Hey i don't know what happened to my Wizard but suddenly after installing two Alarm Clock softwares i just started losing my Screen Alignment. To fix it i even tried re flashing my Wizard but this time the problem started early and without installing those programs. Did anyone of you have the same problem?? If you do have a patch do post it in reply. Cause after using the ROM I'm using now all the other ROMs seem to be too Slow.
NOTE: Information about my Wizard is updated and in my signature.
Thanks in Advance.
HI,
Have you ckecked the connection between the screen and the print? Maybe it has a bed contact?
If you still have warranty, the you better send your phone back to let it repair
good luck
jordyk said:
HI,
Have you ckecked the connection between the screen and the print? Maybe it has a bed contact?
If you still have warranty, the you better send your phone back to let it repair
good luck
Click to expand...
Click to collapse
Hey im sure that there are no problem with the HARDWARE cause if there were problems with the hardware then it should not even work after i align screen and secondly if you know any ROM faster than mine (mentioned in my sign) cause when i switch to nayother ROM they seem to be too slow.
xda2_haseeb said:
Hey im sure that there are no problem with the HARDWARE cause if there were problems with the hardware then it should not even work after i align screen and secondly if you know any ROM faster than mine (mentioned in my sign) cause when i switch to nayother ROM they seem to be too slow.
Click to expand...
Click to collapse
hi,
but you said that you heve the problem with all the roms, isn't it? so then it must be a hardware problem?
xda2_haseeb said:
Hey im sure that there are no problem with the HARDWARE
Click to expand...
Click to collapse
Well there's your problem right there. Anyone that sure of anything can't be right about it.
Seriously though. This sounds like an intermittent fault, and that is the domain of hardware failures. This kind of thing happens when hardware ages. Especially around things with moving parts. That slide-out keyboard wreaks havoc on the ribbon over time, and eventually, they just give out. You may have one that's merely loose, or it may be getting ready to break, or it may already be broken and just touching often enough to make you think it's okay.
The chances of this being firmware or driver-related are really slim. If that was the case, the error would be constant, not intermittent.
Myrddin Wyllt said:
Well there's your problem right there. Anyone that sure of anything can't be right about it.
Seriously though. This sounds like an intermittent fault, and that is the domain of hardware failures. This kind of thing happens when hardware ages. Especially around things with moving parts. That slide-out keyboard wreaks havoc on the ribbon over time, and eventually, they just give out. You may have one that's merely loose, or it may be getting ready to break, or it may already be broken and just touching often enough to make you think it's okay.
The chances of this being firmware or driver-related are really slim. If that was the case, the error would be constant, not intermittent.
Click to expand...
Click to collapse
hey i guess that SLIM chance has won i installed another ROM (http://forum.xda-developers.com/showthread.php?t=367375) Its been a day and its working f9.
jordyk said:
hi,
but you said that you heve the problem with all the roms, isn't it? so then it must be a hardware problem?
Click to expand...
Click to collapse
Sorry! but i dont guess i said that anywhere by reflashing i meant reflashing the same ROM. If the problem still presists then it might be a HARDWARE fault but for now its working pretty fine.
Forgot one thing, if this is an HARDWARE issue then is it fixable?? if yes how?
hey man i had this annoying issue whenever i remove the battery..but it should be OK when u do alignment a couple of time repeatedly...try it and post the results here..
I have had alignment problems for a long time. Clearly mine is hardware related, since stock and custom ROMs both show the same problem. Sometimes I'll go for months with no problem, and then I'll have to start realigning several times a day. Thank god for smartskey, otherwise I could rarely close a program. I was told that it was probably a hardware problem and that it would've been covered under warranty (if I was still under warranty), but I never sent it off. Somebody else told me once that It was probably due to there being pressure put on the edges of the screen from the frame around the screen, and if I disassembled it, made sure the seal/padding wasn't touching the touch-sensitive part and then reassembled it, I should be fine. But I looked up the process in the service manual, and WOW it looked like a lot of work with a lot of places where I could screw up the phone, so I just live with it. Sometimes sliding it open and closed would totally mess it up. It seems to help if I just squeeze the edges of the screen to really "seat" it, and then align. Then it seems to stay pretty well aligned for a good while. Good luck!
I cooked up a ROM and installed it and it works now i dont have the problem. Please try my ROM and give me feedback link to it exists in my signature. Thanks. TC
Related
lately the touchscreen on my T-Mobile MDA sometimes stops responding, sometimes after slowing considerably. Up till now I have been able to get it going again after (several) soft resets, turning it on and off and fiddling around with it in general. There doesn't seem to be much of a pattern to it though.
