In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
ah yes, I remember something like this on the original droid... removing it made sliding much easier.
I had the keyboard ones off, didn't even notice the one on the back.
Osin83 said:
In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
Click to expand...
Click to collapse
i didnt notice the one on the back til someone on the forum pointed it out to me...and yes it does make the slider easier but for me its now a little too easy...i kinda wish i never took off that covering i feel the phone open up in my pocket now sometimes its just too smooth....i usually prefer to keep my phone naked but i might have to get a case as i hear some people saying it made their slider a little more stiff
StAlphonso said:
i didnt notice the one on the back til someone on the forum pointed it out to me...and yes it does make the slider easier but for me its now a little too easy...i kinda wish i never took off that covering i feel the phone open up in my pocket now sometimes its just too smooth....i usually prefer to keep my phone naked but i might have to get a case as i hear some people saying it made their slider a little more stiff
Click to expand...
Click to collapse
The case at first made my slider too stiff but after opening and closing it repeatedly it's eased up and is now nice and firm but not too stiff.
ha, I just found it earlier this week. I removed it and the keyboard ones, but my sliding did not seem to change.
Osin83 said:
In two other threads users have noticed the two small pieces of protective plastic wrap on either side of the keys on the slideout keyboard. They are easily to miss, but easily removabe; with a little tugging they come off in one piece.
However, I'm not sure if anyone has yet noticed the protective plastic wrap on the backside of the LCD. If you slide your keyboard out and turn the phone around, you will notice that the entire backside of the screen surface (where it reads "with Google") is covered in a large sheet of the same plastic. It also removes easily by peeling it back and tugging it out from under the keyboard surface.
Removing all of the plastic from the two articulating surfaces has made the sliding much smother for me.
Click to expand...
Click to collapse
Thanks for the tip.
I thought about removing mine, but I thought it might protect it better if I left them there. But on the other hand, it's so hard to slide open with my case on that I've used the keyboard once, lol.
wardfan220 said:
I thought about removing mine, but I thought it might protect it better if I left them there. But on the other hand, it's so hard to slide open with my case on that I've used the keyboard once, lol.
Click to expand...
Click to collapse
I just took it off on my phone with my case and it has made it easier to slide. You should try it. It's not like it's protecting much. It's the back of the phone that is protected anyways when you don't have it slid open.
The first thing I did when I got my phone was take off this crap.
Sent from my PG06100 using XDA App
I noticed all three bits of plastic strips within a few minutes of playing with the phone. Taking them off definitely made the slider smoother. Especially the big one on the back of the phone screen.
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
wardfan220 said:
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
Click to expand...
Click to collapse
Weird cuz mine and my girlfriends literally do not touch the keyboard, so there is no way for that sound to be made.
wardfan220 said:
I took them off my wife's phone and now you can hear it scrape when it slides open and closed. I'm going to leave mine on so I don't hear that plastic on plastic sound.
Click to expand...
Click to collapse
Check and make sure it's not just some gunk in the track or something. The other day when opening and closing my keyboard to loosen up my case it started making this awful grinding noise and I was afraid I'd have to take it back. But after a lot of blowing in the tracks and digging around with a paperclip (Disclaimer: Don't dig around in you phone with a paperclip) whatever it was came out and I was back to smooth, quiet sliding perfection.
jesusice said:
Check and make sure it's not just some gunk in the track or something. The other day when opening and closing my keyboard to loosen up my case it started making this awful grinding noise and I was afraid I'd have to take it back. But after a lot of blowing in the tracks and digging around with a paperclip (Disclaimer: Don't dig around in you phone with a paperclip) whatever it was came out and I was back to smooth, quiet sliding perfection.
Click to expand...
Click to collapse
You know I didn't really look at it much until just now after reading this, thanks for making me look. The sound is the case scraping on the inside back. It started when I took that inside back cover off, kind of wish I hadn't.
If anyone is using a case, I suggest leaving that one on to help silence that knob of the case. At least until it wears down a little.
Sent from my HTC EVO Shift 4G using XDA App.
I've had my phone since the RadioShack early launch day, and those 3 plastic pieces came off about 5 minutes after I left the store.
So fast forward two weeks, and I think the slide out keyboard is too loose. It's been getting worse over time. Flicking through my home screens from left to right causes it to slide out ever so slightly. Very annoying.
I'm wondering if I should have left the plastic on. At least the big one on the back of the screen.
I'm going to order a hard case next week as it looks like a bonus feature is increased resistance on the sliding mechanism.
