I am new of the forum, I have just purchased a nm8 used magiacian (t-mobile MDA) it is I bring a problem.
The preceding owner has begun an updating of the rom that has not gone to good end and the device doesn't now set out anymore and from the following error:
USB V1.00 (if connected USB).
Serial V1.00 (if disconnected).
Bootloader mode ?
What must I do for going on?
I hope in a help
Best regards Luca
help
I pray you helped me, the first post is from beginners, but believe I have followed the standard procedure.
unloaded the rom
unloaded no-id
always tried upgrade more times failure.
HELP !
for the beginning you should use a standard ROM to get familiar with the device.
just go to the t-mobile website, downloads, chose your device type and then look for files named softwareupdates or so.
they will be in zip-format.
there will be an application in there. just go into bootloadermode, connect your device and start the upgrade. it's completely guided and will last about 20min.
although most of the ppl that read/write in this forum didn't install the eROM, I think you can start with all the cusomization stuff. If you have become more familiar with your mdac, you can try other modified ROM's.
just ask if you have more questions
greetz Stefan
i have to say that using standard rom (jam rom downloaded from club imate)
the upgrading applications hangs.....
and leave magician in booting mode, ready to be erased....
i was desperaded, but last experiences with motorola phones and its firmwares advice me to try again
so i had to launch againg that apps and it starts erasing actual rom....
i think there is a bug in few roms.... may be only in its installer
Have tried with the T-mobile rom but doesn't even go with that!
Caslu,
Have you tried a hard-reset?
If so: I guess you've got a decent TMO magician rom downloaded. So get maupgradeut_noid.exe from the ftp. Extract all the files from your TMO shipped-rom & put them in a directory, so you get some .nbf files, enterbl.exe & maupgradeut.exe. Now put the maupgradeut_noid.exe in the same directory. Connect your magician to the usb. It should read usb v1.00, if your magician isn't in bootloader press camera&power&soft-reset at the same time for a few secs. till you get the usb or serial reading.
After connecting it to the usb execute the maupgradeut_noid.exe twice, first execute might give an error 120 second should finish.
If this fails make sure you got a magician & not a charmer.
If it's a magician return it, cause I think it's broken. Hey why buy a device that's in an inconclusive state??
Regards, M
I think really that It broken.
Have picked it because little cost!
non one reply .......
caslu said:
I think really that It broken.
Have picked it because little cost!
non one reply .......
Click to expand...
Click to collapse
Download the latest shipped ROM for the country your magician was first sold in.
Ensure Activesync is in the normal mode (USB check is ON).
Run the executable ROM update program.
Related
Hello,
because my posting in this forum wasn'n answered i tried to fix together with Mr. Wolf from Wolfsoft (www.wolfsoft.de - also great for fast XDA RAM-Upgrades) with the informations i found.
Everytime i write the i did something - i mean - we did it! We worked hard together for this solution.
-----------------
First:
Maybe, surely you can destroy you XDA-ROM more than it was destroyed before. I not guarrante or take responibility for any errors or damages occuring while trying the next steps.
Situation:
I upgraded my german O2-XDA in the wrong way. After this I had the following problem:
- The O2-bubbles appearing after soft- or hard resetting the XDA are displayed for 3 or 4 minutes. In the right bottom corner of the display the Version of WinCE ist dissplayed (3.14), after some times someting more was shown but that seemes to be from a crashed source.
- After the "pling" a white screen with a blue bar on the top is displayed. The screen-light doensn't turn off. Nothing more happened, after 20 or 30 Minutes the XDA performs a soft reset automatically - after this the same problems occuring
Requrements I needed to fix my problem:
- 1 (better 2 SD-Cards with minimum 32MB Capacity)
- XDA Cradle connected to the PC and Power
- in some cases 1 Charging cable (USB or Power) with a connector for the XDA
- The Program A and Program B - Files provided by german O2 website
- The repair.zip-File provided by XDA-Developers
- A second XDA or a SD-Card-Reader connected with your PC
- many time
- Your XDA must have a working bootloader (mine was Version 5.15), try it by holding the Power-button while performing a soft-reset.
