Related
I've had my Qtek 9000 for a week. I've spent most of that week installing software, and getting it setup (using a lot of useful info from this site).
This afternoon it locked up, and wouldn't respond to any button presses (including the on/off button)
Soft resets result in it powering backon, but stopping at the boot screen, after displaying the ROM versions in red text.
Eventually, I tried a hard-reset. Same thing happens - process goes ok until it displays the ROM version, when it just sits there. I've tried removing the SD card and SIM card and hard-resetting. No Joy.
I had just installed OzVGA, and was testing it when this occurred, but that is probably just a coincidence (surely a hardreset should fix anything bad that happened there?)
I hadn't at any point played with the ROM.
What should I try next?
And, does anyone know if I'm going to be able to get support for this in the US from Qtek? (I bought it in the UK), new
Thanks in advance.
-Steve
RE
Have you try taking out the battery, leave it for a while, put back the battery and do a hard reset?
It may work
Re: RE
FOSA said:
Have you try taking out the battery, leave it for a while, put back the battery and do a hard reset?
It may work
Click to expand...
Click to collapse
Unfortunately, no such luck
I'd tried that before, but the battery was only out for a short time. This time it was been out for at least 15 minutes.
Does anyone know if there's any kind of hardware or diagnostic test mode it can be booted into?
-Steve
How about updating/upgrading thr ROM?
This might work. you'll have to reinstall everything again, though
Jorgee said:
How about updating/upgrading thr ROM?
This might work. you'll have to reinstall everything again, though
Click to expand...
Click to collapse
Thanks - I may try that tomorrow. However, I'm a little concerned that updating it with a new ROM might invalidate the warranty (especially if it's not a QTEK ROM)
I was hoping that there was some kind of hidden 'diagnostic mode' I could try first, before taking that step. I've also been looking everywhere on the web, and I can't find anyone else that this has happened to. This makes me think it may be a hardware problem, though the way it just 'happened' seems more like s/ware.
Anyway, I'm out today so this will have to wait until tomorrow. My biggest concern at the moment is how I'm going to get any warranty support in the US. All I have at the moment is a very expensive brick!
-Steve
Have you tried entering bootloader mode?
BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
Then the screen will go blank then show the words SERIAL but you have to look real good because the backlight will be off when the serial is displayed. If it does go there, try hard resetting from there:
__ + __ + RESET HOLE
Hope this helps. WHat's your ROM verison/language anyway?
Jorgee said:
Have you tried entering bootloader mode?
BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
Then the screen will go blank then show the words SERIAL but you have to look real good because the backlight will be off when the serial is displayed. If it does go there, try hard resetting from there:
__ + __ + RESET HOLE
Hope this helps. WHat's your ROM verison/language anyway?
Click to expand...
Click to collapse
Thanks - but no improvement. I do get the 'serial' screen (with v1.00 displayed at the bottom), but when I do _+_+reset from there, it just goes back to the 'normal' Qtek boot screen and sits there.
Unfortunately, not having access to the OS, I don't know exactly the ROM versions etc. However, the info displayed in red text on the Qtek boot screen (where it hangs) is as follows. How do you interpret this?
R 1.03.00
G 42.36.P8
D 1.13.64 WWE
Thanks for your help - I'm hoping I can get this resolved without having to find out how to get support from Qtek!
-Steve
thefixer said:
Jorgee said:
Have you tried entering bootloader mode?
BACKLIGHT BUTTON + POWER BUTTON + RESET HOLE
Then the screen will go blank then show the words SERIAL but you have to look real good because the backlight will be off when the serial is displayed. If it does go there, try hard resetting from there:
__ + __ + RESET HOLE
Hope this helps. WHat's your ROM verison/language anyway?
Click to expand...
Click to collapse
Thanks - but no improvement. I do get the 'serial' screen (with v1.00 displayed at the bottom), but when I do _+_+reset from there, it just goes back to the 'normal' Qtek boot screen and sits there.
Unfortunately, not having access to the OS, I don't know exactly the ROM versions etc. However, the info displayed in red text on the Qtek boot screen (where it hangs) is as follows. How do you interpret this?
R 1.03.00
G 42.36.P8
D 1.13.64 WWE
Thanks for your help - I'm hoping I can get this resolved without having to find out how to get support from Qtek!
-Steve
Click to expand...
Click to collapse
You have a WWE (English QTEK ROM) but since you cannot enter bootloader mode, I don't think you will be able to update. You might have to return your device to where you bought it
Jorgee said:
You have a WWE (English QTEK ROM) but since you cannot enter bootloader mode, I don't think you will be able to update. You might have to return your device to where you bought it
Click to expand...
