How to backup WM5 in S200 - JAMin, XDA Neo, S200 General

Hello, sorry for my english
I ask a very simple question from Barcelona (Spain)
Someone know a program to perform a full backup of the wm5?
I'd like to install wm6, but i'd like to have a backup.
Thanks in advance for you answers
M.A.

Hi,
The backup question will depend on which model is yours G3 or G4 (do a search).
If your model is a G3 in the prophet section of the wiki there is/was a way to dump the rom using teraterm in a SD card.
If your model is G4, I suggest that you read http://forum.xda-developers.com/showthread.php?t=392325 as I wrote there I did the backup but I never restored the rom, but our moderator says it works.
Cross the fingers

Hi Myer, thanks for you answer.
I look you link, and after to jump two more I get http://forum.xda-developers.com/showpost.php?p=2327531&postcount=58, where "imee.h" says this steps to proced:
How did I do the dumping?
1) I put JumpSPL (the three files: exe, lnk and SPL image) to the device root.
2) Unplugged device from PC.
3) Deactivated ActiveSync USB connection.
4) Ran the lnk to JumpSPL on device.
5) Connected device to PC.
6) Ran the mtty on PC.
7) Hit enter -> got Cmd>
8) Entered the command "r2sd all"
After this hollydays I'll try to do, because i'm not very happy to run in my device JumpSPL, without any more info, also i can get conection with mtty via USB, it can not open USB port.
Then after Hollyday i'll try.
Thanks for you help
M.A.

I'll forget,
My device is G4
Un saludo
M.A.

Your best way is to get a software backup program. I use Sprite Backup, it will back up contact, registery, EVERYTHING.
One thing you should know, if you dont already, is that you should not use restore a backup from previous ROMS. If you only backup contacts & Calender then that is fine, but NOT registry or system files, you will end up bricking your fone.
Software backup if much easier download a trial of the lite version and if u like it (i do) purchase full, approx 19$.

Related

problem magician

I am new of the forum, I have just purchased a nm8 used magiacian (t-mobile MDA) it is I bring a problem.
The preceding owner has begun an updating of the rom that has not gone to good end and the device doesn't now set out anymore and from the following error:
USB V1.00 (if connected USB).
Serial V1.00 (if disconnected).
Bootloader mode ?
What must I do for going on?
I hope in a help
Best regards Luca
help
I pray you helped me, the first post is from beginners, but believe I have followed the standard procedure.
unloaded the rom
unloaded no-id
always tried upgrade more times failure.
HELP !
for the beginning you should use a standard ROM to get familiar with the device.
just go to the t-mobile website, downloads, chose your device type and then look for files named softwareupdates or so.
they will be in zip-format.
there will be an application in there. just go into bootloadermode, connect your device and start the upgrade. it's completely guided and will last about 20min.
although most of the ppl that read/write in this forum didn't install the eROM, I think you can start with all the cusomization stuff. If you have become more familiar with your mdac, you can try other modified ROM's.
just ask if you have more questions
greetz Stefan
i have to say that using standard rom (jam rom downloaded from club imate)
the upgrading applications hangs.....
and leave magician in booting mode, ready to be erased....
i was desperaded, but last experiences with motorola phones and its firmwares advice me to try again
so i had to launch againg that apps and it starts erasing actual rom....
i think there is a bug in few roms.... may be only in its installer
Have tried with the T-mobile rom but doesn't even go with that!
Caslu,
Have you tried a hard-reset?
If so: I guess you've got a decent TMO magician rom downloaded. So get maupgradeut_noid.exe from the ftp. Extract all the files from your TMO shipped-rom & put them in a directory, so you get some .nbf files, enterbl.exe & maupgradeut.exe. Now put the maupgradeut_noid.exe in the same directory. Connect your magician to the usb. It should read usb v1.00, if your magician isn't in bootloader press camera&power&soft-reset at the same time for a few secs. till you get the usb or serial reading.
After connecting it to the usb execute the maupgradeut_noid.exe twice, first execute might give an error 120 second should finish.
If this fails make sure you got a magician & not a charmer.
If it's a magician return it, cause I think it's broken. Hey why buy a device that's in an inconclusive state??
Regards, M
I think really that It broken.
Have picked it because little cost!
non one reply .......
caslu said:
I think really that It broken.
Have picked it because little cost!
non one reply .......
Click to expand...
Click to collapse
Download the latest shipped ROM for the country your magician was first sold in.
Ensure Activesync is in the normal mode (USB check is ON).
Run the executable ROM update program.