What I did:
- After entering the Wallaby-Bootloader an "gsm-error" - message appears after 1 minute of "wait"
- I entered the SD-Card-Menu by pressing the Contacts-Button on the left-top of the XDA
- I choosed Write CE to SD in order to save my original CE in order to avoid unuseful Questions in case of repair-fail by O2-Support
- After this I performed a soft reset an waited for 1 or 2 Minutes after the white screen appeared
- While tis time write the contents of the unzipped repair.zip to the SD-Card using the SD-Card-Reader or the second XDA
- Now i pressed the "Volume" - Button on the left side for many times, after some trys (if it is not working perform a soft reset and try new) I saw a non-working Today-Screen
- Now insert the SD-Card on you have written the files from repair.zip
- There are 2 possibel reactions:
First: You get a message to format your SD - DO NOT!!!! In this case remove your SD-Card, connect your XDA with the Charging Cable and perform a soft reset. It is okay that there is no charging light. After you entered the Today-Screen insert the SD - do not remove the Charging-Cable! Then it will work.
Second: Installing beginns without any problems
Now your Radio Stack-Module will beginn to be updated. In my case I got the 1% Error discussed in the forum.
- Remove the Power cable, connect your cradle with the PC and the Power, perform a soft reset and wait what is happening. After the error occurs don't push the ok-button. Simply press the start-tab (or anywhere other excluding the message). Now take the XDA out of the cradle and after this put it in again, still with the error message on the screen. Now an active sync connection will be shown on both, your XDA and the PC! If you have this case, it looks good.
- If this doesn't work, replace the RSUpgrade.sa.cab-File from the repair.zip with the same named File, whats included in the program_B.exe (extract first, you will find the result in <Harddisk-Device:\Programme\Programm B) and writhe both on your SD
- Soft reset the XDA, ignore all errors, do not put the new written SD-Card in - open the Active sync-connection and delete the both newest files in the Windows-Directory of your XDA. If you can't delete, rename the file. After this perform a new soft reset.
- You will get a "file not found error". Try to temove and insert your XDA in the cradle to get an active sync-cennection. If this doesn't work insert the new written SD
- Try new flashing again again, maybe it works. If not try to push on the screen and remove and reinsert your XDA in the cradle to get a Connection.
- If there is no possibility to get a connection - i do not know any futher solutions - sorry.
If you get the connection, perform the normal Flashing with Program A provided by your Provider. After this is successfully completed you will see the loading-LED again! Congratulations!
If this is completed charge your Battery to at least 70% - be patient, it will take up to 1 Hour!
After this perform Programm B provided by your Provider. If this successfully completes - Congratulations - you are up and running!
I don't know, if I had happy circumstances, but this worked to gat my working XDA back!
If it do not work, use the first SD-Card containing your old CE to copy back your old ROM in order to not loose your support by your Provider. Simply insert the card into your XDA and perform a soft-reset while holding the Power-Button. Everything looks broken but original!
Please feedback in the XDA-Forum-Thread, if it worked at your XDA or if you have any hints for improvements this steps. Thank you!
Best regards from Berlin/Germany to all XDA-Fans like I am!
Miwu
Very detail.....thanks a lot ! :lol:
Tried your solution but i don't know which files i should delete cause when i delete the latest two files i get no error message...
When trying to install Programm a anywway i get a Connect Power Message and the installation stops.
Edit:
I managed to get the file not found error by renaming the RsUpgrade executable but still get the Power Adapter not plugged in Error...
So it would be very important to know which Programm A you used.
Hello,
@ianrush
Have you been able to get an active sync connection as I described?
You have to delete the file causing the Radio-Stack-Update after restart, I think they are located in the Windows directory of your XDA. If you let your XDA order the files by date the 2 newest files are the ones for updating the Radio Stack and causing the 1%-error. In deleting these files you can get your XDA booting without starting the gsm and getting the Active-Sync-connection. To break up the Installation you must delete these files (i remenber that on (the one that must be renamed) was only 35k or in this area, the other one was much larger).