Does anyone experience the same problem and/or know what might cause it and how to fix it?
Thanks!
Too many programs running? X doesn't close programs, it just minimises them.
Joost said:
lately the touchscreen on my T-Mobile MDA sometimes stops responding, sometimes after slowing considerably. Up till now I have been able to get it going again after (several) soft resets, turning it on and off and fiddling around with it in general. There doesn't seem to be much of a pattern to it though.
Does anyone experience the same problem and/or know what might cause it and how to fix it?
Thanks!
Click to expand...
Click to collapse
U need the file tpenable.exe (you will find it in external rom package)
U need the file tpenable.exe (you will find it in external rom package)[/quote]
I'll give that a try. I assume it will explain itself as to how to use it.
Thanks a lot!!!
27 said:
Too many programs running? X doesn't close programs, it just minimises them.
Click to expand...
Click to collapse
Nope. I checked and once or twice even a soft reset didn't fix the problem, so there weren't any programs running at the time. Thanks for the suggestion anyway, though; I'm pretty new at this XDA stuff, so you never know
Previous 2 entries were mine. Forgot to log in, sorry
Hi,
Man I know how frustating that is. I had a similar problem a few weeks ago where the touchpad only worked when I used my fingers, it didnt' respond to the stylus at all... I was *this* close to hard resetting or sending it in for repair, but a friend of mine suggested re-aligning the screen. Worked like a charm. Give it a try. I'm bogged down at work so I dont have time to look at where it was, but I think its in settings > screen somewhere.
Good luck!
Yesterday i cut a Screen Protector from an Ipaq hx 4700 to fit my Qtek S100, i cut it a little bigger so that it would fill the whole screen and be under the edges, what happened was that i couldn't tap anywhere, i did a Hard Reset thinking it was a bad configuration or something i did wrong, but the problem was the screen protector...i removed it and know it works just fine! I used Xbackup to restore my data and everything now is right!except i don't have a screen protector...
cyborg said:
Yesterday i cut a Screen Protector from an Ipaq hx 4700 to fit my Qtek S100, i cut it a little bigger so that it would fill the whole screen and be under the edges, what happened was that i couldn't tap anywhere, i did a Hard Reset thinking it was a bad configuration or something i did wrong, but the problem was the screen protector...i removed it and know it works just fine! I used Xbackup to restore my data and everything now is right!except i don't have a screen protector...
Click to expand...
Click to collapse
Yeah, I read about the screen protector issue before. That wouldn't explain why it is working fine most of the time in my case though. About your problem, the general consensus seems to be that the problem is the screen protector touching the sides. You could try again but cut it slightly smaller.
U need the file tpenable.exe (you will find it in external rom package)
Click to expand...
Click to collapse
What's for this one?
Minotavrs said:
Joost said:
lately the touchscreen on my T-Mobile MDA sometimes stops responding, sometimes after slowing considerably. Up till now I have been able to get it going again after (several) soft resets, turning it on and off and fiddling around with it in general. There doesn't seem to be much of a pattern to it though.
Does anyone experience the same problem and/or know what might cause it and how to fix it?
Thanks!
Click to expand...
Click to collapse
U need the file tpenable.exe (you will find it in external rom package)
Click to expand...
Click to collapse
I've tried running this on the device but it doesn't seem to do anything. What am I missing?
I've even removed the screen protector, but that didn't fix the problem either. Right now it is part of the screen (lower left) that is not responding. It's starting to get pretty annoying, but I'm reluctant to have T-mobile send the device off for repair. Since there's no fixed pattern to the problem I expect some repair guy is probably just going to hard-reset it anyway, try if it works for 5 seconds and send it back
Joost, let me know if you managed to resolve this... I have the same problem:
http://forum.xda-developers.com/viewtopic.php?t=18224
Will do, but it's not looking good. I can't seem to pin down a pattern, so it's hard to try and eliminate possible causes. I'm 99% certain it's a software problem; it comes and goes and I'm not even using a screen protector that might cause it. It seems to have something to do with calibration/alignment, because usually it's only part of the screen that becomes unresponsive (bottom left or bottom right mostly)...
As you can see (in the thread linked above), I managed to solve it -- it seems like there was a registry setting (in my case).
