Hi i have 2 part question my phone is an htc 8125 cingular sim card unlocked phone it has windows mobile 5 on it and i have the IPL 1.05, SPL.3.08 on it.
I did this but installing the IPL_SPL_3.08 rom. Anyways Im trying to get it back to IPL 1.05, and SPL 1.05 by installing the button rom and i seen the beer screen and it loads up to windows mobile 5 but keeps staying at IPL 1.05, and SPL 3.08 is there away to get it back to 1.05,1.05. I tried a few methods but aint working. Would keep reflashing a few times with the button roms get it back to 1.05,1.05. I tried with, newromupdateutility_wizard_noid. and didnt work i tried with rom update and didnt work. When a rom loads up and gets stuck at 99% and then i get a message with activesync saying lost communication error message whats does that mean and it saying try restore.
Also can windows mobile 6 with touch flo install on this phone or no. I was tring to do that with but all i got was it going back to windows mobile 5 and doesnt upgrade to wm6. Do i first need it to get it back to 1.05,1.05 using the button rom then use ,lokiwiz02b to do the unlocking(mind you my phone is all ready sim unlocked). and then flash a t-mobile or cingualr rom and then do the update with a windows mobile6 rom.
Whats a good windows mobile 6 with touch flo that works good on this phone can u maybe post a link
thanks for the help
deleted for inaccurate information
First,you shud have CID unlocked the phone prior to upgrading to 3.08 bootloaders,cuz it becomes very difficult and frustrating to downgrade from 3.08 to 1.xx.Now the only way is to first try to downgrade to 2.xx by flashing the official carrier's rom and when completed downgrade to 1.xx through Button's 1.05.You can only CID unlock the phone,if its 1.xx,which you already know.
Secondly,it'll only upgrade to wm6 if its cid unlocked.Try to flash ipl/spl 3.08 again and make both ipl/spl 3.08 first and then downgrade to 2.xx by flashing the official stock rom,it might work.
Cheers!
i have a problem,my phone is blocked on start up screen on tap screen to begin use your device,i have the radio 1.17,and energy rom ,hspl olinex,i have tryed the original rom radio,all the radios begining from the original,but the same thing.
does any of you know about this?
Hi, I just got my HTC HD2 back from repair. Before I sent it, I had a problem reflashing to stock rom before sending it in, and stock HSPL... when I turn the power on, all I get is a white triangle with an exclamation mark in the middle...i thought if i sent it in like that, they would help me restore it but they didn't....how do i get my phone to work again ]:
enter bootloader, flash a compatible stock rom. phone should be fine.
whilst in bootloader take note of what spl says.
Everytime I try to flash a ROM, it gives me the ERROR [294]: INVALID VENDER ID error...
right now my phone is stuck on the bootloader screen...it says
HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
and if i take out my SD card, when I turn the power on, i get the triangle exclamation mark ]:
I take it its a stock rom you are trying to flash?
I'm not positive which is the stock rom for my phone. It's the HTC Leo HD2 T8585...I remember it being 1.66 but i'm not positive. I downloaded
RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
still the same error :|
i also tried
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
and
_HTC HD2_RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
all give me the same error :|
The Invalid Vendor ID error means that the rom you are trying to flash is not meant for your phone and the ones you are using are for a different vendor/operator/area than the one who supplied your phone. You either need to find the correct rom or else you need to install HSPL in order to flash any rom you wish.
You current spl is 1.42.0000 so trying to flash roms based on 3.14 will definitely not work as will most of the 1.66 based roms, as unless you use HSPL the rom needs to match the spl version on the device.
Try looking here and concentrate on the 1.48 or 1.43 roms
You can of course also try going to the HTC site for your area, entering your device S/N and try to download the rom for your device.
I just finished downloading and tried
RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship
and
RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
...no luck..
i also went on HTC site..tried 4 different rom updates but when i enter my serial it says "Sorry, this software download is not suitable for your device" for all of them...
if its any help, it was like this because i remember doing something with using my SD card and taking a file and changing it to LEOIMG.nbh...
forget all that, and forget what i just sent you in PM.
you have spl 1.42.0000, so, get hspl2 (see lilnk in my sig) enter bootloader, run hspl2.exe (right click it, 'run as administrator')
choose, say, 1.66.hspl (it will automatically offer you 1.42.hspl, you can change it in the dropdown, or leave it as 1.42.hspl, it really doesnt matter)
when the phone restarts, quickly press and hold volume down, the phone will re-enter bootlader, flash a rom, any rom, over USB, so long as it isn't a 3.14 rom.
report back.
ah crap... I got everything working again after installing HSPL again before you posted...then i flashed a rom...and realized that HTC didn't fix my touchscreen problem so I have to send it in for repair...AGAIN. so I tried to remove HSPL AGAIN so I don't void the warranty...now i'm stuck at almost the same situation except it says SPL 3.03.0000
...and now i get a exclamation mark with a traingle but this time, under it, it says "Software update failed. Please try again."
ryennn said:
ah crap... I got everything working again after installing HSPL again before you posted...then i flashed a rom...and realized that HTC didn't fix my touchscreen problem so I have to send it in for repair...AGAIN. so I tried to remove HSPL AGAIN so I don't void the warranty...now i'm stuck at almost the same situation except it says SPL 3.03.0000
...and now i get a exclamation mark with a traingle but this time, under it, it says "Software update failed. Please try again."
Click to expand...
Click to collapse
well, that will be fine for warranty, because its a stock spl.