After deleting and restarting by soft reset you don´t get the 1%-error-message, but another one like "The file can´t be found). But if you see this message (do not press okay!!!!!) you can use your Active-Sync-Connection to flash with Programm A and after this programm B.
The files (germen version) are located here.
Klick at the link "Download Software-Update" and accept the conditions by clicking "Akzeptieren". After this a new window is displayed for downloading the Software. The versions are:
CE: Version 3.19.01 -
Radio Stack Version 4.21
"Teil 1" means Programm A
"Teil 2" means Programm B.
Remember, it is the german version with some german specials like the "Homezone". But you can turn it off and while I see, that you are from Austria, I think you won´t have any problem with the language...
Isn´t it very strange, that 2 german speaking people trying find solutions in english??? :?
Best regards from Berlin!
Michael
I have no problem starting an Active Sync Connection, my problem is, that i get this odd Error Message which tells me to plug in the Power Adapter, which is obviously connected...
There is a much easier way of getting rid of the Flash Prog bei simply deleting the RsUpgrade link in the Auto Start Folder in the wwindows directory and its also possible to start an Connection via AS.
My real problem is the battery charge check before the real flashing of the RSU.
I tried it with the mentioned O2 files and also with Tmobile.at/de files.
A solution may be to "crack" the installation file or to write a small prog wich tells PPC that the battery is chraged.
Many thanks for your help, but it didnt solve the problem for me.
PS: Well its an English Forum so i think we should stay in that language
Oh, I forgot to write that one.
The charging light, wich may be an indicator for the XDA-OS for the supplied Power came back as we installed the O2 Radio Stack via the Active Sync-Connection bevor performing Programm A - Upgrade. Try to perform Program B - Update first, in our case we got our lovely orange light back and then performed the Programm A and Programm B - Update again!
Regards again!
Michael
Didn't work for me either.
The BIG question is how the hell did you get your XDA charging his battery again ? I believe that this will help many people to get their 1% Flash failed problem solved.
Hi !
I will try this method tomorrow.
Sebi
Hello,
I do not know why, but after (failed) installing Programm B after connecting via Active Sync first it worked . Maybe because of the working version-combination of Radio Stack and CE.
Regards
Miwu
@Sebi Please post if it is working!
Hi !
Don't work for me.
My problem is same this:
Posted: Fri Aug 29, 2003 19:26 Post subject:
--------------------------------------------------------------------------------
I have no problem starting an Active Sync Connection, my problem is, that i get this odd Error Message which tells me to plug in the Power Adapter, which is obviously connected...
Click to expand...
Click to collapse
Best regards
Sebi
miwu
I followed your steps and got the following message on my device:
The file "\Windows\RSUpgrade.exe" is in use or is in ROM. If the file is not in ROM, please close the application using the file.
Please advise
Anaq8i,
if this messege appears then rename the file "\Windows\RSUpgrade.exe" with an new name like "\Windows\RSUpgrade_used.exe" restart the device and follow the further instructions.
Hope that helps
Regards
Michael
miwu,
I cannot rename it, nor can I delete it, I think because it is in ROM. Please keep in mide that the I have not closed the error message after the 1% halt.
I reached the point were I can access my device and can sync with my PC. If I try the Programme A install, I get the message " WARNING 001: POWER ADAPTER NOT PLUGGED IN, Please plug the power adapter into your Pocket PC". Every time I try the RSU upgrade I get the 1 % error. Any suggestions will be appreciated
Hi anaq8i,
please try to rename the file by using the Active-Sync-Connection an the Explorer of your big Desktop-PC. The file cannot be in the rom, it is located in the ram of your device in order to get deleted after upgrading. Try to rename the file this way, then perform a soft-reset (not a hard one) then you will get an error-message that sonds like "the file ... cannot be fount", then put your device in the crade for active sync and try to install the original Programm B of your Provider (not the file from repair.zip). That worked at my XDA.
Please answer how it worked.
