Database Users

[Q] Another touchscreen problem... Sorry..

I like MANY others has run into a problem with the touchscreen. Unfortunantly. So the story short:
1. Installed NAND + some ROM - Everything worked fine
2. After 2-3 months the touchscreen temporarily wouldn't react (on the lockscreen)
3. I did a total wiping of everything on the phone to original WM6.5 , then reinstalled MAGDLR and Android - It worked perfect for a day
4. The next day it didn't react, so i reinstalled as in 3. but it didn't work
5. I removed HSPL but I couldn't get rid of android - So I called the repaircenter and the dude I was talking to said that it didn't matter if i delivered it with android
6. It took a week to get it back - But they didn't fix the screen, they just left a note saying: "There have been unauthorized software on the phone. Therefore void all warranty and repair options"
7. I ordered a T5 Torx screwdriver, took a look inside the phone to check if it was a loose connection between touch screen and main board, but nothing seemed like it....
--- Now, this puts me in a weird position. Ordering a new DIGITIZER or both digitizer and LCD.. The LCD isn't damaged in any way, but I read that it's hard to install the digitizer only.
What would you guys recommend?
BTW, when I hold the power key in the start screen of android the upper option is being marked (Check picture) Is that an indication that the digitizer is ****ed?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(I apologize for the suckass quality of the picture)

Bump for help

get on an android build, and if you can get your touchscreen working, DO NOT TOUCH THE END KEY. for me, the end key causes all kinds of touchscreen problems. download extended controls or a similar app, and that will let you power off/reboot/go into sleep without touching the end key, then always use the green key/windows key/back key/home key to wake up and you should be good.
let me know if this work.

Thanks, I'll give it a try when I get home some time today

you are not the only one with touchscreen problems i had it
flash stock rom and send for repair
they changed the whole screen on mine phone, its not android issue its htc issue and the connection with digitizer and motherboard it breaks when pressing end button

forgot to mention only use my method if you don't have a warranty (like me) or don't want to send it in.

[Q] HTC desire hd broken.....

Hi happy new year i have desire hd bought from ebay broken im using it fo 2 weeks now as daily driver so soft is okey but hardwarly it has some broken parts the camera the headphone speaker and the speeker doesnt works.I havent yet give it to service so im asking you guy how hard can get this for repair:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

How hard to fix? Nothing to fix. Fixing such phones is replacing broken parts with new ones. Case is for replace (made of aluminium, expensive probably), camera module probably for replace (it's all in one assembled together), camera led seems to be for replace too. Replacing that all is 30minutes and pretty easy. Look for parts prices on net.

Well I went to a HTC service in my city and they tell Me that they have to change all motherboard if I want to fix it and that will cost me as much as new phone and they have to do it cuz my phone is bougth from from another countrey and the don't have the software for fixing it so I'm stucked.
Sent from my Desire HD using XDA App

Whoever told you that is a moron. If the phone is booting the motherboard is fine. What they have to replace is the volume button ribbon cable assembly. It has the board that the camera and speaker/headphone jack is mounted on. that part is about $40 USD. The camera is about 15 USD and the back casing is about $50 USD. And why would they need software to replace a flex cable assembly. Don't do business with them.

Does it all work fine?
replacement LED flash lens covers and Rear battery covers are very cheap to buy
there are many videos on youtube "Desire Hd Disassembly" that tell you how to open it up, its just a few screws to remove the back cover,
main problem with opening the dhd is the warranty void stickers and to get to two of the screws you need to remove the sticker near the battery that has your IMEI/ serial on it, and its hard to stick back on

[Q] Part of touchscreen dead

Hi,
A part of the touchscreen of my milestone suddenly become unresponsive.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If i press inside the red area (including home button) it wont work and its just like i pressed the near side, like icons in the left or right of that red area.
I tried full data wipe, cache and dalvik, tried flashing newer sbf and no good.
Do you guys have any idea on it?
Thanks

Bad news bro.
I'm pretty sure its a hardware problem, the screen must be damaged...

So i need to replace it?

e7zip said:
So i need to replace it?
Click to expand...
Click to collapse
Better to get a new phone =D

a new phone is your option coz replacing the screen would cost you alot while you can get a better phone in a few bucks more!

New screens are available on amazon for 12 pounds (at least I spend this much)
However It may be a signal cable. They starts from 30$ on ebay

There are disassembly videos on Youtube.
I had a similar problem and I did the replacement two months ago and it works.
I bought the screen digitizer with tools on eBay.
Be sure That you have a torx3 beca use it didn't came on the tools! ;P

I had the same problem... I sent to the Moto Assistance and the had to change the touchscreen for a now one.
Good luck!