Never noticed that back plastic but after reading this thread I think I'm going to leave it on. I'm not having an issue with the slide and I would prefer to not have the slide as loose as others are reporting after removing it.
Sent from my PG06100 using XDA App
i left the 'back plastic' on my Mogul all the way until I was through with it about a year ltr...
Really wasn't an issue on the TP or TP2
I intend to do the same with the Shift though... the side plastic pieces on the keyboard will stay until they start peeling off, which will inevitably happen.
I've decided to leave all 3 of them on, more protection .
I removed all 3. It just doesn't feel as good using protection.
Related
I use the k-jam alot. and after taking the pencil out and back in again it has got so loose now that it usually drops out. any one else hade same problem and how did you resolve it?
I had same problem with my BA. I'm not sure the wizard has same retention tab, but if it does, then this works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Thanks for the tips.
I was just thinking of what to do when i came acroos some bluetac .
I put some blutac in the hole were the stylus goes and pushed the pen in. and it was a miracle !!! The stylus stayes in with a good hold and it comes out clean with no bluetac on it.
whe the bluetac trys to come out it has no room coz the stylus filles the space so it stays in the edges and grips the stulus pen and keeps it from getting loose. .
problem solved !!
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Yes it does.
Easy and simple way of not opening or messing about with k-jam to void warranty.
I mean. you will not viod waranty this way, but will if you open the k-jam
one time around the stylus with some tape works great to.
But what happen if the blutac starts to ware off?
But what happen if the blutac starts to ware off?
Click to expand...
Click to collapse
Then I'll pop the case :shock: , extract the bluetac and do the silicone mod.
I'd be surprised if it does wear off though. It's superb stuff that's saved me a few quid in the past when in rented accomodation - bluetac and tippex to create the illusion of undamaged walls :wink:
Can you please give me a hint what "bluetac" is or means ?
I have dismantled mine, and I can see why this is breaking - see my post regarding the sylus silo.
when the stylus is getting loose, when you are pushing it in do you "feel" it going further forward than it did before?
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
I have taken some photos of how to get the back off, I will post them when I return from my business travel.
Jon
Can you please give me a hint what "bluetac" is or means ?
Click to expand...
Click to collapse
Ignoring my [email protected] spelling (should be "Blutac"), it's this stuff: http://www.paperstone.co.uk/BrowseProductDisplay.aspx?ProductId=17307&CategoryId=579-580-594
I'd be interested in seeing the photos on how to dismantle.
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
Click to expand...
Click to collapse
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
just wrap a piece of tape around the stylus and it fits like a glove again.
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
sunseaker said:
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
Click to expand...
Click to collapse
I've always done this as it does not seem to fully shink other wise... seems Ok so far.
marka2k said:
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
Click to expand...
Click to collapse
Personally I think on the bottom of the phone is daft in the first place... or is this just me ?
Terran
the pics are in the upload folder, called wizardpics.zip - the ftp upload attachment does not seem to be working?
to remove the top half I used a flat knife. It is quite resistant. You can see where the tabs are in the pic.
To remove the back completely, you need to remove the void sticker, and under there is a screw. there is also one opposite.
You will also need to remove the 2 screws at the bottom, one in the stylus channel, and the other on the opposite side.
then use a plastic splitting tool if you have one, or a credit card to work round the case.
you can see in the pics where this comes off.
You then want to re-enforce behind the stylus notch. I used a piece of folded card.
chakra said:
one time around the stylus with some tape works great to.
Click to expand...
Click to collapse
where exactly are you putting the tape which end
i did the blutac thing but might have put too much in cos the grey plastic end i use to pull stylus out just broke!
OK managed to snatch one of the only/few tilts available in my area last Friday and now, after a week of use I've noticed I hate the ATT case I bought: The leather, plastic clip, top-loading case, SUCKS!
I work in an ER so speed, quality, ease of use is paramount. My major problem with this case is that 1. I press buttons trying to pull it out and 2. the belt clip is not centered well so when I try to orient it horizontally on my scrubs the opening end tips downward toward the floor.
SO, I've been searching around the forums, looked at a TON of different cases. So far I like the look of this: http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000164&products_id=6562
BUT I don't like the plastic over the keyboard and how annoying is that flap when you're trying to talk on the phone? I don't want to be fiddling with a GD flap while talking. Does the flap flip all the way back on itself?
