Hello, I am looking for the solution to the problem of my HTC PROPHET (SPV M600 model) that does not start. In detail what I have already done:
1) I made the procedure HARD RESET following the guides published on the forum.
2) I made the procedra of BOOTLOADER and loaded Rom (I tried with several Roma) following the guides published on the forum.
3) ActiveSync 4.5 installed.
The result is that the device will not start: the screen appears with the logo of the rom (Orange or HTC) and IPL data, SPL data, etc etc, but sometimes or remains firm on this screen, or other times the screen fades plan floor.
What can I do?
Best regards
Marco
Did u already tried another rom? Which rom did u use?
Is activesync still connecting with your device?
i tried with rom of:
1) Orange
2) Qtek
3) I-Mate
the first two i can install correctly, but device don't work... when i try to install rom I-Mate, it give error message about nk.nbf file isn't compatible with prophet. i know about a program NOID COUNTRY that install every rom on prophet... do you know this program?
pincho76 said:
i tried with rom of:
1) Orange
2) Qtek
3) I-Mate
the first two i can install correctly, but device don't work... when i try to install rom I-Mate, it give error message about nk.nbf file isn't compatible with prophet. i know about a program NOID COUNTRY that install every rom on prophet... do you know this program?
Click to expand...
Click to collapse
Check on boot loader that ur device did HardSPL properly, it should look like my sig.
Also why are you trying to put OEM ROM on, why not use one of the prophet wm6/wm6.1?
Hello,
after reading your post, I rebuilt the hardreset and then starts in bootloader, but does no more. I tried with any Rom, but always starts in bootloader (IPL 2.10.0001 - SPL 2.20.0001 indicates that is a G4 right?)
is dead? because I really tried with all Rom at my disposal, but the result is this hour.
pincho76 said:
Hello,
after reading your post, I rebuilt the hardreset and then starts in bootloader, but does no more. I tried with any Rom, but always starts in bootloader (IPL 2.10.0001 - SPL 2.20.0001 indicates that is a G4 right?)
is dead? because I really tried with all Rom at my disposal, but the result is this hour.
Click to expand...
Click to collapse
It would appear that your hard SPL was not sucessfull, it should say something like SPL : 2.G4.4PDA (or something similar)
Yes you have a G4 model. what were the steps you took to do SPL? did you follow the guide? Did you unplug all ur usb connections and try other usb ports?
If you start bootloader and connect your usb to device does it say USB on the screen? Also are you using windows XP on computer?
timmymarsh said:
what were the steps you took to do SPL? did you follow the guide? Did you unplug all ur usb connections and try other usb ports?
Click to expand...
Click to collapse
I followed the guide on PROPHET_HARDRESET_BOOTLOADER on WIKI: the operation seems to succeed because I see the message on the display of operating system restored. Tested with all the usb ports, and disabling the connection usb dall'activesync.
timmymarsh said:
If you start bootloader and connect your usb to device does it say USB on the screen? Also are you using windows XP on computer?
Click to expand...
Click to collapse
USB appears on the display and use xp.
I noticed that when upgrade Rom program start, I see on the display a green bar progress, but turns red when it arrives 99%-100%. It may mean that something is not successful, despite the process ends without mistakes?
What is the devices IPL/SPL, and what brand is the device?
l3v5y said:
What is the devices IPL/SPL, and what brand is the device?
Click to expand...
Click to collapse
Hi!!!!
sorry for late answer....
IPL:2.10.0001
SPL: 2.20.0001
GSM: 02.47.21
OS: 2.10.1.22
Brand: Orange
after installing the latest rom Orange, these are the data that appear on the monitor. But still not start. It remains firm on this screen, or this screen fades slowly as reported in a previous post.
From tomorrow I will be on vacation, return to this issue by September 1 ....
a greeting and goodbye to September 1 !!!!!
pincho76 said:
Hi!!!!
sorry for late answer....