Click to collapse
Jorgee,
I notice (in the HTC 'confidential' manual I just downloaded) that there is a diagnostic program. Apparently, I put it on an SD card, and do Power+Backlight+reset to invoke it.
Do you know if that diagnostic tool is available anywhere on here, or elsewhere on the web?
Also - I wqas trying to find exactly how to enter 'bootloader' mode (after I have the 'serial' screen). Should it boot differently from here when doing a hware reset (_+_+reset)?
Regards
Steve
Actually, when you see SERIAL, that means you are already in bootloader mode. One question, what ROM do you wanna update to? QTEK, IMATE, MDA, O2?
Do the following once you get the SERIAL ON THE SCREEN:
1. Open active SYNC, then choose FILE>CONNECTION SETTINGS, then remove the check on the USB option.
2. Connect the phone to the computer with the sync cable. This should change the SERIAL on the device to say USB.
3. Run the ROM Upgrade (whichever it is you chose).
This shoulod update your device. If you are able to enter bootloader mode (SERIAL) this means that probably your ROM (OS) is damaged. Just update it even to the same verison then it should work.
If you get Country ID error while trying to update or any other error, just inform me, i'll walk you through the process.
Jorgee said:
Actually, when you see SERIAL, that means you are already in bootloader mode. One question, what ROM do you wanna update to? QTEK, IMATE, MDA, O2?
Do the following once you get the SERIAL ON THE SCREEN:
1. Open active SYNC, then choose FILE>CONNECTION SETTINGS, then remove the check on the USB option.
2. Connect the phone to the computer with the sync cable. This should change the SERIAL on the device to say USB.
3. Run the ROM Upgrade (whichever it is you chose).
This shoulod update your device. If you are able to enter bootloader mode (SERIAL) this means that probably your ROM (OS) is damaged. Just update it even to the same verison then it should work.
If you get Country ID error while trying to update or any other error, just inform me, i'll walk you through the process.
Click to expand...
Click to collapse
Hi Jorgee,
I'd prefer to go for the QTEK Rom (I'm assuming, from the info I posted above that I currently have 1.13.64 WWE). I'd like to go for the same or later version of this, but looking on the ftp site here I can't see ay QTEK ROM upgraders.
I have checked that when I plug in the USB I get 'USB' appearing on the screen, so I'm hoping that a ROM upgrade will at least work, even if it doesn't fix my problem.
One other thing that concerns me. When I plug into USB (with either a PC or the AC charger) the LEDs aren't lighting to indicate it's charging. Obviously, when during the flash upgrade I should make sure I have a reasonably charged battery. However, I don't know if I do (or even if it's currently charging).
-Steve
I guess leave it charged using the AC adapter for an hours, then here's the QTEK ROM.
ftp://xdaupload:[email protected]/Universal
Under Shipped ROM's you should see the QTEK.
If you cannot find it, tell me, ill send it to you. Trying to avoid this because it is almost 60MB in size
Jorgee said:
I guess leave it charged using the AC adapter for an hours, then here's the QTEK ROM.
ftp://xdaupload:[email protected]/Universal
Under Shipped ROM's you should see the QTEK.
If you cannot find it, tell me, ill send it to you. Trying to avoid this because it is almost 60MB in size
Click to expand...
Click to collapse
Thanks - I'd already found it on the devbuzz site, and am currently giving the unit an hour or two's charge before trying this. Wish me luck!!
-Steve
OK, here's what happened when I tried to update with the same Qtek firmware:
Initial dialog (that shows old and new (to be installed) firmware versions had blanks for all three firmware versions currently installed.
Started the upgrade, and left it running (couldn't bear the tension of watching!). Came back, and found the following error message displayed:
"Error 113: Extended ROM Update Error"
The update tool indicated that I should 'try again'. I'm currently re-charging the unit, and hoping (against hope) that this error was caused by insufficent battery charge.
-Steve
Okay, but maybe it just didn't update the extended ROM but the OS rom has been updated properly. After this error, try the __ + __ + reset button and see if it does boot fine.
Jorgee said:
Okay, but maybe it just didn't update the extended ROM but the OS rom has been updated properly. After this error, try the __ + __ + reset button and see if it does boot fine.
Click to expand...
Click to collapse
No luck.
I've also tried re-flashing a second time, but this time I watched it to see what happens
As the radio firmware is flashing, a message to that effect is shown on the Qtek screen. Once that is finished, the upgrade tool starts the extended ROM flash. At that time the Qtek's screen goes completely blank. The, after a minute or two, the upgrade tool reports that the extended ROM failed to upgrade.
