Database Users

help me!!!!! please i can`t start my P3300

anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..

hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?

it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?

dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...

Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.

arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks

Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?

MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?

Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan

ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403

USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!

same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz

well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work

y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too

Cincular 8525 stuck in Bootloader

I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?

Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help

Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!

Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.

1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......

Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time

Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.

Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol

Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up

I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks

need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas

kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...

Newbie: cannot install Hard SPL for love nor money help!!!

Before anyone ask's I have read all the posts regarding installing the Hard SPL but still have the same problem.
When I connect through Vista 32 via WMDC it recognizes my device fine, I then follow the steps in the tutorials but as soon as I press the button to update the ROM image it goes into the 3 colour screen and then into the updating ROM progress bar were it sits at 0% for ever.
My WMDC has disconnected at this stage and then I get a screen saying communication error which is obvious as WMDC has disconnected.
Is this a WMDC issue/ Vista or am I missing something
I then have to soft reset and it just re boots into my standard ROM.
Any advice woiuld be greatly appreciated

hello
1) connect your polaris to PC
2) run update utility
3) when you see 3 color screen unplug USB and replug it immediately
4) your SPL flash may start
5) when flash end correctely your polaris reboot
6) Flash any ROM you want

Thanks for the quick reply.
Tried doing exactly as you have stated.
Unplug and reconnect in the 3 colour bar screen, after which it goes into the updating screen and sits at 0% for ages until communication error comes up.
My WMDC has disconnected and does not reconnect.
I'm at my wits end!!

Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.

Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
I think hard-spl can not be installed with sdcard method!

Why not ??? With Trinity you can do it.

cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers

batista70 said:
Why not ??? With Trinity you can do it.
Click to expand...
Click to collapse
But this is not Trinity...Try it...
I know You can flash polaris if you use jumpspl (this is used by hard-spl flash) or hard-spl (this is used by os and radio flash).
But if you have original spl on you pda, and you want to flash with sd card, you will not use nor jumpspl neither hard-spl.

mikee5402 said:
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
Click to expand...
Click to collapse
hi there.
try to hard spl with your sd card not in the device.
go in to bootloader mode (BL mode - by pressing down the Camera button, then using the stylus, press and hold the RESET button at the bottom of the phone and release when tricolor screen appears),
now connect the device to your pc (it should show usb in the white part)
flash what you may... hard spl first, oli's recomended by me.

ItayE,
Did you try the hard-spl flash with sd method? Does it work?

I didn't read it was Vista compliant so I ran it from a windows XP SP2 machine with Active Sync 4.5.
I did mine by taking out the SIM card and the SD Card then resettting and running the HardSPL.
HTH
Leon

Cheers for the advice guys I have managed to do it.
I used the Hard-SPL-V2 first which worked fine then I flashed to one of A.Serg roms, very nice and quick it is too.
However my reception bars are down to 2 from 4 that I previously had, although the reception seems ok.
Sim: O2 UK
Rom: 1.52.ASerg.4 WWE
The radio version I have is: 1.58.25.14
Now this is were I am confused.
Can I flash the radio Rom without affecting the o/s Rom, I have downloaded a couple of radio rom versions but not sure if you do it the same way as I am scared of over writing something.
Also could anybody advise if they are in UK on O2 which version gives best reception.
Any further advice much appreciated.

[HELP] Bricked TyTN

Hi,
I'm kind of new around here.
My problem is as follows:
- TyTN running PaysRom for about 9 months
- Started to get very sluggish
- Unable to get signal
When i booted my HTC the 'R' and 'G' that appear on screen and used to have values in front of it now display 'none'.
So, I connected it to my PC, 'activesynced' it and tryed to install a new ROM, hoping it would solve the problem.
But the new ROM wasn't installed sucessfully and now all I got is a brick.
I can't even connect it to ActiveSync since it's not recognized.
Is there any solution to my problem?
TIA,
hype

Can you get to the Bootloader?

Yes..
By pressing the Ok+Power+Reset on the bottom button, I see the 'RGB'+white thingie, that I believe is the bootloader..

What SPL do you have? Is it Hard SPL V7(2.10)?
If it is, use the sd card method to install a new ROM.
remember to backup your card 1st.
1. Format 2Gb or less sd card FAT32. Copy .nbh file of the ROM you want onto it and rename to hermimg.nbh .
2. Insert card into Hermes and reset into bootloader.
3. If all things have been done right, follow the prompts....
If the radio ROM has died, I'd suggest trying to flash the Shipped Stock ROM 1st and see if that actually fixes the problem with the blank values on R & G. WM06 upgrade of shipped carrier ROM should also work.
Cheers...

