Please Help-Wizard Won't Boot After Flashing - 8125, K-JAM, P4300, MDA Vario General

I have a g4 8125 and tried to flash black diamond 2.0 using shelltool. I followed all the instructions, but I may have messed something up. I installed the enablerapi and certspcs files on my phone, but i realized later that i did this after turning off my radio. After flashing I made a hard reset, and now it just comes to the cingular splash screen and shows my ipl, spl, gsm and os (which it says is 6.0.0.0) and doesn't load anything. Anyone have any ideas? It won't connect to activesync either.
edit: sorry for my ignorance, thanks for the help though!

Please refrain from posting WITHOUT using the search bar. This question has been answered more than a million times.
For starters, hold down the camera + power button whil poking at the reset button

Hello there.
This is my first post, and I hopefully pray that I don´t get a "Please Do a search" kind of answer as I have been doing a hard search through the forum but haven´t found what I´m looking for. Probably I´m just using the wrong search terms but english is not my native language so I´m not sure how to look up for this issue.
First, I unlocked the sim of my device by sending it to a third party. Afther that, the phone came with a Wizard-Love OS installed, and finally I got excited and started to mess around with the Shelltool to get the device upgraded to WM6. (It´s a G4 by the way).
First I successfully upgraded to wm6 wee htc wizard v5.2.660, but then I found that the keyboard mapping was all wrong with the shown special characters (they weren´t where they were supposed to be at all), so i tried messing up with the registry trying to select a local language for spanish with no success at all....
Also I was having some issues trying to connect to internet via wi-fi even when I did get connected to the network, but did not test it hard enough.
Then I went farther trying to "shelltool" a Black Diamond 2.0 Touch rom, but then everything became a real mess... The Shelltool said that it was finish only like 4 to 5 minutes after starting so I disconected and Hard Reseted the unit. Don´t remember if I disabled the radio before flashing it, nor if I had the sd card installed on the device at the flashing momment, but definetly i had reinstalled the cert_spcs and EnableRapi cabs prior to this seccond attempt.
After the hard reset, it started but freezed on the first screen showing the ipl, spl, gsm and os (which it says is 6.0.0.0). Then I hard reset like two more times, with no luck. Then I entered on the bootloader mode, but after trying that for a while the phone stopped responding. It did not turn off, so I removed the battery. Then when I put the battery back the unit did not turn on at all. Even it did not show the charging red light when I connected it to the usb nor the wall ac adapter. I was devastated... I leaved the unit with the battery out all the night and the next day I reinstalled the battery to see that the device did turn on and did charge, but still it was locked on the splash window.
I tryed to reflash the unit using the bootloader under windows xp, after killing the activesync connection and using the wizard_Love_2.26.10.2_WEE_Novii_CF2 rom. The unit showed a progress bar so the pc and after 10-12 minutes it was done. I Hard reseted the unit but then it always started on the bootloader screen as if I was pressing the camera button.
Hard reseted, soft reseted, battery out and in, no luck. Then it went dead again. It did not turn on at all and no charging light. Once again i leaved the unit all day without battery and send it to the friend that had unlocked the sim for me. He just called me and told me that the unit was now up and running again with wizard_love rom. I´m really not sure how he did it. Probably i did something with the sd inserted when it was supposed to be out. I did flashed the wizard love on bootloader with the sd inserted but i´m not sure if that could have make the mess.
I would like to know if anyone have had this kind of lock up and how to deal with it (how much time to leave the battery out, etc). Also I will love to know how did my friend (he wont tell me as is it´s bussines and he charges for it) finally restarted my unit flashing wizard_love again, as I´m still too curious to not try to flash my unit again and probably be on the same mess once again.
Thanks in advance.

That's a lovely 1st post. If every one is to be like that.. it would be just to nice to help others.
Anyway, this may not sound logical, but I get problems with Shelltools when I do not have the official ROM flashed before another flash. What I would suggest is that, you ought to have an official ROM (check Wiki to download your official ROM flashing EXE), which seems to get me out of trouble a few times.
Also, it maybe wise to check your battery before any flashing attempt, make sure it is 100% (60% will do mostly, but in case of an emergency, that 40% helps). It cases where a phone doesn't go charge/bootloader, it is battery problem. The overnight thingy that you've done, probably rest the battery long enough to boost it to a charge (e.g. how you get a blink when you switch off a torchlight for period of time on a low batt).
Good also among your information, tell us the IPL/SPL/Radio on the ROM you are using.

Related

XDA2 not playing ball.

