[TUT] HP iPAQ 61x, 91x Stuck @ Bootloader solition - Sable

Hi all.
I have 3 semi-brick iPaq device (612c, 614 and 912c). After do a ROM updrage from a bad miniSD card, these device onli show me HP logo when turn on. I'v search too many time and find a way to bring them back. @XDA-dev, I've saw someone have brick iPaq like me.
You need:
DNW (Include Driver file) http://www.mediafire.com/?zmnmzmwnjtk
Your device's Flash.DIO file. How to make a Flash.dio I'll post later. But you can found .DIO file via searching the web.
How to:
- Open DNW.exe, [Configuration] => [Option], change [Download Address] from 0xc000000 to 0x3000000
- Rename FLASH.DIO to FLASH.nb0
- Bring your Device too download mode: RECORD + OK + POWER or RECORD + OK + Reset to enter Download mode. Note: It's not Quanlcomm download.
- Plug your device to PC, and manually select driver to install (files are in SEC folder)
- Back to DNW.exe and [USB Port] => [UBOOT] => [UBOOT] and select Flash.nb0 just renamed and waitting for programed
I've done with these ipaq last week and return them to my customers. These Combine-key to enter download-mode can be wrong with 9xx device. I'll find another device to test later
This solution can change language of your device to language of .DIO file

How to make a .DIO file:
- You can download ROM update of your device from HP official web site.
- After download, extract (don't run) file to a folder by winrar, 7z or another archive manager. You'll see file named FLASH.NBF
- Open FLASH.NBF with a hex-editor like XVI32, and cut off first 3432 bytes. Then save file as FLASH.DIO.
- Now you can do a flash with this .DIO file and a micro-SD card, or with DNW tool at first post.

Great, thanks Paloma!!!
ipaq 614c resurrected with this great util.
Thank you.
P.D. Hp repair cost me 246 euro replacing all mainboard

Paloma, i have the same problem, but with a ipaq 6915. It is always into initial screen with blue screen and HP logo and in the botton right corner saying "No GSM" and ROM version. I would like test this solution, but when i run UBOOT the program always say, "Can´t open USB Device". I have installed the driver and it still saying the same.
Other cuestion. When you say "Download Mode" it is the same than "Bootloader Mode"?. Thanks

hi Carlengue.
This solution isn't apply to HP 6xxx.
I've got some ideal to help you, but now I ca'n 'cause I'm not at home, without my PC/laptop. I'll PM you later, ok?

i can't find the proper key combination. I've ipaq 914c

@ Carlengue:
Follow this link: www.mediafire.com/paloma and goto folder PPC tool. Download Uni_exitbootloader and run it with your phone plugged and active-sync disabled. Then you can try with one of two ROM I've uploaded (I don't know wich device you have, G3 or G4)
@ Ericco: I'm verry sorry, I'm in traveling and cannot find a HP-9xx now to test combine key for you. Can you try with VOLUME(up or down) + Record (or Camera) and Power (or Reset).
I'm sorry again about this incompatible.

Still can't find the proper combination.

Ok. I found it
Volume UP + OK (on side) + Reset
Rom on my 914c changed from NDL to ENG yeah

Hello Paloma,
Thanks very much for this info.
I have not used it yet but I can appreciate the knowledge since I had a bricked 612c previously and had to wait for 2 weeks for it to be fixed, I tried various software at the time but couldn't get to work.
I would like to kindly ask if you could please explain to us how we could modify a flash.dio or build a custom one. I want to know how I can modify Windows Startup files and decide on what software I want to have installed by default, etc... (that would be greatly appreciated).
Thanks heaps

ericco said:
Ok. I found it
Volume UP + OK (on side) + Reset
Rom on my 914c changed from NDL to ENG yeah
Click to expand...
Click to collapse
Hi Ericco,
i have also an ipaq 914c with italian language version, so i want to change the language into English. If you have done that please send file *.dio and *.nb0 to me via email: [email protected] (becasue im a nobie.., this smartphone is the first of mine)
thank you very much in advance
Rgds,

congtiger said:
Hi Ericco,
i have also an ipaq 914c with italian language version, so i want to change the language into English. If you have done that please send file *.dio and *.nb0 to me via email: [email protected] (becasue im a nobie.., this smartphone is the first of mine)
thank you very much in advance
Rgds,
Click to expand...
Click to collapse
Pls wait, I'm uploading and will give you the link
http://www.mediafire.com/?sharekey=034d5fbf0846aa8ed2db6fb9a8902bda

