originals that come with the device. I've had 2 because I accidentally dropped one right on the tip (dropped from my hand, it didn't slip out of the Universal) and both were snug.
bend stylus
i tried to paint my last stylus with nail enamel (color metalic gray), didn't work ...so i decided to bend it a little
it worked for me..
tricky question .. how much bend it ?
well.. i didn't clean enamel from stylus, (im lazy...) while i was trying to bend enamel crack ....that was my scale
The little clip which holds the stylus in on mine broke off completely. I opened the case up and glue the clip back in while padding it out with paper at the same time. Holds the stylus rock solid now, much better than it ever did before.
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
chibahawk said:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
Click to expand...
Click to collapse
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Praygo said:
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Click to expand...
Click to collapse
Yes I could see that the inside casing was a bit rough so sanding should stop the problem - but seriously that's a major issue.
Have you found that it holds the phone well though? Because I'm very upset that my phone fell out of it once already but maybe it was an error on my part and it wasn't secure enough...
I've never had the phone fall out of the body glove case.
i mangled my body glove case.
someone bumped into me and the phone fell out of the case AGAIN.
i ripped it to shreds and left it on the side of the road to rot into plastic hell.
i dont recommend this product.
I returned mine. I had the exact same issues (screen and phone falling out). It also didn't attach properly on the top left corner, it was always bowed out. I don't recommend it either.
Anyone got any else to share?
I was THIS CLOSE ( || ) to buying it. lol
Is there anything out there that's similar to it in design, but better?
returned
When all the way snapped on, mine pushed the top left corner so hard the entire screen would not respond to touch. Returned it.
My friend and i had the same issue. We just took it off messed around with it and put it back and it works fine, SOMETIMES it happens again but we just take it off and put it on.
Since there is not any other case that provides this type of protection we are keeping it. I rather my phone be safe than anything else.
I just ordered mine yesterday so I'm anxiously awaiting its arrival.
What exactly did you have to mod to get it to work? According to my readings, you just need to sand down the edges that connect with the screen right?
I may just buy the case and sand down what was mentioned. I like the design of the case..only one so far I really like.
I've been using one for about two weeks and am very happy with it. Had read about the screen pressure issue on other posts (searching helps folks), and scraped down the top corners before I put it on. Don't need a dremel tool or sandpaper. No problems, fits perfectly. The only warning is that it's a little dicey to take off once it's on -- it really fits snugly.
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Torkrench said:
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Click to expand...
Click to collapse
Could you give us the link for the ebay one please!
http://cgi.ebay.com/NEW-RUBBERIZED-...5|66:2|65:12|39:1|240:1318|301:1|293:1|294:50
That is the one I ordered, and the fit is perfect. The only thing I wish it had was the belt clip insert for the case included. I don't know where to find one, but I mostly keep it in my pocket anyway.
you guys want a good case that protects? check out the monaco aluminum case, it comes with a clear lens on it which I haven't removed but you could if you wanted quick access to the touchscreen. I work in the construction field and have yet to have it fall off my clip. I also dropped my tilt (when I used it) from about 8" off a ladder and it was perfectly fine. The aluminum case for the fuze isn't any more bulky than the body glove case either.
bilbobrian said:
check out the monaco aluminum case
Click to expand...
Click to collapse
I've got one of these as well...and while it does protect the phone very well it will also lower your signal strength. I've had these type cases for the Wizard and Tilt and now the Fuze...whenever I'm in an area where the signal was a little iffy to begin with I WILL either drop the call or be unable to answer with the metal case. So, stay away from the aluminum ones if you go into lower coverage areas (and no...the slots they cut in the back to help improve the signal don't actually help.)
Something I always liked about my Kaiser was having a lanyard attached to it. I did this after dropping it a couple of times due to it slipping out of my hand.
As the HD2 is even more slippery in my fingers and probably more likely to shatter or break on dropping, I was disappointed that there was no lanyard hole.
I contemplated drilling a hole in battery cover but didn't have a drill. So I've duct taped a lanyard onto the back, a la the attached pic.
First I lay the lanyard ring on the back and threaded duct tape through it, locking the lanyard ring to the phone. Then I layered a bit more duct tape on top to give it some strength.