IPL:2.10.0001
SPL: 2.20.0001
GSM: 02.47.21
OS: 2.10.1.22
Brand: Orange
after installing the latest rom Orange, these are the data that appear on the monitor. But still not start. It remains firm on this screen, or this screen fades slowly as reported in a previous post.
From tomorrow I will be on vacation, return to this issue by September 1 ....
a greeting and goodbye to September 1 !!!!!
Click to expand...
Click to collapse
If you have the time, download and flash an NVID Prophet ROM from the wiki. Make sure it's NVID though!
l3v5y said:
If you have the time, download and flash an NVID Prophet ROM from the wiki. Make sure it's NVID though!
Click to expand...
Click to collapse
Hello!!!!
i'm coming back from Paxi (Greece)... very nice island... good sea... good food... very nice gals.... i liked it!!!!!!
Downloaded from Wiki "RUU_Prophet_220734_2207114_024721_NVID" and installed without problem but nothing to do: the same problem!!!
Now when it start i can see first HTC Innovation Logo, after QTECK logo with:
ipl: 2.10.001
spl: 2.20.0001
gsm: 02.47.21
os: 2.20.7.34
but after some minutes the screen fade....
i would give you some information:
- into the device ther's not memory card and sim card.
- when i charge it, led is always red, also if leave in charge for 10 hours!!! It's normal???
Ciao
Marco
If the LED is red, I'd try and find a replacement battery.
read from here http://wiki.xda-developers.com/index.php?pagename=HTC_Prophet
and here http://forum.xda-developers.com/showthread.php?t=353547
read carefully ok...
Related
Thanks! andot! for best rom.
Base on Windows Mobile 6 for Typhoon/Feeler/Amadeus WWE Edition Released!
.................................................. .....
Remove nina.ttf, ninab.ttf,unisun.ttf.
Edit default.hv
Add segoe.ttf,segoeb.ttf.
.................................................. .....
Rom for Feeler.
http://rapidshare.com/files/52685670/WM6_English.rar.html
Rom for Typhoon.
http://www.thupload.com/download/8f60f9b6c777738030149ddc520d5272.html
More.
http://download.coolcode.cn/typhoon/Extra.zip
Nice work!
Creative7419 said:
Thanks! andot! for best rom.
Base on Windows Mobile 6 for Typhoon/Feeler/Amadeus WWE Edition Released!
.................................................. .....
Remove nina.ttf, ninab.ttf,unisun.ttf.
Edit default.hv
Add segoe.ttf,segoeb.ttf.
.................................................. .....
ROM.
http://rapidshare.com/files/52685670/WM6_English.rar.html
More.
http://download.coolcode.cn/typhoon/Extra.zip
Click to expand...
Click to collapse
DID YOU GET THE CAMERA WORKING?
what is the difference between the rom from andot becuz remove nina.ttf doesnt say much to me. filesize is excactly the same as andots rom
hey, so what's with the camera? any success?
camera app in http://download.coolcode.cn/typhoon/Extra.zip is updated.
yep, got it, thanks! and is there any chance to get media buttons work? has anyone tried to use keyboard driver from ronswens' wm5 amadeus build?
Hi Creative7419/Andot,
Is it indeed stable after e.g. changing Home Screen options, activesyncing and switching the device on and off a few times? And: did you use the most recent SPL (1.01.0109) or the older (1.01.0064) version?
SFC said:
yep, got it, thanks! and is there any chance to get media buttons work? has anyone tried to use keyboard driver from ronswens' wm5 amadeus build?
Click to expand...
Click to collapse
only fixed 0.3 camera app.
keyboard driver from ronswens' wm5 amadeus build can't work in wm6.
We need to modify the wm5 keyboard driver for wm6 amadeus.
wirelezzwizzerd said:
Hi Creative7419/Andot,
Is it indeed stable after e.g. changing Home Screen options, activesyncing and switching the device on and off a few times? And: did you use the most recent SPL (1.01.0109) or the older (1.01.0064) version?
Click to expand...