I am assuming that normally, while flashing the extended ROM, there's a message on the phone's screen to say what's going on?
I'm also wondering whether to have a go at flashing the ROM in one of the other ways?
-Steve
I heard sometimes just flashing the Radio only might work.... Then after that you can flash the rest. Just extract the contents of the ROM to a directory. Take note of the ff:
Radio : radio_.nbf
OS : nk_.nbf
Ext : ms_.nbf
I just rename/move/delete the MS and NK files then run the update
Jorgee said:
I heard sometimes just flashing the Radio only might work.... Then after that you can flash the rest. Just extract the contents of the ROM to a directory. Take note of the ff:
Radio : radio_.nbf
OS : nk_.nbf
Ext : ms_.nbf
I just rename/move/delete the MS and NK files then run the update
Click to expand...
Click to collapse
Thanks Jorgee. Still no real success, but I think I might be getting closer.
I've tried the above (using both the original romupdate_ut.exe and MaUpgradeUt_noID.exe - same results with both).
I've tried each of the three files individually (using the ones from the shipped ROM, as downloaded above)
radio_.nbf always seems to flash ok
ms_.nbf always fails right at the start, and nothing appears on the phone's screen
nk.nbf almost worked. It started, and got up to 87% (tried this 3 times), with the update showing on both the phone screen and PC. Then it failed with error 112, leaving the '87% complete' message on the phone's screen.
Soft or hard reboots still result in us just ending up 'hung' at the boot screen.
Once again, thanks for your help so far. However, I am beginning to give up hope!
-Steve
I have the same problem with my Dopod 900 at post http://forum.xda-developers.com/viewtopic.php?p=207524#207524
But mine is no problem with EXTRom Upgrade
Waiting for your advise!
Thanks
truongia said:
I have the same problem with my Dopod 900 at post http://forum.xda-developers.com/viewtopic.php?p=207524#207524
But mine is no problem with EXTRom Upgrade
Waiting for your advise!
Thanks
Click to expand...
Click to collapse
I wish I had a solution!!! I've spent about 20 hours trying to get this thing to boot!
One question though - how did you get the 'boot option' menu up (allowing you to clear the registry etc). I might try that on mine (I had assumed that a hard reset ALWAYS cleared the registry.
Given that I was playing around with ozvga before this happened, there's a small chance that might help (though I think not; as I can't see how that would also stop the flash update working)
-Steve
Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,
Since you havent really messed with SPL, i would say to take it back, since its still into warranty.
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse
Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?
You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.
Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY
Hi!
I have a HTC P3300.
I bought a 4Gb SDHC card, and it won't work. I read at the forum that I would need a different rom, so I downloaded "Artemis_Touch_4.02_Full_with_no_cube", which would have sdhc-support.
Then I executed "STEP 1 - activesync then uspl cid unlocking.bat", that finished ok, and then "STEP 2 - activesync then flash artemis touch rom.bat", which stopped with an error 302.
After a restart all that came up was the boot loader. I then tried to flash the original rom (HTC WM6 Dutch) from the computer, but that ended also in an error.
I tried the SD upgrade (rename .nbh file to ARTEIMG.nbh, put it on a formatted sd-card and load it in my phone), and it finished without errors, saying I should press any key.
After pressing a key, the bootloader popped up again.... :S
Can anyone help me? I have been searching the forum and trying to get my phone to work since 21:00 and I haven't got any progress at all!
well sorry for that
did you tried to make hard reset?
and once i had a completely dead artemis.. no sign of life..but it fixed by the following..(and maybe this may help you cuz the flasheng goes not like usual)
while your mobile is off.. press the record botton and the camera and it should starts with usual sd card flashing.
for me this what happens.
the setup was in three phases as i saw... and it took about 30 mins .
maybe it will works for you
I also tried a hard reset, wouldn't work.
I pressed and hold the camerabutton, but nothing happend...
Maybe the battery is empty, so I pressed and hold the camera button while plugging in the usb-cable.
It started the SD-upgrade, and is still busy.
The update ended with a "press any key to continue".
But when I pressed a key, the boot loader popped up :S
When I tried to flash another rom (NLD-FINAL), an error occurred (I believe it was error 270, not sure).
But then the normal startup screen appeared!
I don't know how, but the problem seems to be fixed!
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
As you can see in my previous post, I managed to flash the original rom.
I'm gonna try to upload an other rom some other time...
And with a patch I got the SDHC working too!
Thnx for your help!
y_bother said:
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
Click to expand...
Click to collapse
Hey, thanks a lot, I tought, my HTC-Cruise is ready for sending to repair, but with your info, it works again. I could install the WM 6.1 again, after System hangs up while booting every time. He found USB connection on a colored sreen. Thank you very much.
