Hello, I've a problem with my HTC P3600 (win Mobile 6.1), it doesn't start (also using hard reset); i've tryed to buy a new battery but the results are the same. Moreover if I connect the phone with the charge (without the battery), the led red brights, but doesn't start anyway.What can i do? Thanx for the answers
Can anyone help me?
you need to put the device in boot loader mode and attempt a reflash. i had the same issue and a reflash helped me.
Did you flash a new rom or something onto your phone after which this problem surfaced? If that was the case, try flashing another rom or better yet, check with the person that cooked the rom. You can PM them or something. How did this problem start and since when have you had it?
Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???
Hi everybody,i'm using cingular 8125 and i have a problem.I installed new windows and the phone discharged.I charged it directly with oder charger because with normal charger or true pc it's not charging.Now when i turn on the phone i see htc logo and nothing else.I even don't see the ipl/spl/gsm/os info.Just htc logo and nothing more.
I tried to enter bootloader mode,but it don't connect to pc.
Please help if you can
can somebody help me?
Hi someoneee,
Please, let's clear your problem.
The phone discharged while flashing the new ROM, or after, while normally using?
What other charger you've used? Was it compatible?
Which ROM have you flashed?
Cheers
The phone discharged while normally using,after flashing.
I flashed CR96 Touch HD™ v6.5.0.3.3 RC5 rom.
I charged battery directly with wires from other battery.
I can turn on the phone,but he won't boot.It's just that htc logo from CR96 rom.
I used CR96 rom's for long time,but this is first time when i have this problem.
Man, I can't figure what went wrong with you...
Have you used SoftSPL or HardSPL? Don't worry, I'm just asking
And which system are you on? I've heard that Vista and 7 aren't that good for flashing...
If nothing helps you, search for topics about "Wizard Love ROM". Maybe that can help you.
Good luck man!
well i tried to hard reset my device when turning on,it's said that it completed,but it doesn't change anything.Well i use windows 7,but for flashing i use windows xp mode.
and yes i used softspl and hardspl
by the way,i can't flash anything,because when i turn on bootloader mode,it doesn't connect the device to the pc.I don't know what to do..
hi anyone pls help,
i have one imate jasjam, the initial problem is i done a hard reset and the phone reboot and it wont finish running the customise application installation, after that the phone cant detect network, i had run a hard spl into the phone and then try to flash a rom that i download from forum but it only run 11% then stop then i realise that the rom i flash is for htc jasjam not imate jasjam, now my phone can only stay at the boot loader mode, i also try different rom but no luck so i think i ask for your help
here is my device details at the boot loader mode
IPL-1.04
SPL-2.10.01ipro
before i flash it i also cant find any radio rom version in this phone so i guess the radio rom also missing or what just not sure....
i think i flash the htc jasjam wrong model rom even now i flash back the original JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship this error message come out "ERROR [260]: update error" and it ask me to check my usb connection.
i search the forum and few member advice me to use mtty and i did tried that many time it didnt work, another member advice me to use this method "Formate yr memorycard & Unzip attached file in your memorycard named Hermimg.nbh & put yr cell in boot mode & follow screen instructions..........this illl boot yr celll out to boot mode......... " i tried that but the phone always stay at boot mode and no other instructions came out at all so im really lost and just hoping somebody can help me solve this problem...
can anyone pls guide me step by step of how to flash this phone back to normal, your help is much appreciated, many thanks.
Hi, i had the same problem flashing from the SD card. Are you using Vista or Windows7? I tried with Vista Format card, drag and drop renamed image onto sd card. Stuck it in the phone, reset and like you say hangs on bootloader. Then i tried the same thing from my Windows XP laptop, exactly the same format, rename drag and drop and everything works fine. Hope this helps
first i tried with vista then i tried with xp the problem still there, any other idea to solve this problem? thanks anyway for your advice
roms?
G'day, I've only really been reading about roms and these phones for only a few hours but I'm pretty sure that htc jasjam and imate jasjam are one and the same phone i think the said rom are used with all hermes type phones..
thanks and sorry for my ignorance if i'm mistaken
Hello,
I did a Hardreset on my XDA Mini and after that it loads when I start the files for the system and after that it changes back to the "Serial v1.02" screen.
How can I fix the phone that I can use it as before?
What is wrong?
I tried to upgrade to the new version of the o2 xda mini and after that it goes back to the "Serial" screen everytime.
I need help :/
I fixed this when I remove battery ant wait two hours. Or just try press soft reset button
Thanks for the answer.
I'll try but I guess that this won't work.
Would be happy if someone could give me more help...
If that don't work, try to reinstall your rom. If that happened when OS was loaded then that could be rom fail
hay hard reset again & plug your charger. try to this way.
reflash your ppc but use Windows XP
flash any shipped rom or coutlla's rom