Click to collapse
I suplied 27M 1.01.0109 SPL & 1.01.0064 SPL.
you can flash ROM from 27M 1.01.0109 SPL, then enter the WM6, flash 1.01.0064 SPL, and then when you reboot your phone, you will not see the red text.
andot said:
I suplied 27M 1.01.0109 SPL & 1.01.0064 SPL.
you can flash ROM from 27M 1.01.0109 SPL, then enter the WM6, flash 1.01.0064 SPL, and then when you reboot your phone, you will not see the red text.
Click to expand...
Click to collapse
Andot,
I had 1.01.0109 SPL on my Feeler and flashed 'back' to 1.01.0064 SPL. Now I get the red, green and blue screen (red: Typhoon IPL 1.00, green: Typhoon 1.01.0064 and blue: just Typhoon, nothing else) and I cannot load the new WM6 ROM.
I hope I did not brick my device. Any suggestions?
If you find 1.01.0064 SPL not support your device, you can flash 1.01.0109 SPL back. your phone os will come back.
andot said:
If you find 1.01.0064 SPL not support your device, you can flash 1.01.0109 SPL back. your phone os will come back.
Click to expand...
Click to collapse
How to flash back to 1.01.0109 SPL? As far as I know you need to be ActiveSynced with the device and - as you can guess - I only can get in the red-green-blue screen of 1.01.0064 SPL.
wirelezzwizzerd said:
How to flash back to 1.01.0109 SPL? As far as I know you need to be ActiveSynced with the device and - as you can guess - I only can get in the red-green-blue screen of 1.01.0064 SPL.
Click to expand...
Click to collapse
Please look at this to flash your device to 1.01.0109 SPL.
=====
SPL 1.01.0109
Your smartphone must be activesynced with the computer.
[*]Download IU_SPL+PatchedRUU.zip from here.
[*]Extract all the files to some folder on the PC and run Patched_RUU.exe.
[*]Follow the instructions and it will flash SPL 1.01.0109 to your phone.
=====
Already solved the problem. Solution: just in case other people get the same problem
1. Get into bootloader mode for 1.01.0064 SPL (the red-green-blue screen)
2. Run USB connection with MTTY 1.42
3. Press Enter to see Cmd prompt
4. Type info 2 and press Enter
5. Type format BINFS and press Enter
6. Now you can run 2003SE official ROM
After this you can flash back to 1.01.0109 SPL and install WM6 ROM
wirelezzwizzerd said:
Already solved the problem. Solution: just in case other people get the same problem
1. Get into bootloader mode for 1.01.0064 SPL (the red-green-blue screen)
2. Run USB connection with MTTY 1.42
3. Press Enter to see Cmd prompt
4. Type info 2 and press Enter
5. Type format BINFS and press Enter
6. Now you can run 2003SE official ROM
After this you can flash back to 1.01.0109 SPL and install WM6 ROM
Click to expand...
Click to collapse
hi! can you give me a link to an official O2 xphone IIm rom? i cant find one.... thanks!
Do not have that ROM, I found a Qtek which worked ok as an intermediate step to get back to ronswens WM5
Bricked Feeler
I try to flash my Qtek 8020 with WM6 Rom, but at 68% stage of flashing my PC updater window missing from my desktop. I retry to start updater, but without any succes, of course.
Now, my device is death.
Anybody has a solution for this ?
Please, this smartphone is in a very good condition (is new one, 0 min. talking, in fact ) ,i don't want to drop it.
Thanks !
Sorry for my bad english, this is not my usual language
i think this might work bcos it happend when i tried to upgrade to WM6 on ma typhoon.... do as following... n within no time it will be workin again.......
Now you need to access the bootloader. Ensure that the phone is turned off, hold the camera button with a hand, and connect the USB cable, after a second, you will see a white screen asking 'Need an IU? ", press 0 and you will see a 3 colour screen which is the bootloader.... Now extract the ROM which you have downloaded earlier on to your C: drive, then execute mtty.exe. Select USB from the drop down menu and click OK..... Copy os.bin into C drive. Now type 'l c:/os.bin' without the quotes and type enter, you will see a series of process. The entire process takes around 10-20 minutes. Please be patient. Once it is done, type ResetDevice, and you have WM6.