Tks for your response.
I tryed the SD Card method already, with no sucess.
The red stripe shows as follows:
Code:
HERM200
IPL-1.04
HERM200
SPL-2.03
Everytime I tryed on another ROM I always perfomed it using SafeSPL.
Since I don't have 2.1, what can I do?
Tks for all ur help.

What happens when you try and flash a ROM over?
Do you get any kind of error?

You need to find the SHIPPED STOCK ROM. WM06 upgrade should be OK as the CID should match.
Put Hermes into bootloader and connect to PC after unticking "Allow USB Connections" in Activesyncs settings on the PC.
Run the RUU_Wrapper.exe file of the SHIPPED STOCK ROM. ven though activesync won't etect it, the flash file should. Follow the prompts.
Good luck as this seems to be the only way to fix this.
Good Luck...

You might be able to flash a Stock WM5 ROM using the SD Card method. Worked for me when I had SPL 2.03. In fact that's the only ROM it would let me flash over when mine bricked.

[Q]Stuck in "smart mobile"(Edit3.5)HELP REALLY NEEDED.

Hello!
I am new here as you can see. this is not primary proplem anymore.
I installed XDAndroid GBX0C 2.3.7Build to my HTC balckstone and everything works well, but camera tells me "camera error; Cannot connect to camera."
is there any fix for that?`
and the other thing, when i boot phone it goes to win6.1 and i have to go settings etc. and boot it from haret.exe.
so am i done something wrong or something? Solved
So if somebody can help me i would be very pleased
Ps. And sorry my bad english, i just a finnish.
Edit: I try reinstall, i post is changes comes.
E: No changes, still not working.
EDIT!!!!
SO if someone can help me, place do it
E.
And this just happend, phone just stop working whit black screen.was have to took battery off, and then it took about 10-30min to boot to win again.
THIS IS PRIMARY PROPLEM.
AAAAND now it wont even start. stuck in "smart mobility"...
Please read post's for more information.
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.
Could I solve this proplem if i unlock and install custom rom? just wondering if that would help?!

Hi,
"Smart Mobility" screen
I had that problem too, and did a hard-reset.
Hold Volume Up + Volume Down buttons (hold hard) and press Power switch until you see the warning sign to confirm a hard reset.
The system will do a re-flash of the original Windows Mobile ROM.
Start Android by running HaRET from Windows Mobile
Yes, you have to run HaRET.
You can make it simpler by making a short-cut in Windows Mobile Start Menu.
Tap and hold on HaRET until you see the Dialog Box to Cut, Copy, etc.
Tap Copy.
Go to Device-Windows-StartMenu, paste as a shortcut
These steps are in the Touch HD Manual. If you do not have one, download it from the HTC website.

chan.sk said:
Hi,
"Smart Mobility" screen
I had that problem too, and did a hard-reset.
Hold Volume Up + Volume Down buttons (hold hard) and press Power switch until you see the warning sign to confirm a hard reset.
The system will do a re-flash of the original Windows Mobile ROM.
Start Android by running HaRET from Windows Mobile
Yes, you have to run HaRET.
You can make it simpler by making a short-cut in Windows Mobile Start Menu.
Tap and hold on HaRET until you see the Dialog Box to Cut, Copy, etc.
Tap Copy.
Go to Device-Windows-StartMenu, paste as a shortcut
These steps are in the Touch HD Manual. If you do not have one, download it from the HTC website.
Click to expand...
Click to collapse
I have tried hard reset, but that didn't work, and tried to put original rom too, and nothing happened. I have 2 original roms
RUU_BlackStone_HTC_FIN_1.14.414.2_Radio_52.49a.25.26_1.09.25.14_Ship
RUU_BlackStone_HTC_FIN_1.56.414.0_Radio_52.62.25.34_1.13.25.24_Ship
but those didint work. i will try today againe. and then if it going to work i will put that haret to start menu.
I'll try that 1.14 first...
flashed that 1.4 rom and waited about an hour and nothing happend... i jsut did hard reset and wait againe if it gonna boot now...
i was thinking that should i put custom rom, coz if something went wrong whit the official?
I mean if there is something wrong in phones hard drive? like something wrong whit registery or something?
something that wont let win start. if there is, how i can fix that?