Paloma said:
Pls wait, I'm uploading and will give you the link
http://www.mediafire.com/?sharekey=034d5fbf0846aa8ed2db6fb9a8902bda
Click to expand...
Click to collapse
Hi Paloma,
Thank you very much, however i have a question
in case after upgrading ROM for ipaq914c, there will be few errors such as: audio or wifi...etc, if my smartphone can be back of ROM-original ?
I am waiting for your answer
thank you again
Rgds,

congtiger said:
Hi Paloma,
Thank you very much, however i have a question
in case after upgrading ROM for ipaq914c, there will be few errors such as: audio or wifi...etc, if my smartphone can be back of ROM-original ?
I am waiting for your answer
thank you again
Rgds,
Click to expand...
Click to collapse
Yes you can back to orginal ROM. Or you can download official WWE-ROM for 914 from HP support site and follow post #2 to get .DIO file

hi,
how can I backup the original ROM before I upgrade into English for warranty?
Is there any way?

ericco said:
Ok. I found it
Volume UP + OK (on side) + Reset
Rom on my 914c changed from NDL to ENG yeah
Click to expand...
Click to collapse
ericco,
can you explain me the exact steps you used? I want to do the same
and if I try the keys it does not work.

congtiger said:
Hi Ericco,
i have also an ipaq 914c with italian language version, so i want to change the language into English. If you have done that please send file *.dio and *.nb0 to me via email: [email protected] (becasue im a nobie.., this smartphone is the first of mine)
thank you very much in advance
Rgds,
Click to expand...
Click to collapse
Were you able to update it? can you explain me how?

Paloma said:
Pls wait, I'm uploading and will give you the link
http://www.mediafire.com/?sharekey=034d5fbf0846aa8ed2db6fb9a8902bda
Click to expand...
Click to collapse
Hi Paloma,
Thank you very much for your kindly assistances. However, after my iPAQ was upgraded with WWE-ROM downloaded from your website, then, my iPAQ was mistaken. it could not load OS, just appears a white color screen and the flash of camera is always light. at the end it stands there
Pls tell me what i have to do
Rgds,

congtiger said:
Hi Paloma,
Thank you very much for your kindly assistances. However, after my iPAQ was upgraded with WWE-ROM downloaded from your website, then, my iPAQ was mistaken. it could not load OS, just appears a white color screen and the flash of camera is always light. at the end it stands there
Pls tell me what i have to do
Rgds,
Click to expand...
Click to collapse
I'm very sorry, I'm on TET (Lunar-new-year) holiday now. I'll back to work after few days. Can you wait?
While, could you try to remove battery for a long time and insert back. Or try to enter boot-loader.
Camera's flash always lihgt => I think it's premotion of hardware failure.

Paloma said:
I'm very sorry, I'm on TET (Lunar-new-year) holiday now. I'll back to work after few days. Can you wait?
While, could you try to remove battery for a long time and insert back. Or try to enter boot-loader.
Camera's flash always lihgt => I think it's premotion of hardware failure.
Click to expand...
Click to collapse
i will wait for you and thanks alot! i hope that my ipaq will be back to life (i have just bought it one month before)