Hi all,
Did a search on this, but hoping to prompt some new info on this.
While using my XDA2, running the latest WM5 from TofC via Buzzdev.net, with Tomtom it froze. Nothing too unusual with that, but this time the usual remedy of soft resetting it left it stuck at the splash screen. Same thing happend after removing the battery for a short while. I left the battery in, with it stuck at the splash screen, and the device became quite warm (as though it was working overtime).
Afterwards, I tried removig the battery again and then hard resetting. A couple of times, I have go it to boot MOSTLY, but the backlight will not come on (yep, I have checked the settings) and there are no sounds. Also, when it goes into stand-by, it wouldn't switch back on again.
I have since tried reflashing it with the WM5 rom (stuck at splash screen again), and flashing with the official O2 rom / radio (still stuck at splash screen).
From what I have read, it might be a battery problem, but I have tried charging the battery fully (in the cradle, not in the PDA) and nothing.
The battery I am using is a replcement from Ebay, the original is with a friend so not available for another few days.
Any fresh ideas most welcome!
Well, didn't expect too many replies :roll:
But academic anyway, because the 'brick' is fixed!!! After leaving the battery out overnight (not for the first time, I hasten to add) the XDA2 has decided to boot
It now has an XDA2s version on WM2003 (just thought I'd try it). Pretty sure though the issue wasn't ROM related, because it had been freezing at the same point with this new ROM.
So, anyone with the same problem on their device should not give up hope!

Wizard is Frozen - It won't start. Someone help pls??

Hi, I would really appreciate anyones help with this. My brother went on holiday and left me his 02 XDA Mini S (I found out here its also called a Wizard?), and I had no problems using it for about 3 days - was just testing the various features.
I found my brothers contacts - and since its now a hand me down so I wanted to remove all these etc - I asked my brother what to do and he said do a Hard Reset. I found out in the Manual how to do it - I press the Communication Button and the voice command button and use the reset and nothing happened. I asked my brother and he said use the communication and voice button and then turn it on, that sometimes works - and it did. The screen showed:
Press Send to restore factory default...
I pressed the send button and it said it formatted. I was happy, it turned on, I did the set up - everything was working. Then at the end of the day I turned it off and in the morning I turned it on - all the screen shows now is the screen which first comes on - 02 with and underwater bubbles thing, and four lines -
IPL 2.21.0001
SPL 2.21.0001
GSM 02.07.10
OS 2.21.4.1
in red.
It won't go to the next screen - which I think says windows mobile. It just stays at the first screen when I turn it on - and has these four lines
Can anyone help me please? My brother will be back from holiday soon and he will be very upset with me if he finds I ruined his phone
please please please help me - i'm not as good with technology as you guys
Jocelyn
Try and get into bootloader mode by holding down the camera button and soft resetting your device. From bootloader mode you can flash back to the factory rom that was on the phone or wizard love.
Hi
I found how to go into Bootloader mode - my phone now shows three colours. But I'm not sure how to do the rest you mentioned. Could you explain how I should do it step by step please? Sorry!
Jocelyn
He means that you download the orginal rom from your provider and flash it back onto the phone.
Ok
I have made no progress
Here's what I did (please don't laugh - I'm new at all this)
1. I downloaded the active sync software from microsoft, and also downloaded a file i searched through on the forum mentioned by peter, called Wizard Love.
2. I pressed the camera button and soft rest the wizard to go into boot mode
3. I ran active sync - it said no connection.I connected the Wizard and searched - it said that no device was found (but the computer made a sound like it always makes when USB is plugged in). Also on the phone, it showed the word USB at the bottom left of the screen.
4. I extracted the wizard love and double clicked on the file newromupdateutility_wizard_noid.exe
5. When I got to the screen about existing software on the phone it was blank in that section, but it had the option to use the new one, so I proceeded.
6. The Wizard screen switched to a bar and completed 100% within about 5 minutes. Same thing on the computer screen.
7. It shows congratulations - etc.
8. I clossed everything and shut off the computer. Disconnected the wizard and there was a picture like some love cartoon characters - and thats all.it just stayed at that screen for a long time. Finally i thot maybe i should turn it off, but the power button does not work.
9. I used the stylus and did it a soft reset - the phone still froze at the start, with a wizard love cartoon - but the 4 lines i mentioned in my first post were different - it showed different numbers. But it still stuck there.
10. I thought maybe the wizard love is not compatible with my phone? So I went to the 02 XDA mini site, and downloaded the software from there - Xda_Minis_Upgrade_v2.21.4.101. I redid the whole thing, this time with this software.
11. At the end I saw Congratulations! again, but this time the screen had gone back to 02 - and the numbers went back to what was in my original posting. But still the phone does not start - its just stuck at that 02 screen with the 4 red lines.
12. Somone help me please!!! Have I made it worse???
Jocelyn
The Love ROM should work on your phone since it it does not have IPL/SPL (AFAIKnow). However, it seems that the phone itself already have a bit of problem itself. Using the "Xda_Minis_Upgrade_v2.21.4.101" to flash the phone in bootloader mode is the wise thing to do. Probably you'll need to hardreset it again (i.e. what you've done in the very first post).
As far as I can see, you've did nothing wrong on your first post. It seems to be the phone problem. ANYWAY, you may want to note the little issues. Example, do not have the miniSD card in the phone when doing all the stuff said above.. and possible, remove the SIM as well.
Also, sometimes, it takes ages for it to boot up. I'm not sure how long you've waited, but I would say.. give it a good 5 mins to do its bootup to confirm it hanged.
Sorry
I should have mentioned - in both cases when I ran the utility, once I waited at the splash screen for more than 10 minutes and nothing happened, i just tried to do a hard reset. In both cases the words came up, press send to do a reset etc...
but when I press the left (green phone) button (i think that is the send button?) it says format failed everytime.
I searched at some other thread and followed what Zabardast_1 says about flashing and I tried that, it does not work. Is there any other option? Oh i also tried it another time, this time disabling Anti Virus first - but still no luck
Jocelyn
Hmm.. I'm sorry to tell you. Since you have a 'Format fail', you 'officially' have a bricked device. That has something to do with the hardware.. or stuff that doesnt have any thing to do with your flashing.. probably CID unlocking may cause this problem.
ANYWAY, it seems that your only choice is to get it to somewhere to have it fixed. probably you want to make it as official (i.e. use the O2 ROM) before taking it to O2 to have it fixed.