Did you ever manage to pin down what registry setting was responsible?
no, I didn't spend any time/energy on it -- but you can follow my steps if you want to try that route.
But I am not sure it is the same in your case, for mine it was constant after the ROM upgrade, not something that would come and go...
I think I've got it!!! Bad touch screen response (and general slowing of the device) seems to be related to weak/no network reception. Probably Windows Mobile gives priority to reestablishing network connection over some other processes, amongst which is screen response. This would be ok if the network routine only tries at intervals, freeing up time for other stuff inbetween, but it seems it just keeps trying continuously.
The way to solve this is probably to lower the priority of the network connection routine. So far, so good... Does anyone know if this can be done, for instance by changing a registry setting? If so, which one and what value?
Joost said:
cyborg said:
Yesterday i cut a Screen Protector from an Ipaq hx 4700 to fit my Qtek S100, i cut it a little bigger so that it would fill the whole screen and be under the edges, what happened was that i couldn't tap anywhere, i did a Hard Reset thinking it was a bad configuration or something i did wrong, but the problem was the screen protector...i removed it and know it works just fine! I used Xbackup to restore my data and everything now is right!except i don't have a screen protector...
Click to expand...
Click to collapse
Yeah, I read about the screen protector issue before. That wouldn't explain why it is working fine most of the time in my case though. About your problem, the general consensus seems to be that the problem is the screen protector touching the sides. You could try again but cut it slightly smaller.
Click to expand...
Click to collapse
I had the exact same problem of non-responsive touchscreen once i installed the protector which came with the device. After reading thro this thread, i slightly lifted the protector from the bottom edges and VOILAA!! the screen works again.
Strange problem this !!! Thanks for all the help.
Ok I searched and searched but couldn't find anyone with this same problem.
My screen flips out 10-12 times a day. What it look like is imagine a screen reflection in the water then throw a rock in the water. It distorts really bad. Anyone know if there is a fix for this or do I need to buy a new phone?
I'm running 2.26 Rom with my own custom extended rom and lots of programs, speed hacks and a2dp hacks, could some registry setting be doing this? a program?
ouch...sounds to me like you need a new phone. I'd try a hard reset, maybe a stock carrier rom and if that doesn't help, screw it, back it goes.
Its strange its not consistent and usually only on the today screen. I have hard reset the thing and re-flashed it multiple times. Think its slowly turning into a brick? Luckly $50 get me a new one with t-mobile if thats the case
"not consistent" is almost always a hardware problem. A trace somewhere corrodes and causes a resistance but not an open, heat affects a chip....all kinds of things can happen and it's not black and white. If $50 gets you a new one and you've already tried the obviously solutions, there's really no question what the next step should be. At least if it was mine. I'm already on my third phone in less than a year because of hardware problems.
Definitely a hardware problem.
Ahhh ok well. ok thanks for your help and thank god for spb backup
Mine has been doing this for ages... I hope it doesn't brick itself. I have backup and insurance too, thank god!
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
pod8 said:
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
Click to expand...
Click to collapse
Mmmm. Tricky perhaps. A hard reset will either cure or leave you stuck. If you hard reset and the screen is indeed dead (touch wise) then you'll never get past the alignment stage. If the touch issue is software related then you would be sorted with the hard reset.
A gamble I think!!
However you are stuck at the moment so in a sense you have nothing to lose. If it ends up being useless then you are faced with a warranty (hopefully) repair otherwise some DIY though it's not entirely obvious what has broken/come loose - possibly just a ribbon connector.
Mike
Maybe the ribbon cable came loose on the LCD side?
myztikal47 said:
Maybe the ribbon cable came loose on the LCD side?
Click to expand...
Click to collapse
Yeah i think its that as well, i hard reseted it a few times with no effect, in the begining of the day, it could still reconise the screen taps around 2/3 times before it totally went dead.
Are there any tutorials on how to open it up to check the ribbon?
Thanks.
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
myztikal47 said:
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
Click to expand...
Click to collapse
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
mikechannon said:
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
Click to expand...
Click to collapse
Ok my best bet is to take it to carphone, i got my screen replaced there a few months ago, think i still have a 1 year warrenty
Thanks for all your help anyways
Tytn Service manual
jblandon1024 said:
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
Click to expand...
Click to collapse
Here you can found the manual
http://www.megaupload.com/?d=0GD472TP
Roby
Hi Guys!
My TyTn is acting strangely. In use, the display is first pixelating, getting lines (noise pixels as well), and then fading to completely white. When so it doesn't responde to anything anymore. So a soft reset is needed.....