Related

XDA neo German to English

Thanks Machinagod for his nice tools.
Just flash O2 XDA neo from German to English.Here is the procedure:
1. Backup your data in your xda. ( including your sms and contact).
2. download the romupdateutility.exe file (by Machinagod).
3. extract the RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe to a filefolder. ( use winrar or winzip not double click .exe file or it will run immediately)
4. copy the romupdateutility.exe just downloaded and copy it into the folder ,then overlay the original file.
5. connect the xda to the PC:
6. then run the .exe file.
7. Ok, just It start now , wait about 10 minutes until it finish.
Thanks decmac and others (sorry cant remember the name) and all the xda-developers.
one problem is that after that, it will lost the homezone icon in O2. so you have to look for the software and setup it. just find one HZ_V0530_Magician_AKU2.6.CAB ,but didnt work well on wm5. So if someone can deal with it, please post it.
sskstar said:
Thanks Machinagod for his nice tools.
Just flash O2 XDA neo from German to English.Here is the procedure:
1. Backup your data in your xda. ( including your sms and contact).
2. download the romupdateutility.exe file (by Machinagod).
3. extract the RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe to a filefolder. ( use winrar or winzip not double click .exe file or it will run immediately)
4. copy the romupdateutility.exe just downloaded and copy it into the folder ,then overlay the original file.
5. connect the xda to the PC:
6. then run the .exe file.
7. Ok, just It start now , wait about 10 minutes until it finish.
Thanks decmac and others (sorry cant remember the name) and all the xda-developers.
Click to expand...
Click to collapse
Is it need to be unlock CID first? Or we can flash it with this step without any processes before?
If if have to do something before, please, post it to me, I am very new for flashing ROM and I also bought Neo fro German, too.
So please post the process previuos flashing for me.
Thanks in advance
ans also thanks machinagod for help everything
Hello, thanks for this. I presumed it worked fine for you?
I was wondering, is there some way to flashing it back to original? I mean, if i want to flash back to the o2 rom? Is that possible, and if so, how? I have not seen the o2 rom anywhere yet??
Can you tell me what you found to be the biggest difference in the new rom? Is there momre included software?
need not to unlock cid first, it can overwrite the original german rom.
FOR can
not get the german rom. therefore, cant write back to german rom.
sskstar said:
need not to unlock cid first, it can overwrite the original german rom.
FOR can
not get the german rom. therefore, cant write back to german rom.
Click to expand...
Click to collapse
Thanks a lot, sskstar
Can I ask one more, are there anyproblems after you flash your neo, i mean the stability or how about the OMAP overclock still work.
Thanks in advance
I get error: ERROR 240 while doing the ROM update. What should I do?
sskstar said:
Thanks Machinagod for his nice tools.
Just flash O2 XDA neo from German to English.Here is the procedure:
1. Backup your data in your xda. ( including your sms and contact).
2. download the romupdateutility.exe file (by Machinagod).
3. extract the RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe to a filefolder. ( use winrar or winzip not double click .exe file or it will run immediately)
4. copy the romupdateutility.exe just downloaded and copy it into the folder ,then overlay the original file.
5. connect the xda to the PC:
6. then run the .exe file.
7. Ok, just It start now , wait about 10 minutes until it finish.
Thanks decmac and others (sorry cant remember the name) and all the xda-developers.
Click to expand...
Click to collapse
Hi.