Creative7419 said:
Thanks! andot! for best rom.
Base on Windows Mobile 6 for Typhoon/Feeler/Amadeus WWE Edition Released!
Rom for Typhoon.
http://www.thupload.com/download/8f60f9b6c777738030149ddc520d5272.html
Click to expand...
Click to collapse
The typhoon link doesn't work. Could you please update it?
Moreover I've got a question: i'm now using andot's rom, in english so when i change rom to yours, the only thing that is gonna change is the font, right?
cheers
greg
HI,
Thanks for POF and other forum members.
I upgraded my DOPOD C800 with WM6. Used POF HARD-SPL and Official HTC P4350 ROM.
Thanks
Jose
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
murali509 said:
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
Click to expand...
Click to collapse
Hi mine is- before upgrade
SPL 1.09.0001
IPL 1.09.0001
ROM 1.7.707.3 WWE
ROM Date 11/01/06
Radio 2.69.90
protocol 4.1.13.30
Ext rom 1.7.707.106
OS 1.7.0.0
I also have a Dopod C800 with the same ipl & spl. Can you direct me to the POF Hard-Spl files that you used? I have the HTC P4350 WWE WM6 RUU. Any help is greatly appreciated...scared to death I'll brick the phone!
How i upgraded My DOPOD C800
STEP I:
Download the following files
1) USPL --- Flah centre.rar file from
http://www.mediafire.com/?axtm5qlmbli
2) Official RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe
3) Make sure ur computer is always power on...not hibernated
Step II:
1) Create 2 folders eg:flash and rom.
2) Extract flash centre.rar in flash folder
3) Extract HTC_P4350.... ship.exe in rom folder .
( Use winrar or simply double click the file. It will start the upgrade window ,click next, then hold.Go to the temp folder, u will find all the extracted content there.Copy all the content to the new rom folder. After that cancel the upgrade window.)
4)After extracting the content in the rom folder ,*****delete the SPL.nbh file ****
Step III:
Connect your phone to the computer, make sure activesync is enabled (green icon)
Step IV
1)Open the flash folder --- follow the read me file in this folder
ie
2)Run herald-uspl.exe on your computer and follow the instructions on screen.
- it will run in command window and ask u to enter the values..follow the screen
After 2/3 steps if will ask u to chk the device-- the activesync green icon in ur computer will become grey and the screen of ur mobile will be blank-white.
!!! now u have sucessfully hard spl ur device!!!
**** dont touch or remove the connection or close any program****
3)After this it will start the RUU program ,follow the instruction ,click update ( u wont find any previous ROM installed),it may or will show ERROR [240] : FILE OPEN
clik finish/cancel and exit **this program only**.
4)Now without removing anything open the rom folder and clik the ROMUpdateUtility.exe file and follow the instruction.
thats it. ur mobile will be upgraded. dont get panic...it will take some time and the mobile will be white in colour.
Thanks
Jose
C800 upgrade success
Upgraded Dopod C800 with same IPL/SPL/RADIO parameters as mjose using his directions and it worked like a charm. Am WM6 with no issues now.
Thanks POF and mjose and everyone else on the forum for your help!
WHen using Herald-USPL - it is NOT permanently HARD-SPL!!!!
Please check the SPL now - and report....
if it doesn´t show 4.70.yang - then it is only USPL = temporarly CIDunlocked= NOT HARD-SPL
thx.
How much free memory did you get by upgrading to official HTC WM6? I got only 25mb free with no extended rom install!
C800 USPL vs Hard SPL
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
billy-the-t said:
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
Click to expand...
Click to collapse
nope. BUT try USP for falshing an official HTC rom with higher SPL and then HArd-SPL....
