Related
I have a g4 8125 and tried to flash black diamond 2.0 using shelltool. I followed all the instructions, but I may have messed something up. I installed the enablerapi and certspcs files on my phone, but i realized later that i did this after turning off my radio. After flashing I made a hard reset, and now it just comes to the cingular splash screen and shows my ipl, spl, gsm and os (which it says is 6.0.0.0) and doesn't load anything. Anyone have any ideas? It won't connect to activesync either.
edit: sorry for my ignorance, thanks for the help though!
Please refrain from posting WITHOUT using the search bar. This question has been answered more than a million times.
For starters, hold down the camera + power button whil poking at the reset button
Hello there.
This is my first post, and I hopefully pray that I don´t get a "Please Do a search" kind of answer as I have been doing a hard search through the forum but haven´t found what I´m looking for. Probably I´m just using the wrong search terms but english is not my native language so I´m not sure how to look up for this issue.
First, I unlocked the sim of my device by sending it to a third party. Afther that, the phone came with a Wizard-Love OS installed, and finally I got excited and started to mess around with the Shelltool to get the device upgraded to WM6. (It´s a G4 by the way).
First I successfully upgraded to wm6 wee htc wizard v5.2.660, but then I found that the keyboard mapping was all wrong with the shown special characters (they weren´t where they were supposed to be at all), so i tried messing up with the registry trying to select a local language for spanish with no success at all....
Also I was having some issues trying to connect to internet via wi-fi even when I did get connected to the network, but did not test it hard enough.
Then I went farther trying to "shelltool" a Black Diamond 2.0 Touch rom, but then everything became a real mess... The Shelltool said that it was finish only like 4 to 5 minutes after starting so I disconected and Hard Reseted the unit. Don´t remember if I disabled the radio before flashing it, nor if I had the sd card installed on the device at the flashing momment, but definetly i had reinstalled the cert_spcs and EnableRapi cabs prior to this seccond attempt.
After the hard reset, it started but freezed on the first screen showing the ipl, spl, gsm and os (which it says is 6.0.0.0). Then I hard reset like two more times, with no luck. Then I entered on the bootloader mode, but after trying that for a while the phone stopped responding. It did not turn off, so I removed the battery. Then when I put the battery back the unit did not turn on at all. Even it did not show the charging red light when I connected it to the usb nor the wall ac adapter. I was devastated... I leaved the unit with the battery out all the night and the next day I reinstalled the battery to see that the device did turn on and did charge, but still it was locked on the splash window.
I tryed to reflash the unit using the bootloader under windows xp, after killing the activesync connection and using the wizard_Love_2.26.10.2_WEE_Novii_CF2 rom. The unit showed a progress bar so the pc and after 10-12 minutes it was done. I Hard reseted the unit but then it always started on the bootloader screen as if I was pressing the camera button.
Hard reseted, soft reseted, battery out and in, no luck. Then it went dead again. It did not turn on at all and no charging light. Once again i leaved the unit all day without battery and send it to the friend that had unlocked the sim for me. He just called me and told me that the unit was now up and running again with wizard_love rom. I´m really not sure how he did it. Probably i did something with the sd inserted when it was supposed to be out. I did flashed the wizard love on bootloader with the sd inserted but i´m not sure if that could have make the mess.
I would like to know if anyone have had this kind of lock up and how to deal with it (how much time to leave the battery out, etc). Also I will love to know how did my friend (he wont tell me as is it´s bussines and he charges for it) finally restarted my unit flashing wizard_love again, as I´m still too curious to not try to flash my unit again and probably be on the same mess once again.
Thanks in advance.
That's a lovely 1st post. If every one is to be like that.. it would be just to nice to help others.
Anyway, this may not sound logical, but I get problems with Shelltools when I do not have the official ROM flashed before another flash. What I would suggest is that, you ought to have an official ROM (check Wiki to download your official ROM flashing EXE), which seems to get me out of trouble a few times.