QTEK ROM

I would like to flash my mda vario with the qtek rom, to solve the issue with the device resetting itself due to having a sd card installed, and to generally speed things up etc. I have visited the wizard ftp site on here, and navigated to the qtek folder, but there are about a million files listed. I am currently a UK user running an mda vario with t-mobile. Which file should I use? Once I have the correct file how do I then install it to my device? After the update will I be able to restore my previous files and settings with my SPB backup file?
Thanks!
bump
as a newbie myself maybe i can lend you a hand.
first of all...in order for you to flash your mda to other rom, you need to sim and cid unlock ur phone. then you download the latest ROM with WWE to your desktop.
connect your wizard to your pc via activesync 4.1, make sure your device is fully charge at all time. after you have sim/cid unlock ur phone, soft reset your device. then run the ROM exe file and follow on screen instruction.
before you start unlock and flasing ur phone, please use the search function and try to look for step by step instruction. thats wht i have done for a few days and manage to flash my mda vario with the latest qtek rom and a custom radio rom. cant say how happy i am with the phone now.
This is the latest qtek wwe rom ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
with spb backup no you will not be able to do a full restore because it will overwrite the registry etc..
Do a custom backup and tick all boxes except system data

How to save my Artemis by sd card

Dear everybody,
I have also killed my 2 day old MDA compact 3 by using the PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap.exe (Feel really frustrated about it)
It will not load windows only
IPL 1.13.0001
SPL 1.13.0001
GSM 02.49.90
OS 1.28.0.0
I've tried a lot but nothing has worked so far. Now my last resort is using XDA tools to make a bootable sd card.
Is there anyone who make a file that the artemis can use of an SD card?
I would be very much obliged!
did you do CID unlock before installing new ROM?
CID unlock is not required for flashing the PDAMobiz Powermap 1.1.2 ROM. Just make sure you follow the right instructions. I did it and you can find it here:
http://forum.xda-developers.com/showthread.php?t=294830&page=2
But make sure that you have synced your Outlook data on desktop as there is something wrong with restoring from backup file the PIM related info (I use Spb Backup, but seems it is same with any backup application)
http://forum.xda-developers.com/showthread.php?t=295295
more info.
ianvanhaaren:
1. Please provide more info what exactly happens when you try to turn on your device.
2. What type of error you have when you try to re-flash device? At what percent it stops.
3. Connect device to USB, disable USB connection in activesync. Start mtty console, choose USB type connection (mtty attached, in case you need it).
4. type set 32 in console. send this output.
If CID area on device is corrupted, for the moment only imei-check who knows how to re-calculate this area. Even so, if device won't boot in windows it will not help. You need to connect to device thru jtag interface, in order to load modified spl into ram and perform writing into security area, to recover it. Imei-check says, they know jtag for Artemis.
It may cost you a bit of money.
If you have an option to send it to service center, do it. It would be your best choice.
Regards.

WM6 upgrade fails,need help,will donate if problem is solved (please help)

After I read http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
It says The WM6 does not work on PH20A2 (Harrier) (Audiovox PPC-6600 / PPC-6601 / XV6600)/ CDMA device! <-- that is my mistake
My mistake steps:
1. upgrade 2003 2nd edition to WM6 (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
2. use mytt <-- may not hurt (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
3. Do hard reset, format the PPC (stuck in white screen, then do soft reset. The PPC will ""NOT"" stop if I remove the battery for a few seconds and put battery back)
reflash
Have you tried re-flashing with the original ROM?
AbuGWM5 said:
Have you tried re-flashing with the original ROM?
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
You got to revert back to WM 2003 SE with your original OS.
April 1 said:
You got to revert back to WM 2003 SE with your original OS.
Click to expand...
Click to collapse
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
king2004c said:
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
Click to expand...
Click to collapse
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
rickwyatt said:
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
Click to expand...
Click to collapse
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
try to take out first SD Card and SIM CARD from your BA first before connect to your notebook/PC
king2004c said:
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
Click to expand...
Click to collapse
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
xplode said:
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
Click to expand...
Click to collapse
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
king2004c said:
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
Click to expand...
Click to collapse
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
April 1 said:
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
Click to expand...
Click to collapse
I have already find a CDMA rom. Now the only problem in my phone is bluetooth
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
xplode said:
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
Click to expand...
Click to collapse
So far, I can use the phone without any problem. Previously, I tried to upgrade my phone because I want to use bluetooth headset to listen music. That can only be done in WM5 or later. Now I reinstall my CDMA version of WM2003. I find out that the bluetooth does not work due to expire of lincese key. Does anyone have any suggestion how I can over come it? I just want my phone back to exact a few day ago. Thanks
thanks
lincese
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
meehaa said:
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
Click to expand...
Click to collapse
Thanks, but does not work on my PPC6600