NICE! I successfully upgraded my C800 to wm6 using mjose instructions. Thanks to mjose and to all those involved.
Thanks to mjose, UPGRADED
Followed exactly what mjose said. Successfully upgraded. Thanks to everybody
Any idea how to install touch flo now?
C800
ROM: 4.17.405.2 WWE
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
longj49 said:
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
Click to expand...
Click to collapse
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
longj49 said:
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
Click to expand...
Click to collapse
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
mv3 said:
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
Click to expand...
Click to collapse
hey thanks! yes. i've got the asian herald. i got into bootloader mode as per your suggestion - is that the one with red/green/blue horizontal bands with a thinner white band at the bottom? ok what should i do next?
i was able to run the ROM Update utility after that, but got an error 300. checked the documentation and found out that i used the wrong version for my phone, which was RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe. would you know which one i should use?
i'm guessing your phone is not an English phone?
you need to find the native RUU for your phone.. Taiwanese Mandarin> HK Traditional? Japanese?.... if you can find it, then put your phone into bootloader and run the RUU file from your pc.
other than that, I don't know if anyone here has access to asian RUU's
doesn't look good, can't seem to find my region's wm6 rom anywhere. even tried to restore using the original wm5 rom from htc website, but still getting error 300. i think running herald-uspl.exe initially could have somehow caused some corruption.
well, i might have to visit dopod's service center soon.
thanks for your help, mv3, greatly appreciated.
did you try looking for official ruu from asia.htc.com
I suggest you load that before going to the repair centre
hi, i was upgrading last nite and i really don't know what i did and what happened, my prophet is stuck at RGB, it does not do anything else, can't even load windows nor connect to active sync. is it bricked? please help
What are the IPL and SPL?
Read this: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
i have a G3
IPL: 2.20
SPL: 2.20
edit: i tried that guide but it does bot connect to active sync
Before or after the RUU?
If it's before, it shouldn't matter...
before, and i did not RUU, because it can't connect to phone
In the bottom left hand corner of the screen, some text should say "USB" if it does, your good to flash a ROM.
yes it does say USB, which ROM should i flash? wm5 or wm6? or should i RUU?
Flash the WM5 ROM linked to in the wiki page.
ok thnx i am currently flashing that ROM now and will tell you the results
thanks i successfully flashed the ROM. can you now please tell me how can i flash wm6 ROM?
Read the "NEW WM6 upgrade guide" that is a sticky at the top of the Prophet Mobile Six forum.
i'm stuck at this step where it says
go to the ExtRom folder. (Look at the picture) you will find ExtRom folder in most of the wm6 roms. when you download a wm6 rom, this folder is usually beside the Upgrade_ROM.bat .
please help what to do
If you have a new (almost all WM6.1 ROMs) ROM, it should be a single file. It should be "nk.nbf" if this is the case, you do not need to prepare the file.
You will need to HardSPL your device and then flash the ROM.
ok i did it. thank you very much
hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
?
tried flashing with HTC_1.12.405.01_026790_WWE_SHIP says invalid model...
T-Mobile dead loop ?
I have similar problem with my artemis. I have a HTC P3300 from T-Mobile. It started with switching itself out, then it didn't want to boot, then it began to hang on bootscreen and at the moment i cannot start it at all (even the battery is fully charged and it is pluggen in my PC).
I suspect that T-mobile build in a dead loop somewhere in the software or hardware. It looks very suspicious to me that both mdas i had from T-Mobile start to make problems exactly a month or or two after the warranty is expired. and the problems develop in the same way in deteriorating manner.
It could be that the hardware cannot take it anymore and it starts to deteriorate exactly after the second year (handy for two years contracts).
Does anyone similar experiences or anyone solved that problem.
Sorry mates I cannot provide you with any info about my PPC (radio, rom version etc.) because I simply cannot get so far to be able to see that information.
Looking forward hearing from you
Cheerz
Hi, my problem is similar, but I need the ROM in ITAlian.
Information about my cellphone:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
Any ideea how to download this ROM? Pls help.