Also, it maybe wise to check your battery before any flashing attempt, make sure it is 100% (60% will do mostly, but in case of an emergency, that 40% helps). It cases where a phone doesn't go charge/bootloader, it is battery problem. The overnight thingy that you've done, probably rest the battery long enough to boost it to a charge (e.g. how you get a blink when you switch off a torchlight for period of time on a low batt).
Good also among your information, tell us the IPL/SPL/Radio on the ROM you are using.
Hi, I would really appreciate anyones help with this. My brother went on holiday and left me his 02 XDA Mini S (I found out here its also called a Wizard?), and I had no problems using it for about 3 days - was just testing the various features.
I found my brothers contacts - and since its now a hand me down so I wanted to remove all these etc - I asked my brother what to do and he said do a Hard Reset. I found out in the Manual how to do it - I press the Communication Button and the voice command button and use the reset and nothing happened. I asked my brother and he said use the communication and voice button and then turn it on, that sometimes works - and it did. The screen showed:
Press Send to restore factory default...
I pressed the send button and it said it formatted. I was happy, it turned on, I did the set up - everything was working. Then at the end of the day I turned it off and in the morning I turned it on - all the screen shows now is the screen which first comes on - 02 with and underwater bubbles thing, and four lines -
IPL 2.21.0001
SPL 2.21.0001
GSM 02.07.10
OS 2.21.4.1
in red.
It won't go to the next screen - which I think says windows mobile. It just stays at the first screen when I turn it on - and has these four lines
Can anyone help me please? My brother will be back from holiday soon and he will be very upset with me if he finds I ruined his phone
please please please help me - i'm not as good with technology as you guys
Jocelyn
Try and get into bootloader mode by holding down the camera button and soft resetting your device. From bootloader mode you can flash back to the factory rom that was on the phone or wizard love.
Hi
I found how to go into Bootloader mode - my phone now shows three colours. But I'm not sure how to do the rest you mentioned. Could you explain how I should do it step by step please? Sorry!
Jocelyn
He means that you download the orginal rom from your provider and flash it back onto the phone.
Ok
I have made no progress
Here's what I did (please don't laugh - I'm new at all this)
1. I downloaded the active sync software from microsoft, and also downloaded a file i searched through on the forum mentioned by peter, called Wizard Love.
2. I pressed the camera button and soft rest the wizard to go into boot mode
3. I ran active sync - it said no connection.I connected the Wizard and searched - it said that no device was found (but the computer made a sound like it always makes when USB is plugged in). Also on the phone, it showed the word USB at the bottom left of the screen.
4. I extracted the wizard love and double clicked on the file newromupdateutility_wizard_noid.exe
5. When I got to the screen about existing software on the phone it was blank in that section, but it had the option to use the new one, so I proceeded.
6. The Wizard screen switched to a bar and completed 100% within about 5 minutes. Same thing on the computer screen.
7. It shows congratulations - etc.
8. I clossed everything and shut off the computer. Disconnected the wizard and there was a picture like some love cartoon characters - and thats all.it just stayed at that screen for a long time. Finally i thot maybe i should turn it off, but the power button does not work.
9. I used the stylus and did it a soft reset - the phone still froze at the start, with a wizard love cartoon - but the 4 lines i mentioned in my first post were different - it showed different numbers. But it still stuck there.
10. I thought maybe the wizard love is not compatible with my phone? So I went to the 02 XDA mini site, and downloaded the software from there - Xda_Minis_Upgrade_v2.21.4.101. I redid the whole thing, this time with this software.
11. At the end I saw Congratulations! again, but this time the screen had gone back to 02 - and the numbers went back to what was in my original posting. But still the phone does not start - its just stuck at that 02 screen with the 4 red lines.
12. Somone help me please!!! Have I made it worse???
Jocelyn
The Love ROM should work on your phone since it it does not have IPL/SPL (AFAIKnow). However, it seems that the phone itself already have a bit of problem itself. Using the "Xda_Minis_Upgrade_v2.21.4.101" to flash the phone in bootloader mode is the wise thing to do. Probably you'll need to hardreset it again (i.e. what you've done in the very first post).
