htc 8125 question and help - 8125, K-JAM, P4300, MDA Vario General

Hi i have 2 part question my phone is an htc 8125 cingular sim card unlocked phone it has windows mobile 5 on it and i have the IPL 1.05, SPL.3.08 on it.
I did this but installing the IPL_SPL_3.08 rom. Anyways Im trying to get it back to IPL 1.05, and SPL 1.05 by installing the button rom and i seen the beer screen and it loads up to windows mobile 5 but keeps staying at IPL 1.05, and SPL 3.08 is there away to get it back to 1.05,1.05. I tried a few methods but aint working. Would keep reflashing a few times with the button roms get it back to 1.05,1.05. I tried with, newromupdateutility_wizard_noid. and didnt work i tried with rom update and didnt work. When a rom loads up and gets stuck at 99% and then i get a message with activesync saying lost communication error message whats does that mean and it saying try restore.
Also can windows mobile 6 with touch flo install on this phone or no. I was tring to do that with but all i got was it going back to windows mobile 5 and doesnt upgrade to wm6. Do i first need it to get it back to 1.05,1.05 using the button rom then use ,lokiwiz02b to do the unlocking(mind you my phone is all ready sim unlocked). and then flash a t-mobile or cingualr rom and then do the update with a windows mobile6 rom.
Whats a good windows mobile 6 with touch flo that works good on this phone can u maybe post a link
thanks for the help

deleted for inaccurate information

First,you shud have CID unlocked the phone prior to upgrading to 3.08 bootloaders,cuz it becomes very difficult and frustrating to downgrade from 3.08 to 1.xx.Now the only way is to first try to downgrade to 2.xx by flashing the official carrier's rom and when completed downgrade to 1.xx through Button's 1.05.You can only CID unlock the phone,if its 1.xx,which you already know.
Secondly,it'll only upgrade to wm6 if its cid unlocked.Try to flash ipl/spl 3.08 again and make both ipl/spl 3.08 first and then downgrade to 2.xx by flashing the official stock rom,it might work.
Cheers!

Related

help with my imate kjam

hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
thanks for the help
7331ymerej said:
hi,
im a noob to this forum and pocket pcs and i think im doing something wrong but when i try to install mfrazzz's xda mobile 6 release 5 final. i its still the same old windows mobile 5
i think my cid is unlocked i followed the instructions given by farias thread.
how would i know if the cid is unlocked? i tried using mestrini's WST tool but i get an error.
thanks in advance
Click to expand...
Click to collapse
Always post vital data of the phone,untill it's not known which device you have,G3 or G4,it's hard to provide with any help.Post IPL SPL of your device.
If it's a G3 then its CID locked,you have not followed the correct unlocking procedure.Read the Guide and sticky by Dr.Puttingham and follow it correctly to CID unlock the phone.
If it's a G4,then you cannot straight away flash any Rom to it,to upgrade follow the method as Sticky 'SoftSPL or HardSPL' by equinox in G4 forum.
What error it gives while usung WST 4.2 Tool ?
Cheers !
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
7331ymerej said:
i have a g3, and the ipl: 1.01 (becuase i downgraded because the instructions told me to) SPL : 2.16
and the wst tool give me a "in the rexx script named : at line number :2840"
and is there a way i can change me ipl back to 2.16? cause nothing is working for me =/
thank you for your response
Click to expand...
Click to collapse
ok, you got ipl 1.01 cuz you downgraded with Button's Rom 1.05 but your spl remained unchanged 2.16,its nothing to worry about,it sometimes take a little more tries to downgrade spl to 1.01,flash the Button's Rom 1.05 a couple of more times to make both ipl/spl 1.xx,only then you can CID unlock the phone with lokiwiz 02b.Follow the guide for downgrading and unlocking at the below link and do the method correct.Your phone is still CID locked,untill you get your phone CID unlocked you can not upgrade to any wm6 Rom.
http://forum.xda-developers.com/showthread.php?t=285435
But if you want to go back to your original wm5 Official k-jam Rom and have ipl/spl 2.16,then Download official k-jam Rom 'K-JAM_WWE_216901_2169101_020710_ship.zip' from official website of i-mate k-jam or from the following link below:-
ftp://ftp.clubimate.com
1.unzip the Rom zipfile,get your phone into bootloaders screen (multicolored screen)by pressing and holding down the camera button and the Power ON button together,the phone will start in bootloaders(multicolored screen) it'll show you ipl 1.01/spl 2.16
2.when in bootloaders,connect your phone with pc via usb cable, a small usb written will appear at the bottom of the multicolored screen of your phone.confirm it.
3.open the unzipped folder of the downloaded Rom,run the RUU icon in it(double click Ruu.exe)
4. follow the instructions and flash the Rom,after completion,your phone will restart and start working.
Good luck !
thank you sooo soo much, im gonna try it again right now
i guess my phones SPL will not change. i must of flashed the ROM with buttons 1.05 about10 times but it still wont change .... oh well im just gonna go back to the stock rom my kjam is WEIRD haha
Please Help
Hello
I have the Kjam G3 (with IPL & SPL 2.16) & wm5. I want to upgrade to wm6.1 but the CID is locked. I tried the WST tools and followed the instructions to unlock the CID but nothing happened.
Please can any body help me to solve my problem and tell me any other way to unlock and where to download the wm6.1.
THANK YOU
READ the FAQs, they hold all of the answers that you need.

bricked...