Jupeli
Hi guys.
I recently installed Onyx Micro on my Elf, and it's been great. I needed a "Home" panel though, so I installed a Home application that I had on my memory card, and after that reset, my phone's been unusable. When i turn it on, it either hangs, or gives me an error that says something to the effect of "phonesyslog has malfunctioned", and then freezes.
I can't get it connected with Actiesync, I can't hard-reset it either. Any idea what I can do?
Can anyone help me?
Hi,
Did you try removing the memory card? In case that doesn't help, try pressing the camera button while starting up, this should enter the bootloader mode, which enables you to flash a new rom. Do this in Windows XP, as Vista can cause problems. If you've never flashed a rom, try searching this forum for an appropriate rom and a how-to-guide.
Regards,
murosama
Hard reset should work and should be all you need to solve your problem. Make sure that you are performing the hard reset correctly.
For a hard-reset without access to the systems menu do the following:
Make sure the device is switched off, then press both the green and the red phone button and while keeping them pressed switch on the device.
A menu should appear, asking you to confirm the hard-reset.
(Upon confirmation, all data will be erased and the out-of-box state will be restored.)
In case that doesn't work, try flashing a rom that is native to your device
(as suggested above).
Good luck,
murosama
I got the same problem i tryed all off this but didn`t work did you find a sollution for yours?
Hello!
I am new here as you can see. this is not primary proplem anymore.
I installed XDAndroid GBX0C 2.3.7Build to my HTC balckstone and everything works well, but camera tells me "camera error; Cannot connect to camera."
is there any fix for that?`
and the other thing, when i boot phone it goes to win6.1 and i have to go settings etc. and boot it from haret.exe.
so am i done something wrong or something? Solved
So if somebody can help me i would be very pleased
Ps. And sorry my bad english, i just a finnish.
Edit: I try reinstall, i post is changes comes.
E: No changes, still not working.
EDIT!!!!
SO if someone can help me, place do it
E.
And this just happend, phone just stop working whit black screen.was have to took battery off, and then it took about 10-30min to boot to win again.
THIS IS PRIMARY PROPLEM.
AAAAND now it wont even start. stuck in "smart mobility"...
Please read post's for more information.
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.
Could I solve this proplem if i unlock and install custom rom? just wondering if that would help?!
Hi,
"Smart Mobility" screen
I had that problem too, and did a hard-reset.
Hold Volume Up + Volume Down buttons (hold hard) and press Power switch until you see the warning sign to confirm a hard reset.
The system will do a re-flash of the original Windows Mobile ROM.
Start Android by running HaRET from Windows Mobile
Yes, you have to run HaRET.
You can make it simpler by making a short-cut in Windows Mobile Start Menu.
Tap and hold on HaRET until you see the Dialog Box to Cut, Copy, etc.
Tap Copy.
Go to Device-Windows-StartMenu, paste as a shortcut
These steps are in the Touch HD Manual. If you do not have one, download it from the HTC website.
chan.sk said:
Hi,
"Smart Mobility" screen
I had that problem too, and did a hard-reset.
Hold Volume Up + Volume Down buttons (hold hard) and press Power switch until you see the warning sign to confirm a hard reset.
The system will do a re-flash of the original Windows Mobile ROM.
Start Android by running HaRET from Windows Mobile
Yes, you have to run HaRET.
You can make it simpler by making a short-cut in Windows Mobile Start Menu.
Tap and hold on HaRET until you see the Dialog Box to Cut, Copy, etc.
Tap Copy.
Go to Device-Windows-StartMenu, paste as a shortcut
These steps are in the Touch HD Manual. If you do not have one, download it from the HTC website.
Click to expand...
Click to collapse
I have tried hard reset, but that didn't work, and tried to put original rom too, and nothing happened. I have 2 original roms
RUU_BlackStone_HTC_FIN_1.14.414.2_Radio_52.49a.25.26_1.09.25.14_Ship
RUU_BlackStone_HTC_FIN_1.56.414.0_Radio_52.62.25.34_1.13.25.24_Ship
but those didint work. i will try today againe. and then if it going to work i will put that haret to start menu.
I'll try that 1.14 first...
flashed that 1.4 rom and waited about an hour and nothing happend... i jsut did hard reset and wait againe if it gonna boot now...
i was thinking that should i put custom rom, coz if something went wrong whit the official?
I mean if there is something wrong in phones hard drive? like something wrong whit registery or something?
something that wont let win start. if there is, how i can fix that?
masentava said:
Hello!
I am new here as you can see. this is not primary proplem anymore.