SO, I need a well-balanced, high quality plastic clip (quick releases are good), that does not have cumbersome flaps (or at least has flaps that fold back on the case/go away when used as a phone).
Thoughts?
Thanks
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
skins07 said:
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
Click to expand...
Click to collapse
It seems that you can't slide the keyboard out when using this case... am I mistaken?
h0mersimps0n said:
SO, I've been searching around the forums, looked at a TON of different cases. So far I like the look of this: http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000164&products_id=6562
BUT I don't like the plastic over the keyboard and how annoying is that flap when you're trying to talk on the phone? I don't want to be fiddling with a GD flap while talking. Does the flap flip all the way back on itself?
Click to expand...
Click to collapse
I don't know about the book-style case, but I have the PDAir flip case, which has the flap hinge at the bottom. On that case, the front flap folds back very nicely. The snap strap on the top that holds the front flap closed doesn't fold back so well, but I've only had the case 2 weeks so it'll probably loosen up a bit over time.
dweinstock said:
It seems that you can't slide the keyboard out when using this case... am I mistaken?
Click to expand...
Click to collapse
To slide the keyboard, you do need to unsnap the cover and fold it back. The phone can still be left in the case. I rarely use the keyboard, but this could be a major issue for those that do.
skins07 said:
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
Click to expand...
Click to collapse
Do you have any pics with your phone in it?
Have you had any problems with the belt clip screw coming loose?
I think I need something that protects the screen too... I'll have to think it over...
3WAYGEEK- thank you for the reply- that's exactly the info I was looking for, now I just need to find someone who has the side flap...
Thanks guys
h0mersimps0n said:
Do you have any pics with your phone in it?
Have you had any problems with the belt clip screw coming loose?
I think I need something that protects the screen too... I'll have to think it over...
3WAYGEEK- thank you for the reply- that's exactly the info I was looking for, now I just need to find someone who has the side flap...
Thanks guys
Click to expand...
Click to collapse
Sorry, I have no pictures. There are images without the phone on the Boxwave site.
There have not been any problems with the clip and screw.
I do use a screen protector, but this case does leave the screen open, a feature I was seeking.
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
chibahawk said:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
Click to expand...
Click to collapse
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Praygo said:
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Click to expand...
Click to collapse
Yes I could see that the inside casing was a bit rough so sanding should stop the problem - but seriously that's a major issue.
Have you found that it holds the phone well though? Because I'm very upset that my phone fell out of it once already but maybe it was an error on my part and it wasn't secure enough...
I've never had the phone fall out of the body glove case.
i mangled my body glove case.
someone bumped into me and the phone fell out of the case AGAIN.
i ripped it to shreds and left it on the side of the road to rot into plastic hell.
i dont recommend this product.
I returned mine. I had the exact same issues (screen and phone falling out). It also didn't attach properly on the top left corner, it was always bowed out. I don't recommend it either.
Anyone got any else to share?
I was THIS CLOSE ( || ) to buying it. lol
Is there anything out there that's similar to it in design, but better?
returned
When all the way snapped on, mine pushed the top left corner so hard the entire screen would not respond to touch. Returned it.
My friend and i had the same issue. We just took it off messed around with it and put it back and it works fine, SOMETIMES it happens again but we just take it off and put it on.
Since there is not any other case that provides this type of protection we are keeping it. I rather my phone be safe than anything else.
I just ordered mine yesterday so I'm anxiously awaiting its arrival.
What exactly did you have to mod to get it to work? According to my readings, you just need to sand down the edges that connect with the screen right?
I may just buy the case and sand down what was mentioned. I like the design of the case..only one so far I really like.
I've been using one for about two weeks and am very happy with it. Had read about the screen pressure issue on other posts (searching helps folks), and scraped down the top corners before I put it on. Don't need a dremel tool or sandpaper. No problems, fits perfectly. The only warning is that it's a little dicey to take off once it's on -- it really fits snugly.
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Torkrench said:
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Click to expand...
Click to collapse
Could you give us the link for the ebay one please!
http://cgi.ebay.com/NEW-RUBBERIZED-...5|66:2|65:12|39:1|240:1318|301:1|293:1|294:50
That is the one I ordered, and the fit is perfect. The only thing I wish it had was the belt clip insert for the case included. I don't know where to find one, but I mostly keep it in my pocket anyway.
you guys want a good case that protects? check out the monaco aluminum case, it comes with a clear lens on it which I haven't removed but you could if you wanted quick access to the touchscreen. I work in the construction field and have yet to have it fall off my clip. I also dropped my tilt (when I used it) from about 8" off a ladder and it was perfectly fine. The aluminum case for the fuze isn't any more bulky than the body glove case either.
bilbobrian said:
check out the monaco aluminum case
Click to expand...