I tried this procedure on my Norwegian Qtek S200 with ExtROM 2.10.7.108. It all went fine until the phone started flashing. At 1% I got an error message on PC, which I don't remember, I clicked Exit and the update program stopped and nothing more happened on the phone. I restarted the phone and now the display only shows a red/green/blue screen and absolutely nothing happens. Phone won't start anymore.
Anyone who can help me out? Is there any way to flash the ROM from from SD-card? Help...! ;-\
Thanks, OrvarK
OrvarK said:
sskstar said:
Thanks Machinagod for his nice tools.
Just flash O2 XDA neo from German to English.Here is the procedure:
1. Backup your data in your xda. ( including your sms and contact).
2. download the romupdateutility.exe file (by Machinagod).
3. extract the RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe to a filefolder. ( use winrar or winzip not double click .exe file or it will run immediately)
4. copy the romupdateutility.exe just downloaded and copy it into the folder ,then overlay the original file.
5. connect the xda to the PC:
6. then run the .exe file.
7. Ok, just It start now , wait about 10 minutes until it finish.
Thanks decmac and others (sorry cant remember the name) and all the xda-developers.
Click to expand...
Click to collapse
Hi.
I tried this procedure on my Norwegian Qtek S200 with ExtROM 2.10.7.108. It all went fine until the phone started flashing. At 1% I got an error message on PC, which I don't remember, I clicked Exit and the update program stopped and nothing more happened on the phone. I restarted the phone and now the display only shows a red/green/blue screen and absolutely nothing happens. Phone won't start anymore.
Anyone who can help me out? Is there any way to flash the ROM from from SD-card? Help...! ;-\
Thanks, OrvarK
Click to expand...
Click to collapse
If you are still having the problem please take out the battery and wait ca. 3-5 secs and reinstall it back again. After doing this you can power up your device once more. And it should fine.
dont kill me
Hi.´m from Brazil, and I´m having a hard time to do the process.
Have some questions:
1- where do i find the RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.e xe ?
2 - The file i supose create is in the computer ?
3 - Where is the romupdateutility.exe ?
The most important, I have a Qtek S200 form FRance.
version Rom: 2.9.7.33 FRE
Date Rom: 2/14/06
Version de radio: 02.07.20
If need some info let me know
Thank you all, very much!!!
need RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.e xe
Brothers if somebody has RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe. then please upload it on rapidshare or some where else.Because I have tried a lot for this file but I could not find it. Thanking you for help in advance.
toor_rana said:
Brothers if somebody has RUU_Prophet_2090724_20907106_020720_QtekWWE_Ship.exe. then please upload it on rapidshare or some where else.Because I have tried a lot for this file but I could not find it. Thanking you for help in advance.
Click to expand...
Click to collapse
It's on the wiki... Look under "Official ROMs" and I'm sure you'll find it...
Why do some devices brick and other ones don't
I would like to do this German to English rom, but i'm afraid of bricking it :s .. Is this brick safe?
german to italy
salve a tutti!
qualcuno puo' dirmi
come cambiare lingua nel mio
O2 xda neo.
grazie
timmeke154 said:
Why do some devices brick and other ones don't
I would like to do this German to English rom, but i'm afraid of bricking it :s .. Is this brick safe?
Click to expand...
Click to collapse
If you flash an OS only ROM, and us soft/jump SPL, it'll always be recoverable.
where i can find the romupdateutility.exe?
i already download the version in english, but when it's going to start the process appears the legend "ID ERROR", what can i do??
You'll need to use Hard/Soft SPL.
l3v5y said:
You'll need to use Hard/Soft SPL.
Click to expand...
Click to collapse
??????? what is that??
and how i use it?