[ROM] Windows Mobile 6.1 for HTC ELF/ELFin

VERY IMPORTANT TO NOTE:
This custom ROM is built for installation onto both the ELFs and ELFins.
DO NOT FLASH IT TO ANY OTHER DEVICES! I will not be responsible for any damage to your device.
FOR FIRST TIME CUSTOM ROM UPGRADERS:
1. Copy the Cert_SPCS.CAB and EnableRapi.CAB from the zip folder to your device's Storage Card.
2. Install the two cabs to your Device memory and do a soft reset.
3. Restart your PC or laptop (Optional)
USING THE INTEGRATED ROM UPDATE UTILITY WITH USPL CID UNLOCKER:
(ATTENTION: REMOVE YOUR 4GB, 6GB or 8GB mircoSDHC CARD WHEN FLASHING THIS ROM!)
1. Turn off your computer's Anti-Virus software if you can.
2. Activesync your device to your PC using USB port.
3. When the connection is completed (after synchronisation), double-click on [START] batch file to begin the integrated ROM Updating Utility.
4. Now follow closely the instructions that appear on the computer screen.
5. Press [ENTER] to accept at each prompt to continue the process.
6. After Step 2/3 of USPL CID Unlocker, the device screen will turns "blank white" and your activesync icon gray (in Windows XP only).
Congratulations! You have successfully CID unlocked your device. Press [ENTER] to proceed NOW!
(NB: If you failed to see the "blank white" screen, then your CID unlocking has failed.
Restart your installation process from Step No.1)
7. Your device will now proceed to update your rom. Select and hit [NEXT] at each prompt to continue.
8. When the rom updating is completed at 100%, your device will restart automatically.
9. Congratz! You have successfully upgraded to a new rom.
Enjoy!
__________________________________________________________________________________________________
I did this had no problems with my htc elf/elfin/touch over the moon with it!!!
REMEMBER: all of your installed applications will be swiped of with this ROM.
Also have fun with your upgraded windows mobile 6.1 HTC ELF!!!
__________________________________________________________________________________________________
Whiplash1995.
Cheers
WM6.1
for
ELF
__________________________________________________________________________________________________
please tell me if there is any problems post a reply...
forgot to menchion download the full thing at > http://thepiratebay.org/torrent/4277382/Windows_Mobile_6.1__en_for_HTC_Touch
DO NOT BE A NOOB FOLOW THE ON SCREEN INSTRUCTIONS!!!!!!!!!!
__________________________________________________________________________________________________
'Start' batch file does nothing.
Tried opening it directly from a command prompt, but still nothing, except it opens another dos box.
Thoughts ?
The 'start' batch file fails because the first command is 'cd RUU'. but there is not a folder called RUU.
Then it tries to rename two files which also do not exist. Hence it never actually arrives at the exe file to unlock & install the ROM.
Can this work if you simply run the exe file without renaming & changing folders ?
Hi, and thanks for that script...
The .bat works well for me but while updating the rom, I've got an 270 error... 'The images files is corrupted please check your update utility'
does any one had the same issue on his phone? Do you think I just need to download it again? (concidering that the zip file uncompressed normaly, I assume it works well...)
Thanks for your answers...
upgrading MDA Touch
please i need your Help.
I have download the" touch essential V3.5 Manilla" on my PC. But i don´t know how to send it to my MDA.
Activsyc is working.
Where kann i fine the cert_CAB?
I have also unpacked the V3.5 manilla, but there is no way to run it in the MDA how should i do this.
many thanks
My 2 cents...
If I were you I wouldn't rely on a torrent posted by a junior member (age 12) and rather download the ROM posted by Football on Rapidshare => See his post HERE <=.
I've been using it from day 1 without any problem...
gruikdadude...
gruikdadude... I understand were you are coming from but I have been very carefull on what i look for and actually this torrent file was uploaded by someone on xda developers so i am saying the update worked fine for me so why shouldnt it for you so before you start criticising a me for posting something that is just to assure htc touch owners that there is a reliable WM6.1 upgrade is there anything wrong with this......... NO!!! so before you criticise think twice !!!bell end!!!
__________________________________________________ ________________________________________________
Whiplash1995.
Cheers
WM6.1
for
ELF
________________________________________________ __________________________________________________
r there any direct download links?
as i prefer not to download through torrents...torrents downloading over here sux...
whiplash1995 said:
so before you criticise think twice !!!bell end!!!
Click to expand...
Click to collapse
Not criticizing you at all: just warning xda members that downloading any posted ROM can be harmful for their PPC...
EOF
Can you plz. give us link for zip file instead of the ttornet one
thanks in advance
can you tell me the diffrences between this rom and the original 6,1 rom? i see no manilla2d, but more differences?
hi i tried the whole procedure , but i get the ERROR[270]: Image file is currupted, can anyone help regarding this error, how to get the uncurrupted version?
Since this rom is giving a lot of people problems, why not just use one of the verified good roms from the Elf Upgrading subforum?

Categories

Resources