Click to collapse
I've got one of these as well...and while it does protect the phone very well it will also lower your signal strength. I've had these type cases for the Wizard and Tilt and now the Fuze...whenever I'm in an area where the signal was a little iffy to begin with I WILL either drop the call or be unable to answer with the metal case. So, stay away from the aluminum ones if you go into lower coverage areas (and no...the slots they cut in the back to help improve the signal don't actually help.)
I hope these come out soon. I really dislike how slick the entire phone is. When trying to have a phone conversation, and trying to rest it on your shoulder, holding it between your shoulder and face, it slides right out...
Same here. TMo was suppose to start doing the custom printed covers, but they are slick as well. It was 100 degrees yesterday and sweat doesn't help when you're trying to silde it open one handed either. TMobile has a rubberized shell for it, but it was way too bulky.
donepate said:
Same here. TMo was suppose to start doing the custom printed covers, but they are slick as well. It was 100 degrees yesterday and sweat doesn't help when you're trying to silde it open one handed either. TMobile has a rubberized shell for it, but it was way too bulky.
Click to expand...
Click to collapse
Yeah, I meant to mention those "skins" too, I am not a fan of those. One of my praises for this phone was it's slim profile, and adding one of those skins would make it just that more bulky. I like the material on the back of the Droid.
I like the battery cover on the back of the original MyTouch 3g, other then the fact that it slides open way to easy...
fermunky said:
I hope these come out soon. I really dislike how slick the entire phone is. When trying to have a phone conversation, and trying to rest it on your shoulder, holding it between your shoulder and face, it slides right out...
Click to expand...
Click to collapse
Have y'all looked into eGrips. Might be worth it for now.
Well again, those I am not a fan of. First: I am not sure how those attach, and if it is simply a stick-on, I'd hate to have it leave a residue when you go to remove it. And since it's a cover on a cover, it starts increasing bulk. If someone would come out with a replacement cover, just in a different material, I'd be happy
Edit: I also don't want something that would make it a pain to slide in and out of my pocket... those super grippy type covers do just that. They're great at keeping them in place on a car dash, or on your shoulder, but it's likely going to turn your pocket inside out, leaving you open to being bum rushed when the change falls out of your pocket.
fermunky said:
I hope these come out soon. I really dislike how slick the entire phone is. When trying to have a phone conversation, and trying to rest it on your shoulder, holding it between your shoulder and face, it slides right out...
Click to expand...
Click to collapse
Well, it *IS* called the Slide. Sorry, couldn't resist.
benmarvin said:
Well, it *IS* called the Slide. Sorry, couldn't resist.
Click to expand...
Click to collapse
Touche my friend.
fermunky said:
Well again, those I am not a fan of. First: I am not sure how those attach, and if it is simply a stick-on, I'd hate to have it leave a residue when you go to remove it. And since it's a cover on a cover, it starts increasing bulk. If someone would come out with a replacement cover, just in a different material, I'd be happy
Edit: I also don't want something that would make it a pain to slide in and out of my pocket... those super grippy type covers do just that. They're great at keeping them in place on a car dash, or on your shoulder, but it's likely going to turn your pocket inside out, leaving you open to being bum rushed when the change falls out of your pocket.
Click to expand...
Click to collapse
Maybe it's time to use what we call headsets?
They even have wired and wireless version of this gadgets..
N1M1TZ said:
Maybe it's time to use what we call headsets?
They even have wired and wireless version of this gadgets..
Click to expand...
Click to collapse
Eh, maybe I am old fashioned, but I hate headsets more than the battery cover I rarely use the phone in my car, so I see little use of the headset. Actually, I only use the headset when listening to my music.
OH, which BTW, if you used Subsonic, now you can browser your server using the phone's browser since it has Flash support, no need for the Subsonic app Maybe I'll post that in the apps thread...
The phone is great but it is way to slippery.
I was thinking of maybe taping off parts of just the back cover and spraying on a product called Plasti Dip just to give it a thin rubber coating.
schnem said:
The phone is great but it is way to slippery.
I was thinking of maybe taping off parts of just the back cover and spraying on a product called Plasti Dip just to give it a thin rubber coating.
Click to expand...
Click to collapse
I'm very familiar with plasti dip, and thats not a bad idea...