How to update ROM on O2 Orbit-solution

All,
I've exchanged many emails with the imei.check.co.uk team and also met personally one of these guys in order to be able to upload a new ROM to my O2 Orbit. I had excatly the same problem as many of you with ending the uploding process with "model invalid id" error message.
Now I'm happy to say we do have a solution.
So if you want to change your ROM (any), simply follow these instructions:
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Of course you can publish the instructions...
BUT PLEASE put a BIG WARNING! It will crash the phone in case you don't have a valid key file to perfom the last step: RUN THE UNLOCKER AGAIN AFTER THE ROM MODEL SWITCH TO RECOVER FROM THE DATA CRASHED MESSAGE!
Hello,
we found a way to flash ANY artemis roms in ANY Artemis look alike device (HTC Hero too).
Tools you need:
-hexworkshop from http://www.bpsoft.com/downloads/
-Any rom
-winzip or winrar
-http://www.imei-check.co.uk/C3v1Unlock.zip
a valid UNL file for your phone.
install hexworkshop and winzip/winrar
Take any rom for example: ART_HTCWWE_11240501_026790_WWE_Ship.exe
in explorer, right click on it and select "Extract files..."
Now it will unpack all the files
You'll have now "HTCWWE_shipsigned.nbh"
right click on it and Click "Hex Edit with Hex Workshop"
You'll see on the 5th row ARTE10000
Make it ARTE***** and save file
Now right click on ROMUpdateUtility.exe and "Hex Edit with Hex Workshop"
Search for word password.it will find it at 0x3E0B0 after password replace "BsaD5SeoA" with "IMEICHECK" and save the .exe file
Now connect the phone to the pc (normal way). run the C3v1Unlock.exe
when is asking for UNL file, disconect the phone from pc, press cancel, and
close the unlocker.
Now connect the phone back to the pc (in this mode it is) and run the
ROMUpdateUtility.exe
Now follow the instructions as the upgrade it will work.
After upgrade done, run the unlocker again and this time select the correct UNLfile.
Task Done.
C3 after flashing with any WIFI roms it will STILL not have WIFI!!!
Regards,
IMEI-CHECK Team
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Cheers, Martin
YESS, I have changed my GER rom to new HTC official ENG Rom, you are the best!!!!!! It's very simple to do...
yuppyyyyyyyyyyyyyyyyyy
the next step is.... backup the ROM I'm search ITA ROM form my HTC 3300.
see you later...
Good Discovery,
But the key is: We will have to pay 38USD for the "Proper UNL file" which is unique for every IMEI. Is it right?
Yeah, Thanks mr. Martin who is from Imei-Check Team. But we are still looking for a free solution.
Regards!
Tamagochi,
yes, first you have to go to imei.check and pay for the unlocking program and the unique .unl file.
P.S. I'm not a member of imei.check, just had the same problem as many Orbit users here...you can find my previous thread.
Works great on all versions.
Great support from the boys from emeicheck
Question about directions
Okay, I'm gonna try this. Do I still follow these directions exactly even though I have already unlocked the CID?
Also, when you see the line "ARTE1000" do you actually replace the "1000" part with the little stars? Sorry, I'm really new at this!
Thanks!
Yes you must do it all.
HELP
Everything went smoothly but when the device rebooted, it want me to "align the screen". It doesn't seem to be able to detect the stylus touching the screen! Can't get past that screen! Anybody know what I could have done wrong?
REF: HELP (Never Mind...)
I DID IT, I DID IT, I DID IT!!!! Just had to wait a minute or two and then everything seemed to work fine!!! TomTom is there, my WiFi is working! Thank you MAROSV and FRANCOBANCO!!!! If I can do it, ANYBODY can!! THANK YOU!!!