It may look a bit messy and I could have done it neater. At the end of the day it will (hopefully) stop me dropping and breaking a £500 phone which I'm happy about. It's also surprisingly strong and will give an indication before it eventually gives way. Takes about 2 minutes.
Edit: Ugly duct tape method replaced by neater black tape version.
Edit2: Video howto added: http://www.youtube.com/watch?v=yL3owsWT3E4
Disclaimer: If you try this and end up dropping your HD2 anyway, I accept no responsibility!
That could be the worst monstrosity to a HD2 Ive ever seen.
Haha, you may be right. But I don't have a mobile phone to look pretty, I have it to use it and rely on it to be working when I need it, not broken into 100 pieces on the floor.
Here's a neater black tape version. Not sure it will be as strong as the first though.
Biffy said:
Here's a neater black tape version. Not sure it will be as strong as the first though.
Click to expand...
Click to collapse
looks sooo fragile , also u should try take it to a gravire-er if u dont have a drill and make a hole suitable
Job done no messing!
I can't understand why HC didnt add a lanyard bar and at the end of the day your solution will work and probably save your phone one day.
Nice graduated background on your photo and good image quality, what camera did you use?
It's the Panasonic FT1. A little waterproof compact.
Combining duct tape as the first layer and then black tape over for neatness is the best solution so far.
I've also considered super gluing the lanyard into the 3.5mm jack, but know I'd regret doing it straight after!
well, you guys aint the first to do this.
i invented a similar design a few weeks ago, mine used a 1" belt, meaning it can be strapped to your waist any time you like, safe as houses and pretty cool aesthetically
Final version
After a bit of testing, this is the final method I will use.
Some folded black tape under the battery cover. The battery cover adds extra strength to the tape and it looks so much neater than the Duct tape.
to be honest, that is just ugly. sorry.
I also missed such a whole for it, as I also did that with my Kaiser.
Now I sticked to a Silicon/Plastic Combi Case
why dont you get a jelly case or something like that and you can make hole in it. tape will hold fora few days only
I'm going to get a case as well I think. But the tape solution outlined which is partly under the battery case will last a lot longer than a few days.
The tape should only be under any pressure if you're about to drop your HD2, which won't be that often and then the weight isn't that great.
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Mariad said:
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Click to expand...
Click to collapse
Yeah, I agree. The third version looks nice and clean! The only question is: What did you attach the tape to? To the cover itself? Because I wonder how much strength it requires to pull off the cover and if that wouldn't happen if the device falls...
EDIT: I love how you labeled this a "hack"!
I attached the tape to the plastic under the cover, where the sim card is. I'll put a quick video together to illustrate.
I left it hanging by the lanyard last night, for about 7 hours, 7 feet in the air, no probs. It's not intended to be pulled as hard as a regular lanyard loop may be, but for a precaution if the phone slips from your hands. And then it will be fine.
And here's the not very good howto video: http://www.youtube.com/watch?v=yL3owsWT3E4
I dont mean to jinx you or anything, but the piece of string from the lanyard could easily split the single layer of duct tape where it's folded.. that's going to be where the weak point is....especially considering the weight of the HD2. It's not going to matter how many pieces of tape you've got under the batter cover.
Now if you were to have your HD2 on a desk or in your pocket, the temptation of grabbing it by the lanyard will be there... or if someone else decided to yank the lanyard.....
I'd suggest trying that method of attachment on something of a similar weight and shaking it around for a bit to see how the duct tape handles.
Remember... the HD2 screen is thin glass... One drop on a hard surface or if it lands at the wrong angle, it'll be time to order a new one!
I've tested it by pulling far more strongly on the lanyard than it ever would be subjected to in real use. I was able to pull it hard about 20 times before the tape started to give way. By then it was visibly starting to tear away, so you should have a good warning before it breaks. It will perfectly suit my needs anyway and I might try doubling the tape up for more strength next. Also, I think this could be improved by using even stronger tape.
Very good on the last release.
Great idea, man.
I'm going to try, but I've only two left hands....
Pink strap should be nice too ;-)
In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
ah yes, I remember something like this on the original droid... removing it made sliding much easier.
I had the keyboard ones off, didn't even notice the one on the back.