Regards this time from Hamburg/Germany
Michael
thanx a lot, have the same error, now all worx fine!
czeky thanks for answer. I am glad that my description was helpful Doe it work for other users?
@ czeky
would you also please be so kind and tell us if u tried any other steps than mentioned by miwu ?
If i treally worked with your XDA there you must have done something different then anaq8i, Sebi and i did...
miwu
I reached the point that I can boot my XDA and can sync with my PC. But I still cannot install /upgrade the RSU software, I still get the 1% error. If I try to install Porgramme A, I get the "POWER ADAPTER NOT PLUGGED IN" error message. I never reached the orange light stage on the XDA.
Anything else I should do?
@anaq81
Did you try to rename the described file via Active Sync? I posted it some day ago ...
Hi
I am new here and i have problem
When i turn on my qtek9000, i recieve message Serial V.100.
If i connect USB cable it displays USB instead of Serial.
This happened when i tried to do radio upgrade (through usb hub, sim and sd were also in phone...).
I have 1gb SD card and also card reader mounted in laptop, so transfering files should not be problem.
Can someone help me with step-by-step procedure how to make my qtek work back. I used a lot of search but i am even more confused....
I just remember that when qtek worked Radio was something like 1.0.3.1 and also WWE was writen somewhere....
Probably i should put rom to sd with ntrw (which wersion of both),.......
please help....
might be a dumb question on my part - but have you tried a reset (initially a soft one but then a hard one of course, if nothing else works...) ???
I mean you will at least be able to revert back to the condition 'out of the package'...
Hope everything works out!
jup.both things NOT HELPED
looks like you're stuck in the bootloader mode....
try flashing the rom & the radio rom once again by connecting it to your laptop's usb...
i guess something screwed up while you were upgraging your radio rom...and you'd need to redo it!
Best,
San
can you please write me a procedure?
You might want to check the following thread. Everything is well described.
Cheers
hrb
http://forum.xda-developers.com/viewtopic.php?t=32725
i am trying to download files but i get permission denied all the time
You mean you get an error when clicking this link ?
ftp://xdaupload:[email protected]/Universal
I don't understand that, it works perfectly well for me
Cheers
hrb
I have solved problem with Radio upgrade. I am in much better mood now. 8)
Anyway i have 4 more questions.
1.) I am using bluetooth car-instalation Parrot CK3100. I am wondering if is possible to transfer any other sound except telephone conversations to that device. When i had Nokia 9500 i was able to hear every single click,tone,...i made on phone also on car-instalation. I also heard nokia ringtone in car instalation.With qtek i am getting generic car-instalation ringing tone instead of phone ringing. Otherwise primary intention (hands free talking) works fine. I would like to have that to be able to hear voices from various GPS software.
2.) Since QTEK9000 is PDA and phone in single unit I would like to have in car GPS application "always on top". Like previously mentioned i can easily manage my calls with car-instalation. Therefore i would like to run Phone section in background or GPS applications on top.I hope you will understand what i would like to say
3.) I also need in-car holder for qtek. Do you have any reccomendations?
4.)
My settings:
R: 1.04.02
G: 42.37.P8
D: 1.13.64.WWE
Is that ok or should i upgrade?
Stuck in bootloader mode
Hi guys,
Got stuck in bootloader mode following an upgrade attempt. Tried to reflash radio using the files from the pload folder only to get an error saying it's for the wrong device - tried this several times with the same result.
any ideas?
Is there a binary and a tool I can just do a straight upload?
thanks
Re: Stuck in bootloader mode
Bauser_uk said:
Hi guys,
Got stuck in bootloader mode following an upgrade attempt. Tried to reflash radio using the files from the pload folder only to get an error saying it's for the wrong device - tried this several times with the same result.
any ideas?
Is there a binary and a tool I can just do a straight upload?
thanks
Click to expand...
Click to collapse
try it with this file -
1. put radio.nbf and the file attached below in the same folder and run the exe with ur device connected to usb in bootloader mode...
2. hope it flashes it
S
Thanks DreamTheater
Thanks for your help - unfortunately I got the same message, ie this rom is not meant for this device etc...