Hi KleineMaus,
I am wondering which ROM u used on your orbit that includes tomtom?
Or do you just mean you still had tomtom stored on your menory card?
Cheers, Towelie.
towelie said:
Hi KleineMaus,
I am wondering which ROM u used on your orbit that includes tomtom?
Or do you just mean you still had tomtom stored on your menory card?
Cheers, Towelie.
Click to expand...
Click to collapse
hi, I've just used the last HTC offical Rom (see xda ftp site..) that include TomTOm + 1 city map
byebye
Hi, I used the ROM on the Wiki page Dopod|English|DOPOD001|ARTE1****|1.25.707.2 ??/??/0?|1.25.707.104|1.25.0000|02.69.90|4.1.13.30| [Download|ftp://xda:[email protected]/Artemis/Shipped_Complete_Updates/ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe]|[Thread|http://forum.xda-developers.com/showthread.php?t=286639]
It worked like a charm. The only problem I had was that when the Orbit re-booted after the process finished, it didn't seem to detect the sylus. I just waited five minutes and then it worked. Guess it was still getting settled in with it's new ROM. I don't know where I had the TomTom before I started the update, but it installed the German maps which were there before but as a bonus it gave me a English speaking voice which I didn't have before. It came with a German voice and I couldn't change because I had not yet upgraded the memory and had no room. So, my update was super! The only little thing is that once I changed the screen color back to blue instead of that terrible green, I couldn't get the phone part (dialing pad) to change to blue. No biggie, as now I can use my Orbit in English. I can live with the green phone pad! Maybe somebody will tweak that one. Hope this wasn't more info than you needed....
KleinMouse,
the dialing pad can be easily changed as well....just do a little seach on this Artemis forum and you will find many links pointing to skins available for WM5 phone edition.
O2 Orbit ROM upgrade info
Hi,
my o2 orbit has ROM 1.25.206.2 WWE. I wanted to know if this is the latest ROM available for my phone. I got my phone 10 days ago and i gotta do a soft reset on it every day. I had the same kind of problems with o2 Atom. But most of the issues were corrected once the ROM was upgraded. Please someone update me on my situation. Thanks
I tried the steps but i'm always getting the ERROR[300] : INVALID UPDATE TOOL - This Update Utility cannot be used for your PDA Phone. Please get newer Update Utility
Anyone who can help me here? I already tried different ROMs but always the same message
Did you unlock with imei-check? What is your model ID ARTExxxx ?
Yes i did. My Model ID is ARTE100
Hmm, but the steps described above are necessary to follow only if your model is Orbit (ARTE200). If you have HTC P3300 or Dopod p800W or Artemis or MDA compact 3, then you don't need to do it this way. The only thing you need to do is to unlock with Imei-check. If it still doesnt work, contact their help desk.
Ok i see, very strange indeed. I did the unlock with the stuff from Imei-check but i still get the message ERROR [244] : INVALID MODEL ID . If i try the steps from your post #1 , i get the described error obove. I'll try to contact the guys from imei-check, i hope they can help me
Hi Kleine Maus, I read with great joy that you succeeded and I would like to feel the same way.... Could you kindly reply to me and give me some detailed instructions to follow? Hopefully this will work for my HTC P3300....Thanks in advance.... I really appreciate it. Best SiperX