As far as I can see, you've did nothing wrong on your first post. It seems to be the phone problem. ANYWAY, you may want to note the little issues. Example, do not have the miniSD card in the phone when doing all the stuff said above.. and possible, remove the SIM as well.
Also, sometimes, it takes ages for it to boot up. I'm not sure how long you've waited, but I would say.. give it a good 5 mins to do its bootup to confirm it hanged.
Sorry
I should have mentioned - in both cases when I ran the utility, once I waited at the splash screen for more than 10 minutes and nothing happened, i just tried to do a hard reset. In both cases the words came up, press send to do a reset etc...
but when I press the left (green phone) button (i think that is the send button?) it says format failed everytime.
I searched at some other thread and followed what Zabardast_1 says about flashing and I tried that, it does not work. Is there any other option? Oh i also tried it another time, this time disabling Anti Virus first - but still no luck
Jocelyn
Hmm.. I'm sorry to tell you. Since you have a 'Format fail', you 'officially' have a bricked device. That has something to do with the hardware.. or stuff that doesnt have any thing to do with your flashing.. probably CID unlocking may cause this problem.
ANYWAY, it seems that your only choice is to get it to somewhere to have it fixed. probably you want to make it as official (i.e. use the O2 ROM) before taking it to O2 to have it fixed.
Hi Everyone,
I'm having some issues with my P3600.
Sometimes (to many times in the past days) while making something on it, the image on the screen suddenly mess up (freezes and weird image) and hangs. Then after the soft reset, somethimes the image stays black, and finally on the 5\6 try it boots fine...
Also noticed that this occurs more while connecting the usb cable jack to sync...
Already make some hardresets and some rom upgrade tests... Also tryed some wm61 cooked rooms, no luck.
Anyone already got this? I think there's must be some problem on the flat cable that connects the lcd-board. Can anyone help me whit some more ideas... before I decide to open it?
Thanks In advantage
SteelwarrioR
it happens the same to me... the pixels all messed up... i dont know wath is the problembut i think its the flat cable ... becouse i have open it one time 3months ago and now its fine. now yesterday have done the same thing
sorry my english
Ok, I open it last night based on the service manual I found somewhere on the Internet, the flat cable looks fine... Now this morning this same situation occurred again, this time while unplugging the usb charger. I Think there's must be some problem on the usb connector. The usb connector is part of the main board so it could be a hardware board issue? Anyone got this on problem on Trinity? Any troubleshooting tips ideas will be appreciated...
SteelwarrioR
hi,
same here. trinity hangs up after some time, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts. I already changed the simcard and removed the sd-storagecard.
The vodafone hotline adwised me to send it in. Seems to me like a hardware issue.
My trin is about 1 year old.
(sry for my bad english)
Andi
No solution Yet???????
hi,
same here. trinity hangs abouth 3 or 4 time a day, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts
hi, the same to me... it's like the rom's, after a few soft reset couldn't find the necessary files to start again.... and sometimes, after meny tries, it starts well... it's like the ppc processor gets tired and goes to stand by..... it starts freezing the display, and loosing some pixels. so the only things to do is soft resetting the device... any solution? thanks
same with my htc - it appears to me that the errors occur when the trinity was used for a while and the processor was getting warm. the files and folders on the sd-card show strange symbols. but i have also problems when i stick out the sd-card completely.
i will send it to htc repair center - i just hope that they will not send it back as the errors occur only frequently.
so long,
bjoern
solution solved
take taste power and center ok reset take few sec to powering and phone starting
or power and run and stop call reset and phone starting on factory powering
not solved at all
sorry no - this is not the point - i think all guys here have (hard- and soft-) reset their Trinity more than 50x!
the problem is that once the software has crashed you can`t reset it for about 20min - it seems that the processor has to cool down or something like that - after a while (if I´m lucky) my P3600 boots as normal.