Will see O2 can do anything (who's that laughing...???) - was going to buy a new xda mini anyway...!
1. REMOVE your SD/MMC card.
2. Soft/hard reset.
3. Run the upgarde again.
Step 1 above solved my problem.
i've downloaded a t-mobile rom with A2DP for the MDAPro and i want to put it on my XDA exec so i can at last have A2DP on my EXEC. Is there any way to do this, or is there a O2 rom on the way that will give me what i want if i wait a bit longer. If i try installing the rom atm it just says country id error.
Re: How would i install a t-mobile MDA Pro rom on my XDA EXE
[email protected] said:
i've downloaded a t-mobile rom with A2DP for the MDAPro and i want to put it on my XDA exec so i can at last have A2DP on my EXEC. Is there any way to do this, or is there a O2 rom on the way that will give me what i want if i wait a bit longer. If i try installing the rom atm it just says country id error.
Click to expand...
Click to collapse
You need maupgrade utility.
follow this link:
http://forum.xda-developers.com/viewtopic.php?p=246177
I installed it on my jasjar.
A2DP works like charm.
maupgrade utility?
i can't find this anywhere, what is 'maupgrade utility' sorry if i'm missing something obvious.
i have attached a screenshot of the error message i get is there any way around this- i am using a XDA exec and can't find a program to allow me to make the t-mobile rom work
Right,Download the T mobile Exe to a directory of your chosing. using Winzip ( I use winrar) Right click the ExE file, and click extract here.
This will give you about 10 files. one of them will be ROMupgrade.exe. This is the bugger that gives you a problem. Now get a copy of MaUpgradeUt_noiD.exe and put this in the same directory. Unplug your usb cable, do a Boot loader reset. Light, on/off, and reset all together.
Screen goes blank with the word serial top centre NO backlight so hard to see. Plug in USB cable. Serial changes to Usb. now doubleclick MaUpgradeUt_noiD.exe to run it. follow onscreen prompts. takes about 20 minutes. Soft reset at the end. Dont worry if the displayed divice is not a Xda exec. Worked for me just done an up grade to latest full imate release as I'm writing this!! Previously I had the code 120 Country failure before carrying out the above installer exe swap.
HTH
Rob
Would i be able to revert back to xda exec rom simply?
ROBBED666 said:
Right,Download the T mobile Exe to a directory of your chosing. using Winzip ( I use winrar) Right click the ExE file, and click extract here.
This will give you about 10 files. one of them will be ROMupgrade.exe. This is the bugger that gives you a problem. Now get a copy of MaUpgradeUt_noiD.exe and put this in the same directory. Unplug your usb cable, do a Boot loader reset. Light, on/off, and reset all together.
Screen goes blank with the word serial top centre NO backlight so hard to see. Plug in USB cable. Serial changes to Usb. now doubleclick MaUpgradeUt_noiD.exe to run it. follow onscreen prompts. takes about 20 minutes. Soft reset at the end. Dont worry if the displayed divice is not a Xda exec. Worked for me just done an up grade to latest full imate release as I'm writing this!! Previously I had the code 120 Country failure before carrying out the above installer exe swap.
HTH
Rob
Click to expand...
Click to collapse
Hi, i own an xda exec.. and i m pretty much interested in installing a t-mobile rom on it.. but i would like to know that if o2 comes up with a new rom upgrade, would i be able to install it directly on my xda exec without doing any manipulations on my xda.. please reply soon.. thankyou.
Would i be able to revert back to xda exec rom simply?
ROBBED666 said:
Right,Download the T mobile Exe to a directory of your chosing. using Winzip ( I use winrar) Right click the ExE file, and click extract here.
This will give you about 10 files. one of them will be ROMupgrade.exe. This is the bugger that gives you a problem. Now get a copy of MaUpgradeUt_noiD.exe and put this in the same directory. Unplug your usb cable, do a Boot loader reset. Light, on/off, and reset all together.