Please Help - 614c/612c is now Bricked and Stuck at SDLoader - Possible Solutions Pls

Hello,
I did something stupid. I am hoping I can find a way to fix it without sending it back to HP.
I simply flashed the PDA using an incorrect file by copying it to my SD as a flash.dio and booting from it using the SDLoader. I thought if this happened I could still use the HP rom update utility while SDLoader is running, but it doesn't help!.
Now if I do a clean boot or even try to get into the SDLoader it just hangs and shows up but doesn't do anything.
when I have the PDA connected to my PC, my PC doesn't detect that there is a device there!
What could HP possibly do what I can't, do they have special software to bring it back to life or do they use hardware tools to flash it?
I have a strong feeling if I just knew what I am doing I could fix it. Could you please share some knowledge and possible solutions to resolve the problem
I really would like to avoid the cost of fixing it, I don't know how much it might cost as well
Thanks.
I have your's same issue.
I don't know what I can do.
I have exactly the same problem and I think your 614c is good and bricked. I called HP for hours, talked to people on their support forums, you name it. Nothing worked. The best suggestion I got was "take out the battery for half an hour, then hard reset several times in a row." Didn't work for me, maybe it'll work for you, I hope it does.
If not, I have a pretty exact estimate of how much it'll cost to fix. I'll let you know how it goes, I just shipped it to them this evening.
Mine is under warranty and I am kind of playing dumb at the moment so I'll see if I'll end up paying or not .
I sent it today, I hope they get it fixed quickly, we'll see.
I'll explain what I did wrong so people can avoid dangers / stupid things, I only wanted to do it cuz I wanted to learn really thats it.
I extracted diskimage_Ver.nb0 from the PDA using the following:-
pdocread 0x0 0x5000000 diskimage_Ver.nb0
then I renamed diskimage_Ver.nb0 to flash.dio and copied it to SD, this flashed fine and nothing went wrong, so this is going to be my method to backup my rom and hopefully nothing goes wrong with this method in the futrue.
I also flashed successfully the rom Zoltair has posted eariler. and I plan to test the russian rom as soon as I get the PDA back.
However, this is what I did wrong, I also grabbed the follwoing file : Part02.raw using:-
pdocread -w -d TrueFFS -p Part02 0 0x4cbc000 Part02.raw
then I wanted to flash it by renaming Part02.raw to flash.dio (which now I know its not the same thing duh), I copied it to the SD, flashed it and that's when the end of the world happened to my PDA.
I just wanted to learn how I can flash back Part02.raw which remains an unanswered question, I mean what's the point of dumbing it if I cannot restore it.
I understand now that the bootloader is messed up and the only way to fix it is by HP re-programming the chip on the PDA. or using JTag thing which I have no clue how to do it myself.
The problem is the only way for me to learn is to brick my device couple of times but I wish I was able to fix this issue myself so I can keep on learning.
I'd like to ask kindly people who brick their devices to explain what they did exactly so others can avoid these situations in the future and also if anyone has found a method to fix a dead bootloader it would be nice to share his solutions.
Thanks
Hi,
I faced the same problem two weeks back. Copied one of the file from the original HP upgrade package, rename it to flash.dio and tried to flash it via the SDloader (don't ask me why I did that). Bricked my 612 as a resulted .
Tried all means to recover but was unsuccessful. Brought it back to HP as my unit was under warranty. Upon collection, was told by the service staff that the ROM chip was corrupted and they gave me a new unit instead
That's great, I don't have mine yet, I hope I get a new one as well. but that's weird, how come they didn't fix it? don't they have the tools to do so.
How long before you recieved your new unit?
Thanks
[email protected] said:
That's great, I don't have mine yet, I hope I get a new one as well. but that's weird, how come they didn't fix it? don't they have the tools to do so.
How long before you recieved your new unit?
Thanks
Click to expand...
Click to collapse
Well, I was told that it was more cost effective to replace than to repair. I've waited for about 3-5 days for my replacement unit. I must say that HP's service is pretty good !
solution for no sdloader
hi, i was problem, but now is okay. please chek this, is the solution for mi. ihope help you.http://forum.xda-developers.com/showthread.php?t=459123
6xx, 9xx [email protected] Solition here
"Hi all.
I have 3 semi-brick iPaq device (612c, 614 and 912c). After do a ROM updrage from a bad miniSD card, these device onli show me HP logo when turn on. I'v search too many time and find a way to bring them back. @XDA-dev, I've saw someone have brick iPaq like me.
You need:
DNW (Include Driver file) http://www.mediafire.com/?zmnmzmwnjtk
Your device's Flash.DIO file. How to make a Flash.dio I'll post later. But you can found .DIO file via searching the web.
How to:
- Open DNW.exe, [Configuration] => [Option], change [Download Address] from 0xc000000 to 0x3000000
- Rename FLASH.DIO to FLASH.nb0
- Bring your Device too download mode: RECORD + OK + POWER or RECORD + OK + Reset to enter Download mode. Note: It's not Quanlcomm download.
- Plug your device to PC, and manually select driver to install (files are in SEC folder)
- Back to DNW.exe and [USB Port] => [UBOOT] => [UBOOT] and select Flash.nb0 just renamed and waitting for programed
I've done with these ipaq last week and return them to my customers. These Combine-key to enter download-mode can be wrong with 9xx device. I'll find another device to test later
This solution can change language of your device to language of .DIO fil "
Not exactly sure why you ressurected an old topic when there's the solution just a few topics down.
read this:
http://forum.xda-developers.com/showthread.php?t=459123