So i think ive bricked my iMate Jasjam but im not 100% sure spent hours reading...

Hey Guys,
Although this is my first post i have been reading and reading up about my iMate Jasjam and all of the other stuff that goes with it... Now whats happened is ive gotten this phone/pda for nothing with a sound issue that ive now fixed , it was running a rom with windows mobile 6.5. It was fine for almost 4 days but out of nowhere it wouldn't come out of idle or sleep mode where the screen is black and you just tap the power button to wake it. So i turned the phone off and on and managed to get it to boot into windows mobile but it froze, after this it wouldn;t go past teh load screen. I then removed memory card , battery and sim , still no boot afterwards... I then attempted to use the SD card to boot an original rom onto the phone but it comes up with "loading" for a few seconds and then just sits in the tricoloured screen and won;t budge.
Unfortunatly it appears the phones never had the hardspl done on it so if i can revive him ill definatly do this so it doesn't happen again... If i turn the phone on now it just hangs on the first load screen , ive still got GSM but im not very able with utilising the table to solve my problem... i was wondering if anyone could shed some light on the best way to try and revive it! it's a great little phone and i was using it heaps and heaps , had and did everything i wanted and would be such a shame to see it go as i got it for nothing, repaired it etc..
Thanks in advance and my appoligies if this is a stupid noob question.
Mick
You could try a hard reset, hold both "soft keys" (above windows and ok keys) while hitting reset, then the "R" on the slide out keyboard then space.
You should also be able to flash it from boot loader. Hold the power and side ok buttons while hitting reset, and you should end up in the tri colored boot loader, flash the at&t stripped rom from there (found in my sig below).
Then you can load hardspl. Then you should be ready for some flashing. Just make sure to flash the stripped rom between the custom cooked roms, it will straighten out odd memory issues (no need to let the stripped rom configure, it seems just flashing it is enough).
Welcome to the world of playing and bricking/unbricking your device!

I think I bricked it...