Screen goes blank with the word serial top centre NO backlight so hard to see. Plug in USB cable. Serial changes to Usb. now doubleclick MaUpgradeUt_noiD.exe to run it. follow onscreen prompts. takes about 20 minutes. Soft reset at the end. Dont worry if the displayed divice is not a Xda exec. Worked for me just done an up grade to latest full imate release as I'm writing this!! Previously I had the code 120 Country failure before carrying out the above installer exe swap.
HTH
Rob
Click to expand...
Click to collapse
Hi, i own an xda exec.. and i m pretty much interested in installing a t-mobile rom on it.. but i would like to know that if o2 comes up with a new rom upgrade, would i be able to install it directly on my xda exec without doing any manipulations on my xda.. please reply soon.. thankyou.
Hi,
Mine was originally (Monday this week!) an O2 XDA Exec, until the OS got screwed when installing O2's GPRS monitor app fron CD. I have both Installed the Imate beta, and iImate full release, using the mothod described. I haven't tried with the T mobile Firmware yet, as my XDA is working perfectly at present ('if it ain't broke don't fix it !'). I do have a copy of the T mobile F/W stored, if I get a problem or, there are 'features' that would be useful. I can see no reason why it shouldn't install as described in my previous post, BUT I haven't tried it.!If O2 came out some updated firmware, I can't see why you counldn't install it as described. I'm looking for a copy of the original O2 F/W, So I can returned my Exec to its original spec if I need to. Especially as its only 4 days old!
Thank you
I got this working it's a good rom from tmobile and a2dp was working ok cut out a bit and then this morning it was workign amazingly and some bloody chavs came and hit me for no reason and broke my bluetooth headphones. Typical. i'm hoping some superglue will fix them
whats a2dp
A2DP - Advanced Audio Distribution Profile:
The Advanced Audio Distribution Profile in Bluetooth™ specifies the protocols and procedures that define the distribution of high quality audio content, in either mono or stereo on ACL (Asynchronous Connectionless link) channels.
Andy
Please, help me in the following situation
I bought Qtek s100 It turns on only in bootloader mode. What was before I don't know.
Now I try to reflash it via PC. I unpacked rom 1.12 from imate and put there file MaUpgradeUt_noID.exe and then ran it. The utility can't see the device information (it is normal) but it can't see the informatin about the rom I'd like to flash. I click @[email protected] but it says it gather information about the device and nothing happened.
I tried to run again about 20 times, but nothing helped.
I tried to flash it via card using rom-image but there is no invitation to reflash though I flashed via card more than 20 times other htc devices and then everything was ok.
I ran mtty 1.42 and gave command d2s, but it said unknown command. Then I gave d2s command then the device turned off.
I have qtek s110 with broken display. Is it possible to change rom-memory?
Is it possible to get service_manual for magician?
Thanks
First of all, did you back up your current ROM to SD before Flashing new ROM.
1. Yes. It's VERY GOOD. Disconnect your device from PC. You need to insert SD with your ROM to the device and Turn On. Press Power or Cancel button (i didn't realy remeber try all). After that device will flash ROM form SD.
2. No. It's VERY BAD. You need to know start address form what device should start after Reset. Sory here i did not know what it is.
Ñïàñèáî çà ïîìîùü!
Ñóòü â òîì, ÷òî àïïàðàò ñ êîìïà øèòüñÿ íàïðî÷ü îòêàçûâàëñÿ. Ïîïðîáîâàë øèòü îáðàçîì ÷åðåç êàðòó (îáðàç ñíÿò ñ t-mobile 1.01). Íà îáðàç íèêàêîé ðåàêöèè.
Äàëåå ïðîáîâàë ñíÿòü îáðàç ñ ïðîáëåìíîãî àïïàðàòà. Àïïàðàò âûêëþ÷àåòñÿ. Åñëè ñ mtty äàòü êîìàíäó øèòüñÿ s2d, òî mtty ãîâîðèò, ÷òî êîìàíäà íåïðàâèëüíàÿ
Hi,
Read this http://forum.xda-developers.com/viewtopic.php?t=46628 about the SD flash
M
thanks, but te problem is the device doesn't want to work with card. No reaction on the card with rom-image, turning off when typing d2s
Don't know where you bought & how much you paid for it (sure hope it's less then a new screen), but sir I guess you're scr*w*d.