change operating language phone xperia x1

hey guys
i really need to change my operating language phone in xperia x1
i want it in English not in Dutch
can anyone help me plz
yopi_smoni said:
hey guys
i really need to change my operating language phone in xperia x1
i want it in English not in Dutch
can anyone help me plz
Click to expand...
Click to collapse
Just download and install an English X1 custom ROM from this site.
I changed the language on my phone from German to Finnish. Went to local service location and they changed it for me for 20€. Good option if u don't know what you're doing
where can i find that plz can u give me the link plz
yopi_smoni said:
where can i find that plz can u give me the link plz
Click to expand...
Click to collapse
Are you serious? LOL. Take your pick, man.
http://forum.xda-developers.com/showthread.php?t=477801
Instructions for flashing are in the thread.
thanks for the answer
well
i did that but i nothing happend
1- extract the file you got and rename it to ruu_signed.nbh
2- put the renamed file onto your memory card.
3- remove and insert the battery
4- press the volume down button and while pressing press the power button (keep both button pressed)
5- the mobile should start and give your three colored bars, keep on pressing.
6- a screen will come up showing it is starting to update. now release the two button.
7- wait till all update/intallation has finished.
8- remove and insert battery.
9- power on your mobile and do the initializations and wait for it to install some other programs and files.
10- phone will restart now for the final time.
here is what i Got
i get a 3 colour and
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
serial
then NO IMAGE and back to the above screen.
and i did that too
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/d...DisplayLang=en
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobi...ce-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder.
2) it is recommended you download only the X1_HardSPL_v1.zip unless you want to tinker with MFG SPL (MFG SPL 0.52 is a separate attachment).
3) you must Have Phone Synced with PC in Windows Mobile!
4) run X1_HardSPL.exe. (if you want to flash MFG SPL: at this point replace the extracted RUU_Signed.nbh with the MFG version of RUU_Signed.nbh)
5) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
but i got eurrer 202 what sgould i do now plz

In need o a little assistence.

Hello,
It's already a long time ago since i needed a Dutch ROM for the HP 6xx series, i can't ind this anywhere but now i finally have a Dutch device.
so now i heard something about ROM Dumping, i also understood that this has something to do with pdocread.
but as the rookie ( maybe even ''noob'' ) that i am, i want to ask the following question, how do i dump my dutch rom, what programs do i have to use or that, and is installing a Dutch rom the same thing as flashing it to your device? or do i have to convert files to .dio format?
all help is welcome!
post scriptum,
i got the 614 in every language available right now, so if you do me the favour for guiding me through this dumping, ill upload all the ROMS of any language you want, i got almost every language.
sincerley, alex
ok, i used DUMP TOOLS now and in the ''manual''of dump tools
it says i have to copy dump_gene_os_extrom.exe
to my device, i did this.
it also said that i needed a minimum of 70MB.
after like 5 minutes the device copied data to the storage card
im using a 1 gb micro SD of kingston.
now, it already copied 716mb on the SD card and growing.
i cant imagine a rom any bigger then like 120MB.
i tried alot of things so could someone please help me?
im willing to donate if anybody wants money for their time, no problem.
you are not using the correct dump tool, there is specific dump tool for 61x here. You need to connect to computer with activesync to use it
keyx said:
you are not using the correct dump tool, there is specific dump tool for 61x here. You need to connect to computer with activesync to use it
Click to expand...
Click to collapse
Thank you very much for this, it really helped me, i retreived the following files now from my device :
- diskimage_Ver.nb0
- part2.nb0.payload
- part2.nb0.payload.part1
- part02.raw
the files standing above, are the files that where retreived from my Dutch hp 614, now i want this rom, on my other 614 that ain't Dutch.
i already tried to rename the diskimage_Ver.nb0 to > flash.dio, then flashed that file into my 614, after that whas done it got stuck at the startup screen.
so is anybody prepared to help me out and tell me how i can get it to work.
P.S. for the ones that are going to link me to the thread where someone links to a Dutch ROM, that one doesnt work, it doesnt go any further then the start up screen.
if there's people that want money for their help thats absolutely no problem.
i just want my pda restored and dutch.
thank you in advance.
that is weird...it should work
anyway can you flash custom rom like my 6.5 or sergiorus 6.1 without problem?
also post your result from executing this command when your device is running a working rom:
pdocread -l
and
pdocread -t

Categories

Resources