Thanks, Fernando.
Here the same...any one help?
kappp13 said:
hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
Click to expand...
Click to collapse
Have you tried the CMON USPL? It's on Shady's ROM (the lite one) run this first! Be in Bootloader. Hold the Record Key (left key) and by holding that press Power key to switch on! Then try to Update your ROM
Hello guys, I've got a p3300 which I can't update to a WM 6.1. It's the factory's 6.0. It's originally simfree so I dunno if I need to go through the USPL.
The thing is that it gives me 270 Corrupted image error.
As I thought that being simfree originally, didn't need to do CID unlock, I tried to flash a cooked ROM with no success whatsoever.
Any ideas?
Kind regards,
JamworkS.
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Having problems with this.
For 2 days I try all the files and ways to set 1.11.cmon on my P3300 and always stuck at one place no matter what versions of the program I get.
IPL 3.07.0001
SPL 1.11.0000
GSM 02.98.90
OS 3.13.0.0
are the red numbers I see when I restart it.
The problems are that when connect phone and see connected on ActiveSync I start start_uspl program. After 100% connection with Active Sync dissapears and I see black screen on my PPC, then I run ROMUpdateUtility and It says some error that there is no phone connected.
If I start ROMUpdateUtility before start_uspl I go in to boot loader mode ( the 3 colors screen ) and then again that there is no phone connected.
I have done this 15 times or more with different versions of the program and it stucks on the same places ALL the time no matter what version I use.
My artemis had 1.11.cmon before, but I installed the LAST Artemis P3300 ROM from the WIKI. That removed the 1.11.cmon from the phone. After that I have Installed Vanilla 2.0 WWE version on the phone and started the process to set 1.11.cmon on the phone. No success. After some 6.5.5 ROM from the forum, then process to set 1.11.cmon and again nothing...
Please HELP!
i am also having the exact same problem with this , have tried everything to get this to work.
iant2008 mate I did solve the problem
All works as the brains here say. My problem was that I am using Windows 7 at home and Windows Vista at other place I did try to fix this problem. However with Windows XP this whole operation works properly as the people here say. Big thanks to them and I hope you success in this operation too
raving_nanza said:
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
- Cert_SPCS
- EnableRapi
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Click to expand...
Click to collapse
* soft reset after 100% when the rom update utility window opened on pc..
''to get activesync connection''
it should work dude
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
...
sameeha said:
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
Click to expand...
Click to collapse
put the 2cabs on your device and run them..
rapi & cert
run_startuspl - on pc
when this is 100% - soft reset device
-now continue to do rom update utility (uspl ruu)
this should work..?
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
...
sameeha said:
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
Click to expand...
Click to collapse
i have to admit, i had same trouble to do uspl1.11cmon but eventually it worked.. frustrating.. i know.. but keep trying.. if i was you i would flash back to the official rom.. which should get rid of 1.11.0000 and set back to original spl..
i put rapi and cert on my device, ran them, connected to pc, ran ''run_startuspl'' that made penguin on screen on device.. went to 100% then white screen.. Ruu automaticly opened on pc but i didnt continue with Ruu.. i soft reset device, got activesync connection again and then i continued with the open Ruu..
(Ruu - rom update utility)
Thanks RN, you know, I was trying all this time and my Artemis frozen now (freezes on startup screen IPL 1.25.0001 / SPL 1.27.0000 / GSM 02.69.90 / OS 3.4.0.0. and dopod logo) not moving further. Whats going on? Can you help me?!
Cheers,
Sameeha
...
add me to messenger..
will be much easier than posting
i'm an idiot.....
see this thread
http://forum.xda-developers.com/showthread.php?t=578406
if you run a 3.13 rom; get the 3.13 cmon
if you run a 3.15 rom; get a 3.15.com.
pof's original (kickass great work!!) didn't work with my 3.13 (original htc rom); i ended up with 1.11.000spl. i then ran the 3.13 uspl (see thread); now i am on cmon version