Hello
Got here friends htc wizard (MDA VARIO). After dunno what only boot screen appears and thats all. Bootmanager is accessable.
IPL 1.01
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
I am able to put there button rom, but thats all. I tried many roms, but noone can be instaled. Also tried love wizard rom. I dont have the original rom.
Batery is loaded up to max.
Any suggestions?
Ok solved, it was problem with flash tool.
EDIT: still i dont have any functional ROM. The love wizard rom doesnt boot up. I dont have access to original rom. I am nearlly at end of ideas.
I was able to load there this ROM:
RUU_Vario_AKU3.3_3822_382120_026911_TMO_DE_GER_Ship.exe
But still it freezes on boot screen.
Please, anybody got a rom, that works in a Mda Vario from slovakia? Its for sure cid blocked and i dont have a functional rom.
Hard reset is not possible. He says, that failure at format. Any body got some idea????
maybe you can try to update your IPL to 3.08 and GSM to 2.x
sailor_sky said:
maybe you can try to update your IPL to 3.08 and GSM to 2.x
Click to expand...
Click to collapse
Tryed and still not working. But thanks for your post

HTC Touch not booting after trying CID unlock

i have rogers htc touch, after trying unlocking using ELF USPL , when i power on only see HTC Logo and then it goes off, i try loading new rom but still same problem . Please help
What is your IPL and SPL?
IPL is 2.21.0002
and
SPL 1.11.0000
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
michel-2000 said:
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
Click to expand...
Click to collapse
Thats a great tip to the community, I will refer back to your guide if I met with anyone with troubles using Rogers.
...thanks...
But, after reading a lot yesterday, seems that the USLP 3.14 is a ''battery eater''...
I'm testing it now..I will see in a couple of days if it is the case!
So far, it looks like it's using approx 2% of the battery per hour...
Definitely, you should always use 3.10.
I had a bad experience with 3.14, it takes up half of my battery after 5 hours of almost no usage.
i'm confused. .... i also have a rogers htc touch as well and i want to flash a custom rom onto it.
(my IPL: 2.21.0002 and SPL: 2.21.0000)
First, i know it has to be CID unlocked... using >> Elf 1.11 USPL ?
Can i use HARDspl ?? What is the difference between USPL and Hard uspl ??
Because i read something about ..... " HardSPL : This modified bootloader allows a much safer flashing process to take place since it reduces the chance of permenently bricking your device. It also removes the need to CID Unlock the device since it ALWAYS reports SuperCID when flashing. "
After a CID unlock and soft reset, the phone will reboot into the old ROM (Rogers, in my case) if i have not began flashing a new rom ??
Some advice please... thanks!
Use the guide written on 4th post.
Its located on this thread
Cheers.

IPL 3.14 makes my ELF battery dried after power-off?

I've been reading on the upgrade to 6.1 with various cooked rom, and decided to go with Tessa 4.5. Since it is required to go with IPL 3.10/SPL 3.10, i went from original ROM and upgrade one step at a time, to 1.17, 2.26 and 2.28, and 3.10 (both IPL and SPL). Then I noticed after 3.10, i cannot boot up. This is before I upgrade to Tessa, just upgrading IPL/SPL.
When in 2.26, everytime upgrade completed, reboot went fine. But after 3.10, it went wrong. I tried to fix it with upgrading IPL only to 3.14.
It still wont boot up after power down.
So I downgrade to IPL/SPL 2.28. The SPL went down, but IPL stays at 3.14, and the problem continues. I can upgrade to Onyx, but everytime I power down, i have to flash with IPL/SPL 2.28 to make the ELF boot up. When I get to the OS, i check my battery is 0%.
Is IPL 3.14 the culprit? If yes, how do I downgrade it? using elf-uspl and/or Rom Utility gives same result: IPL stays at 3.14.
Help?
Update:
i was able to flash with elf-uspl using ipl/spl 2.27/2.28.
Now i have onyx junior with the ipl/spl combination above.
But it is still having problem when I turned off the device. It won't go pass smart mobility, instead it just shut down again. I have to take out the battery, put it back in, then reflash with rom utility (with any spl/ipl below 3.0) then it would restart and go pass smart mobility and enter the OS.
What gives?
Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?
Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?
I finally settled with IPL/SPL 1.19 since this is the only setting that would still boot to OS after I Power Off the device. Now looking for Win 6.1 coked rom that would accept these IPL/SPL setting...
Update2:
After trying to downgrade and upgrade, I use the original HTC Touch ROM, Windows 6.0. Still the problem appear. So I decided to go with elf-uspl and get the SPL back to 1.11000 (which was the initial working setup). Then I flashed the IPL to 1.17002.
Now, with IPL 1.17002 and SPL 1.1100, everything went back to normal.
Is this mean I cannot use SPL above my initial setting? Obviously the newer cooked rom won't accept these number, as it needs to have 3.10 minimum?
I finally settled with IPL/SPL 1.19 since this is the only setting that would still boot to OS after I Power Off the device. Now looking for Win 6.1 cooked rom that would accept these IPL/SPL setting...

stuck on bootloader screen

Hi,
I have tried to flash a wiza200 that was already flashed with a manila rom, I checked that it is a G4. I used TNT.20273 Professional Wizard HTC Home FREE ROM, it seems to work , romupdate utility indicated that the device was flashed successfully but it reboots on bootloader screen. I tried to reflash it it gave the same result, I tried another rom but impossible to flash it with other roms. So I downloaded the official one from the operator O2 but I got "invalid vendor" message. I searched all the possible solutions but none of them worked( wizard love also). Is there a savior here ? someone who can give me the right procedure to follow.
initially the IPL was 2.21.0001 and spl 2.21 Olipr
now the IPL is 2.21.0001 and spl 2.21
Thanks
Best regards.
You must replace the Update.exe with a MaUpgradeUT_NoID.exe . Found here in Forum . Look in "Blue Angel" for it. Be sure that you flash the right ROM with it . It will no ask...

Categories

Resources