Not the cable. If the cable was damaged, it would shut down the entire screen. It's a problem with the digitizer. Hopefully for you it's relatively easy to exchange it, but you'll damage the camera sticker, the top panel of back side, above the battery and the speaker grid sticker (all of those are glued to the phone) in order to open it. Doesn't matter the way you take them over, you'll always damage it. Might wanna buy some of these on ebay too, although I'm not sure they sell it.
I had the exact same problem with my first M2, it was still under warranty but Moto took sweet 15 days to exchange it, and they returned my phone with a stuck volume rocker. Had to send it again, they took more than 15 days this time, so I asked for a replacement.
M3 XT860
DarkDroid 1.1 (Unsafe) + Hash's ICS Beta 1 (Safe)

Pixel Discoloration Possible Flex Cable Issue

Hi All,
I just replaced my Nexus 7 screen for the second and last time. First time went without a hitch everything worked great. This time everything went without a hitch until I booted the tablet on with the new LCD/Digitizer assembly. The touch on this screen works, but I am getting some discolored pixels and a line in the middle of the screen that runs up and down if you are holding the tablet vertically. Pictures are attached of the phenomena. I read on ifixit it might be the Flex cable as someone described pretty much the same scenario and replaced the flex cable and got it working. Below is the quote from Ifixit.com If anyone has any insight about this issue that would be much appreciated. It is bearable to use. I really do not think its the assembly itself but rather something else like the flex cable which was not replaced new when I reinstalled it. I am still using the same cable from factory. Also the screen displays a lot of things with perfect resolution and the pixel discoloration seems to move from spot to spot and not stay in one location as dead pixels would behave. Thanks again in advance.
"I bought the LCD/digitizer on Ebay, the UK sellers are the cheapest.
After some forth and back mailing (the wrong address was used so the screen was shipped twice) I received it. The disassembly went smoothly although it took me a while to find out that the flat cables were locked in place with a retaining tab. Therefore I busted the data display cable. The screen came up in two halves, lots of snow, yellow or red. After straightening the display cable the screen was perfect but bending the cable back in place brought back the snow and discolorisation. For 10 Euro a new cable (also Ebay) and it works like a charm. Total cost 85 euro, 75 for the screen and 10 for the display cable.
Thanks for the guide."
Click to expand...
Click to collapse
-From Ifixit User
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

problem with android unit

good afternoon
i have some problems with my Android system
my system is https://www.aliexpress.com/item/32995598640.html?spm=a2g0s.9042311.0.0.3c614c4ds5xGgH 8.1 oreo 4g 64gb top version
I bought it 2 years ago .
10 days ago i would like to clean. I get it out i clean it (dry). when i go to put it back i decide to put it whith out the cabletape 60p 0.5mm which connect the screen.
when i was going to put the cabletape it was burning . i buy new cabletape and then the screen is oppening too too too light for a second and it make restart all tme . i chose to make reset with the button on the screen but it do the same ...
have anybody a resolve or whats happen to the divice..
Thanks so much
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

if someone know a thecnical engineering in Europe ?

?

!

plz

plz

good afternoon
i have some problems with my Android system
my system is https://www.aliexpress.com/item/32995598640.html?spm=a2g0s.9042311.0.0.3c614c4ds5xGgH 8.1 oreo 4g 64gb top version
I bought it 2 years ago .
10 days ago i would like to clean. I get it out i clean it (dry). when i go to put it back i decide to put it whith out the cabletape 60p 0.5mm which connect the screen.
when i was going to put the cabletape it was burning . i buy new cabletape and then the screen is oppening too too too light for a second and it make restart all tme . i chose to make reset with the button on the screen but it do the same ...
have anybody a resolve or whats happen to the divice..
Thanks so much

In reality, you aren't going to get a reply because nobody has a clue what you've done. Post a video up of the failure and perhaps you might get a response, but in reality, you've done something right weird here, haven't you? I mean, who cleans their head unit.... just wipe the screen and be done with it.
Did you plug the old ribbon connector in while the unit was switched on? If so, my best guess is you've shorted something which is why your ribbon cable melted. Potentially what you've goosed as a result.... is a mystery.
Could be the entire screen, could be the entire unit, could be neither...
Might be time for a new one.

Might be time to find a local electronic repairer.