I put on some ghost armor on my device. It makes it a little more slip resistant. It was at one of the mall shops at a local mall.
-------------------------------------
Sent via the XDA Tapatalk App
Agreed on the slippin slide. I have a bench seat in my truck so i have to keep a t-shirt on the seat to hold my phone in place. (while streaming pandora into my stereo!)
So since gel skins have YET to show up at my T-mo store... I have been contemplating how to spray paint it or rubber coat it... If someone is bold enough I would love to see the photos.
Here are the potential problems
1. the holes in the back for the speaker.. we can porbably just poke them out with a pin after spraying.. hopefully it still looks pro
2. i started to pull off the front plastic and it seemed like the plastic screen cover was connected.. not sure if I want to mess with that... but it might look lame if the front doesnt match.
Possible anti-slide solutions...??
- some sort of stick on rubber tread that looks cool??Maybe if we find a cool piece of rubber tread that is made to stick on or we glue it one it could look cool and stop the damn phone from sliding.
p.s. my dream would be for someone to make a metal cover like the nexus (no i dont want a nexus I just like the finish that looks like an adults phone) with rubber tread lines built into it.. maybe I need to find a manufacturer. ..
I hate the slick back cover as well, i miss the cover on my G1 its the non-slick bio-hazard one. just the type of grip makes it great to slide in and out of pocket, less scratches, easier keyboard slide out.
Its too glossy for my taste i have to wipe the whole phone when im done with it for the night to make sure the finger prints are gone, gets annoying.
i'm looking for a nice matte cover as well, i hate the slickness(i dropped my phone because it slid out of my pocket). worst case scenario i might grab a replacement black one and sand it to a matte texture.
I am about to spray it with a satin black car trim spray... and if that doesn't work the next step will be a rubberized spray I think... Will post if it doesn't look like complete garbage lol
Well I hate to get ahead of myself but here is my rubber coated battery cover.. I am still waiting so patiently for it to completely dry. If what I used works then I will post a photo how to . Hang in there!
-------------------------------------
Sent via the XDA Tapatalk App
I was thinking on trying an invisibleSHIELD, has anyone ever tried one?
motorjonny said:
Well I hate to get ahead of myself but here is my rubber coated battery cover.. I am still waiting so patiently for it to completely dry. If what I used works then I will post a photo how to . Hang in there!
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
What product did you use on that, and did you tape off the holes or just poke them out with a toothpick type device?
One of the first things I noticed about my Atrix is that the battery cover doesn't sit completely flush on the right side -- there is a tiny gap, and the cover creaks whenever I put any amount of pressure on that side. It's making this otherwise nice hardware feel pretty cheap.
Is anyone else experiencing this? Anything I can do to fix it myself?
my atrix fits well tho, maybe u need a replacement
give it a pretty firm push. theres little tabs in there that feel like theyre going to crack but they will keep it slightly up if not forced down. just make sure its lined up good and it should be ok
trapjawmusic said:
give it a pretty firm push. theres little tabs in there that feel like theyre going to crack but they will keep it slightly up if not forced down. just make sure its lined up good and it should be ok
Click to expand...
Click to collapse
this.
when the chick at the store handed me the phone there was a gap on one side, i had to push on it pretty hard for it to snap into place
There should be a little gap on both sides, that's so you can get a fingernail in there to pull it open. If nothing is jamming the clips and it doesn't fit right...heck, it is just molded plastic and sometimes the plastic isn't molded right, take it back. See if they'll swap a cover for you.
Rred said:
There should be a little gap on both sides, that's so you can get a fingernail in there to pull it open. If nothing is jamming the clips and it doesn't fit right...heck, it is just molded plastic and sometimes the plastic isn't molded right, take it back. See if they'll swap a cover for you.
Click to expand...
Click to collapse
Uuh.... no.... you open the case by pulling from the top while grasping the sides. The sides of the rear cover are supposed to be sealed flush with the rounded side bits of the back of the phone.
Oooh, that was much easier!
NOW I get it.
Postal, you guys got me playing with my battery cover, trying to teach my fingers how to make it pop easily.
And I realized ONE SIDE had a tight fit, the other side had a fingernail-sized gap. Played around some more, and evrentually found that if I seated the "loose" side first, the other side would snap down tight, so the cover fits nice and tight all the way around.
It should matter, but apparently it does. If you carefully seat the "wide" side first, the whole thing may snap down nice and tight.
FWIW.