Basically, it sounds like what you just did was use hspl to flash the 3.14 rom from sd card, cos that lets the flash start, but it applies spl 3.03 which then checks teh rom and finds it doesn't match, and so fails. If hspl wasn''t there, it wouldn't let you get even that far.
So, you have spl 3.03 and no working rom.
You need your actual stock rom, not just 'a' stock rom, (im not scrolling to see if you posted it yet, but if its operator branded, you gotta get the right one) doesn't matter which version, 1.43, 1.66, 1.72, whatever. get that and flash it. USB should be fine, but if it fails go for leoimg on sd card.
Failing that, if you can get hold of another working winmo phone for afew minutes, you can probably revive it (and indeed flash teh 3.14 rom if you like) with a goldcard.
EDIT - oh, does your phone only work with one sim? if so, your first stop would be try teh branded one for that operator.
I think I'm just going to leave it if it's fine for warranty and call HTC to ask them if they can reset everything for me...i don't want to mess it up even more ]:
ahh well theres the unknown see, , cos in theory the only way you can GET that stock spl on your phone is if you have been playing with hspl (or maybe if you're an electronics engineer / 1337 mobile hacker, heh), , now if they want to be funny, perhaps they could call your bluff, , , no one has reported anything like that to my knowloedge, and it doesn't break any unauthorised software rules, so who knows.
i don't remember which one my stock rom was...i THINK its 1.66 but its not working... :\..
I bought this phone in China seperately without a contract so its unlocked/not branded.. its the T8585 model...
that's why you need to spend some time on the htc website, try to download roms using your serial, when it lets you have one, that will tell you your original stock.
When I enter my serial, they all say "Sorry, this software download is not suitable for your device"... \:
hehe, , then you are on the wrong htc region website. all the roms are there, somewhere.
could always phone htc and ask them which is the stock rom for your serial.
Nice, okay, the 1.66 that I downloaded from Middle East & Africa-English Country on HTC site worked after entering my serial...Now I have SPL 1.42.0000 .
Now I just gotta wait another 2-3 weeks before I get my phone back from HTC ]:
Thanks for the help! Appreciate it.
Hello, I am a flashing noob so please bear with me! I have a CDMA HTC Touch with Cellular South. It was locked and running radio 2.32.
I was able to unlock it to coker 2.31 and it powered up fine after that. Then following these instructions (http://forum.xda-developers.com/showthread.php?t=592964). After that i tried to load the stock radio for sprint so i can get the radio update for the GPS. Well I was able to active sync and start the load and it stopped. i tried again and it would not load it. This was the load from the HTC site. Sooo....I went to load this ROM (http://forum.xda-developers.com/showthread.php?t=711839) and it flashed fine. But then during reboot it stops on the black screen that shows the version and shows the load but then underneath the load it says "no radio".
Because of this I cannot sync the device and of course I cannot get to the home screen. I can however load another ROM but same thing, no radio. What did I do wrong and how can I load a radio load through bootloader? Or a ROM that has a sprint load in it other than the stock sprint rom from the site that needs to be sync'd?
Thanks,
Simtech2
Hey there Community,
I really don't know much about mobiles, especially the HTC HD2 and flashing ROMs,
but somehow I got Android to work on my HTC HD2 1 year back and now wanted to sell my phone because I got a new one.
Therefore I needed to set up the factory settings and get Windows Mobile 6.5 back on my phone..
Unfortunately I failed hard while following the instructions of a tutorial that said I only needed to rename ruunbh to leoimg and put it on my SD-card and so on.
Halfway the update was interrupted and since then Iam getting "00028002 Not allow" error and can only boot to the bootloader saying "Upgrade ROM code error Please try again" And the usual things in the red disctrict and at the bottom it says that I got an USB-connection which seems to be wrong, because I can't see the device and so on.
I tried to install HSPL4 but it failed due to no USB-connection.
So what can I now do to make it work again? Iam really frustrated
Flashing image from sd is all good if it original correct country/vendor rom, if not you get your problem & things can be tricky as HSPL was replaced with standard SPL so care must be taken.
Either find a correct Vendor/country (CID) ROM for your HD2 or get it in bootloader & able to flash HSPL.
Would of thought for resale a good Android build would be more desirable.
I know what you mean, but the problem is that I just don't know what to do..
My phone is not branded or anything, so I couldn just go to htc.com and get me the newest winmo Rom?
The Problem is, what to do then, exactly?
It seems that I can't flash anything because I dont got usbconnection..
So no idea to original ROM country vendor !
usb connection may be due to driver issue on PC, install Activesync if on XP or WMDC 6.1 for Vista & Windows 7 then retry connecting hd2 via usb .
*Also make sure you know your version of HD2 & be aware of .51 radios killing US T-Mobile HD2s.
Try to flash 2.08.HSPL only (also in HSPL4). It is enough. You can also try these drivers to fix your USB connection.
And here you can find offical ROMs.
Drivers linked above are not suitable, install activesync or WMDC is best option.
Finding original ROM is not going to be easy if you have no clues to origin of handset ...
Also, just cost you don't "see" the phone from the p c doesn't mean you don't have a USB connection.... it will never show up in your drives list like it does when an os is running, and activesync (or wmdc) will also not see the phone when it's in bootloader.
If the phone shows "USB" (and your PC may even "ding" when its plugged in, that's all you can expect unless you look deeper,, into the hardware list, for example.
What does hspl line say?
I'd do....
Hspl4, choose 3.03.hspl (NOT 3.03.0000)
Flash unbranded 3.14 rom from USB
Report back.
I have same story - 00028002 not allow+no usb.
no one stock rom can be flashed.
completely lost and no idea what to do.