masentava said:
Hello!
I am new here as you can see. this is not primary proplem anymore.
I installed XDAndroid GBX0C 2.3.7Build to my HTC balckstone and everything works well, but camera tells me "camera error; Cannot connect to camera."
is there any fix for that?`
and the other thing, when i boot phone it goes to win6.1 and i have to go settings etc. and boot it from haret.exe.
so am i done something wrong or something? Solved
Click to expand...
Click to collapse
GBX0C2.3.7 Build is on SD card.
You will need to boot from Windows Mobile first, then run HaRET to reboot to XDAndroid.
If XDAndroid hangs, you need to remove battery, put back battery and power on. Then you see Windows Mobile and do above step again.
Always, from XDAndroid to go back to Windows, you need to Power Off, and then Power On again.

chan.sk said:
GBX0C2.3.7 Build is on SD card.
You will need to boot from Windows Mobile first, then run HaRET to reboot to XDAndroid.
If XDAndroid hangs, you need to remove battery, put back battery and power on. Then you see Windows Mobile and do above step again.
Always, from XDAndroid to go back to Windows, you need to Power Off, and then Power On again.
Click to expand...
Click to collapse
I undestood that... but thats not the proplem anymore coz windows wont start, its stuck in "smart mobility"
i tryed to flash original rom's bot that didint work....
so prolem is how do i get windows back to work?
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.

masentava said:
I undestood that... but thats not the proplem anymore coz windows wont start, its stuck in "smart mobility"
i tryed to flash original rom's bot that didint work....
so prolem is how do i get windows back to work?
now i have tried flashing original rom from CPU and Storege card... both install it correctly and says everyting is ok, but still its stuck at "smart mobility" screen.
it wont even shot in the right corner that red text of versions etc.
so what's the solution to this proplem? i would be very pleased if some one could tell me how to fix my proplem. i know there is someone who know what i should do.
Click to expand...
Click to collapse
You say you are flashing the original ROM. You mean the original HTC Windows Mobile 6.1 ROM? I understand you can only get this done only from HTC authorized centers.

(800) stedntf
chan.sk said:
You say you are flashing the original ROM. You mean the original HTC Windows Mobile 6.1 ROM? I understand you can only get this done only from HTC authorized centers.
Click to expand...
Click to collapse
I have
This
RUU_BlackStone_HTC_FIN_1.14.414.2_Radio_52.49a.25.26_1.09.25.14_Ship
And this.
RUU_BlackStone_HTC_FIN_1.56.414.0_Radio_52.62.25.34_1.13.25.24_Ship

Blackstone/HD Links | Guides | Stickies | Roms | Read before posting
http://forum.xda-developers.com/showthread.php?t=999925
U have to install HTC USB Sync Drivers drivers
Put the phone into bootloader by pressing volume down + power button
plug the usb cable to the computer/laptop
and then run the shipped rom executable file... when the tricolor screen displays USB at the bottom.
else extract the RUU_signed.nbh or any file with .nbh extension from the shipped file with zip viewers like 7-zip
rename the file to BLACIMG.nbh
Put into the root of memory card
put the phone into bootloader and follow the screen instructions..
And the most important thing... search the forum.. before posting..
Hope this works for you

Hi there! I think that you can't reflash even a Original ROM without unlock the phone with new Hard-SPL from Olinex ,considering that you have tried a Hard Reset and nothing happened ,your last option is to unlock the phone and reflash the ship ROM ,or to flash a custom ROM ( is not a good solution if you still have warranty,but still you cand revert your stock SPL:good so ,you have nothing else to lose , all is left for you is to try what i said before . If you don't know how to do it,let me know and i will post the exact links to instructions.

Hi all,
You can try a NAND ROM like the new release of Fagyi. There is an easy step by step manual to installation. You will lose winmo, but you will have a real android.
It looks pretty and he has solved many of the issues of previous versions.
Regards

CristianCRS said:
Hi there! I think that you can't reflash even a Original ROM without unlock the phone with new Hard-SPL from Olinex ,considering that you have tried a Hard Reset and nothing happened ,your last option is to unlock the phone and reflash the ship ROM ,or to flash a custom ROM ( is not a good solution if you still have warranty,but still you cand revert your stock SPL:good so ,you have nothing else to lose , all is left for you is to try what i said before . If you don't know how to do it,let me know and i will post the exact links to instructions.
Click to expand...
Click to collapse
well, maybe i will try to unlock, i looked some instruction, aaand didint understood
So if there is quide to dummiest dummies, so i think that would help me!
But thx to all answers!

Do a Search and read the posts
masentava said:
well, maybe i will try to unlock, i looked some instruction, aaand didint understood
So if there is quide to dummiest dummies, so i think that would help me!
But thx to all answers!
Click to expand...
Click to collapse
You need to understand what you are going to do or you may end up with a phone that does not work anymore.
Do a search of the forum and read the posts. There are so many.
http://forum.xda-developers.com/sitesearch.php?q=unlock blackstone