Osin83 said:
In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
Click to expand...
Click to collapse
i didnt notice the one on the back til someone on the forum pointed it out to me...and yes it does make the slider easier but for me its now a little too easy...i kinda wish i never took off that covering i feel the phone open up in my pocket now sometimes its just too smooth....i usually prefer to keep my phone naked but i might have to get a case as i hear some people saying it made their slider a little more stiff
StAlphonso said:
i didnt notice the one on the back til someone on the forum pointed it out to me...and yes it does make the slider easier but for me its now a little too easy...i kinda wish i never took off that covering i feel the phone open up in my pocket now sometimes its just too smooth....i usually prefer to keep my phone naked but i might have to get a case as i hear some people saying it made their slider a little more stiff
Click to expand...
Click to collapse
The case at first made my slider too stiff but after opening and closing it repeatedly it's eased up and is now nice and firm but not too stiff.
ha, I just found it earlier this week. I removed it and the keyboard ones, but my sliding did not seem to change.
Osin83 said:
In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
Click to expand...
Click to collapse
Thanks for the tip.
I thought about removing mine, but I thought it might protect it better if I left them there. But on the other hand, it's so hard to slide open with my case on that I've used the keyboard once, lol.
wardfan220 said:
I thought about removing mine, but I thought it might protect it better if I left them there. But on the other hand, it's so hard to slide open with my case on that I've used the keyboard once, lol.
Click to expand...
Click to collapse
I just took it off on my phone with my case and it has made it easier to slide. You should try it. It's not like it's protecting much. It's the back of the phone that is protected anyways when you don't have it slid open.
The first thing I did when I got my phone was take off this crap.
Sent from my PG06100 using XDA App
I noticed all three bits of plastic strips within a few minutes of playing with the phone. Taking them off definitely made the slider smoother. Especially the big one on the back of the phone screen.
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
wardfan220 said:
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
Click to expand...
Click to collapse
Weird cuz mine and my girlfriends literally do not touch the keyboard, so there is no way for that sound to be made.
wardfan220 said:
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
Click to expand...
Click to collapse
Check and make sure it's not just some gunk in the track or something. The other day when opening and closing my keyboard to loosen up my case it started making this awful grinding noise and I was afraid I'd have to take it back. But after a lot of blowing in the tracks and digging around with a paperclip (Disclaimer: Don't dig around in you phone with a paperclip) whatever it was came out and I was back to smooth, quiet sliding perfection.
jesusice said:
Check and make sure it's not just some gunk in the track or something. The other day when opening and closing my keyboard to loosen up my case it started making this awful grinding noise and I was afraid I'd have to take it back. But after a lot of blowing in the tracks and digging around with a paperclip (Disclaimer: Don't dig around in you phone with a paperclip) whatever it was came out and I was back to smooth, quiet sliding perfection.
Click to expand...
Click to collapse
You know I didn't really look at it much until just now after reading this, thanks for making me look. The sound is the case scraping on the inside back. It started when I took that inside back cover off, kind of wish I hadn't.
If anyone is using a case, I suggest leaving that one on to help silence that knob of the case. At least until it wears down a little.
Sent from my HTC EVO Shift 4G using XDA App.
I've had my phone since the RadioShack early launch day, and those 3 plastic pieces came off about 5 minutes after I left the store.
So fast forward two weeks, and I think the slide out keyboard is too loose. It's been getting worse over time. Flicking through my home screens from left to right causes it to slide out ever so slightly. Very annoying.
I'm wondering if I should have left the plastic on. At least the big one on the back of the screen.
I'm going to order a hard case next week as it looks like a bonus feature is increased resistance on the sliding mechanism.
Never noticed that back plastic but after reading this thread I think I'm going to leave it on. I'm not having an issue with the slide and I would prefer to not have the slide as loose as others are reporting after removing it.
Sent from my PG06100 using XDA App
i left the 'back plastic' on my Mogul all the way until I was through with it about a year ltr...
Really wasn't an issue on the TP or TP2
I intend to do the same with the Shift though... the side plastic pieces on the keyboard will stay until they start peeling off, which will inevitably happen.
I've decided to leave all 3 of them on, more protection .
I removed all 3. It just doesn't feel as good using protection.