Help, purchased Hermes off of eBay, stuck in Bootloader screen, was unable to connect to usb originally, did flash from SD to OEM WM5. Have been able to connect to usb since will flash ok, get successful flash screen on computer but Phone screen reverts back to bootloader. SPL is 2.03 1PL is 1.04. Using XP. Thought may have been attempt to flash different ROM w/o unlocking CID/SIM, tried to run Hermes SIM_CID_Unlock_v3a stops at 7% reverts back to bootloader and usb disconnects until I uplug usb cord and reattach. Any suggestions would be greatly appreciated.
Thanks
Related
Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!
Hi, I have a TMobile MDA with IPL 2.26 and SPL 2.26 and I was trying to put a new rom but the program gave me an update error when reached 99% an now it is stuck in the boot screen (shows in the bottom USB connection) but when re-running the program it does not connect and activesync does not detect the phone. Before the rom update program ruu gave me the that said the phone required a newer program version.
Did I screwed the phone or there is a solution?
Thank you in advance for your help and best regards
Issue Was solved downloading from T-MOBILE the updated ROM and executing the program
Nick
Nope, you're good.
As long as you can enter bootloader and it reads usb in the bottom corner, your wizard can be saved. Don't worry about active sync, it won't read. Get a stock rom from your provider...if Tmo, it is available on their website. Plug in the usb and get into the tri-color boot. Run the stock ruu. Do not let anything interfere with the process, so disable your screensaver, don't let cats or kids near the usb cord, etc (trust me on that one!). NBow flash the stock rom. It will take 10 minutes roughly, be patient, DO NOT unplug usb for any reason...let it flash and reboot. Once flashed, make sure you are cid/sim unlocked...use lokiwiz (read the sticky on unlocking). You cannot change roms from stock to custom without first unlocking. If you are already unlocked, once you have the stock rom re-installed, you can flash to a custom rom. The linky in my siggy explains in detail about reviving a "bricked" wizard.
Ok,
So I installed the T-mobile UK radio rom on my unlocked cingular HTC 8125 with a t-mobile sim. Upon reboot I get no phone service, it acts as though the phone is shut off but it's not. On bootup when it displays the IPL/SPL and OS and all that there was a line between the IPL / SPL lines and the OS line which used to have something on it, but now it's blank. Here's the worst part, it no longer recognizes on USB or under activesync, I tried to get it to work with bluetooth using a usb bluetooth adapter, but to no avail.
I need to know if there is anyway to get it working again, anyway at all to get it to connect or something so I can install a new radio rom on it.
Please help.
Help me too
I am in exactly the same predicament. I have spent days searching for a solution. Nthing so far. Anyone?
Rogue23
Well,only flashing a Radio Rom,never bricks a phone,cuz it doesn't include any IPL/SPL in it Its just a bad flash.Either,Try a Soft Reset or Hard Reset,if works fine,otherwise,get the phone in bootloaders (multicolor screen) and flash the cingular official Rom,it'll recover back. The phone doesn't get detected via usb or doesn't activesync if there's no working Rom (OS) on it,but if you are able to get to bootloaders and connect the phone via usb cable, a small usb appears at the bottom of the bootloaders screen,it means it has established connectivity and you can flash a rom.
Secondly if the ohine is not SIM unlocked,it won't work with a T-mobile SIM,you'll have to get it sim unlocked if you plan to use a different sim and network.
ericmda
Be a little more specific about the problem and remember to always post the version of the phone OR vital data of the phone to ask for an advise.
Cheers!
been done
yeah,
I've been able to get it into bootloaders, the usb pops up in the corner but when I try to flash a rom it it gives me a no phone connected type of error. which is really messed up because the first time I put it into bootloaders it worked, but I didn't use the official rom so the flashing didn't fix it.
If flashing the radio rom isn't supposed to brick it then well somehow mine is apparently the exception to the rule. Still gonna be working on it throughout today though, so any other suggestions?
I have a T-mobile MDA G3 U.S. and I had it unlocked and flashed with some custom ROM I don't remember. I got a Herald couple days ago so I gave it away to a friend. As requested by him, I flashed it with a Chinese wm6 rom. However, it turned out he wanted to use touch flo and stuff so we found another Chinese ROM with that and flashed it. During the flashing process, I noticed an unusual long waiting time after the progress bar got to 100%. After succeed, the ROM turned out to be the original Chinese ROM again. I figured there might be some problem with unlocking so I unlocked it with lokiwizard tool again, but this time it won't even lemme update the ROM! RUU tool said "Communication error". The problem turned out to be the phone cannot establish USB connection under 3 color mode(when I plug it in under 3-color, computer sounds like you plugged in a failed USB device). Now I can't even flash it with the original T-Mobile 2.26 WWE! I tried hard reset and everything but I still can't connect under 3-color mode. Though that ActiveSync worked fine. Please help me!
(Maybe I can, in some way, flash it without USB?)
You got to have usb working to flash,check if the usb cable is faulty or the mini usb port of the phone.Did you try with a different usb cable or on a different usb port of the pc,even you can try with some other pc.If the usb cable is faulty,replace it,but if its the mini usb port of the phone,it'll have to be either repaired or replaced.
There's no other possible method to flash a rom,the only other method which might be possible is through Sdcard backup rom using MTTY commands,but its only possible if you had already backed up the rom on a Sdcard and the phone is already CID unlocked.
I tried replacing two more USB cables and on a different computer, still no luck.
Wierd thing is, I have USB working under ActiveSync, but not in 3-color mode. I don't know much about how the phone works but I figured the 3-color mode might be a part of SPL? And somehow I've damaged it. The phone still works fine, plus ActiveSync. It's just I can't flash it anymore.
thanks to zabardast,
it turned out to be I had tried with 2 faulty cables... =/
Well I'm still stuck with this ROM, I used lokiwiz03a to unlock my phone and it worked fine(IPL/SPL 2.26). When I was using RUU to flash it, I still have the same problem. Nothing was flashed, nothing happened. What should I do?
flatcoke said:
thanks to zabardast,
it turned out to be I had tried with 2 faulty cables... =/
Well I'm still stuck with this ROM, I used lokiwiz03a to unlock my phone and it worked fine(IPL/SPL 2.26). When I was using RUU to flash it, I still have the same problem. Nothing was flashed, nothing happened. What should I do?
Click to expand...
Click to collapse
Download WST_4.2.2 tool and run the 'CID Action' button to verify the CID lock/unlock status of the phone and proceed further,you need to use lokiwiz02b to work on G3 device for CID unlocking and not lokiwiz03a.
Secondly, Hard Reset the phone,it might be that Extended_Rom has got corrupted and download the official carrier's rom and flash it to recover back to its default working status and than go further.
Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.
Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370
whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.
beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader
It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.
here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.
Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.
crap, my phone just ****ed off again. Same deal as before. Hate being broke.
help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you
what is your bootloader version
htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3
are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.
tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41
You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.
Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe
yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17
Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.