I already flashed several new roms - same problem with all of them - I`m pretty sure it`s a hardware failure.
Hello, i don't have any such problem, my Trinity runs very stable even with cooked roms. but sometimes Mobile navigator 7 takes too much memory so the System becomes instable and i have to softreset it.
Hi, mine bug also, and that's begin 2 or 3 days after I have flash to the 1.56.70.11 Radio Rom....
mine worked fine for about 1 1/2 years but suddenly it crashed continous. i havent flashed it and allready hard reseted several times on different days. sometimes it worked for a while but hangs if i started a bigger app like tomtom. vodafone told me they will exchange my p3600. now im waiting for their call
E: Got a new one today which works perfectly so far!
Hi guys,
has anyone had this issue solved without swapping the device?
I have the same problem.....
Bye
Petz
Same problem here...
I have to sftreset or hard reset several times to get it runing again...
In my opinion its some kind of problem with the processor...
Stiil i'm hoping this is a software insue... so that sone one have a hotfix for that...
For my part, when my Trinity crash, I remove the mini-SD, the SIM card and the battery. I just re put the battery, restart (soft reset until WM has realy start, and no more touch or screen freezes), I replace the sim, restart again.. and finaly I replace the mini-sd. It's very long, but generally works well
EDIT:
Finally, I better make my tongue and keep my method for me because at evening begin, my trinity crashed and impossible to turn it on until I finally come back house and have no need more...
my hand that it will crash tomorow morning juste after leave to works
hi, i started getting the same problem.
only thing different is I upgraded to wm6.1 (Mary SL)
I took it back to wm6 which was still locking, then down to wm5.
1week later no issue!
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
just a thought!
xpuser8334 said:
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
Click to expand...
Click to collapse
I don't think so because I downgraded my Trinity to original WM5 and, even if there were less crashes, it crashed anyway.
Now it's still with WM5 but it doesn't start anymore, only backlight.
Ciao
Petz
I want to let you known that my Trinity has run ok for 5 hours without any issue after putting some paper between battery and metallic plate under the battery.
I had to press a little over the rear cover to have it placed correctly because the battery is higher than before.
Keep in mind that it stopped running completely 3 monthes ago, it didn't start anymore and it didn't even go into bootloader mode.
Now I'm using WinMobile 6.5 beta........
Ciao!
Petz
Hi Guys , i have Trinity P3600 in Egypt ,,, it worked perfectly for more than 2 years , but last month it make the same problem like mentioned b4 , hangs , stuck in boot image , or mess in pixel ,,, and i tried to downgrade but no luck, i tried to use different Radio ,, it works sometime , but after a week no , i tried to take out the battery and wait for 3 hours , then back again , so it works but again it hangs if i start my GPS (IGO8) or heavy programs/.
any solution pls
Thanks
Hi,
I bought HTC HD2 TMOBILE from ebay and got it delivered yesterday. When i checked the phone it was working fine and it was a locked piece. Today morning i got the unlock code and the phone started working fine. I was just going through the features and checked the setting and stuff. Suddenly in 15-20 mins the phone restarted itself to the white pink screen of stick together. I thought its normal and gave it like 10-15mins to boot. Nothing happened. Had to take off the battery and tried booting it n still no response. I did a hard reset. Still the white n pink screen forced me to see the lame stick together msg. after a few resets the phones booted up and gave me the windows first time usage screen. I set it up and then bam! again it restarted to the stick together screen. i noticed tht it doesnt even shows the rom etc etc info on tht screen like it used to the first time.
Steps i have already tried...and none worked
1) hard reset
2) soft reset
3) reset with no sim mem card
4) flash tmobile latest rom from their own website ( tht screwed things even more as update failed at 8% and then the stick together screen disappeared and SOFTWARE UPDATE FAILED screen poped up )
5) Tried the HSPL3 to changed it to 2.08 HSPL ( tht got the stick together screen and nothing else )
6) flashed custom rom ( after multiple attempts it allowed me to complete update and after successful update the stick together screen appeared )
7) now i have reverted back to 2.08 thru hspl3. got back the stick together screen.