Also the ringtone when called, is 'out of tune', like a old record player when you push your finger on the record.. LOL
Before I send it back to have it fixed by HTC, do you guys have any idea whats wrong, and maybe even a tip to help me fix this myself?
Tried numerous soft resets, hard reset, and a reinstall of the original WM6 rom (in Dutch).
Did not install any new programs lately, or did change anything on the unit...
Don't want to miss my TyTn... so hate to send it away... as many of you I am hooked badly to my beloved digital companion
Greetzz Antal
It acts like hardware incompatible.
How about flashing with WM6 English version.
I don't think it is software problem.
I agree, not likely to be software. It did not get dropped or take a knock did it?
The two issues of pixelation/white screen may, if you are lucky, just be a connector thats loose. The sound I think is unrelated but again sounds like a poor connection at the white rear speaker connector block - not uncommon.
Both of the above could be caused by a sharp knock. There have also been cases of poor battery connections causing problems.
If you have a warranty use it. If not you can follow the dismantling guides or service manual to dismantle - check connections and re-assemble. Be prepared though, that sending it in might still be required!!
Mike
Will send it in
Hi Guys, Thanks fr your replies.
I will take the unit back to the store today.
I am not aware that I bumped it, or neither it has dropped. May be a connection that was allready quite loose to begin with. Lets see what HTC and the store will tell me
Strange thing is, that without my sim in it, and not using it, it stays normal... Have put it aside, and used a very old phone instead, and it is still normal..
Antal said:
Strange thing is, that without my sim in it, and not using it, it stays normal... Have put it aside, and used a very old phone instead, and it is still normal..
Click to expand...
Click to collapse
Mmmm... that's important information and changes things a bit. Could be a sim card contact or something about the sim. Anyway it tends to suggest that other thoughts about hardware issues may not be correct!
Hope you find the answer at the store.
Mike
http://www.youtube.com/watch?v=N8MmIErLhag
and my 2 videos showing the same problem.
http://www.youtube.com/watch?v=MVgFCV3boX4
http://www.youtube.com/watch?v=cFZhWS5jEik
Weird! Mine doesn't have this issue, I've tried the Notes line drawing test.
Neither do I..
Go get a replacement, it might be a faulty device. Not sure what's the point here. It is not a problem with the device, it's a problem with YOUR device.
To be fair mine did do it every once in a while, thought it was perhaps sumthing I had on my finger (oil/grease/water/sweat whatnot) however, desensitised the screen and popped a screen protector on it and it's 100% reliable now..
The first video is not mine so it is NOT my device problem and i tested on another hd2 and it made the same thing. That's why i came up with the touchscreen tweak you find on the tips and tweaks sticky but even that do not solve it 100%.
It has been confirmed has software problem like the pink camera here.
http://wmpoweruser.com/?p=10735
and original post
http://translate.google.pt/translat...htc.ru/2009/11/u-htc-hd2-eshhe-odna-problema/
the_ape said:
To be fair mine did do it every once in a while, thought it was perhaps sumthing I had on my finger (oil/grease/water/sweat whatnot) however, desensitised the screen and popped a screen protector on it and it's 100% reliable now..
Click to expand...
Click to collapse
that was my exact thought but with a screen protector i could make it do that so i quitted on it at the end.
Good to know i'm not alone here.
Same problem with mine, have applied the touchscreen tweak and aligned the screen which does make it a little better. Maybe the 1.48 rom will fix it and the camera when its officially released.
dude that is exactly what i got. its hard to write one word without the need to correct it. the keyboard is such a horror. it was easier to write on my diamond. im still thinking about to get money back, ask for a replacement or wait for an update.
Unfortunately rom 1.48 does not solve touchscreen problem nor camera pink issue.
So it's a hardware problem ?
adolfotregosa said:
Unfortunately rom 1.48 does not solve touchscreen problem nor camera pink issue.
Click to expand...
Click to collapse
Why don't you take your phone back and go get an iPhone instead? Complaining about it here isn't going to help any and it's not, as far as I can tell, a general issue as plenty of people do not see this effect (myself included).
just tried 2 of the tests on mine and i do not get any of the problems.
I just got an HD2 a couple of days ago on O2 in the UK. I have the stock 1.43 ROM at the moment and have this keyboard jitter really bad too . Should I ring O2 and get a replacement, or is a new ROM likely to fix it?
Cheers.