Maybe you can replace your broken S110 screen with the one from the S100. There's a rar file on the board, with a detailed description & pictures on howto disassemble your magician, think it's called disassembly.rar.
EDIT You can find it here http://forum.xda-developers.com/viewtopic.php?t=44841
M
thanks, but I think the screen is alive, it shows usb or serial and etc.
As far as i know, there is some diagnostic tests to understand where is the problem. how to activate it?
Diagnostics
Sorry I don't know of a diagnostics test. But you can have a bootloader without a working rom. Since you bought the S100 in a bootloader state, that's very suspicious to me. & that's why I advised you to replace the broken screen on your S110 with the one from your S100.
Hope you can sort it out & if you happen to run across a diag. pls update the wiki with it.
Regards, M
People,
For a start - i am a fresh newbie and dot have any experience at all in ROMS.
I have read all threads on this tree but decided to do it anyway - just for the fun and experience...
I DIDN'T succeeded on upgrading my jam to wm6 but maybe you will be able to tell me why.
I have download a JasJAR wm6 update and started to play with it a little.
For a start , i have put the Last 113 update(MA_TMNL_11300_132_11200_Ship) and the new wm6 Nk.nbf file together in the same folder - and started the NOid upgrade, for my (very hough )surprise - the upgrade process went exactly like from 112 to 113 meaning all 3 stages from 113 to 2.25 - my heart pumped up for about 30 min until the upgrade completed(64M) - after that all i got is the USB\Serial boot loader.
Is this a stage someone have reached?
If the image could uploaded but couldn't boot - can this be fixed via hack ?
PS - all this started when i wanted the new SPB shell application since it is a very cool looking but works only on WM5...
Thanks
Roy
That's realy interestig... =) Did you tried to upgrade to WM5?
Nope - i didn't reach this stage in WM5....
this thing started when i download the WM6 from mininova...wanted to play with it a little bit.
i tried the original ROMUpgradeUt.exe and it gave me a JAS JAR picture with model number - then i tried the NOid.exe and it gave me a Magician picture with its model number!!! -from there the road was short to try what i did in the above..
what link of file you've been downloaded?
http://www.mininova.org/tor/633101
...for O2 Xda Exec [HTC Universal]
pickiki said:
http://www.mininova.org/tor/633101
Click to expand...
Click to collapse
Have you read Comments....?
http://www.mininova.org/com/633101
same problem sort of
ive got the same phone and when i tried upgrading to wm5 i incountered the same problem, it now wont do anything no matter what i do soft reset, hard reset, take the battery out for an hour. it is stuck in a boot loader screen so i think it might be salageable. but cant find original 2003 windows ver. and cant get it to connect with activesync. although when i do connect it, i do get a connection via usb and get the sound confirmation and pop up. if anyone could help or give me any suggestions it would be great.
Hello!!! =) I've tryed to upgrade to WM6...=) So now it's a brick.. -) I've bootloader screen with word "Serial" and i can't get usb connection.. -(
If someone know how i can resurrect it? =)
=)... 2 hors later it came back! IT'S ALIVE!!! =)
No.. it was jast glitch... -( When i connect my mda to PC and make reset, it shows Usb, but when i disconnect my device, it still shows usb... -(
*lol*
Your "english" just reveals that you're unable to comprehend what has been written so many times before. It's a shame.
Well if it’s any constellation at least you can use your phone to hold down important papers on a desk.
! why are you putting a JASJAR rom on a JAM?
Of course you'l brick it!
And there is NO WM5 OR WM6 COMING EVER FOR THE MAGICIAN!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
go and flash the original ROM and never come back on XDAdev
omg im laughing so hard i can hardly post.
st3v3 said:
omg im laughing so hard i can hardly post.
Click to expand...
Click to collapse
Same with me (except for these few words)