What can be done and why did this happen when i was just checking the settings?
IMPORTANTLY how can i fix this...
Check the battery contacts. My friend had a similar thing where only the wirth boot screen showed and it ended up being the battery contacts.
jaszek said:
Check the battery contacts. My friend had a similar thing where only the wirth boot screen showed and it ended up being the battery contacts.
Click to expand...
Click to collapse
+1
This is a very common occurence on this phone...the little gold pins get bent easily and the constant rebooting is one of the main symptoms when that happens.
hmmmmmmmmmm i will try tht now... was keeping myself away from it as it has already eaten up half of my only holiday in this week...
you are a genius
my girlfriend thought she bricked her phone cuz it was stuck on the stick together screen......see was about to try to flash thr original stock rom when i happened upon this post and it saved us alot of time ......so i just want to say thank you so much
Hi i have an s4 i9505.
It was bought from someone else so i cant go back to the store so i hope some people here can help me.
I flashed a GE rom on the phone and it got random reboots so i reflashed it to stock. It worked for 2 days and did a lot of reboots to test if it keept working. After those 2 days i wanted to insert another sim so i first rebooted to check if it still worked and it dit then i turned it off. I inserted the new sim (witch requires to pull the battery). I tried to boot it and it came to the unlock screen and even before i touched it it rebooted. It was stuck in this reboot loop.
The weird thing is that the more reboots toke place the shorter they took to get to a reboot. So the first time i got to lock screen after 2 times i didn't. Better said after 20 reboots it even rebooted in the startup sound. Now if i plug battery insert it again it does the same. If i leave the battery out for some time and put it back in it will boot again to lock screen (sometimes i can use it for 5 min before a reboot).
I already had done a new flash of stock firmware and also flashed cm10.2, cm11, GE4.4 and some more roms they all have the same problem.
I already replaced battery and didn't help a bit.
I hope someone can help me and give me a direction i have to look into.
zeldalink said:
Hi i have an s4 i9505.
It was bought from someone else so i cant go back to the store so i hope some people here can help me.
I flashed a GE rom on the phone and it got random reboots so i reflashed it to stock. It worked for 2 days and did a lot of reboots to test if it keept working. After those 2 days i wanted to insert another sim so i first rebooted to check if it still worked and it dit then i turned it off. I inserted the new sim (witch requires to pull the battery). I tried to boot it and it came to the unlock screen and even before i touched it it rebooted. It was stuck in this reboot loop.
The weird thing is that the more reboots toke place the shorter they took to get to a reboot. So the first time i got to lock screen after 2 times i didn't. Better said after 20 reboots it even rebooted in the startup sound. Now if i plug battery insert it again it does the same. If i leave the battery out for some time and put it back in it will boot again to lock screen (sometimes i can use it for 5 min before a reboot).
I already had done a new flash of stock firmware and also flashed cm10.2, cm11, GE4.4 and some more roms they all have the same problem.
I already replaced battery and didn't help a bit.
I hope someone can help me and give me a direction i have to look into.
Click to expand...
Click to collapse
How about the connector pins on the battery? Does one of them look like it's bent in so that it might not be making good contact all the time?
Do a factory reset and install my real AOSP http://forum.xda-developers.com/showthread.php?t=2397511, it will solve your problems guaranteed
broodplank1337 said:
Do a factory reset and install my real AOSP http://forum.xda-developers.com/showthread.php?t=2397511, it will solve your problems guaranteed
Click to expand...
Click to collapse
it was already on there and even at that rom it keeps randomly rebooting (mostly in the bootup sequence)
Skipjacks said:
How about the connector pins on the battery? Does one of them look like it's bent in so that it might not be making good contact all the time?
Click to expand...
Click to collapse
the battery pins look al good.
okay the problem is resolved for now i replaced the battery again with another one and that one still works even after a few reboots and battery pulls the other 2 batterys are both dead so thanks for all the help