I installed XDAndroid GBX0C 2.3.7Build to my HTC balckstone and everything works well, but camera tells me "camera error; Cannot connect to camera."
is there any fix for that?`
and the other thing, when i boot phone it goes to win6.1 and i have to go settings etc. and boot it from haret.exe.
so am i done something wrong or something? Solved
Click to expand...
Click to collapse
GBX0C2.3.7 Build is on SD card.
You will need to boot from Windows Mobile first, then run HaRET to reboot to XDAndroid.
If XDAndroid hangs, you need to remove battery, put back battery and power on. Then you see Windows Mobile and do above step again.
Always, from XDAndroid to go back to Windows, you need to Power Off, and then Power On again.
chan.sk said:
GBX0C2.3.7 Build is on SD card.
You will need to boot from Windows Mobile first, then run HaRET to reboot to XDAndroid.
If XDAndroid hangs, you need to remove battery, put back battery and power on. Then you see Windows Mobile and do above step again.
Always, from XDAndroid to go back to Windows, you need to Power Off, and then Power On again.
Click to expand...
Click to collapse
I undestood that... but thats not the proplem anymore coz windows wont start, its stuck in "smart mobility"
i tryed to flash original rom's bot that didint work....
so prolem is how do i get windows back to work?
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.
masentava said:
I undestood that... but thats not the proplem anymore coz windows wont start, its stuck in "smart mobility"
i tryed to flash original rom's bot that didint work....
so prolem is how do i get windows back to work?
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.
Click to expand...
Click to collapse
You say you are flashing the original ROM. You mean the original HTC Windows Mobile 6.1 ROM? I understand you can only get this done only from HTC authorized centers.
(800) stedntf
chan.sk said:
You say you are flashing the original ROM. You mean the original HTC Windows Mobile 6.1 ROM? I understand you can only get this done only from HTC authorized centers.
Click to expand...
Click to collapse
I have
This
RUU_BlackStone_HTC_FIN_1.14.414.2_Radio_52.49a.25.26_1.09.25.14_Ship
And this.
RUU_BlackStone_HTC_FIN_1.56.414.0_Radio_52.62.25.34_1.13.25.24_Ship
Blackstone/HD Links | Guides | Stickies | Roms | Read before posting
http://forum.xda-developers.com/showthread.php?t=999925
U have to install HTC USB Sync Drivers drivers
Put the phone into bootloader by pressing volume down + power button
plug the usb cable to the computer/laptop
and then run the shipped rom executable file... when the tricolor screen displays USB at the bottom.
else extract the RUU_signed.nbh or any file with .nbh extension from the shipped file with zip viewers like 7-zip
rename the file to BLACIMG.nbh
Put into the root of memory card
put the phone into bootloader and follow the screen instructions..
And the most important thing... search the forum.. before posting..
Hope this works for you
Hi there! I think that you can't reflash even a Original ROM without unlock the phone with new Hard-SPL from Olinex ,considering that you have tried a Hard Reset and nothing happened ,your last option is to unlock the phone and reflash the ship ROM ,or to flash a custom ROM ( is not a good solution if you still have warranty,but still you cand revert your stock SPL:good so ,you have nothing else to lose , all is left for you is to try what i said before . If you don't know how to do it,let me know and i will post the exact links to instructions.
Hi all,
You can try a NAND ROM like the new release of Fagyi. There is an easy step by step manual to installation. You will lose winmo, but you will have a real android.
It looks pretty and he has solved many of the issues of previous versions.
Regards
CristianCRS said:
Hi there! I think that you can't reflash even a Original ROM without unlock the phone with new Hard-SPL from Olinex ,considering that you have tried a Hard Reset and nothing happened ,your last option is to unlock the phone and reflash the ship ROM ,or to flash a custom ROM ( is not a good solution if you still have warranty,but still you cand revert your stock SPL:good so ,you have nothing else to lose , all is left for you is to try what i said before . If you don't know how to do it,let me know and i will post the exact links to instructions.
Click to expand...
Click to collapse
well, maybe i will try to unlock, i looked some instruction, aaand didint understood
So if there is quide to dummiest dummies, so i think that would help me!
But thx to all answers!
Do a Search and read the posts
masentava said:
well, maybe i will try to unlock, i looked some instruction, aaand didint understood
So if there is quide to dummiest dummies, so i think that would help me!
But thx to all answers!
Click to expand...
Click to collapse
You need to understand what you are going to do or you may end up with a phone that does not work anymore.
Do a search of the forum and read the posts. There are so many.
http://forum.xda-developers.com/sitesearch.php?q=unlock blackstone