Before I start I know how touchy people are about searching forums and the wiki etc... but I already have!
Ok so, I tried to flash a new ROM to my phone last night, I have done it before without problems however this time I was having trouble getting the phone to connect to my laptop (I run Windows 7). Both USPL and HSPL wouldn't work (in fact active sync wouldn't even recognise it).
So I went to bed, woke up and... My phone didn't work at all
I spent ages trying to get it too work, I tried putting it into bootloader, but nothing happened, I tried getting it to Hard reset, but nothing happened. (By nothing happens i mean the screen doesn't turn on).
The only sign of life i get from it is the little vibration that usually occurs after the 'smart mobility' screen appears. Except this is delayed by about 10 seconds from after pressing the Power button.
The delay makes me think that there is something else wrong with the phone other then the screen...
Please help!!
Oh and I am sorry for the essay... I only just realised how long and rambling it is haaa.
UPDATE: right it just connected to activesync but still nothing on the screen, is there any way of checking for definite that the screen is broke before I fork out for a new one? There is astill the massive delay between turning the phone on and getting the little vibration...
Try removing battery overnight, then re-inserting. Then try to get to bootloader or hard reset
how exactly did you manage to brick it? did you flash the rom in question with uspl, or do u generally have hard spl installed? i dont know but it looks like the bootloader is somehow broken ...
Ok I will try doing that, thank you for helping
And no, I didnt get as far as flashing the ROM because active sync never recognised the phone in Bootlaoder. I usually use USPL.
Did you fix it? and if so how?
I have very similar issues with my HD right now. Screen went black, bought a new LCD and still the same problem. Oddly enough the only way I can get the screen to come on is to take the battery out and set both battery and phone body in my window sill for half an hour or so. It is cold here right now and they are both pretty cool to the touch when I take them out. Put it back together and tada! Screen comes on. I dunno what the deal is also, don't know if its the battery or phone being cold that makes it work again??? I am going to try and figure it out.. Try it on yours it may help

Stuck on "Quietly Brilliant" Screen

Hello.
First post here and hoping someone out there has a solution for my issue.
My HD2 gets stuck on the "quietly brilliant" screen every time I try to boot it. The only thing which happened directly before was that the battery was low and it switched off. This has happened before, but usually when I plug it in to charge it can just turn back on, or if not plugged in then tries to turn on but turns off again. The amber light comes on when it's plugged in to the charger, and it has been charged for enough time that it should turn on as normal.
I'm not as tech-minded as most of you so I'm kinda fumbling around trying to make something work.
I have tried:
Soft reset (multiple times, at different points in the loading (ie when it has the red writing bottom left before freezing, during "quietly brilliant" animation, and after freezing.
Turning on with memory card out.
Turning on with sim card out.
Turning on while plugged into charger.
Turning on when plugged into usb.
The phone will not:
Boot fully
register when plugged into PC
But it will enter bootloader mode (did I get the right terminology? With the Colour banding?)
When in this mode it either displays "Serial" or "USB" (if connected to PC)
I'm desperately trying to avoid a hard-reset as I've spent quite a long time manually entering contacts etc which aren't backed up (all would be lost ) and getting twitter/youtube/facebook all that jazz set up, along with programs and BSB tweaks, Dutty's task manager etc etc set up.
Have also spent time changing the theme with HDWall, and removing curtains/backgrounds etc with the TOUCH X tweaks. I've finally got my phone just how I want it...the biggest thing, of course is losing all of my contacts though.
I just have a HTC rom installed (can't remember what it was called, but nothing fancy, just the normal one to replace my TMobile rom).
Would really appreciate some advice/insight into what is going on and what I can do to sort it. Please help!
N
p.s. yes, I realise it was very stupid to not back up contacts...really really stupid. That will be the first thing I do once this is sorted!!
Oh and it won't turn off using the hang-up button when it's frozen-I have to remove the battery.
nudilover said:
p.s. yes, I realise it was very stupid to not back up contacts...really really stupid. That will be the first thing I do once this is sorted!!
Click to expand...
Click to collapse
If you use Exchange, all your contacts are stored in Exchange...which has the immediate benefit of backing them up, and the other benefit of making them sync with Outlook/OWA.
>: /
Hi there,
Thank you for your reply, I'll bear that in mind next time. But for now - how would I be able to check this? I'm really not sure if I set this up. Can I check it on my PC? I have Office 2007.
N
Ok...so I've found some of my contacts in my Outlook. Guess they weren't updated very recently but at least some are there. I can do a hard reset if I MUST...but please does anyone know of anything else I can try?
And if I leave it overnight is it best to leave it frozen/switched off/charging/battery out?
Will head off to bed soon as it's nearly midnight here and I've got work tomorrow.
N
Try to flash with another radio, you don´t miss your contacts if you do.
Some roms block with some radios.
hope it solves your problem
Ok, I'm going to try it. Found the old .nbh file and it was the 1.66 rom. So just trying to find the right radio one now. Thank you for the tip
Have tried 2 different Radio versions now and still sticks on the same screen on satrtup...is it hard reset time?
Feel like I'm speaking to myself here!! Ah well!...an update. DId a hard reset, and my lovely HD2 is alive and well (albeit looking far too "fresh out of the box"). While I'm at it with nothing back...is there a "better" standard ROM than 1.66 to be using? Anything newer? I'm never sure about these things.
Thanks for your patience and consideration guys...I'm a bit of a noob girl when it comes to these things!
Sound like you've installed a customized ROM. If its the case try to find out what is the best Radio for that ROM and re-install it.

Categories

Resources